GALAXYTM Series Automatic Hand Dryer Operating Instructions for
Contents
1. WARNING AS WITH ANY ELECTRIC APPLIANCE FAILURE TO FIG 3 ELECTRICALLY GROUND UNIT MAY RESULT IN SERIOUS INJURY OR DEATH 10 Reinstall front cover push up locking bolt and reinstall the three screws that were removed earlier 206 240V 60H2 bi 1 Fan M Technical Data 3 Heating element 3 Sensor GALAXY 1 120V 60 Heriz 1850 Watts a Heating element 1800 Watts motor 50 W GALAXY 2 At 240V 60 Hertz 2000 Watts Heating element 1950 Watts motor 50 W Se ee At 208V 60 Hertz 1500 Watts Heating element 1450 Watts motor 50 W 3 LITE For dimensions see figure 3 The weight of the unit without shipping materials is 5 5 Ibs 2 5 kg 2 GALAXY with Metal Housing Installation Instructions for the Licensed Installer DO NOT INSTALL UNIT WHERE IT CAN ACCIDENTALLY BE SPLASHED WITH WATER ELECTRIC SHOCK MAY RESULT WARNING BEFORE BEGINNING ANY WORK ON THE ELECTRIC INSTALLATION BE SURE THE MAIN BREAKER PANEL SWITCH IS OFF TO AVOID ANY DANGER OF ELECTRIC SHOCK NOTE THE CIRCUIT SHOULD BE EQUIPPED WITH A GROUND FAULT INTERRUPTER WHERE REQUIRED BY iss LOCAL STATE OR NATIONAL ELECTRICAL CODES FIG 4 1 All electrical work must comply with national and 6 7 8 175 mm applicable state and local electrical codes 2 The GALAXY hand dryer must have its own independent circuit using cable of the appropriate size ae2. STIEBEL ELTRON GALAXY Series Automatic Hand Dryer Y Q Operating Instructions for the User amp Installation Instructions for the Licensed Installer THIS MANUAL MUST BE READ CAREFULLY BEFORE ATTEMPTING TO INSTALL THE GALAXY AUTOMATIC HAND DRYER IF YOU DO NOT FOLLOW THE SAFETY RULES OR THE INSTRUCTIONS OUTLINED IN THIS MANUAL THE UNIT MAY NOT OPERATE PROPERLY AND IT COULD CAUSE PROPERTY DAMAGE SERIOUS BODILY INJURY AND OR DEATH STIEBEL ELTRON INC WILL NOT BE LIABLE FOR ANY DAMAGES BECAUSE OF FAILURE TO COMPLY WITH THE INSTALLATION AND OPERATING INSTRUCTIONS OUTLINED IN THIS MANUAL OR BECAUSE OF IMPROPER USE FAILURE TO COMPLY WITH THE INSTALLATION AND OPERATING INSTRUCTIONS OR IMPROPER USE VOIDS WARRANTY NEVER REMOVE THE UNIT S COVER UNLESS THE ELECTRICITY IS TURNED OFF MAKE SURE THAT AIR INLET AND AIR EXIT GRILLS ARE ALWAYS KEPT FREE TO ENSURE PROPER AIR FLOW IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION OR OPERATION OF THIS HAND DRYER OR IF YOU NEED A COPY OF THE INSTALLATION INSTRUCTIONS PLEASE CALL OUR TECHNICAL SERVICE LINE AT 1 800 582 8423 LIMITED WARRANTY STIEBEL ELTRON Inc warrants to the original owner that the GALAXY hand dryer will be free from defects in workmanship and materials for a period of FIVE YEARS from the date of purchase Should any part s prove to be defective under normal use during this period STIEBEL ELTRON Inc will be responsible for replacement of the def
3. 1800 Watts motor 50 W GALAXY 2 At 240V 60 Hertz 2000 Watts Jo E Lee Heating element 1950 Watts motor 50 W Ca At 208V 60 Hertz 1500 Watts Heating element 1450 Watts motor 50 W For dimensions see figure 3 The weight of the unit without shipping 2 materials is 8 8 Ibs 4 kg ETICDE CIFBDAAI SIEBELELTRON Inc 17 West Street o West Hatfield MA 01088 STIEBEL ELTRON Phone 413 247 3380 or 800 582 8423 e Fax 413 247 3369 Drilling template for hand dryer TM mounting Galaxy sa oy Suip 340439 sjuawainseaw jsulese g L 9 s joy Sununow jo u01 Zi 230 YIBY ZIS 3991109 ye ulud you Aew zejdw L s joy SUIJUNOW y e CE 6
4. by a correctly rated circuit breaker The GALAXY 1 unit for 110 120V requires a 20 amp circuit breaker and a gauge 12 copper wire The GALAXY 2 unit for 220 240V or 208V requires a 15 amp circuit breaker and a gauge 12 copper wire 3 Install unit so that the bottom is Sep tay 48 above floor Unit should be at least 4 from a perpendicular wall FIG 1 on page 2 4 Transfer the four mounting points to the wall by using the enclosed drilling template and drill mounting holes 5 Remove one screw on the locking bolt FIG 4 6 Pull down locking bolt Remove housing FIG 4 7 Install a 1 2 electrical connector in the back part of housing in the hole located below the wiring block 6 7 8 175mm 10 1 2 266 mm 8 Feed wires through connector tighten clamp down on wire Mount back part of housing to the wall A 9 The live wires must be connected to the slots on the terminal marked N L and L Ground wire must be connected to the wire terminal on the blower housing 9 1 16 230 mm with the ground symbol ie FIG 5 WARNING AS WITH ANY ELECTRIC APPLIANCE FAILURE TO ELECTRICALLY GROUND UNIT MAY RESULT IN SERIOUS INJURY OR DEATH 10 Reinstall front cover push up locking bolt and J cro reinstall the screw that was removed earlier 1 Fan Motor 2 Heating Element Technical Data 3 Sensor GALAXY 1 120V 60 Hertz 1850 Watts Heating element
5. ective part s only Damage to the housing due to abuse is not covered by this warranty STIEBEL ELTRON Inc is not responsible for labor charges to remove and or replace the defective part s or any incidental or consequential expenses Should the owner wish to return the entire unit for repair the owner must first secure written authorization from STIEBEL ELTRON Inc The owner shall be required to show proof of purchase date by including a copy of the original invoice and to pay all transportation costs to return defective part s or hand dryer for repair or replacement IF YOU NEED TO RETURN A PART OR A HAND DRYER UNDER WARRANTY PLEASE CALL US FIRST TO OBTAIN SHIPPING INSTRUCTIONS REMEMBER TO SEND A COPY OF THE INVOICE WITH YOUR RETURNED PART STIEBEL ELTRON Inc 17 West Street West Hatfield MA 01088 Phone 800 582 8423 min 4 10 cm Operating Instructions for the user In order to dry your hands most efficiently please use the following procedure e shake off excess water over the wash basin A e place hands underneath the unit at a distance of 4 7 e rub your hands together as if you were washing them Your hands will be dry within 25 35 seconds Tai The STIEBEL ELTRON GALAXY series hand dryers are equipped with an infrared sensor switch This sensor will activate the unit when hands are placed underneath it Approximately 7 seconds after the hands have been removed the unit will automatica
6. l electrical work must comply with national and a IN FIG 2 applicable state and local electrical codes 2 The GALAXY hand dryer must have its own 6 7 8 175 mm independent circuit using 3 wire cable of the appropriate size protected by a correctly rated double pole circuit breaker The GALAXY 1 unit for 110 120V requires a 20 amp circuit breaker and a gauge 12 copper wire The GALAXY 2 unit for 220 240V or 208V requires a 15 amp circuit breaker and a gauge 12 copper wire 3 Install unit so that the bottom is approximately 48 above a floor Unit should be at least 4 from a perpendicular wall NA FIG 1 previous page 4 Transfer the four mounting points to the wall by using the enclosed drilling template and drill mounting holes 5 Remove the two screws at the air outlet grill and the screw on the locking bolt FIG 2 6 oo locking bolt Remove front part of housing FIG 7 Install a 1 2 electrical connector in the back part of housing in the hole located below the wiring block 9 7 8 250 mm 8 Feed wires through connector tighten clamp down on wire Mount back part of housing to the wall 6 7 8 175 mm 9 The live wires must be connected to the slots on the terminal marked N L and L Ground wire must be connected to the wire terminal on the blower housing with the ground symbol 9 4 16 230 mm
7. lly shut off The sensor is the black rectangle located underneath the unit between the air exit and air inlet grills The sensor switch will not work properly if it has been covered by gum or dirt If the sensor isobstructed the hand dryer will switch off automatically to prevent it from running continuously Should the unit overheat a safety high limit switch will turn off the heating element The safety high limit switch resets automatically once the heating element has had a chance to cool down Normal Care To clean the case use a soft cloth with a mild detergent if necessary Never use any abrasive cleaners since they will scratch the finish of the unit Never spray water or cleaning fluids directly on hand dryer While cleaning the unit make sure the electric eye switch is not covered THE GALAXY HAND DRYER DOES NOT CONTAIN ANY PARTS SERVICEABLE BY THE LAY PERSON IN CASE OF MALFUNTION PLEASE CONTACT A LICENSED ELECTRICIAN FIG 1 GALAXY with Plastic Housing Installation Instructions for the Licensed Installer DO NOT INSTALL UNIT WHERE IT CAN ACCIDENTALLY BE SPLASHED WITH WATER ELECTRIC SHOCK MAY RESULT WARNING BEFORE BEGINNING ANY WORK ON THE ELECTRIC INSTALLATION BE SURE THE MAIN BREAKER PANEL SWITCH IS OFF TO AVOID ANY DANGER OF ELECTRIC SHOCK NOTE THE CIRCUIT SHOULD BE EQUIPPED WITH A GROUND FAULT INTERRUPTER WHERE REQUIRED BY LOCAL STATE OR NATIONAL ELECTRICAL CODES 1 Al
Download Pdf Manuals
Related Search