RGB LED wallwasher-User Guide.cdr
Contents
1. e Maximum Series wound Length 100 meters 328 feet Master Signal Amplifier is needed at every 100 meters 328 feet Installation Steps e Place X30T RGB LED Wall Washer at the required locations and aim them according to your lighting design e Adjust the rotary angle to required angle e Connect X30T RGB LED Wall Washer to each other Signal Amplifiers are needed every 100 meters or 328 feet e Finish waterproof treatment at every signal connector joint Please refer to picture below fo ee can Tape Heat Shrink Heat Gun 4 _ e Connect the DMX Console to the first X30T RGB LED Wall Washer e Plug the first X30T RGB LED Wall Washer and DMX console into power outlets to power the system 2 4 www ledworldlighting com Phone 800 387 4081 Email sales8 ledworldlighting com IED D wumledwerddlightiag coa RGB LED Wall Washer Planning Suggestions Consult an electricalinspector when reviewing all wiring plans Create alayout plan blueprint pera lighting designer s or architect s recommendations Installation Considerations e Button Functions Button Control Mode Function Example 8 18 8 DMX Control Displays the DMX address selected valid DMX addresses from 001 512 e 5 6 Self Control Displays the color changing mode and speed selected P self control X mode Y speed P oH OY A DMx Control Select a parameter for configuration Self Control Select mode or speed for configuration DMx Control Set corre2. User Guide RGB LED Wall Washers NOTE The purpose of this user guide is to explain the necessary steps for use of X30T RGB LED Wall Washer and to assure peak performance of product It is intended for use as reference by a fully qualified electrician or technician This document should never be considered a substitute for any provision of a regulation or state orlocal code Please read this manual to fully understand and safely use this product Specifications are subject to change without notice GETTING STARTED This guide contains important information about installing and operating X30T RGB LED Wall Washer Included in this Box X30T RGB LED Wall Washer 1 Pcs User Guide 1 Set Additional Items Needed Control System RGB DMX Controller Signal Amplifier Master Signal Amplifier Unpacking e Unpack and carefully examine the product e Report any damage and save all packing materials if any part of the apparatus was damaged during shipping e Donot attempt to use this apparatus if itis damaged Cautions e Warning Risk of electric shock Ensure that the power supply is off when wiring or soldering the device during installation e The device should be installed and operated by a qualified electrician or technician in accordance with relevant localcodes e Donotuse sharp tools near or on the surface of the device e Suggested continuous working time is around 8 hours Never use for more than 12 consecutive hours User Responsi
3. bilities The responsibility of complying with all state and local laws ordinances and regulations in regards to the installation maintenance and operation of the device lies with the buyer and handler of the device These parties may include but are not limited to the contractor installer purchaser owner and user of the product Note The instructions and precautions set forth in this user guide are not necessarily inclusive of orrelevant to allapplications as LED World Inc cannot anticipate all possible situations 1 4 www ledworldlighting com Phone 800 387 4081 Email sales8 ledworldlighting com IED D wumledwerddlightiag coa RGB LED Wall Washer PLANNING THE INSTALLATION This device installation requires planning to ensure timely installation with minimal complications and down time Planning Suggestions Consult an electricalinspector when reviewing all wiring plans Create alayout plan blueprint pera lighting designer s or architect s recommendations Installation Considerations When creating your installation plan consider the following e Location of the device X30T RGB LED Wall Washer is suitable for only dry wet and damp environments e Control System X30T RGB LED Wall Washer can be controlled by our RGB DMX Controller LT 840 Synchronous color changing might be considered before installing e Lighting Distance The maximum lighting distance for X30T RGB LED Wall Washer is around 15 meters 49 feet
4. ne DMX Out I AC Power Max 100m 328ft in series connection 120V 60Hz DMX Out AC Power 120V 60Hz RGB Wall Washer DMX Out AC Power 120V 60Hz 4 4 www ledworldlighting com Phone 800 387 4081 Email sales8 ledworldlighting com IED tD wumledwerddlightiag coa
5. sponding parameter B Self Control Set corresponding mode speed e Howto change settings in DMX Control mode Once the wall washer is connected to the DMX console it will access DMX Control mode Press button A to select a parameter for the DMX address Press button B to change the DMX address Valid DMX address range 001 512 Refer to the user guide of the DMX Console for more detailed information on operating the DMX Console Each wall washer occupies three DMX channels including red green and blue For example the wall washer at DMX address 001 occupies channels 1 2 and 3 the wall washer at DMX address 256 occupies channels 256 257 and 258 X30T RGB LED Wall Washer can be controlled by our RGB DMX Controller LT 840 Synchronous color changing might be considered before installing e How to access and set under Self Control mode Press button A four times This will access Self Control mode and the letters PXY will be displayed Press button A once The digital LED should start to flash and you will be given access to the corresponding setup mode Press button B to change the corresponding setup speed or brightness The digital LED should display values 1 through 9 Master Slave Mode O Choose one wall washer as the master and set its DMX address to 001 O Choose other wall washers as slaves and assign them any DMX addresses except 001 O Pressbutton A of the master wall washer four times to acce
6. ss Self Control mode O Change the mode of the master wall washer All slave wall washers will work synchronously with the master 3 4 P X mode 1 Static Red 2 Static Green 3 Static Yellow 4 Static Blue 5 Static Pink 6 Static Cyan 7 Static White 8 Multi Color jumping 9 Multi Color fading A Multi Color flashing Y speed brightness 9 brightness levels brightest at 9 9 brightness levels brightest at 9 9 brightness levels brightest at 9 9 brightness levels brightest at 9 9 brightness levels brightest at 9 9 brightness levels brightest at 9 9 brightness levels brightest at 9 9 speed levels fastest at 9 9 speed levels fastest at 9 9 speed levels fastest at 9 www ledworldlighting com Phone 800 387 4081 Email sales8 ledworldlighting com WS RUD wumledweddlightiag coa RGB LED Wall Washer e How to exit the selected mode Press a button of your choosing and wait for around 10 seconds for the device to exit from selected mode The digital LED will stop flashing and the wall washer will retain the currently the selected mode and parameter Wiring Diagram DMX Controller HUEDA a Od a 2 8888 Power faa DMX Data pe Output DMX Out Class 2 Low Voltage Driver L N V AC Power 120V 60Hz v AC Power G 50 60Hz RGB Wall Washer DMX Out AC Power 120V 60Hz DMX Out AC Power RGB Wall Washer e
Download Pdf Manuals
Related Search