USER'S GUIDE
Contents
1. e For the cleaners used in areas that have a lot of sand the cleaner may need to be rinsed with water at all flapper filter bucket s flapper is at intake port areas and may need rinsing at the dome push button to allow free operation e Cleaner may get stuck if a high main drain is installed in the pool Cleaner may remain lodged on the drain for a short period of time but will eventually free it s self by virtue of the cleaner s embedded program 12 Troubleshooting continued The filter bucket is designed to be cleaned with the filters installed for normal clean up For deep cleaning the user can remove each filter cartridge and clean separately During the normal operating cycle of the cleaner the handle side of the unit will rise from the pool bottom to allow the unit to clear obstacles such as elevated main drains and stair steps It is normal to see the cleaner ride the wall for a short period of time this allows the unit to change position in the pool to assure full bottom coverage Perception of cleaner performance Confusion may exist over the perception of how the cleaner operates at different times during each cycle It is important to judge the performance of the cleaner by observing improved pool cleanliness after the cleaner has run a complete cleaning cycle If a cleaner has poor coverage of the pool in one cycle or only covers a small area check the filter and clean if necessary and make sure the unit is not get2. 16 INEEN NES N ENE N ENE N DOL N 2 Roera aora 2 roer 3 roer ron E A O E f roaz roes Roens 2 rovers Ju roxo Reese s roes is Roero fos nor 25 roxo 15 Roes e Roe is roen 2 rovers 36 roxo se Roer 7 rose soe far soen or roson er rora fe roes is Roens foe Rowers 2 roro Roer fa roer soe es Reverse 20 roxo rosana 10 Rorera foo soes fe roxana ao Roxseo02 Rorera HAYWARD POOLCANADA 2880 Plymouth Drive Oakville ON L6H 5R4 d 1 888 238 7665 www haywardcanada com
3. Congratulations on your purchase of a microprocessor controlled fully automatic pool cleaner AquaVac represents the highest standard in design performance and quality This manual contains important information regarding the operation and maintenance of your cleaner PLEASE READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE PUTTING YOUR CLEANER INTO USE Deterioration discoloration or brittleness of any pool finish can be caused over time separately by or in combination with age incorrect pool water chemistry improper installation and other factors Customer hereby disclaims any and all claims and releases Manufacturer from any and all claims for damages to any pool plaster or vinyl liner in Customer s pool by reason of the use and or operation of the Cleaner Under no circumstances shall the Manufacturer be liable for any loss or damage whether direct consequential or incidental arising out of the use or inability to use the cleaner in Customer s pool Warning This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety It is mandatory to allow a safety distance between the power supply and the pool as required by the current installation standard 3 5 m minimum to respect the NF C 15 100 standard F
4. to frost and to chemicals Any other costs transport labour etc are excluded from the warranty HAYWARD may not be held liable for any direct or indirect damage resulting from incorrect installation incorrect connection or incorrect operation of a product In order to claim on a warranty and in order to request repair or replacement of an article please ask your dealer No equipment returned to our factory will be accepted without our prior written approval Wearing parts are not covered by the warranty EXCEPTIONS AND EXCLUSIONS FROM WARRANTY The cleaner must be used with electrical requirements as indicated on the Power Supply Otherwise damage defects malfunctions or other failures of the cleaner arising from use on electrical supply not as indicated are excepted and excluded from this warranty Defects malfunctions failure or damage of the cleaner caused by improper unreasonable or negligent use or abuse by the consumer are excluded from this warranty If any repair is made on your cleaner by anyone other than authorized personnel designated to perform such work without first having obtained factory instructions HAYWARD at its sole option may determine that this war ranty will not apply and that reimbursement for such repair will not be made because of failure to comply with such factory specified instructions Filter cartridges are not covered by this warranty and will be replaced only with your prior approval of the charges
5. AQUAAC A HAYWARD COMPANY USER S GUIDE CE Hayward Pool Products Canada 2880 Plymouth Drive Oakville ON L6H 5R4 1 888 238 7665 www haywardcanada com Important Safety Precautions Attention User This manual contains important information that will help you in operating and maintaining this pool cleaner Please retain it for reference WARNING Before installing this product read and follow all warning notices and instructions which are included Failure to follow safety warnings and instructions can result in severe injury death or property damage Consumer Information and Safety This pool cleaner is designed and manufactured to provide safe and reliable service when installed operated and maintained according to the information in this manual Be sure to read and comply with all of the warnings and cautions N DANGER Risk of electrical shock or electrocution The electrical supply to this product must be installed in accordance with all applicable local codes NF C 15 100 for France and ordinances Improper installation will create an electrical hazard which could result in death or serious injury to pool users or others due to electrical shock and may also cause damage to property MA WARNING Do not play with cleaner or cable or apply to body Can trap or tear hair or body parts Cable can trip or entangle swimmers which could result in drowning A WARNING Do not allow swimmers in the pool while pool clean
6. EATURES The cleaner independently scrubs vacuums and filters your pool No installation no attachments Just drop it in and turn it on It is completely automatic Filter cleaning is much easier with the top access filter cartridge element Adaptive Seek Control Logic ASCL Microprocessor control optimizes cleaning routine for each individual pool size and shape Electronic Self Diagnostics and Overload Protection Simple Direct Drive design w non corrosive bearings for high reliability GENERAL OPERATING INSTRUCTIONS Take a moment to get familiar with the cleaner using the figure 3 Throughout this manual reference to this figure is made when referring to different components of the cleaner ES Fig 1 Remove the cleaner by placing the carton e down and removing it from the box as shown The cleaner and the Power Supply is gt Ol premounted to the cart See the figure 4 for A A CER Caddy Cart 1 Select the nearest 220 240 volt AC outlet that is close and protected from short circuits Fit a 30 mA differential protection device to protect people from electric shock caused by a possible break in the electrical insulation 2 Place the power supply so that it is at a minimum distance of 3 5 meters from the pool edge The length of the standard cable is 15 24 meters 3 Connect the floating cable to the power supply Use only the original Power Supply manufactured by Hayward 4 Place the cleaner in the pool It w
7. HE POOL AGAINST THE SIDE WALL THIS COULD DAMAGE UNIT AND OR YOUR POOL WALL DO NOT BURY CORD REPLACE DAMAGED CORDS WARNING TO REDUCE THE RISK OF INJURY DO NOT PERMIT CHILDREN TO USE THIS PRODUCT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES IF THE SUPPLY CORD IS DAMAGED IT MUST BE REPLACED BY THE MANUFACTURER ITS SERVICE AGENT OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD While the cleaner has been made to operate as safely as possible we suggest you exercise reason able care in the handling of the vacuum and inspect the electrical cord frequently for damage or wear as with any other electrical appliance After use remove the unit and rinse with fresh water and remove any twists that may be present in the cord 15 Limited Warranty All HAYWARD products are covered for manufacturing defects or material defects for a warranty period of 1 year as of date of purchases Any warranty claim should be accompanied by evidence of purchase indicating date of purchase We would therefore advise you to keep your invoice The HAYWARD warranty is limited to repair or replacement as chosen by HAYWARD of the faulty products provided that they have been subjected to normal use in compliance with the guidelines given in their user guides provided that the products have not been altered in any way and provided that they have been used exclusively with HAYWARD parts and components The warranty does not cover damage due
8. ach use Keeping the cleaner permanently in the pool may result in additional service requirements OO FP Ww PSO Power Supply Floating Cable Handle On Off Switch Filter Cartridge Drive Track Wheel Tube 8 Wheel Brush 9 Sealed Motor Unit 10 Side Panel 11 Dome Assy 12 Filter Bucket 13 Wheel 14 Filter Door Fig 3 Caddy Cart Instructions See Diagram Caddy Cart will come partially assembled in the carton less the handle amp tube Insert the screw into the tube at the base of the caddy cart amp secure with bolt 3 Insert the handle into the top of the tube amp insert the screw securing it with the bolt 4 Maintenance Clean the filter cartridge after each use Open the cleaner by pressing the lid button and lifting up the dome cover Remove the filter bucket assembly by lifting it up out of the cleaner with both hands from each side Flip the bucket assembly over to remove the debris and then rinse with a garden hose to remove small particles Filter cartridges do not need to be removed to clean To Remove the filter cartridges Unsnap and lift up both filter door latches 4 Pull out the filter cartridges Using a garden hose with a spray nozzle wash the filter elements to remove debris Hold the filter elements as shown to allow the debris to fall out Wash the entire filter bucket assembly Previously shown Place the filter cartri
9. cartridges should be thoroughly cleaned after each use or as often as needed to ensure cleaner s optimal performance Before using your cleaner and especially when opening the pool for the first time remove larger items from the pool that may diminish the cleaner s performance Clean filter frequently when pool is excessively dirty For the first use run cleaner for the full cycle 2 hours to ensure a clean pool and give yourself a full understanding of the cleaner s capabilities Subsequent cleanings may take less than a full cycle Cleaner may periodically go to the wall but not necessarily climb to the vertical position This is a normal part of the programmed cycle Cleaner may stop in the middle of the pool and reverse during cleaning cycle This is a normal part of the programmed cycle DO NOT start cleaner out of the water Power button should only be switched to On position when unit is submerged The unit will automatically shut off but it is best to put power switch in OFF position when unit completes cleaning Plug in only to a protected 120 volt AC outlet that is close and protected from short circuits Fit a 30 mA differential protection device to protect people from electric shock caused by a possible break in the electrical insulation Place the cleaner power supply so that it is at a minimum distance of 3 5 meters from the pool edge The length of the standard cleaner cable is 15 24 meters GENERAL INFORMATION
10. dges back into the filter bucket assembly with the center frame reinforcements facing inward Snap the filter door latches into place Return the filter bucket assembly into the cleaner using the diagram shown to determine the front and back Close the dome and press the lid button to snap dome into place e Filter cleaning solution can be used to remove excessive dirt and or sand Remember The cleaner your filter is the more cleaning will be effective Periodic Cleaning of Moving Parts A WARNING Disconnect the power supply from electrical outlet before cleaning moving parts e Inspect the venturi to ensure that no debris or hair has clogged the impeller e The impeller can be cleaned by spraying it with a garden hose Remove any debris that has accumulated between the tracks and wheels Storage When out of the water store the cleaner in a dry shady location at temperatures between 4 C 46 C Cable Care With continued use the cable may become coiled like a telephone cord To correct this periodically stretching the cord out in the sun should remove any cord twists IMPORTANT The cable should be checked periodically for any external damage 11 Important Tips e Cleaning the filter cartridge after every use maximizes the unit s performance e Replace worn brushes e To avoid clogging the cleaner s filter elements be sure all chemical powders are fully dissolved before operating the cleaner e Ina pool with u
11. er is operating A WARNING To reduce the risk of injury do not let children use or play with pool cleaner Before installing the cleaner understand cleaner coverage The cleaner was not designed to automatically clean steps or to work under a solar cover It was also not designed to do initial cleanup for a new pool installation Operating the Cleaner N WARNING Your cleaner should not be used while people are swimming in the pool A a 30 mA differential protection device must be installed to protect your electrical outlet and to prevent any possible electric shock Failure to do so could create an electrical hazard which could result in death or serious injury to pool users or others due to electrical shock and may also cause damage to property DO NOT switch the pool cleaner to ON if it is not immersed in the water Operating the cleaner out of the water may cause severe damage and will result in loss of warranty Always remember to turn the power supply OFF and unplug it from the power outlet before removing the cleaner from the pool READ THESE IMPORTANT OPERATING TIPS BEFORE USING YOUR UNIT Dear AguaVac Owner Thank you for choosing AquaVac In order to achieve optimal performance please read and follow these steps 1 Allow the cleaner the first 10 minutes of each use to calculate pool size and configuration The normal programmed cycle is not designed to begin until after this period Cleaner filter
12. ill slowly sink to the bottom of the pool as the air inside is released 5 Connect the power supply to the protected outlet and switch it on The cleaner will perform a self diagnostics routine for several minutes before starting the cleaning cycle Caution DO NOT switch power supply ON when the cleaner is out of water This may result in damage to the pump and drive motor seals which will VOID the warranty 6 The cleaner will automatically shut off after a cleaning cycle of 2 hours If your pool is cleaned in less time than 2 hours you may shut the cleaner off manually by switching the power supply to the off position Should a second cleaning cycle be required switch OFF the power supply for 10 seconds and restart 7 After the pool has been cleaned switch OFF the power supply before removing the cleaner from the pool 8 Remove the cleaner from the water at the shallow end of the pool by pulling the cable until the cleaner reaches the surface Then lift it out of the water using the handle NOT the cable 9 If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Caution When pulling the cable reel it in hand over hand do NOT reel it around your arm DO NOT ENTER THE SWIMMING POOL WHEN THE CLEANER IS OPERATING Optimum operating water temperature range for the cleaner is 10 C 35 C Remove the cleaner from the pool after e
13. sable Pleated Element Cartridge Media Pleated Cellulose Polyester Blend Cleaning Routine Control Type Adaptive SeekControlLogic ASCL Microprocessor Drive System Direct Drive w Polyurethane Drive Track amp Acetal Stainless Steel Bearing System Input Primary Voltage OutputSecondaryVoltage Rated Output Current Weight 752 IMPORTANT SAFETY INSTRUCTIONS This robotic swimming pool cleaner has been manufactured with the highest degree of care and concern for safety We suggest the following safety precautions become part of your pool safety SAVE THESE INSTRUCTIONS ALWAYS PUT THE MACHINE INTO THE WATER BEFORE CONNECTING IT TO THE ELECTRICAL OUTLET IT IS IMPORTANT FOR SWIMMERS SAFETY TO REMOVE THE UNIT IMMEDIATELY FOLLOWING USE THIS CAN ALSO IMPROVE THE OPERATING LIFE OF YOUR CLEANER BE CERTAIN THE MACHINE IS ONLY PLUGGED INTO A PROTECTED 220 240 VOLT AC OUTLET THAT IS PROTECTED FROM SHORT CIRCUITS FIT A 30 MA DIFFERENTIAL PROTECTION DEVICE TO PROTECT PEOPLE FROM ELECTRIC SHOCK CAUSED BY A POSSIBLE BREAK IN THE ELECTRICAL INSULATION DO NOT HANDLE MACHINE WHILE IT IS PLUGGED INTO THE ELECTRICAL OUTLET DO NOT USE AN EXTENSION CORD THIS COULD CREATE A SAFETY HAZARD AND OR DAMAGE YOUR CLEANER ALWAYS STAY OUT OF THE POOL WHILE CLEANER IS IN OPERATION NEVER ALLOW PLUG TO ENTER THE POOL DO NOT OPERATE THE MACHINE OUT OF WATER THIS WILL DAMAGE THE MOTOR SEAL AND VOID THE WARRANTY DO NOT DRAG THE MACHINE OUT OF T
14. sually high calcium content more frequent cleaning of the filter is recommended e Save the original carton for extended storage or shipping requirements should your cleaner require dealer service e The sealed Motor Unit and the Power Supply contain no user serviceable parts Opening them will automatically VOID your warranty e Remove items such as thermometer toys and the like from the pool before operating the unit Such items can jam the cleaner and cause damage to the unit and or your pool Troubleshooting lf the cleaner fails to pick up fine or heavy debris e Clean the filter It may be clogged A filter cleaning solution can be used to remove excessive dirt and or sand If the cleaner starts working momentarily but then stops working e Impeller may be clogged or jammed with debris Check and clean if necessary following the instructions in the maintenance section e Brush roller or drive tracks are stuck Check for debris and clean if necessary e Cleaner performs by both timing and a pool wall detection sensor which ever comes first e There are 3 intake ports located at bottom of filter bucket and near the brush roller Intake ports located next to the roller help collect debris such as leaves and sand better than single intake e Fine debris such as sand may need a smaller intake port for stronger suction The cleaner can create a stronger suction with a high velocity flapper that can be installed at intake port
15. ting caught on drains floor cleaning heads or toys The user may try starting the cleaner in different locations to find the optimum cleaning location If debris falls from cleaner while removing from pool it may be caused by filter overload increase frequency of filter cleaning Assure that there is no large debris blocking any of the three intakes Large debris must be removed from the pool before using machine If drain flaps are out of place or stuck by sand or leaves in the open position the flaps can be snapped back into place after cleaning the area Avoid dropping or throwing machine into pool Place cleaner away from the pool wall but do not throw the cleaner in the pool If the flotation cord gets twisted which can be caused by the cleaner getting stuck on large objects such as rocks toys or main drains it can be straightened by laying the flotation cord at full length if possible in the sun heat from the sun will help reduce the twisting If a high level of debris is visible through the dome windows remove cleaner quickly from the water to reduce the chance of the debris escaping the filter bucket and re entering the pool 13 Specifications Weight w o cable Speed rpm 55 Voltage Current amp Waterproof Sealing Double Redundant Radial Shaft Seals amp O ring Motor Housing Sealed Watertight High Impact Polypropylene Overload Protection Electronic Overload Monitoring with auto shutoff Type Removable Re U
Download Pdf Manuals
Related Search