Home

Installation Manual

1. SENS OK WRONG 1 Check that the sensor is level from side to side and pointed at the area you desire If unit is tilted part of the detection zone may be high in the air over people s heads Solution Position sensor exactly level from side to side 2 Check that the sensor is not mount ed too high If mounted above 20 feet much of the usable range will be lost Solution Mounting at 6 feet to 10 feet allows maximum range 3 Check that movement is not directly towards sensor Sensor will see movement across its pattern more quickly To fix move the sensor 4 Check that movement far away and directly towards sensor is not entirely within one zone Problem Sensor will not detect until movement crosses zones Solution Micro Adjust sensor by moving sideways 1 4 This may move the zones to allow earlier detection Technical Tips Range Appears Limited 20 40 Reduced Range 6 10 60 Maximum Range No detection until here Detection here now Less Sensitive More Sensitive 20 19 1 V rifier que le d tecteur est de niveau de gauche droite et point e en direction de la zone voulue Si l unit est inclin e une partie de la zone de d tection peut tre relev e au dessus de la t te des gens Solution Mettre le d tecteur parfaite ment de niveau de gauche droite 2 V rifier que le d tecteur n est pas install trop haut S il est install
2. plus de 20 pieds une grande partie de la port e utile est perdue Solution Installer entre 6 pieds et 10 pieds pour obtenir une port e maximale 3 V rifier que le mouvement n est pas dirig directement vers le d tecteur Le d tecteur verra le mouvement plus rapidement sur toute sa zone Pour corriger d placer le d tecteur 4 V rifier que le mouvement loign et directement en direc tion du d tecteur ne se trouve pas compl tement l int rieur d une zone Probl me Le d tecteur ne d tectera pas tant que le mouvement ne traversera pas les zones Solution Micro ajuster le d tecteur en le d pla ant gauche ou droite sur 1 4 po Ce faible ajustement peut d placer les zones de mani re permettre la d tection plus rapide Technical Tips Lights Turn Off Too Quickly 1 Check if sensor is being tricked by reflected light If lights controlled by the sensor shine or reflect into the photocell locat ed behind the lens the unit will go on briefly see its own light and turn off thinking that it is daytime Problems Lights reflect into photocell Lights shine directly into photocell Solution Adjust SUN MOON knob slightly clockwise to allow operation at higher ambient light levels Alternatively move the lights or reflectors or mask the lens in the direction of the lights and or reflections 2 Check if R lamps non reflector A lamps or self balla
3. Technical Tips Lights Do Not Turn On 20 safety zone TIME 12 MINS SENS TIME 12 MINS SENS 18 17 WRONG OK MINUTERIE SENSIBILIT 1 Make sure the sensor is installed on its own dedicated circuit free of motor loads such as HVAC equipment kitchen appliances or garage door openers 2 It is not recommended to wire sensors in parallel More than one sensor wired together makes them difficult to troubleshoot Disconnect multi ple sensors and test separately 3 Keep all people completely out of the detection pattern to make sure the sensor is not detecting them 4 Make sure sensor is located below and as far as possible from its lights Heat from the lights may trigger the sensor Solution Move sensor below and away from the lights 5 Make sure lights are not reflecting back into sensor Check for white or reflective surfaces close to the sensor Solution Aim sensor away from reflective objects or move the objects and lower sensitivity 6 Make sure sensor is not aimed within 20 feet of a road or sidewalk Passing cars will activate sensor Solution A 20 foot safety zone and reduced sensitivity are recommended to avoid activation from passing cars 7 Heavy rain snow or high winds may activate the sensor occasionally Reduce sensitivity control slightly until problem stops 8 Moths can be attracted to the lights and fly close to the sensor causing triggering Reducing the
4. plus superb 360 detection below and to all sides How do the scanning LED detection indicators work Scanning LEDs serve as a deterrent by indicating a securi ty device in operation They also show the STL360 s mode of operation On Guard When the STL360 is On Guard in Auto mode three red LEDs scan continu ously day and night except during detections at which time the controlled lights will go on Test Mode When the sensor is in Test Mode all the LEDs will be off If the sensor is set for night only operation the LED stays On Guard daytime detections do not turn on the lights Manual Override Mode In Manual Override Mode the middle LED will be on see page 14 Howhe SuperSTL360 360 Work How Does the Super Stealth 360 Work How long do the lights stay on Lights remain on as long as there is movement within the protection zone Once the zone is vacated lights can be adjusted to remain on from approximately 5 seconds up to 12 minutes Since the lights are on only when needed and the sensor uses only one watt the STL360 is extremely energy efficient Can lights still be turned on with the light switch Yes STL360 can be controlled by a conventional indoor switch or circuit breaker The STL360 operates in Auto Mode unless changed The light can be turned on or off manually at night only see pages 13 14 for more info Manual Override Mode to keep lights on Flip the switch
5. 7 Heavy rain snow or high winds may activate the sensor occasionally Reduce sensitivity control slightly until problem stops 8 Moths can be attracted to the lights and fly close to the sensor causing triggering Reducing the sensitivity may help 9 Check Solutions 3 4 5 6 7 and 8 under If Lights Do Not Turn Off Technical Tips Lights Turn On and Off Inappropriately 1 Check that lamps and fixtures work Compare wiring to the wiring diagram in this manual Check that the power is on 2 If installing during daylight remember that the sensor will provide 2 minutes of Test Time after power is turned on After 2 minutes the sensor will switch to Automatic Mode and will not work during day light if the photocell control is turned to the night only position moon symbol If you require 2 more minutes of Test Time turn the power off for at least 10 seconds and back on again If you require the sensor to operate both day and night turn the SUN MOON control knob clockwise to the sun and moon symbol 3 Check that lights from another source such as adjacent porch lights garden lights or street lights are not in the sensor s view The sen sor s photocell may detect the light and deactivate daylight If you desire the sensor to operate in higher ambient light levels turn the SUN MOON control knob counter clockwise toward the sun symbol 4 Was sensor wired hot If so circuitry may have been damaged
6. high the usable range is reduced Location Tips Difficult Locations Sensor may be triggered by unwanted movement or heat source such as a swaying tree road traffic dryer vent swimming pool or hot tub To Improve Performance in Difficult Locations Reduce sensitivity by turning the SENS knob counterclockwise and or Mask lens in the direction of the unwanted movement or heat source using the lens mask provided or opaque tape Mounting Stability Mount sensor on stable surface Do not mount on a tree or pole that will move in the wind Make sure sensor and lights are mounted firmly If they move when touched tighten all screws Light vs Sensor Position Make sure heat from lights is not triggering sensor Sensor must be located below and as far away as possible from its lights STL360Q1 STL360Q2 amp STL360Q3 Kits Mount only on non combustible surfaces Side View 6 10 wrong wrong OK TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 20 40 6 10 60 Reduced Range Maximum Range mask 4 3 60 60 20 Hauteur de fixation Installer entre 6 et 12 pi au dessus du sol pour obtenir une port e maximale Si le d tecteur est install plus de 15 pi de hauteur la port e utile est r duite Vue lat rale 6 10 pi 20 pi 60 pi 60 pi Port e maximale Port e r duite 6 10 pi 60 pi 20 pi
7. In Test Mode no LEDs are lit MANUAL OVERRIDE MODE The STL360 has a protected Manual Override that requires a double flip of the light switch so momentary power problems do not interfere with normal sensor operation By flipping the switch that operates the sensor twice off on off on within 2 seconds you will override the sensor to keep lights on continuously until dawn If you set the Manual Override Mode during daylight the sensor will be prepared to turn on at dusk and remain on until dawn This is a handy feature if you leave home for the day and you want the lights on to greet you when you return When the sensor is in Ready for Manual Override Mode the middle LED will be on TO RESUME AUTOMATIC MODE Switch OFF the power for at least 10 seconds then turn it ON again Sensor will reset to Automatic Mode after completing the warm up period and Test Mode 14 On Guard Auto Mode LEDs scan continuously back and forth Ready for Manual Override Mode Middle LED on Ready for Evening Timer Mode Middle LED blinks 13 DAYTIME 24 HOUR OPERATION OF MANUAL OVERRIDE If you set Manual Override while set to 24 hour operation lights will come on and remain on continuosly Lights will not turn off at dawn Pr t pour le mode contournement manuel D L du centre allum e Walk Testing STL360 s full coverage pattern reduces the need for aiming and adjustment The purpose of the Walk Tes
8. Le r glage de l usine est 100 Adjusting the Settings TIME Sets the time that lights will remain on after the detection zone is vacated Adjustable from approximately 5 seconds to 12 minutes The Factory Setting is 12 minutes PHOTOCELL For night only operation turn the knob completely counterclockwise to to the MOON symbol For 24 hour operation turn the knob all the way clockwise to the MOON SUN symbol Adjust counterclockwise to have the sensor come on later at dusk clockwise to have it come on earlier The Factory Setting is Night only MOON If you set Evening Timer while set to 24 hour operation Evening Timer will begin immediately after flipping switch SENSITIVITY Increases or decreases the responsiveness and range of the sensor adjustable from 30 to 100 The Factory Setting is 100 Adjusting the Settings EVENING TIMER The STL360 provides an alternative to normal motion activated lighting The EVENING TIMER can keep lights on continuously without motion for 1 to 8 hours after dusk This is great for evening activities requiring continuous light During vacations the EVENING TIMER provides a lived in look by simulating an occupant turning lights on at dusk and then off at bedtime To set the EVENING TIMER flip the wall switch controlling the sensor three times slowly off on off on off on within 3 seconds If you set the EVENING TIMER during daytime the middle LED should start blinking
9. lived in look by simulating an occupant turning lights on at dusk and then off at bedtime To set the EVENING TIMER flip the wall switch controlling the sensor three times slowly off on off on off on within 3 seconds If you set the EVENING TIMER during daytime the middle LED should start blinking indicating that the Evening Timer will start when dusk is detected Choose the length of time you want continuous lighting For example if you set the EVENING TIMER to 8 the sensor will keep lights ON continuously for 8 hours after dusk Once 8 hours have passed the sensor will revert to motion activated mode At dawn the photocell will detect light and prevent lights from turning on during the daytime If you do not want to use the EVENING TIMER do NOT flip the switch 3 times as described above To end use of the EVENING TIMER switch OFF the power for at least 10 seconds then ON again Sensor will be in Automatic Mode After completing the warm up period You can affix this label right provided to your indoor light switch plate for easy reference 12 TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 11 Accro t ou r duit la r action et la port e du d tecteur r glage de 30 100
10. n e une partie de la zone de d tection peut tre relev e au dessus de la t te des gens Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier
11. 40 pi Endroits difficiles Le d tecteur peut tre d clench par un mouvement non d sir ou une source de chaleur comme un arbre qui bouge la circulation routi re une bouche de s ch euse une piscine ou un bain tourbillon Pour am liorer le rendement dans les endroits difficiles R duire la sensibilit en tournant le bouton SENS vers la gauche et ou Masquer la lentille en direction du mouve ment non d sir ou la source de chaleur l aide du masque de lentille fourni ou de ruban opaque Stabilit de l installation Installer le d tecteur sur une surface stable Ne pas installer sur un arbre ou un poteau qui bougera au vent S assurer que le d tecteur et les luminaires sont solidement install s S ils bougent au toucher serrer toutes les vis Position des luminaires par rapport au d tecteur S assurer que la chaleur d gag e par les luminaires ne d clenche pas le d tecteur Le d tecteur doit tre plac sous et aussi loin que possible des luminaires Trousses STL360Q1 STL360Q2 et STL360Q3 Installer seulement sur des surfaces ininflam mables Choosing a Location The best location is where the sensor can see all paths of movement The sensor may be wall or soffit mounted As distance from the sensor increases larger movement will be required for detection For instance at 10 feet a half step will be enough while at 50 feet several steps will be necessary
12. NJ 07647 The STL360 should be packed carefully Please include your sales receipt and a description of the problem If your unit is out of warranty or the damage is unrelated to the original manufacture return your unit directly to us with a check for 20 00 made out to RAB Electric We will repair or replace your unit Under no circumstances shall we be liable for any incidental or consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property or revenue or cost of installation removal or re installation This warranty gives you specific legal rights and you may also have other rights which vary from state to state Contents of Accessory Kit 2 Lens Masks Indoor Switchplate Label 3 Wire Nuts Adjustment Tool Mylar Lens Mask Crossbar with Green Ground Screw Hanging Hook 1 2 Close Up Plugs 3 Slotted Screws 4 Finishing Cap O ring Gasket Center Mounting Screw Foam Gaskets 2 Metal Plate MAKES IT EASY Easy Installation amp Product Help Toll Free Phone Toll Free Fax Fax on Demand Call our friendly experts Send faxes to RAB Faxed information 8AM 6PM ET Mon Fri 24 7 24 7 888 RAB 1000 888 RAB 1232 888 RAB 1236 E mail www rabweb com Questions and requests Visit our internet site answered promptly for product information tech rabweb com RAB L
13. Protection Pattern 180 forward 360 below and to all sides Time Adjustment 5 seconds to 12 minutes Power Consumption 1 watt Surge protection 6000 volts Cautions TURN OFF ALL POWER AT CIRCUIT BREAKER FUSE PANEL Read entire Installation Manual before proceeding All wiring should comply with local electrical codes and requires a qualified electrician The total lighting load connected to STL360 must not exceed 1000 watts incandescent or quartz 250 watts fluorescent To switch more wattage an electrician can install a relay Line Carrier Remote Control Systems such as X 10 Leviton or Radio Shack are incompatible with sensors and may cause false activations Do not install sensors on a circuit that feeds motor loads such as kitchen appliances HVAC equipment washer dryer or garage door openers Sensor functions best when the direction of expected movement is across its detection pattern not towards the sensor Mount 6 12 high for optimum range and detection The STEALTH360 is the most reliable and technically advanced motion activated light control ever produced This techni cal manual is written for electrical professionals who wish to maximize the performance and reliability of this superb sensor RAB welcomes your questions or comments Please call 888 722 1000 or email tech rabweb com Thank you for purchasing a RAB sensor STL360H STL360HBW STL360Q1 STL360Q3W STL360Q2W Installat
14. indicating that the Evening Timer will start when dusk is detected Choose the length of time you want continuous lighting For example if you set the EVENING TIMER to 8 the sensor will keep lights ON continuously for 8 hours after dusk Once 8 hours have passed the sensor will revert to motion activated mode At dawn the photocell will detect light and prevent lights from turning on during the daytime If you do not want to use the EVENING TIMER do NOT flip the switch 3 times as described above To end use of the EVENING TIMER switch OFF the power for at least 10 seconds then ON again Sensor will be in Automatic Mode After completing the warm up period You can affix this label right provided to your indoor light switch plate for easy reference 12 TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 11 Pour le fonctionnement la nuit seulement tourner le bou ton compl tement gauche symbole de LUNE Pour le fonctionnement 24 heures tourner le bouton compl te ment droite au symbole de LUNE SOLEIL R gler gauche pour que le d tecteur fonctionne plus tard au cr puscule et droite pour qu il fonctionne plus t t Le r glage de l usine est Nuit seulement LUNE Si elle es
15. t raccord sous tension Si c est le cas les circuits peuvent avoir t endommag s 7 S assurer que le d tecteur n est pas point moins de 20 pieds d une route Probl me Les voitures d clenchent le d tecteur Solution On recommande une zone de s curit de 20 pieds et de r duire la sensibilit pour viter que les voitures ne d clenchent le d tecteur 8 S assurer que la chaleur d gag e par les luminaires ne d clenche pas le d tecteur S assurer que le d tecteur est install en dessous et aussi loin que possible des luminaires Walk Testing STL360 s full coverage pattern reduces the need for aiming and adjustment The purpose of the Walk Test is to check and adjust the coverage pattern The STL360 has a Test Period which allows the sensor to be walk tested day or night To enter Test Mode The sensor is in Test Mode when power is first applied Turn power off for at least 10 seconds and back on 1 Aim the sensor at the traffic pattern you want to detect Sensor will detect any movement ACROSS its pattern most effectively 2 Start outside the pattern and walk across the pattern until the lights go on As distance from the sensor increases it will take more movement to be detected 3 Adjust sensor aiming as necessary to improve coverage Make sure sensor is level 4 Sensitivity may be decreased with the SENS knob to detect a limited area or if the sensor is being activated b
16. utiliser des projecteurs PAR ou des projecteurs au quartz pour que le fonctionnement du d tec teur ne soit pas perturb par la lumi re directe Si on utilise des projecteurs PAR on recommande d utiliser des lampes conomes d nergie plus basse puissance Technical Tips Lights Turn Off Too Quickly 1 Check if sensor is being tricked by reflected light If lights controlled by the sensor shine or reflect into the photocell locat ed behind the lens the unit will go on briefly see its own light and turn off thinking that it is daytime Problems Lights reflect into photocell Lights shine directly into photocell Solution Adjust SUN MOON knob slightly clockwise to allow operation at higher ambient light levels Alternatively move the lights or reflectors or mask the lens in the direction of the lights and or reflections 2 Check if R lamps non reflector A lamps or self ballasted PL lamps are being used in a non enclosed lampholder If so switch to reflector PAR floodlight lamps or Quartz floods so the sensor is not affected by stray light If using PAR floodlights con sider using lower wattage energy saving lamps TIME 12 MINS SENS OK WRONG 1 Check that the sensor is level from side to side and pointed at the area you desire If unit is tilted part of the detection zone may be high in the air over people s heads Solution Position sensor exactly level from s
17. will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 STL360 Kit Assembly and Wiring STL360 floodlight kits come pre wired and assembled on the RC CU4 EZ plate allowing for mounting on round rectangular or octagonal surface or recessed boxes Mounting Wiring STL360 Kit Assembly and Wiring 1 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 2 Easy Wiring Tip Use the S shaped Hands Free Hangin
18. 2 minutes then it will switch to Auto Mode with lights off and ready to detect movement 2 Make sure that the sensor is not in Evening Timer Mode Turn power OFF for 10 seconds see 1 3 Make sure sensor is not aimed at or mounted over something that would move or change temperature such as waving branches water air condi tioners windows or heating vents even on neighboring property You can test for infrared sources in the area by placing a box or bag over the sensor Put sensor into test mode Lights should stay off Wave your hand inside bag in front of sensor Lights should go on and then time out If sensor operates properly when covered check items 4 8 Problem Sensor is triggered by unwanted movement or heat source Solution 1 Aim sensor away from movement or 2 Mask lens as in the direction of the source 3 Lower sensitivity control setting 4 Make sure sensor and lights are mounted firmly and do not move even slightly when touched If they move tighten all screws 5 Make sure sensor is not mounted on an unstable object such as a tree or pole that will move in the wind Problem Movement of tree triggers sensor Solution Mount on stable surface 6 Was sensor wired hot If so circuitry may have been damaged 7 Make sure sensor is not aimed within 20 feet of a road Problem Passing cars activate sensor Solution A 20 foot safety zone and lower sensitivity are recommended to avoid activation f
19. D L du centre clignote 3 fois fait une pause et recommence Programmer la minuterie de soir e en actionnant l interrupteur qui commande le d tecteur 3 fois en 3 secondes arr t marche arr t marche arr t marche MODE TEST Pour passer en mode test couper le courant pendant 10 secondes puis le r tablir Le mode test se met en marche apr s la p riode d chauffement de 30 secondes Pendant la p riode d chauffement les luminaires restent allum s en permanence et les D L sont teintes Pendant la p riode de test le d tecteur allume les luminaires pendant 3 secondes chaque fois qu il d tecte un objet dans sa zone de d tection Le d tecteur retourne en mode automatique apr s le mode test de 2 minutes Cependant si on teste en permanence le d tecteur demeure en mode test Pour interrompre le mode test il faut quitter la zone de d tection pendant 1 minute ou plus Les D L d exploration s allument quand le mode test est interrompu Sensor Modes AUTOMATIC MODE Lights will turn on when there is movement with in the detection zone after dusk EVENING TIMER MODE Keeps lights on for 1 8 hours after dusk Sensor then reverts to Automatic Mode until dawn If you set the Evening Timer Mode during daylight the sensor will be prepared to turn on at dusk and remain on for the number of hours you set When the sensor is in Ready for Evening Timer Mode the middle LED will blink 3 times pause
20. and repeat Set the Evening Timer by flipping the switch that operates the sensor 3 times within 3 seconds off on off on off on TEST MODE To enter Test Mode turn power off for 10 seconds then back on There is a 30 second warm up period then the Test Mode starts During the warm up the lights stay on continiously and LEDs are off During the Test Period the sensor will keep lights on for 3 seconds each time it detects movement in its detection zone The sensor will revert back to Automatic Mode after 2 minutes of Test Mode However if you keep testing continuously the sensor will stay in Test Mode To end Test Mode you must vacate the detection zone for 1 minute or more Scanning LEDs will appear when test mode ends If you require 2 more minutes of Test Mode turn the power off for at least 10 seconds and back on again In Test Mode no LEDs are lit MANUAL OVERRIDE MODE The STL360 has a protected Manual Override that requires a double flip of the light switch so momentary power problems do not interfere with normal sensor operation By flipping the switch that operates the sensor twice off on off on within 2 seconds you will override the sensor to keep lights on continuously until dawn If you set the Manual Override Mode during daylight the sensor will be prepared to turn on at dusk and remain on until dawn This is a handy feature if you leave home for the day and you want the lights on to greet you wh
21. fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 Masquer la lentille en direction de la circula tion l aide du masque de lentille fourni ou de ruban opaque On peut briser le masque de lentille le long des lignes pour obtenir la dimension voulue S assurer que le d tecteur n est pas orient vers la circulation Le d tecteur doit tre dirig vers le bas pour que la port e maximale du d tect eur se termine au moins 20 pi de la route On vitera ainsi de d tecter les camions et voitures qui circulent ou les courants d air qu ils produ isent Installation de niveau Le d tecteur doit tre install de niveau de gauche droite et point en direction de la zone prot ger Si l unit est incli
22. for detection How large an area does STL360 protect Two powerful detectors combine to give the STL360 180 x 60 long forward range plus superb 360 downward detection below and to all sides Mounting Height Mounting at 6 12 above the ground allows maximum range If the sensor is mounted above 15 high the usable range is reduced Location Tips Difficult Locations Sensor may be triggered by unwanted movement or heat source such as a swaying tree road traffic dryer vent swimming pool or hot tub To Improve Performance in Difficult Locations Reduce sensitivity by turning the SENS knob counterclockwise and or Mask lens in the direction of the unwanted movement or heat source using the lens mask provided or opaque tape Mounting Stability Mount sensor on stable surface Do not mount on a tree or pole that will move in the wind Make sure sensor and lights are mounted firmly If they move when touched tighten all screws Light vs Sensor Position Make sure heat from lights is not triggering sensor Sensor must be located below and as far away as possible from its lights STL360Q1 STL360Q2 amp STL360Q3 Kits Mount only on non combustible surfaces Side View 6 10 wrong wrong OK TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 20 40 6 10 60 Reduced Range Maximum Range mask 4 3 60 60 20 Choo
23. ground wire s to junction box grounding screw 7 Position EZ Plate gaskets and metal plate see pg 7 8 Strip 1 2 of insulation from all leads Connect as shown in wiring diagram 9 Twist on wire nuts Secure with electrical tape 10 Make sure all unused openings in EZ Plate are closed with plugs provided 11 Screw in light bulbs Turn on power 12 Conduct Walk Test to adjust sensor response see page 15 STL360 Assembly and Wiring Multiple Sensors Multiple sensors may be wired together but doing this will make problems difficult to troubleshoot Single sensors that control their own lights will give a more accurate location of movement and trouble free operation Multiple Fixtures Multiple fixtures may be wired to a single sensor To handle loads greater than 1 000 watts a qualified electrician should install a relay Power Quality It is not recommended to install sensors on a circuit that also feeds motor loads such as HVAC equipment kitchen appliances or garage door openers The Stealth circuit is surge and transient protected to IEC specifications However if voltage varies significantly from 120 volts which may occur on circuits with motor loads the sensor may malfunction 10 Power In White Red Black Power In White Sensor Red Black 9 Black Blanc Noir Rouge Noir Entr e lectrique STL360 Assembly and Wiring To install a STL360 Sensor with separate
24. lamps or self ballasted PL lamps are being used in a non enclosed lampholder If so switch to reflector PAR floodlight lamps or Quartz floods so the sensor is not affected by stray light If using PAR floodlights con sider using lower wattage energy saving lamps TIME 12 MINS SENS OK WRONG 1 Check that the sensor is level from side to side and pointed at the area you desire If unit is tilted part of the detection zone may be high in the air over people s heads Solution Position sensor exactly level from side to side 2 Check that the sensor is not mount ed too high If mounted above 20 feet much of the usable range will be lost Solution Mounting at 6 feet to 10 feet allows maximum range 3 Check that movement is not directly towards sensor Sensor will see movement across its pattern more quickly To fix move the sensor 4 Check that movement far away and directly towards sensor is not entirely within one zone Problem Sensor will not detect until movement crosses zones Solution Micro Adjust sensor by moving sideways 1 4 This may move the zones to allow earlier detection Technical Tips Range Appears Limited 20 40 Reduced Range 6 10 60 Maximum Range No detection until here Detection here now Less Sensitive More Sensitive 20 19 MINUTERIE SENSIBILIT Technical Tips Lights Turn Off Too Quickly 1 Check if sensor is being tric
25. minutes of Test Mode However if you keep testing continuously the sensor will stay in Test Mode To end Test Mode you must vacate the detection zone for 1 minute or more Scanning LEDs will appear when test mode ends If you require 2 more minutes of Test Mode turn the power off for at least 10 seconds and back on again In Test Mode no LEDs are lit MANUAL OVERRIDE MODE The STL360 has a protected Manual Override that requires a double flip of the light switch so momentary power problems do not interfere with normal sensor operation By flipping the switch that operates the sensor twice off on off on within 2 seconds you will override the sensor to keep lights on continuously until dawn If you set the Manual Override Mode during daylight the sensor will be prepared to turn on at dusk and remain on until dawn This is a handy feature if you leave home for the day and you want the lights on to greet you when you return When the sensor is in Ready for Manual Override Mode the middle LED will be on TO RESUME AUTOMATIC MODE Switch OFF the power for at least 10 seconds then turn it ON again Sensor will reset to Automatic Mode after completing the warm up period and Test Mode 14 On Guard Auto Mode LEDs scan continuously back and forth Ready for Manual Override Mode Middle LED on Ready for Evening Timer Mode Middle LED blinks 13 DAYTIME 24 HOUR OPERATION OF MANUAL OVERRIDE If
26. more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 Meilleure d tection apr s un micro ajustement VOIE D ACC S VOIE D ACC S 1 Fixer la barre de montage universelle au moyen des vis de barre fournies la bo te de jonction Si on fixe la trousse STL360 une bo te murale r sistant aux intemp ries on doit utiliser les deux joints et placer la plaque de montage de m tal entre les deux 2 Conseil de raccorde ment simple Utiliser le crochet de fixation en S mains libres pour retenir la plaque EZ pendant le raccordement 3 Acheminer les conduc teurs d alimentation et les conduc
27. move the objects and lower sensitivity 6 Make sure sensor is not aimed within 20 feet of a road or sidewalk Passing cars will activate sensor Solution A 20 foot safety zone and reduced sensitivity are recommended to avoid activation from passing cars 7 Heavy rain snow or high winds may activate the sensor occasionally Reduce sensitivity control slightly until problem stops 8 Moths can be attracted to the lights and fly close to the sensor causing triggering Reducing the sensitivity may help 9 Check Solutions 3 4 5 6 7 and 8 under If Lights Do Not Turn Off Technical Tips Lights Turn On and Off Inappropriately 1 Check that lamps and fixtures work Compare wiring to the wiring diagram in this manual Check that the power is on 2 If installing during daylight remember that the sensor will provide 2 minutes of Test Time after power is turned on After 2 minutes the sensor will switch to Automatic Mode and will not work during day light if the photocell control is turned to the night only position moon symbol If you require 2 more minutes of Test Time turn the power off for at least 10 seconds and back on again If you require the sensor to operate both day and night turn the SUN MOON control knob clockwise to the sun and moon symbol 3 Check that lights from another source such as adjacent porch lights garden lights or street lights are not in the sensor s view The sen sor s photocel
28. not directly towards sensor Sensor will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 BON Zone de s curit de 20 pi MINUTERIE DE SOIR E MINUTERIE Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at tra
29. on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To
30. problems difficult to troubleshoot Single sensors that control their own lights will give a more accurate location of movement and trouble free operation Multiple Fixtures Multiple fixtures may be wired to a single sensor To handle loads greater than 1 000 watts a qualified electrician should install a relay Power Quality It is not recommended to install sensors on a circuit that also feeds motor loads such as HVAC equipment kitchen appliances or garage door openers The Stealth circuit is surge and transient protected to IEC specifications However if voltage varies significantly from 120 volts which may occur on circuits with motor loads the sensor may malfunction 10 Power In White Red Black Power In White Sensor Red Black 9 Black Rouge Blanc Noir Blanc Entr e lectrique D tecteur Condensateur de 400 V c c Relais capable d accepter la charge requise Entr e lectrique Adjusting the Settings TIME Sets the time that lights will remain on after the detection zone is vacated Adjustable from approximately 5 seconds to 12 minutes The Factory Setting is 12 minutes PHOTOCELL For night only operation turn the knob completely counterclockwise to to the MOON symbol For 24 hour operation turn the knob all the way clockwise to the MOON SUN symbol Adjust counterclockwise to have the sensor come on later at dusk clockwise to have it come on earlier The Fa
31. sensor is level 4 Sensitivity may be decreased with the SENS knob to detect a limited area or if the sensor is being activated by wind foliage traffic or animals or increased to cover a larger area See p 11 12 to adjust sensor settings The lens mask can also be used to drastically reduce coverage or allow undetected movement from some directions 5 STL360 is factory set for night only operation For 24 hour operation turn the photocell control completely toward the SUN MOON setting Turn counter clockwise to have the sensor come on later at dusk clockwise to have it come on earlier 6 Repeat steps 1 5 until you are satisfied with coverage Your sensor is now ready for operation Technical Tips Lights Do Not Turn Off 1 Make sure that the sensor is not in Manual Override Mode Turn power OFF for 10 seconds then ON Sensor will be in Test Mode for approximately 2 minutes then it will switch to Auto Mode with lights off and ready to detect movement 2 Make sure that the sensor is not in Evening Timer Mode Turn power OFF for 10 seconds see 1 3 Make sure sensor is not aimed at or mounted over something that would move or change temperature such as waving branches water air condi tioners windows or heating vents even on neighboring property You can test for infrared sources in the area by placing a box or bag over the sensor Put sensor into test mode Lights should stay off Wave your hand inside bag in front
32. threaded arms of each floodlight into the RC CU4 EZ Plate See diagram on page 7 2 Screw the threaded arm of the sensor into the bottom hole of the EZ Plate Sensor should be below and as far away from the floodlights as possible 3 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 4 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 5 Bring power leads light fixture and sensor leads through holes in all gaskets and mounting plates into junction box 6 Attach ground wire s to junction box grounding screw 7 Position EZ Plate gaskets and metal plate see pg 7 8 Strip 1 2 of insulation from all leads Connect as shown in wiring diagram 9 Twist on wire nuts Secure with electrical tape 10 Make sure all unused openings in EZ Plate are closed with plugs provided 11 Screw in light bulbs Turn on power 12 Conduct Walk Test to adjust sensor response see page 15 STL360 Assembly and Wiring Multiple Sensors Multiple sensors may be wired together but doing this will make problems difficult to troubleshoot Single sensors that control their own lights will give a more accurate location of movement and trouble free operation Multiple Fixtures Multiple fixtures may be
33. twice slowly off on off on within 1 2 secs Evening Timer to keep lights on for a set period each night Flip the switch three times slowly off on off on off on within 2 3 secs To Resume Auto Mode Switch power off for at least 10 seconds then back on Will STL360 detect animals STL360 may detect large animals Having animals trigger the sensor can give property a lived in look However you can limit animal detection by turning down the sensi tivity knob and or placing the blinders provided on the lower part of the forward lens How do you make adjustments to the sensor Use the adjustment tool provided or a screwdriver with a 1 8 wide blade to adjust the controls on the front of the sensor see page 11 12 2 On Guard Auto Mode LEDs scan continuously back amp forth Ready for Manual Override Mode Middle LED on Test Mode All LEDs off controls TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 1 How Does the Super Stealth 360 Work The STL360 s infrared sensor sees temperature changes caused by the motion of people or cars within its protection zone and turns on lights automatically It welcomes visitors and may deter intruders Total coverage Two sensors in one Two powerful detectors combine to give the STL360 Can t Miss Detection 180 long forward range 180 x 60 plus superb 360 detection below and to all sides How do the scanni
34. un Deux puissants d tecteurs conf rent au STL360 une d tection infaillible avant de 180 de longueur 180 x 60 pi plus une superbe d tection sur 360 en dessous et sur tous les c t s Principe de fonctionnement des indicateurs D L de d tection Les D L de d tection loignent les intrus en signalant la pr sence d un dispositif de s curit Ils indiquent le mode de fonctionnement du STL360 Mode veille Quand le STL360 est en mode veille automa tique trois D L rouges explorent sans arr t jour et nuit sauf pendant les d tections alors que les luminaires command s s allument Mode test Quand le d tecteur est en mode test toutes les D L sont teintes Si le d tecteur est programm pour le fonction nement la nuit seulement les D L restent en veille les d tections de jour n allument pas les lumi naires Mode contournement manuel En mode contournement manuel la D L du centre est allum e voir page 14 Principe de fonctionnement du Super Stealth 360 How Does the Super Stealth 360 Work The STL360 s infrared sensor sees temperature changes caused by the motion of people or cars within its protection zone and turns on lights automatically It welcomes visitors and may deter intruders Total coverage Two sensors in one Two powerful detectors combine to give the STL360 Can t Miss Detection 180 long forward range 180 x 60
35. wiring 5 Bring power leads light fixture and sensor leads through holes in all gaskets and mounting plates into junction box 6 Attach ground wire s to junction box grounding screw 7 Position EZ Plate gaskets and metal plate see pg 7 8 Strip 1 2 of insulation from all leads Connect as shown in wiring diagram 9 Twist on wire nuts Secure with electrical tape 10 Make sure all unused openings in EZ Plate are closed with plugs provided 11 Screw in light bulbs Turn on power 12 Conduct Walk Test to adjust sensor response see page 15 STL360 Assembly and Wiring Multiple Sensors Multiple sensors may be wired together but doing this will make problems difficult to troubleshoot Single sensors that control their own lights will give a more accurate location of movement and trouble free operation Multiple Fixtures Multiple fixtures may be wired to a single sensor To handle loads greater than 1 000 watts a qualified electrician should install a relay Power Quality It is not recommended to install sensors on a circuit that also feeds motor loads such as HVAC equipment kitchen appliances or garage door openers The Stealth circuit is surge and transient protected to IEC specifications However if voltage varies significantly from 120 volts which may occur on circuits with motor loads the sensor may malfunction 10 Power In White Red Black Power In White Sensor Red Bla
36. you set Manual Override while set to 24 hour operation lights will come on and remain on continuosly Lights will not turn off at dawn Sensor Modes AUTOMATIC MODE Lights will turn on when there is movement with in the detection zone after dusk EVENING TIMER MODE Keeps lights on for 1 8 hours after dusk Sensor then reverts to Automatic Mode until dawn If you set the Evening Timer Mode during daylight the sensor will be prepared to turn on at dusk and remain on for the number of hours you set When the sensor is in Ready for Evening Timer Mode the middle LED will blink 3 times pause and repeat Set the Evening Timer by flipping the switch that operates the sensor 3 times within 3 seconds off on off on off on TEST MODE To enter Test Mode turn power off for 10 seconds then back on There is a 30 second warm up period then the Test Mode starts During the warm up the lights stay on continiously and LEDs are off During the Test Period the sensor will keep lights on for 3 seconds each time it detects movement in its detection zone The sensor will revert back to Automatic Mode after 2 minutes of Test Mode However if you keep testing continuously the sensor will stay in Test Mode To end Test Mode you must vacate the detection zone for 1 minute or more Scanning LEDs will appear when test mode ends If you require 2 more minutes of Test Mode turn the power off for at least 10 seconds and back on again
37. 00 888 RAB 1232 888 RAB 1236 E mail www rabweb com Questions and requests Visit our internet site answered promptly for product information tech rabweb com RAB Lighting 170 Ludlow Avenue Northvale New Jersey 07647 U S A RAB Lighting 2004 Incorrect Correct 22 21 STL360Q1 Projecteur au quartz socle double de 150 watts STL360Q2 2 lampes Projecteur au quartz socle double de 2 watts STL360Q3 Projecteur au quartz socle double de 300 watts STL360H 2 lampes 150 watts PAR38 STL360HB 2 lampes 150 watts PAR38 NOTE Tous les luminaires au quartz socle double doivent tre install s avec la lampe l horizontale ou parall le au sol Si le luminaire est inclin la dur e de vie de la lampe sera r duite Replacement Lamps STL360Q1 150 watt double ended quartz flood STL360Q2 2 lamps 150 watt double ended quartz flood STL360Q3 300 watt double ended quartz flood STL360H 2 lamps 150 watt PAR38 STL360HB 2 lamps 150 watt PAR38 NOTE All double ended quartz fixtures must be mounted with the lamp horizontal or parallel to the ground If the fixture is tilted the lamp will fail prematurely Limited Warranty Your STL360 will be replaced or repaired at our option if it proves to be defective in workmanship or materials within ten years from the date of original purchase For repair replacement return the product freight prepaid and insured to RAB Lighting 170 Ludlow Avenue Northvale
38. 0Q1 STL360Q3W STL360Q2W Installation Manual Mises en garde COUPER LE COURANT AU DISJONCTEUR PANNEAU DE FUSIBLES Lire le manuel d installation au complet avant de continuer Tout le c blage doit tre conforme aux codes locaux de l lectricit et doit tre effectu par un lectricien comp tent La charge d clairage totale raccord e au STL360 ne doit pas d passer 8 A incandescence ou quartz de 1000 watts fluorescence de 250 watts Pour accro tre la puissance un lectricien peut installer un relais Les syst mes commande distance reli s au c blage comme X 10 Leviton ou Radio Shack sont incompatibles avec les d tecteurs et provoquent de faux d clenchements Ne pas installer sur un circuit qui alimente des charges moteur comme des appareils de cuisine de l quipement de climatisation une laveuse s cheuse ou un ouvre porte de garage Le d tecteur fonctionne mieux si le mouvement pr vu survient l int rieur de sa configuration de d tection et non en direction du d tecteur Installer entre 6 pi et 12 pi de hauteur pour une port e et une d tection optimales Le d tecteur infrarouge STL360 voit les petits carts de temp rature produits par le mouvement des personnes ou des voitures circulant dans sa zone de d tection et allume les lampes automatiquement Il accueille les visiteurs et loigne les intrus Protection totale Deux d tecteurs en
39. 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 11 MINUTERIE SENSIBILIT R gle la dur e pendant laquelle les luminaires resteront allum s apr s que la zone de d tection est d gag e R glable d environ 5 secondes 12 minutes Le r glage de l usine est 12 minutes Adjusting the Settings TIME Sets the time that lights will remain on after the detection zone is vacated Adjustable from approximately 5 seconds to 12 minutes The Factory Setting is 12 minutes PHOTOCELL For night only operation turn the knob completely counterclockwise to to the MOON symbol For 24 hour operation turn the knob all the way clockwise to the MOON SUN symbol Adjust counterclockwise to have the sensor come on later at dusk clockwise to have it come on earlier The Factory Setting is Night only MOON If you set Evening Timer while set to 24 hour operation Evening Timer will begin immediately after flipping switch SENSITIVITY Increases or decreases the responsiveness and range of the sensor adjustable from 30 to 100 The Factory Setting is 100 Adjusting the Settings EVENING TIMER The STL360 provides an alternative to normal motion activated lighting The EVENING TIMER can keep lights on continuously without motion for 1 to 8 hours after dusk This is great for evening activities requiring continuous light During vacations the EVENING TIMER provides a
40. 360 floodlight kits come pre wired and assembled on the RAB CU4 EZ plate allowing for mounting on round rectangular or octagonal surface or recessed boxes Mounting Wiring STL360 Kit Assembly and Wiring 1 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 2 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 3 Bring power leads and sensor kit leads through holes in all gaskets into junction box 4 Strip 1 2 of insulation from all leads 5 Attach ground wire s to junction box grounding screw Connect as shown in wiring diagram on page 7 6 Twist on wire nuts Secure with electrical tape 7 Align gaskets EZ Plate and metal mounting plate to insure proper seal Tighten EZ Plate center screw make sure O Ring gasket is on the screw to attach EZ Plate to the box 8 Insert plastic Finishing Cap in the center of the CU4 EZ Plate for a weatherproof seal 9 Use silicone sealant around all openings to insure a weatherproof seal 10 Screw in light bulbs Turn on power Conduct walk test to adjust sensor response see page 15 Insert close up plug in unused hole Finishing Cap Metal Mounting Plate Bar Screws Gasket Universal Mounting Bar Gasket O Ring Gas
41. 5 Moins Sensible Plus sensible Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in pr
42. DE SOIR E actionner lente ment trois fois l interrupteur mural qui commande le d tecteur arr t marche arr t marche arr t marche en 3 secondes Si la MINUTERIE DE SOIR E est programm e pendant le jour la D L du centre commence clignoter pour indiquer que la minuterie de soir e se mettra en marche au cr puscule Choisir la dur e d clairage permanent Par exemple si la MINUTERIE DE SOIR E est programm e 8 le d tecteur maintient les luminaires allum s sans arr t pendant 8 heures apr s le cr puscule Une fois les 8 heures coul es le d tect eur retourne en mode commande par mouvement l aube la photocellule d tecte la lumi re et emp che les luminaires de s allumer le jour Pour ne pas utiliser la MINUTERIE DE SOIR E NE PAS ac tionner l interrupteur 3 fois tel que d crit ci dessus Pour interrompre le fonctionnement de la MINUTERIE DE SOI R E couper le courant pendant au moins 10 secondes puis le r tablir Le d tecteur sera alors en mode automatique Apr s la p riode d chauffement On peut coller cette tiquette droite fournie la plaque d interrupteur du luminaire int rieur pour fins de r f rence Les luminaires s allument en cas de mouvement dans la zone de d tection apr s le cr puscule En mode test toutes les D L sont teintes MODE CONTOURNEMENT MANUEL Le STL360 dispose d un dispositif de contournement manuel prot g qui exige le d
43. EVENING TIMER switch OFF the power for at least 10 seconds then ON again Sensor will be in Automatic Mode After completing the warm up period You can affix this label right provided to your indoor light switch plate for easy reference 12 TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 11 R glage des param tres Adjusting the Settings TIME Sets the time that lights will remain on after the detection zone is vacated Adjustable from approximately 5 seconds to 12 minutes The Factory Setting is 12 minutes PHOTOCELL For night only operation turn the knob completely counterclockwise to to the MOON symbol For 24 hour operation turn the knob all the way clockwise to the MOON SUN symbol Adjust counterclockwise to have the sensor come on later at dusk clockwise to have it come on earlier The Factory Setting is Night only MOON If you set Evening Timer while set to 24 hour operation Evening Timer will begin immediately after flipping switch SENSITIVITY Increases or decreases the responsiveness and range of the sensor adjustable from 30 to 100 The Factory Setting is 100 Adjusting the Settings EVENING TIMER The STL360 provides an alternative to normal motion activated lighting The EVEN
44. ING TIMER can keep lights on continuously without motion for 1 to 8 hours after dusk This is great for evening activities requiring continuous light During vacations the EVENING TIMER provides a lived in look by simulating an occupant turning lights on at dusk and then off at bedtime To set the EVENING TIMER flip the wall switch controlling the sensor three times slowly off on off on off on within 3 seconds If you set the EVENING TIMER during daytime the middle LED should start blinking indicating that the Evening Timer will start when dusk is detected Choose the length of time you want continuous lighting For example if you set the EVENING TIMER to 8 the sensor will keep lights ON continuously for 8 hours after dusk Once 8 hours have passed the sensor will revert to motion activated mode At dawn the photocell will detect light and prevent lights from turning on during the daytime If you do not want to use the EVENING TIMER do NOT flip the switch 3 times as described above To end use of the EVENING TIMER switch OFF the power for at least 10 seconds then ON again Sensor will be in Automatic Mode After completing the warm up period You can affix this label right provided to your indoor light switch plate for easy reference 12 TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS
45. NG TIMER to 8 the sensor will keep lights ON continuously for 8 hours after dusk Once 8 hours have passed the sensor will revert to motion activated mode At dawn the photocell will detect light and prevent lights from turning on during the daytime If you do not want to use the EVENING TIMER do NOT flip the switch 3 times as described above To end use of the EVENING TIMER switch OFF the power for at least 10 seconds then ON again Sensor will be in Automatic Mode After completing the warm up period You can affix this label right provided to your indoor light switch plate for easy reference 12 TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 11 MINUTERIE DE SOIR E Le STL360 s av re une solution de rechange l clairage com mand par le mouvement normal La MINUTERIE DE SOIR E peut maintenir les luminaires allum s en permanence sans mouvement entre 1 et 8 heures apr s le cr puscule Id ale pour les activit s de soir e qui exigent un clairage permanent Pendant les vacances la MINUTERIE DE SOIR E donne une allure habit e en simulant l actionnement par un occupant des luminaires au cr puscule puis la d sactivation au coucher Pour programmer la MINUTERIE
46. Specifications Switching Capacity 8 amps 1000 watts Incandescent and 250 watts Fluorescent Voltage 120 volts Protection Pattern 180 forward 360 below and to all sides Time Adjustment 5 seconds to 12 minutes Power Consumption 1 watt Surge protection 6000 volts Cautions TURN OFF ALL POWER AT CIRCUIT BREAKER FUSE PANEL Read entire Installation Manual before proceeding All wiring should comply with local electrical codes and requires a qualified electrician The total lighting load connected to STL360 must not exceed 1000 watts incandescent or quartz 250 watts fluorescent To switch more wattage an electrician can install a relay Line Carrier Remote Control Systems such as X 10 Leviton or Radio Shack are incompatible with sensors and may cause false activations Do not install sensors on a circuit that feeds motor loads such as kitchen appliances HVAC equipment washer dryer or garage door openers Sensor functions best when the direction of expected movement is across its detection pattern not towards the sensor Mount 6 12 high for optimum range and detection The STEALTH360 is the most reliable and technically advanced motion activated light control ever produced This techni cal manual is written for electrical professionals who wish to maximize the performance and reliability of this superb sensor STL360H STL360HBW STL360Q1 STL360Q3W STL360Q2W Installation M
47. TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 11 Sensor Modes AUTOMATIC MODE Lights will turn on when there is movement with in the detection zone after dusk EVENING TIMER MODE Keeps lights on for 1 8 hours after dusk Sensor then reverts to Automatic Mode until dawn If you set the Evening Timer Mode during daylight the sensor will be prepared to turn on at dusk and remain on for the number of hours you set When the sensor is in Ready for Evening Timer Mode the middle LED will blink 3 times pause and repeat Set the Evening Timer by flipping the switch that operates the sensor 3 times within 3 seconds off on off on off on TEST MODE To enter Test Mode turn power off for 10 seconds then back on There is a 30 second warm up period then the Test Mode starts During the warm up the lights stay on continiously and LEDs are off During the Test Period the sensor will keep lights on for 3 seconds each time it detects movement in its detection zone The sensor will revert back to Automatic Mode after 2 minutes of Test Mode However if you keep testing continuously the sensor will stay in Test Mode To end Test Mode you must vacate the detection zone for 1 minute or more Scanning LEDs will appear when test mode ends If you require 2 more minutes of Test Mode turn the power off for at least 10 seconds a
48. Test Mode starts During the warm up the lights stay on continiously and LEDs are off During the Test Period the sensor will keep lights on for 3 seconds each time it detects movement in its detection zone The sensor will revert back to Automatic Mode after 2 minutes of Test Mode However if you keep testing continuously the sensor will stay in Test Mode To end Test Mode you must vacate the detection zone for 1 minute or more Scanning LEDs will appear when test mode ends If you require 2 more minutes of Test Mode turn the power off for at least 10 seconds and back on again In Test Mode no LEDs are lit MANUAL OVERRIDE MODE The STL360 has a protected Manual Override that requires a double flip of the light switch so momentary power problems do not interfere with normal sensor operation By flipping the switch that operates the sensor twice off on off on within 2 seconds you will override the sensor to keep lights on continuously until dawn If you set the Manual Override Mode during daylight the sensor will be prepared to turn on at dusk and remain on until dawn This is a handy feature if you leave home for the day and you want the lights on to greet you when you return When the sensor is in Ready for Manual Override Mode the middle LED will be on TO RESUME AUTOMATIC MODE Switch OFF the power for at least 10 seconds then turn it ON again Sensor will reset to Automatic Mode after completing the w
49. age If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 Choisir un emplacement Endroits pr s des routes Les voitures et la circulation peuvent d clencher le d tecteur s il est orient vers la route Pour am liorer le rendement dans les endroits pr s des routes R duire la sensibilit en tournant le bouton SENS vers la gauche Choosing a Location Locations Near Roads Cars a
50. and par un interrupteur int rieur ordinaire ou un disjoncteur Le STL360 fonctionne en mode automatique sauf s il est chang On peut allumer ou teindre les lampes manuellement uniquement la nuit Voir les pages 13 14 pour en savoir plus Mode contournement manuel pour maintenir les luminaires allum s Actionner lentement l interrupteur deux fois arr t marche arr t marche en 1 ou 2 secondes Minuterie de soir e pour maintenir les luminaires allum s pendant une p riode programm e chaque nuit Actionner lentement l interrupteur trois fois arr t marche arr t marche arr t marche en 2 3 secondes Pour r tablir le mode automatique Couper le courant pendant au moins 10 secondes puis le r tablir Le STL360 d tecte t il les animaux Le STL360 peut d tecter les gros animaux Le fait que des animaux d clenchent le d tecteur peut contribuer donner l impression que la maison est habit e On peut cependant limiter la d tection des animaux en tournant le bouton de sen sibilit et ou en pla ant les masques fournis sur la partie inf rieure de la lentille avant Comment ajuster le d tect eur Utiliser l outil d ajustement fourni ou un tournevis lame de 1 8 po pour ajuster les com mandes l avant du d tecteur voir pages 11 12 How Does the Super Stealth 360 Work The STL360 s infrared sensor sees temperature changes caused by the motion of people or cars withi
51. anual Thank you for buying RC lighting fixtures Our aim is to design the best quality products to get the job done right We d like to hear your comments Call the Marketing Department at 888 722 1000 or email marketing rclighting ca How Does the Super Stealth 360 Work The STL360 s infrared sensor sees temperature changes caused by the motion of people or cars within its protection zone and turns on lights automatically It welcomes visitors and may deter intruders Total coverage Two sensors in one Two powerful detectors combine to give the STL360 Can t Miss Detection 180 long forward range 180 x 60 plus superb 360 detection below and to all sides How do the scanning LED detection indicators work Scanning LEDs serve as a deterrent by indicating a securi ty device in operation They also show the STL360 s mode of operation On Guard When the STL360 is On Guard in Auto mode three red LEDs scan continu ously day and night except during detections at which time the controlled lights will go on Test Mode When the sensor is in Test Mode all the LEDs will be off If the sensor is set for night only operation the LED stays On Guard daytime detections do not turn on the lights Manual Override Mode In Manual Override Mode the middle LED will be on see page 14 Howhe SuperSTL360 360 Work How Does the Super Stealth 360 Work How long do the li
52. ape 7 Align gaskets EZ Plate and metal mounting plate to insure proper seal Tighten EZ Plate center screw make sure O Ring gasket is on the screw to attach EZ Plate to the box 8 Insert plastic Finishing Cap in the center of the CU4 EZ Plate for a weatherproof seal 9 Use silicone sealant around all openings to insure a weatherproof seal 10 Screw in light bulbs Turn on power Conduct walk test to adjust sensor response see page 15 Insert close up plug in unused hole Finishing Cap Metal Mounting Plate Bar Screws Gasket Universal Mounting Bar Gasket O Ring Gasket 8 Hook rests in notch on crossbar Hands Free Hanging Hook Black Black Red Red pigtail Ground Ground Power In White White Red pigtail is only used to switch remote or additional fixtures STL360H STL360Q2W STL360Q1 STL360Q3W STL360HBW CU4 EZ Plate Center Screw 7 CU4 EZ Plate Vis de barre Plaque de montage en m tal Plaque CU4 EZ Ins rer le bouchon dans le trou inutilis Vis centrale Capuchon de finition Joint Torique Joint Joint Barre de montage universelle Utiliser la queue de co chon rouge seulement pour commander les luminaires distance ou additionnels Rouge Noir Rouge queue de couchon Noir Entr e lectrique Blanc Blanc Mise la terre Mise la terre STL360 Kit Assembly and Wiring STL360 floodlight
53. arm up period and Test Mode 14 On Guard Auto Mode LEDs scan continuously back and forth Ready for Manual Override Mode Middle LED on Ready for Evening Timer Mode Middle LED blinks 13 DAYTIME 24 HOUR OPERATION OF MANUAL OVERRIDE If you set Manual Override while set to 24 hour operation lights will come on and remain on continuosly Lights will not turn off at dawn Les D L Mode automatique en veille explorent sans arr t Sensor Modes AUTOMATIC MODE Lights will turn on when there is movement with in the detection zone after dusk EVENING TIMER MODE Keeps lights on for 1 8 hours after dusk Sensor then reverts to Automatic Mode until dawn If you set the Evening Timer Mode during daylight the sensor will be prepared to turn on at dusk and remain on for the number of hours you set When the sensor is in Ready for Evening Timer Mode the middle LED will blink 3 times pause and repeat Set the Evening Timer by flipping the switch that operates the sensor 3 times within 3 seconds off on off on off on TEST MODE To enter Test Mode turn power off for 10 seconds then back on There is a 30 second warm up period then the Test Mode starts During the warm up the lights stay on continiously and LEDs are off During the Test Period the sensor will keep lights on for 3 seconds each time it detects movement in its detection zone The sensor will revert back to Automatic Mode after 2
54. as a Test Period which allows the sensor to be walk tested day or night To enter Test Mode The sensor is in Test Mode when power is first applied Turn power off for at least 10 seconds and back on 1 Aim the sensor at the traffic pattern you want to detect Sensor will detect any movement ACROSS its pattern most effectively 2 Start outside the pattern and walk across the pattern until the lights go on As distance from the sensor increases it will take more movement to be detected 3 Adjust sensor aiming as necessary to improve coverage Make sure sensor is level 4 Sensitivity may be decreased with the SENS knob to detect a limited area or if the sensor is being activated by wind foliage traffic or animals or increased to cover a larger area See p 11 12 to adjust sensor settings The lens mask can also be used to drastically reduce coverage or allow undetected movement from some directions 5 STL360 is factory set for night only operation For 24 hour operation turn the photocell control completely toward the SUN MOON setting Turn counter clockwise to have the sensor come on later at dusk clockwise to have it come on earlier 6 Repeat steps 1 5 until you are satisfied with coverage Your sensor is now ready for operation Technical Tips Lights Do Not Turn Off 1 Make sure that the sensor is not in Manual Override Mode Turn power OFF for 10 seconds then ON Sensor will be in Test Mode for approximately
55. atts Fluorescent Voltage 120 volts Protection Pattern 180 forward 360 below and to all sides Time Adjustment 5 seconds to 12 minutes Power Consumption 1 watt Surge protection 6000 volts Cautions TURN OFF ALL POWER AT CIRCUIT BREAKER FUSE PANEL Read entire Installation Manual before proceeding All wiring should comply with local electrical codes and requires a qualified electrician The total lighting load connected to STL360 must not exceed 1000 watts incandescent or quartz 250 watts fluorescent To switch more wattage an electrician can install a relay Line Carrier Remote Control Systems such as X 10 Leviton or Radio Shack are incompatible with sensors and may cause false activations Do not install sensors on a circuit that feeds motor loads such as kitchen appliances HVAC equipment washer dryer or garage door openers Sensor functions best when the direction of expected movement is across its detection pattern not towards the sensor Mount 6 12 high for optimum range and detection The STEALTH360 is the most reliable and technically advanced motion activated light control ever produced This techni cal manual is written for electrical professionals who wish to maximize the performance and reliability of this superb sensor RAB welcomes your questions or comments Please call 888 722 1000 or email tech rabweb com Thank you for purchasing a RAB sensor STL360H STL360HBW STL36
56. box you must use both gaskets with the metal mounting plate sandwiched between 2 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 3 Bring power leads and sensor kit leads through holes in all gaskets into junction box 4 Strip 1 2 of insulation from all leads 5 Attach ground wire s to junction box grounding screw Connect as shown in wiring diagram on page 7 6 Twist on wire nuts Secure with electrical tape 7 Align gaskets EZ Plate and metal mounting plate to insure proper seal Tighten EZ Plate center screw make sure O Ring gasket is on the screw to attach EZ Plate to the box 8 Insert plastic Finishing Cap in the center of the CU4 EZ Plate for a weatherproof seal 9 Use silicone sealant around all openings to insure a weatherproof seal 10 Screw in light bulbs Turn on power Conduct walk test to adjust sensor response see page 15 Insert close up plug in unused hole Finishing Cap Metal Mounting Plate Bar Screws Gasket Universal Mounting Bar Gasket O Ring Gasket 8 Hook rests in notch on crossbar Hands Free Hanging Hook Black Black Red Red pigtail Ground Ground Power In White White Red pigtail is only used to switch remote or additional fixtures STL360H STL360Q2W STL360Q1 STL360Q3W STL360HBW CU4 EZ Plate Center Screw 7 CU4 EZ Plate STL360 Kit Assembly and Wiring STL
57. bustible surfaces Side View 6 10 wrong wrong OK TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 20 40 6 10 60 Reduced Range Maximum Range mask 4 3 60 60 20 Choisir un emplacement Choisir un endroit o le d tecteur peut voir tous les parcours de mouvement Le d tecteur peut tre fix au mur ou au soffite Plus la distance par rapport au d tecteur est grande plus il est difficile de d tecter le mouvement Par exemple 10 pieds un demi pas suffit alors qu 50 pieds il faut plusieurs pas Le STL360 prot ge quelle grandeur de zone Deux puissants d tecteurs conf rent au STL360 une d tection avant de 180 x 60 pi de longueur plus une superbe d tection sur 360 en dessous et sur tous les c t s Choosing a Location The best location is where the sensor can see all paths of movement The sensor may be wall or soffit mounted As distance from the sensor increases larger movement will be required for detection For instance at 10 feet a half step will be enough while at 50 feet several steps will be necessary for detection How large an area does STL360 protect Two powerful detectors combine to give the STL360 180 x 60 long forward range plus superb 360 downward detection below and to all sides Mounting Height Mounting at 6 12 above the ground allows maximum range If the sensor is mounted above 15
58. ch as HVAC equipment kitchen appliances or garage door openers 2 It is not recommended to wire sensors in parallel More than one sensor wired together makes them difficult to troubleshoot Disconnect multi ple sensors and test separately 3 Keep all people completely out of the detection pattern to make sure the sensor is not detecting them 4 Make sure sensor is located below and as far as possible from its lights Heat from the lights may trigger the sensor Solution Move sensor below and away from the lights 5 Make sure lights are not reflecting back into sensor Check for white or reflective surfaces close to the sensor Solution Aim sensor away from reflective objects or move the objects and lower sensitivity 6 Make sure sensor is not aimed within 20 feet of a road or sidewalk Passing cars will activate sensor Solution A 20 foot safety zone and reduced sensitivity are recommended to avoid activation from passing cars 7 Heavy rain snow or high winds may activate the sensor occasionally Reduce sensitivity control slightly until problem stops 8 Moths can be attracted to the lights and fly close to the sensor causing triggering Reducing the sensitivity may help 9 Check Solutions 3 4 5 6 7 and 8 under If Lights Do Not Turn Off Technical Tips Lights Turn On and Off Inappropriately 1 Check that lamps and fixtures work Compare wiring to the wiring diagram in this manual Check that t
59. ck 9 Black STL360 Assembly and Wiring To install a STL360 Sensor with separately purchased floodlights start at 1 To install STL360 Pre wired Floodlight Kits see page 7 1 Screw the threaded arms of each floodlight into the RAB CU4 EZ Plate See diagram on page 7 2 Screw the threaded arm of the sensor into the bottom hole of the EZ Plate Sensor should be below and as far away from the floodlights as possible 3 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 4 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 5 Bring power leads light fixture and sensor leads through holes in all gaskets and mounting plates into junction box 6 Attach ground wire s to junction box grounding screw 7 Position EZ Plate gaskets and metal plate see pg 7 8 Strip 1 2 of insulation from all leads Connect as shown in wiring diagram 9 Twist on wire nuts Secure with electrical tape 10 Make sure all unused openings in EZ Plate are closed with plugs provided 11 Screw in light bulbs Turn on power 12 Conduct Walk Test to adjust sensor response see page 15 STL360 Assembly and Wiring Multiple Sensors Multiple sensors may be wired together but doing this will make
60. ck amp forth Ready for Manual Override Mode Middle LED on Test Mode All LEDs off controls TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 1 Choosing a Location The best location is where the sensor can see all paths of movement The sensor may be wall or soffit mounted As distance from the sensor increases larger movement will be required for detection For instance at 10 feet a half step will be enough while at 50 feet several steps will be necessary for detection How large an area does STL360 protect Two powerful detectors combine to give the STL360 180 x 60 long forward range plus superb 360 downward detection below and to all sides Mounting Height Mounting at 6 12 above the ground allows maximum range If the sensor is mounted above 15 high the usable range is reduced Location Tips Difficult Locations Sensor may be triggered by unwanted movement or heat source such as a swaying tree road traffic dryer vent swimming pool or hot tub To Improve Performance in Difficult Locations Reduce sensitivity by turning the SENS knob counterclockwise and or Mask lens in the direction of the unwanted movement or heat source using the lens mask provided or opaque tape Mounting Stability Mount sensor on stable surface Do not mount on a tree or pole that will move in the wind Make sure sensor and lights are mounted firmly If they mo
61. comes visitors and may deter intruders Total coverage Two sensors in one Two powerful detectors combine to give the STL360 Can t Miss Detection 180 long forward range 180 x 60 plus superb 360 detection below and to all sides How do the scanning LED detection indicators work Scanning LEDs serve as a deterrent by indicating a securi ty device in operation They also show the STL360 s mode of operation On Guard When the STL360 is On Guard in Auto mode three red LEDs scan continu ously day and night except during detections at which time the controlled lights will go on Test Mode When the sensor is in Test Mode all the LEDs will be off If the sensor is set for night only operation the LED stays On Guard daytime detections do not turn on the lights Manual Override Mode In Manual Override Mode the middle LED will be on see page 14 Howhe SuperSTL360 360 Work How Does the Super Stealth 360 Work How long do the lights stay on Lights remain on as long as there is movement within the protection zone Once the zone is vacated lights can be adjusted to remain on from approximately 5 seconds up to 12 minutes Since the lights are on only when needed and the sensor uses only one watt the STL360 is extremely energy efficient Can lights still be turned on with the light switch Yes STL360 can be controlled by a conventional indoor switch or circuit breaker Th
62. ctionner le jour et la nuit tourner la com mande centrale vers la droite jusqu au symbole de SOLEIL LUNE 3 V rifier que les luminaires d une autre source comme celles d un porche proximit du jardin ou de la rue ne se trouvent pas dans la zone de d tection du d tecteur La photocellule du d tect eur peut d tecter la lumi re et d sactiver la lumi re du jour Pour que le d tecteur fonctionne des niveaux d clairage ambi ant sup rieurs tourner le bouton de commande vers le symbole de soleil 4 Le d tecteur a t il t raccord sous tension Si c est le cas les circuits peuvent avoir t endom mag s 1 Make sure the sensor is installed on its own dedicated circuit free of motor loads such as HVAC equipment kitchen appliances or garage door openers 2 It is not recommended to wire sensors in parallel More than one sensor wired together makes them difficult to troubleshoot Disconnect multi ple sensors and test separately 3 Keep all people completely out of the detection pattern to make sure the sensor is not detecting them 4 Make sure sensor is located below and as far as possible from its lights Heat from the lights may trigger the sensor Solution Move sensor below and away from the lights 5 Make sure lights are not reflecting back into sensor Check for white or reflective surfaces close to the sensor Solution Aim sensor away from reflective objects or
63. ctory Setting is Night only MOON If you set Evening Timer while set to 24 hour operation Evening Timer will begin immediately after flipping switch SENSITIVITY Increases or decreases the responsiveness and range of the sensor adjustable from 30 to 100 The Factory Setting is 100 Adjusting the Settings EVENING TIMER The STL360 provides an alternative to normal motion activated lighting The EVENING TIMER can keep lights on continuously without motion for 1 to 8 hours after dusk This is great for evening activities requiring continuous light During vacations the EVENING TIMER provides a lived in look by simulating an occupant turning lights on at dusk and then off at bedtime To set the EVENING TIMER flip the wall switch controlling the sensor three times slowly off on off on off on within 3 seconds If you set the EVENING TIMER during daytime the middle LED should start blinking indicating that the Evening Timer will start when dusk is detected Choose the length of time you want continuous lighting For example if you set the EVENING TIMER to 8 the sensor will keep lights ON continuously for 8 hours after dusk Once 8 hours have passed the sensor will revert to motion activated mode At dawn the photocell will detect light and prevent lights from turning on during the daytime If you do not want to use the EVENING TIMER do NOT flip the switch 3 times as described above To end use of the
64. detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 Masque de lentille inclus Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is
65. double ended quartz flood STL360Q3 300 watt double ended quartz flood STL360H 2 lamps 150 watt PAR38 STL360HB 2 lamps 150 watt PAR38 NOTE All double ended quartz fixtures must be mounted with the lamp horizontal or parallel to the ground If the fixture is tilted the lamp will fail prematurely Limited Warranty Your STL360 will be replaced or repaired at our option if it proves to be defective in workmanship or materials within ten years from the date of original purchase For repair replacement return the product freight prepaid and insured to RAB Lighting 170 Ludlow Avenue Northvale NJ 07647 The STL360 should be packed carefully Please include your sales receipt and a description of the problem If your unit is out of warranty or the damage is unrelated to the original manufacture return your unit directly to us with a check for 20 00 made out to RAB Electric We will repair or replace your unit Under no circumstances shall we be liable for any incidental or consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property or revenue or cost of installation removal or re installation This warranty gives you specific legal rights and you may also have other rights which vary from state to state Contents of Accessory Kit 2 Lens Masks Indoor Switchplate Label 3 Wire Nuts Adjustment Tool Mylar Len
66. ducing the sensitivity may help 9 Check Solutions 3 4 5 6 7 and 8 under If Lights Do Not Turn Off Technical Tips Lights Turn On and Off Inappropriately 1 Check that lamps and fixtures work Compare wiring to the wiring diagram in this manual Check that the power is on 2 If installing during daylight remember that the sensor will provide 2 minutes of Test Time after power is turned on After 2 minutes the sensor will switch to Automatic Mode and will not work during day light if the photocell control is turned to the night only position moon symbol If you require 2 more minutes of Test Time turn the power off for at least 10 seconds and back on again If you require the sensor to operate both day and night turn the SUN MOON control knob clockwise to the sun and moon symbol 3 Check that lights from another source such as adjacent porch lights garden lights or street lights are not in the sensor s view The sen sor s photocell may detect the light and deactivate daylight If you desire the sensor to operate in higher ambient light levels turn the SUN MOON control knob counter clockwise toward the sun symbol 4 Was sensor wired hot If so circuitry may have been damaged Technical Tips Lights Do Not Turn On 20 safety zone TIME 12 MINS SENS TIME 12 MINS SENS 18 17 WRONG OK Technical Tips Lights Turn Off Too Quickly 1 Check if sensor is be
67. e STL360 operates in Auto Mode unless changed The light can be turned on or off manually at night only see pages 13 14 for more info Manual Override Mode to keep lights on Flip the switch twice slowly off on off on within 1 2 secs Evening Timer to keep lights on for a set period each night Flip the switch three times slowly off on off on off on within 2 3 secs To Resume Auto Mode Switch power off for at least 10 seconds then back on Will STL360 detect animals STL360 may detect large animals Having animals trigger the sensor can give property a lived in look However you can limit animal detection by turning down the sensi tivity knob and or placing the blinders provided on the lower part of the forward lens How do you make adjustments to the sensor Use the adjustment tool provided or a screwdriver with a 1 8 wide blade to adjust the controls on the front of the sensor see page 11 12 2 On Guard Auto Mode LEDs scan continuously back amp forth Ready for Manual Override Mode Middle LED on Test Mode All LEDs off controls TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 1 Les D L de mode veille explorent sans arr t dans un sens et l autre Mode test Tous les D L sont teintes Pr t pour le mode contournement manuel D L du centre allum e Choosing a Location The best location is where the sensor can see all pat
68. e de garage Le circuit Stealth est prot g contre les surtensions et les parasites conform ment aux normes IEC Cependant si la tension varie consid rablement par rapport 120 volts ce qui peut survenir sur les circuits avec charges moteur le d tecteur peut fonctionner incorrectement Assemblage et raccordement du STL360 Pour installer un d tecteur STL360 avec des project eurs achet s s par ment commencer l tape 1 Pour installer les trousses de projecteurs pr c bl s STL360 voir la page 7 1 Visser les bras filet s de chaque projecteur dans la plaque RC Lighting CU4 EZ Voir le sch ma la page 7 2 Visser le bras filet du d tecteur dans le trou inf rieur de la plaque EZ Le d tecteur doit tre en dessous et aussi loin que possible des projecteurs 3 Fixer la barre de montage universelle au moyen des vis de barre fournies la bo te de jonction Si on fixe la trousse STL360 une bo te murale r sistant aux intem p ries on doit utiliser les deux joints et placer la plaque de montage de m tal entre les deux 4 Conseil de raccordement simple Utiliser le crochet de fixation en S mains libres pour retenir la plaque EZ pendant le raccordement 5 Acheminer les conducteurs d alimentation les conducteurs de luminaire et de d tecteur par les trous de tous les joints et des plaques de montage dans la bo te de jonction 6 Fixer le ou les fils de terre la vis de mise la te
69. e from approximately 5 seconds to 12 minutes The Factory Setting is 12 minutes PHOTOCELL For night only operation turn the knob completely counterclockwise to to the MOON symbol For 24 hour operation turn the knob all the way clockwise to the MOON SUN symbol Adjust counterclockwise to have the sensor come on later at dusk clockwise to have it come on earlier The Factory Setting is Night only MOON If you set Evening Timer while set to 24 hour operation Evening Timer will begin immediately after flipping switch SENSITIVITY Increases or decreases the responsiveness and range of the sensor adjustable from 30 to 100 The Factory Setting is 100 Adjusting the Settings EVENING TIMER The STL360 provides an alternative to normal motion activated lighting The EVENING TIMER can keep lights on continuously without motion for 1 to 8 hours after dusk This is great for evening activities requiring continuous light During vacations the EVENING TIMER provides a lived in look by simulating an occupant turning lights on at dusk and then off at bedtime To set the EVENING TIMER flip the wall switch controlling the sensor three times slowly off on off on off on within 3 seconds If you set the EVENING TIMER during daytime the middle LED should start blinking indicating that the Evening Timer will start when dusk is detected Choose the length of time you want continuous lighting For example if you set the EVENI
70. e le d tecteur ne les d tecte pas 4 S assurer que le d tecteur est install sous ses luminaires et aussi loin que possible de ceux ci La chaleur produite par les luminaires peut d clencher le d tecteur Solution D placer le d tecteur sous les luminaires et l loigner de ceux ci 5 S assurer que les lampes ne r fl chissent pas la lumi re dans le d tecteur V rifier la pr sence de surfaces blanches ou r fl chissantes pr s du d tecteur Solution Diriger le d tecteur ailleurs que sur des objets r fl chissants ou d placer les objets et r duire la sensibilit 6 S assurer que le d tecteur n est pas point moins de 20 pieds d une route ou d un trottoir Les voitures d clenchent le d tecteur Solution On recommande une zone de s curit de 20 pieds et de r duire la sensibilit pour viter que les voitures ne d clenchent le d tecteur 7 La forte pluie la neige ou les forts vents peuvent parfois d clencher le d tecteur Baisser l g rement la commande de sensibilit jusqu ce que le probl me soit corrig 8 Les papillons de nuit peuvent tre attir s par les luminaires et atteindre et d clencher le d tecteur R duire la sensibilit peut am liorer la situ ation 9 V rifier les solutions 3 4 5 6 7 et 8 sous Si les luminaires ne s teignent pas 1 Make sure the sensor is installed on its own dedicated circuit free of motor loads su
71. en you return When the sensor is in Ready for Manual Override Mode the middle LED will be on TO RESUME AUTOMATIC MODE Switch OFF the power for at least 10 seconds then turn it ON again Sensor will reset to Automatic Mode after completing the warm up period and Test Mode 14 On Guard Auto Mode LEDs scan continuously back and forth Ready for Manual Override Mode Middle LED on Ready for Evening Timer Mode Middle LED blinks 13 DAYTIME 24 HOUR OPERATION OF MANUAL OVERRIDE If you set Manual Override while set to 24 hour operation lights will come on and remain on continuosly Lights will not turn off at dawn Pr t pour le mode minuterie de soir e La D L du centre clignote Sensor Modes AUTOMATIC MODE Lights will turn on when there is movement with in the detection zone after dusk EVENING TIMER MODE Keeps lights on for 1 8 hours after dusk Sensor then reverts to Automatic Mode until dawn If you set the Evening Timer Mode during daylight the sensor will be prepared to turn on at dusk and remain on for the number of hours you set When the sensor is in Ready for Evening Timer Mode the middle LED will blink 3 times pause and repeat Set the Evening Timer by flipping the switch that operates the sensor 3 times within 3 seconds off on off on off on TEST MODE To enter Test Mode turn power off for 10 seconds then back on There is a 30 second warm up period then the
72. er dusk EVENING TIMER MODE Keeps lights on for 1 8 hours after dusk Sensor then reverts to Automatic Mode until dawn If you set the Evening Timer Mode during daylight the sensor will be prepared to turn on at dusk and remain on for the number of hours you set When the sensor is in Ready for Evening Timer Mode the middle LED will blink 3 times pause and repeat Set the Evening Timer by flipping the switch that operates the sensor 3 times within 3 seconds off on off on off on TEST MODE To enter Test Mode turn power off for 10 seconds then back on There is a 30 second warm up period then the Test Mode starts During the warm up the lights stay on continiously and LEDs are off During the Test Period the sensor will keep lights on for 3 seconds each time it detects movement in its detection zone The sensor will revert back to Automatic Mode after 2 minutes of Test Mode However if you keep testing continuously the sensor will stay in Test Mode To end Test Mode you must vacate the detection zone for 1 minute or more Scanning LEDs will appear when test mode ends If you require 2 more minutes of Test Mode turn the power off for at least 10 seconds and back on again In Test Mode no LEDs are lit MANUAL OVERRIDE MODE The STL360 has a protected Manual Override that requires a double flip of the light switch so momentary power problems do not interfere with normal sensor operation By flipping the
73. erie de soir e Couper le courant pendant 10 secondes voir 1 3 S assurer que le d tecteur n est pas fix ou dirig vers un objet qui peut bouger ou changer de temp rature comme des branches au vent de l eau des climatiseurs des fen tres ou des bouches de chauff age m me sur une propri t avoisinante On peut tester les sources infrarouges dans la zone en pla ant une bo te ou un sac sur le d tecteur Mettre le d tecteur en mode test Les lumi res devraient rester teintes Remuer la main l int rieur du sac devant le d tecteur Les luminaires devraient s allumer puis s teindre apr s le d lai pr vu Si le d tecteur fonctionne correctement lorsqu il est recouvert v rifier les points 4 8 Probl me Le d tecteur est d clench par un mouvement parasite ou une source de chaleur Solution 1 Diriger le d tecteur loin du mouvement ou 2 Masquer la lentille en direction de la source 3 R duire le r glage de la commande de sensibilit 4 S assurer que le d tecteur et les luminaires sont solidement fix s et ne bougent pas m me lorsqu on les touche l g rement S ils bougent serrer toutes les vis 5 S assurer que le d tecteur n est pas fix un objet instable comme un arbre ou un poteau qui peuvent bouger au vent Probl me Le mouvement des arbres d clenche le d tecteur Solution Installer le d tecteur sur une surface stable 6 Le d tecteur a t il
74. f you require the sensor to operate both day and night turn the SUN MOON control knob clockwise to the sun and moon symbol 3 Check that lights from another source such as adjacent porch lights garden lights or street lights are not in the sensor s view The sen sor s photocell may detect the light and deactivate daylight If you desire the sensor to operate in higher ambient light levels turn the SUN MOON control knob counter clockwise toward the sun symbol 4 Was sensor wired hot If so circuitry may have been damaged Technical Tips Lights Do Not Turn On 20 safety zone TIME 12 MINS SENS TIME 12 MINS SENS 18 17 WRONG OK Zone de s curit de 20 pi Conseils techniques Les luminaires ne s allument pas 1 S assurer que tous les luminaires et lampes fonctionnent correctement Comparer le c blage au sch ma de raccordement dans ce manuel V rifier que les luminaires sont sous tension 2 Si l installation est effectu e le jour se rappeler que le d tecteur procure une p riode de test de 2 minutes apr s la mise sous tension Apr s 2 minutes le d tecteur passe en mode automatique et ne fonctionne pas le jour si la commande de photocellule est tourn e la position de nuit seulement symbole de lune Pour entreprendre une autre p riode de test de 2 minutes couper le courant pendant au moins 10 secondes puis le r tablir Si le d tecteur doit fon
75. ffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 BON MAUVAIS Installer e
76. for a weatherproof seal 9 Use silicone sealant around all openings to insure a weatherproof seal 10 Screw in light bulbs Turn on power Conduct walk test to adjust sensor response see page 15 Insert close up plug in unused hole Finishing Cap Metal Mounting Plate Bar Screws Gasket Universal Mounting Bar Gasket O Ring Gasket 8 Hook rests in notch on crossbar Hands Free Hanging Hook Black Black Red Red pigtail Ground Ground Power In White White Red pigtail is only used to switch remote or additional fixtures STL360H STL360Q2W STL360Q1 STL360Q3W STL360HBW CU4 EZ Plate Center Screw 7 CU4 EZ Plate Crochet mains libres Le crochet repose dans l encoche de la barre transversale Plaque CU4 EZ Plusieurs d tecteurs On peut raccorder plusieurs d tecteurs ensemble mais les probl mes sont alors difficiles corriger Les d tecteurs simples qui commandent leurs propres luminaires d tectent plus facilement le mouvement et facilitent le d pannage Plusieurs luminaires On peut raccorder plusieurs luminaires un seul d tecteur Un lectricien comp tent doit installer un relais afin de supporter les charges sup rieures 1 000 watts Qualit du courant On d conseille d installer les d tecteurs sur un circuit qui alimente aussi des charges moteur comme de l quipement de climatisation des appareils de cuisine ou des ouvre port
77. g Hook to hold the EZ Plate during wiring 3 Bring power leads and sensor kit leads through holes in all gaskets into junction box 4 Strip 1 2 of insulation from all leads 5 Attach ground wire s to junction box grounding screw Connect as shown in wiring diagram on page 7 6 Twist on wire nuts Secure with electrical tape 7 Align gaskets EZ Plate and metal mounting plate to insure proper seal Tighten EZ Plate center screw make sure O Ring gasket is on the screw to attach EZ Plate to the box 8 Insert plastic Finishing Cap in the center of the CU4 EZ Plate for a weatherproof seal 9 Use silicone sealant around all openings to insure a weatherproof seal 10 Screw in light bulbs Turn on power Conduct walk test to adjust sensor response see page 15 Insert close up plug in unused hole Finishing Cap Metal Mounting Plate Bar Screws Gasket Universal Mounting Bar Gasket O Ring Gasket 8 Hook rests in notch on crossbar Hands Free Hanging Hook Black Black Red Red pigtail Ground Ground Power In White White Red pigtail is only used to switch remote or additional fixtures STL360H STL360Q2W STL360Q1 STL360Q3W STL360HBW CU4 EZ Plate Center Screw 7 CU4 EZ Plate STL360 Assembly and Wiring To install a STL360 Sensor with separately purchased floodlights start at 1 To install STL360 Pre wired Floodlight Kits see page 7 1 Screw the
78. ghts stay on Lights remain on as long as there is movement within the protection zone Once the zone is vacated lights can be adjusted to remain on from approximately 5 seconds up to 12 minutes Since the lights are on only when needed and the sensor uses only one watt the STL360 is extremely energy efficient Can lights still be turned on with the light switch Yes STL360 can be controlled by a conventional indoor switch or circuit breaker The STL360 operates in Auto Mode unless changed The light can be turned on or off manually at night only see pages 13 14 for more info Manual Override Mode to keep lights on Flip the switch twice slowly off on off on within 1 2 secs Evening Timer to keep lights on for a set period each night Flip the switch three times slowly off on off on off on within 2 3 secs To Resume Auto Mode Switch power off for at least 10 seconds then back on Will STL360 detect animals STL360 may detect large animals Having animals trigger the sensor can give property a lived in look However you can limit animal detection by turning down the sensi tivity knob and or placing the blinders provided on the lower part of the forward lens How do you make adjustments to the sensor Use the adjustment tool provided or a screwdriver with a 1 8 wide blade to adjust the controls on the front of the sensor see page 11 12 2 On Guard Auto Mode LEDs scan continuously ba
79. he power is on 2 If installing during daylight remember that the sensor will provide 2 minutes of Test Time after power is turned on After 2 minutes the sensor will switch to Automatic Mode and will not work during day light if the photocell control is turned to the night only position moon symbol If you require 2 more minutes of Test Time turn the power off for at least 10 seconds and back on again If you require the sensor to operate both day and night turn the SUN MOON control knob clockwise to the sun and moon symbol 3 Check that lights from another source such as adjacent porch lights garden lights or street lights are not in the sensor s view The sen sor s photocell may detect the light and deactivate daylight If you desire the sensor to operate in higher ambient light levels turn the SUN MOON control knob counter clockwise toward the sun symbol 4 Was sensor wired hot If so circuitry may have been damaged Technical Tips Lights Do Not Turn On 20 safety zone TIME 12 MINS SENS TIME 12 MINS SENS 18 17 WRONG OK Conseils techniques Les luminaires s allument et s teignent incorrectement 1 Make sure the sensor is installed on its own dedicated circuit free of motor loads such as HVAC equipment kitchen appliances or garage door openers 2 It is not recommended to wire sensors in parallel More than one sensor wired together makes them difficu
80. heck that movement far away and directly towards sensor is not entirely within one zone Problem Sensor will not detect until movement crosses zones Solution Micro Adjust sensor by moving sideways 1 4 This may move the zones to allow earlier detection Technical Tips Range Appears Limited 20 40 Reduced Range 6 10 60 Maximum Range No detection until here Detection here now Less Sensitive More Sensitive 20 19 Replacement Lamps STL360Q1 150 watt double ended quartz flood STL360Q2 2 lamps 150 watt double ended quartz flood STL360Q3 300 watt double ended quartz flood STL360H 2 lamps 150 watt PAR38 STL360HB 2 lamps 150 watt PAR38 NOTE All double ended quartz fixtures must be mounted with the lamp horizontal or parallel to the ground If the fixture is tilted the lamp will fail prematurely Limited Warranty Your STL360 will be replaced or repaired at our option if it proves to be defective in workmanship or materials within ten years from the date of original purchase For repair replacement return the product freight prepaid and insured to RC Lighting 170 Ludlow Avenue Northvale NJ 07647 The STL360 should be packed carefully Please include your sales receipt and a description of the problem Ifyourunitisoutofwarranty orthedamageisunrelatedtothe original manufacture return your unit directly to us with a check for 30 00 made out to RC Electric We w
81. hs of movement The sensor may be wall or soffit mounted As distance from the sensor increases larger movement will be required for detection For instance at 10 feet a half step will be enough while at 50 feet several steps will be necessary for detection How large an area does STL360 protect Two powerful detectors combine to give the STL360 180 x 60 long forward range plus superb 360 downward detection below and to all sides Mounting Height Mounting at 6 12 above the ground allows maximum range If the sensor is mounted above 15 high the usable range is reduced Location Tips Difficult Locations Sensor may be triggered by unwanted movement or heat source such as a swaying tree road traffic dryer vent swimming pool or hot tub To Improve Performance in Difficult Locations Reduce sensitivity by turning the SENS knob counterclockwise and or Mask lens in the direction of the unwanted movement or heat source using the lens mask provided or opaque tape Mounting Stability Mount sensor on stable surface Do not mount on a tree or pole that will move in the wind Make sure sensor and lights are mounted firmly If they move when touched tighten all screws Light vs Sensor Position Make sure heat from lights is not triggering sensor Sensor must be located below and as far away as possible from its lights STL360Q1 STL360Q2 amp STL360Q3 Kits Mount only on non com
82. ide to side 2 Check that the sensor is not mount ed too high If mounted above 20 feet much of the usable range will be lost Solution Mounting at 6 feet to 10 feet allows maximum range 3 Check that movement is not directly towards sensor Sensor will see movement across its pattern more quickly To fix move the sensor 4 Check that movement far away and directly towards sensor is not entirely within one zone Problem Sensor will not detect until movement crosses zones Solution Micro Adjust sensor by moving sideways 1 4 This may move the zones to allow earlier detection Technical Tips Range Appears Limited 20 40 Reduced Range 6 10 60 Maximum Range No detection until here Detection here now Less Sensitive More Sensitive 20 19 Technical Tips Lights Turn Off Too Quickly 1 Check if sensor is being tricked by reflected light If lights controlled by the sensor shine or reflect into the photocell locat ed behind the lens the unit will go on briefly see its own light and turn off thinking that it is daytime Problems Lights reflect into photocell Lights shine directly into photocell Solution Adjust SUN MOON knob slightly clockwise to allow operation at higher ambient light levels Alternatively move the lights or reflectors or mask the lens in the direction of the lights and or reflections 2 Check if R lamps non reflector A
83. if sensor is being tricked by reflected light If lights controlled by the sensor shine or reflect into the photocell locat ed behind the lens the unit will go on briefly see its own light and turn off thinking that it is daytime Problems Lights reflect into photocell Lights shine directly into photocell Solution Adjust SUN MOON knob slightly clockwise to allow operation at higher ambient light levels Alternatively move the lights or reflectors or mask the lens in the direction of the lights and or reflections 2 Check if R lamps non reflector A lamps or self ballasted PL lamps are being used in a non enclosed lampholder If so switch to reflector PAR floodlight lamps or Quartz floods so the sensor is not affected by stray light If using PAR floodlights con sider using lower wattage energy saving lamps TIME 12 MINS SENS OK WRONG 1 Check that the sensor is level from side to side and pointed at the area you desire If unit is tilted part of the detection zone may be high in the air over people s heads Solution Position sensor exactly level from side to side 2 Check that the sensor is not mount ed too high If mounted above 20 feet much of the usable range will be lost Solution Mounting at 6 feet to 10 feet allows maximum range 3 Check that movement is not directly towards sensor Sensor will see movement across its pattern more quickly To fix move the
84. ighting 170 Ludlow Avenue Northvale New Jersey 07647 U S A RAB Lighting 2004 Incorrect Correct 22 21 Garantie limit e Le STL360 sera remplac ou r par notre discr tion s il est jug comporter des d fauts de main d uvre ou de mat riaux dans les dix ann es qui suivent la date d achat originale Pour obtenir une r paration ou un remplacement retourner le produit port pay et assur RC Lighting 170 Ludlow Av enue Northvale NJ 07647 Le STL360 doit tre emball avec soin Pri re d inclure le coupon de caisse et une description du probl me Si l unit n est plus prot g e par la garantie ou que les dommages ne sont pas reli s sa fabrication originale nous retourner l unit directement accompagn e d un ch que de 30 00 l ordre de RC Lighting Nous r parerons ou remplacerons votre unit Nous ne pourrons tre tenus responsables en aucun cas des dommages accidentels ou accessoires d coulant de l utilisation ou du rendement de ce produit ou d autres dommages indirects relativement la perte de propri t ou de revenus ou aux co ts d installation de retrait ou de r installation La pr sente garan tie vous conf re des droits l gaux pr cis et vous pouvez avoir d autres droits qui varient d une province l autre Contenu de la trousse d accessoires Replacement Lamps STL360Q1 150 watt double ended quartz flood STL360Q2 2 lamps 150 watt
85. ill repair or replace your unit Under no circumstances shall we be liable for any incidental or consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property or revenue or cost of installation removal or re installation This warranty gives you specific legal rights and you may also have other rights which vary from state to state Contents of Accessory Kit 2 Lens Masks Indoor Switchplate Label 3 Wire Nuts Adjustment Tool Mylar Lens Mask Crossbar with Green Ground Screw Hanging Hook 1 2 Close Up Plugs 3 Slotted Screws 4 Finishing Cap O ring Gasket Center Mounting Screw Foam Gaskets 2 Metal Plate Incorrect Correct 22 21 Toll free fax e mail Send a fax to 888 722 1232 Tech Help Line Call our experts 888 722 1000 Visit our website for product info EasyAnswers rclighting ca Get answers promptly sales rclighting ca The designs of RC Lighting fixtures are protected under Canadian U S and international intellectual property laws 2010 RC Lighting NOTE THESE INSTRUCTIONS DO NOT COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT NOR DO THEY PROVIDE FOR EVERY POSSIBLE SITUATION DURING INSTALLATION OPERATION OR MAINTENANCE Specifications Switching Capacity 8 amps 1000 watts Incandescent and 250 watts Fluorescent Voltage 120 volts
86. ing tricked by reflected light If lights controlled by the sensor shine or reflect into the photocell locat ed behind the lens the unit will go on briefly see its own light and turn off thinking that it is daytime Problems Lights reflect into photocell Lights shine directly into photocell Solution Adjust SUN MOON knob slightly clockwise to allow operation at higher ambient light levels Alternatively move the lights or reflectors or mask the lens in the direction of the lights and or reflections 2 Check if R lamps non reflector A lamps or self ballasted PL lamps are being used in a non enclosed lampholder If so switch to reflector PAR floodlight lamps or Quartz floods so the sensor is not affected by stray light If using PAR floodlights con sider using lower wattage energy saving lamps TIME 12 MINS SENS OK WRONG 1 Check that the sensor is level from side to side and pointed at the area you desire If unit is tilted part of the detection zone may be high in the air over people s heads Solution Position sensor exactly level from side to side 2 Check that the sensor is not mount ed too high If mounted above 20 feet much of the usable range will be lost Solution Mounting at 6 feet to 10 feet allows maximum range 3 Check that movement is not directly towards sensor Sensor will see movement across its pattern more quickly To fix move the sensor 4 C
87. ion Manual Manuel d installation Le STEALTH360 est le syst me d clairage command par le mouvement le pus fiable et le plus technologique ment avanc jamais produit Ce manuel technique s adresse aux professionnels de l lectricit qui veulent maximiser le rendement et la fiabilit de ce superbe d tecteur RC Lighting vous incite soumettre aux questions ou commentaires en appelant au 888 722 1000 ou par courriel Merci d avoir achet un d tecteur RC Lighting Specifications Switching Capacity 8 amps 1000 watts Incandescent and 250 watts Fluorescent Voltage 120 volts Protection Pattern 180 forward 360 below and to all sides Time Adjustment 5 seconds to 12 minutes Power Consumption 1 watt Surge protection 6000 volts Cautions TURN OFF ALL POWER AT CIRCUIT BREAKER FUSE PANEL Read entire Installation Manual before proceeding All wiring should comply with local electrical codes and requires a qualified electrician The total lighting load connected to STL360 must not exceed 1000 watts incandescent or quartz 250 watts fluorescent To switch more wattage an electrician can install a relay Line Carrier Remote Control Systems such as X 10 Leviton or Radio Shack are incompatible with sensors and may cause false activations Do not install sensors on a circuit that feeds motor loads such as kitchen appliances HVAC equipment washer dryer or garage door openers Sensor func
88. ion jusqu ce point D tection ici maintenant VOIE D ACC S VOIE D ACC S Replacement Lamps STL360Q1 150 watt double ended quartz flood STL360Q2 2 lamps 150 watt double ended quartz flood STL360Q3 300 watt double ended quartz flood STL360H 2 lamps 150 watt PAR38 STL360HB 2 lamps 150 watt PAR38 NOTE All double ended quartz fixtures must be mounted with the lamp horizontal or parallel to the ground If the fixture is tilted the lamp will fail prematurely Limited Warranty Your STL360 will be replaced or repaired at our option if it proves to be defective in workmanship or materials within ten years from the date of original purchase For repair replacement return the product freight prepaid and insured to RAB Lighting 170 Ludlow Avenue Northvale NJ 07647 The STL360 should be packed carefully Please include your sales receipt and a description of the problem If your unit is out of warranty or the damage is unrelated to the original manufacture return your unit directly to us with a check for 20 00 made out to RAB Electric We will repair or replace your unit Under no circumstances shall we be liable for any incidental or consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property or revenue or cost of installation removal or re installation This warranty gives you specific legal rights and you may a
89. its lights Heat from the lights may trigger the sensor Solution Move sensor below and away from the lights 5 Make sure lights are not reflecting back into sensor Check for white or reflective surfaces close to the sensor Solution Aim sensor away from reflective objects or move the objects and lower sensitivity 6 Make sure sensor is not aimed within 20 feet of a road or sidewalk Passing cars will activate sensor Solution A 20 foot safety zone and reduced sensitivity are recommended to avoid activation from passing cars 7 Heavy rain snow or high winds may activate the sensor occasionally Reduce sensitivity control slightly until problem stops 8 Moths can be attracted to the lights and fly close to the sensor causing triggering Reducing the sensitivity may help 9 Check Solutions 3 4 5 6 7 and 8 under If Lights Do Not Turn Off Technical Tips Lights Turn On and Off Inappropriately 1 Check that lamps and fixtures work Compare wiring to the wiring diagram in this manual Check that the power is on 2 If installing during daylight remember that the sensor will provide 2 minutes of Test Time after power is turned on After 2 minutes the sensor will switch to Automatic Mode and will not work during day light if the photocell control is turned to the night only position moon symbol If you require 2 more minutes of Test Time turn the power off for at least 10 seconds and back on again I
90. k rests in notch on crossbar Hands Free Hanging Hook Black Black Red Red pigtail Ground Ground Power In White White Red pigtail is only used to switch remote or additional fixtures STL360H STL360Q2W STL360Q1 STL360Q3W STL360HBW CU4 EZ Plate Center Screw 7 CU4 EZ Plate STL360 Kit Assembly and Wiring STL360 floodlight kits come pre wired and assembled on the RAB CU4 EZ plate allowing for mounting on round rectangular or octagonal surface or recessed boxes Mounting Wiring STL360 Kit Assembly and Wiring 1 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 2 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 3 Bring power leads and sensor kit leads through holes in all gaskets into junction box 4 Strip 1 2 of insulation from all leads 5 Attach ground wire s to junction box grounding screw Connect as shown in wiring diagram on page 7 6 Twist on wire nuts Secure with electrical tape 7 Align gaskets EZ Plate and metal mounting plate to insure proper seal Tighten EZ Plate center screw make sure O Ring gasket is on the screw to attach EZ Plate to the box 8 Insert plastic Finishing Cap in the center of the CU4 EZ Plate
91. ked by reflected light If lights controlled by the sensor shine or reflect into the photocell locat ed behind the lens the unit will go on briefly see its own light and turn off thinking that it is daytime Problems Lights reflect into photocell Lights shine directly into photocell Solution Adjust SUN MOON knob slightly clockwise to allow operation at higher ambient light levels Alternatively move the lights or reflectors or mask the lens in the direction of the lights and or reflections 2 Check if R lamps non reflector A lamps or self ballasted PL lamps are being used in a non enclosed lampholder If so switch to reflector PAR floodlight lamps or Quartz floods so the sensor is not affected by stray light If using PAR floodlights con sider using lower wattage energy saving lamps TIME 12 MINS SENS OK WRONG 1 Check that the sensor is level from side to side and pointed at the area you desire If unit is tilted part of the detection zone may be high in the air over people s heads Solution Position sensor exactly level from side to side 2 Check that the sensor is not mount ed too high If mounted above 20 feet much of the usable range will be lost Solution Mounting at 6 feet to 10 feet allows maximum range 3 Check that movement is not directly towards sensor Sensor will see movement across its pattern more quickly To fix move the sensor 4 Check that m
92. ket 8 Hook rests in notch on crossbar Hands Free Hanging Hook Black Black Red Red pigtail Ground Ground Power In White White Red pigtail is only used to switch remote or additional fixtures STL360H STL360Q2W STL360Q1 STL360Q3W STL360HBW CU4 EZ Plate Center Screw 7 CU4 EZ Plate Les trousses de projecteurs STL360 sont pr c bl es et assembl es sur la plaque RC Lighting CU4 EZ permet tant le montage sur les surfaces rondes rectangulaires ou octogonales ou dans les bo tes encastr es Montage C blage STL360 Kit Assembly and Wiring STL360 floodlight kits come pre wired and assembled on the RAB CU4 EZ plate allowing for mounting on round rectangular or octagonal surface or recessed boxes Mounting Wiring STL360 Kit Assembly and Wiring 1 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 2 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 3 Bring power leads and sensor kit leads through holes in all gaskets into junction box 4 Strip 1 2 of insulation from all leads 5 Attach ground wire s to junction box grounding screw Connect as shown in wiring diagram on page 7 6 Twist on wire nuts Secure with electrical t
93. kits come pre wired and assembled on the RAB CU4 EZ plate allowing for mounting on round rectangular or octagonal surface or recessed boxes Mounting Wiring STL360 Kit Assembly and Wiring 1 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 2 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 3 Bring power leads and sensor kit leads through holes in all gaskets into junction box 4 Strip 1 2 of insulation from all leads 5 Attach ground wire s to junction box grounding screw Connect as shown in wiring diagram on page 7 6 Twist on wire nuts Secure with electrical tape 7 Align gaskets EZ Plate and metal mounting plate to insure proper seal Tighten EZ Plate center screw make sure O Ring gasket is on the screw to attach EZ Plate to the box 8 Insert plastic Finishing Cap in the center of the CU4 EZ Plate for a weatherproof seal 9 Use silicone sealant around all openings to insure a weatherproof seal 10 Screw in light bulbs Turn on power Conduct walk test to adjust sensor response see page 15 Insert close up plug in unused hole Finishing Cap Metal Mounting Plate Bar Screws Gasket Universal Mounting Bar Gasket O Ring Gasket 8 Hoo
94. l may detect the light and deactivate daylight If you desire the sensor to operate in higher ambient light levels turn the SUN MOON control knob counter clockwise toward the sun symbol 4 Was sensor wired hot If so circuitry may have been damaged Technical Tips Lights Do Not Turn On 20 safety zone TIME 12 MINS SENS TIME 12 MINS SENS 18 17 WRONG OK 1 Make sure the sensor is installed on its own dedicated circuit free of motor loads such as HVAC equipment kitchen appliances or garage door openers 2 It is not recommended to wire sensors in parallel More than one sensor wired together makes them difficult to troubleshoot Disconnect multi ple sensors and test separately 3 Keep all people completely out of the detection pattern to make sure the sensor is not detecting them 4 Make sure sensor is located below and as far as possible from its lights Heat from the lights may trigger the sensor Solution Move sensor below and away from the lights 5 Make sure lights are not reflecting back into sensor Check for white or reflective surfaces close to the sensor Solution Aim sensor away from reflective objects or move the objects and lower sensitivity 6 Make sure sensor is not aimed within 20 feet of a road or sidewalk Passing cars will activate sensor Solution A 20 foot safety zone and reduced sensitivity are recommended to avoid activation from passing cars
95. lso have other rights which vary from state to state Contents of Accessory Kit 2 Lens Masks Indoor Switchplate Label 3 Wire Nuts Adjustment Tool Mylar Lens Mask Crossbar with Green Ground Screw Hanging Hook 1 2 Close Up Plugs 3 Slotted Screws 4 Finishing Cap O ring Gasket Center Mounting Screw Foam Gaskets 2 Metal Plate MAKES IT EASY Easy Installation amp Product Help Toll Free Phone Toll Free Fax Fax on Demand Call our friendly experts Send faxes to RAB Faxed information 8AM 6PM ET Mon Fri 24 7 24 7 888 RAB 1000 888 RAB 1232 888 RAB 1236 E mail www rabweb com Questions and requests Visit our internet site answered promptly for product information tech rabweb com RAB Lighting 170 Ludlow Avenue Northvale New Jersey 07647 U S A RAB Lighting 2004 Incorrect Correct 22 21 Lampes de rechange Replacement Lamps STL360Q1 150 watt double ended quartz flood STL360Q2 2 lamps 150 watt double ended quartz flood STL360Q3 300 watt double ended quartz flood STL360H 2 lamps 150 watt PAR38 STL360HB 2 lamps 150 watt PAR38 NOTE All double ended quartz fixtures must be mounted with the lamp horizontal or parallel to the ground If the fixture is tilted the lamp will fail prematurely Limited Warranty Your STL360 will be replaced or repaired at our option if it proves to be defective in workmanship or material
96. lt to troubleshoot Disconnect multi ple sensors and test separately 3 Keep all people completely out of the detection pattern to make sure the sensor is not detecting them 4 Make sure sensor is located below and as far as possible from its lights Heat from the lights may trigger the sensor Solution Move sensor below and away from the lights 5 Make sure lights are not reflecting back into sensor Check for white or reflective surfaces close to the sensor Solution Aim sensor away from reflective objects or move the objects and lower sensitivity 6 Make sure sensor is not aimed within 20 feet of a road or sidewalk Passing cars will activate sensor Solution A 20 foot safety zone and reduced sensitivity are recommended to avoid activation from passing cars 7 Heavy rain snow or high winds may activate the sensor occasionally Reduce sensitivity control slightly until problem stops 8 Moths can be attracted to the lights and fly close to the sensor causing triggering Reducing the sensitivity may help 9 Check Solutions 3 4 5 6 7 and 8 under If Lights Do Not Turn Off Technical Tips Lights Turn On and Off Inappropriately 1 Check that lamps and fixtures work Compare wiring to the wiring diagram in this manual Check that the power is on 2 If installing during daylight remember that the sensor will provide 2 minutes of Test Time after power is turned on After 2 minutes the sensor will swi
97. ly purchased floodlights start at 1 To install STL360 Pre wired Floodlight Kits see page 7 1 Screw the threaded arms of each floodlight into the RAB CU4 EZ Plate See diagram on page 7 2 Screw the threaded arm of the sensor into the bottom hole of the EZ Plate Sensor should be below and as far away from the floodlights as possible 3 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 4 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 5 Bring power leads light fixture and sensor leads through holes in all gaskets and mounting plates into junction box 6 Attach ground wire s to junction box grounding screw 7 Position EZ Plate gaskets and metal plate see pg 7 8 Strip 1 2 of insulation from all leads Connect as shown in wiring diagram 9 Twist on wire nuts Secure with electrical tape 10 Make sure all unused openings in EZ Plate are closed with plugs provided 11 Screw in light bulbs Turn on power 12 Conduct Walk Test to adjust sensor response see page 15 STL360 Assembly and Wiring Multiple Sensors Multiple sensors may be wired together but doing this will make problems difficult to troubleshoot Single sensors that control their own lights will gi
98. m its lights STL360Q1 STL360Q2 amp STL360Q3 Kits Mount only on non combustible surfaces Side View 6 10 wrong wrong OK TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 20 40 6 10 60 Reduced Range Maximum Range mask 4 3 60 60 20 MINUTERIE DE SOIR E MINUTERIE Choosing a Location The best location is where the sensor can see all paths of movement The sensor may be wall or soffit mounted As distance from the sensor increases larger movement will be required for detection For instance at 10 feet a half step will be enough while at 50 feet several steps will be necessary for detection How large an area does STL360 protect Two powerful detectors combine to give the STL360 180 x 60 long forward range plus superb 360 downward detection below and to all sides Mounting Height Mounting at 6 12 above the ground allows maximum range If the sensor is mounted above 15 high the usable range is reduced Location Tips Difficult Locations Sensor may be triggered by unwanted movement or heat source such as a swaying tree road traffic dryer vent swimming pool or hot tub To Improve Performance in Difficult Locations Reduce sensitivity by turning the SENS knob counterclockwise and or Mask lens in the direction of the unwanted movement or heat source using the lens mask provided or opaque tape M
99. mal motion activated lighting The EVENING TIMER can keep lights on continuously without motion for 1 to 8 hours after dusk This is great for evening activities requiring continuous light During vacations the EVENING TIMER provides a lived in look by simulating an occupant turning lights on at dusk and then off at bedtime To set the EVENING TIMER flip the wall switch controlling the sensor three times slowly off on off on off on within 3 seconds If you set the EVENING TIMER during daytime the middle LED should start blinking indicating that the Evening Timer will start when dusk is detected Choose the length of time you want continuous lighting For example if you set the EVENING TIMER to 8 the sensor will keep lights ON continuously for 8 hours after dusk Once 8 hours have passed the sensor will revert to motion activated mode At dawn the photocell will detect light and prevent lights from turning on during the daytime If you do not want to use the EVENING TIMER do NOT flip the switch 3 times as described above To end use of the EVENING TIMER switch OFF the power for at least 10 seconds then ON again Sensor will be in Automatic Mode After completing the warm up period You can affix this label right provided to your indoor light switch plate for easy reference 12 TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING
100. n its protection zone and turns on lights automatically It welcomes visitors and may deter intruders Total coverage Two sensors in one Two powerful detectors combine to give the STL360 Can t Miss Detection 180 long forward range 180 x 60 plus superb 360 detection below and to all sides How do the scanning LED detection indicators work Scanning LEDs serve as a deterrent by indicating a securi ty device in operation They also show the STL360 s mode of operation On Guard When the STL360 is On Guard in Auto mode three red LEDs scan continu ously day and night except during detections at which time the controlled lights will go on Test Mode When the sensor is in Test Mode all the LEDs will be off If the sensor is set for night only operation the LED stays On Guard daytime detections do not turn on the lights Manual Override Mode In Manual Override Mode the middle LED will be on see page 14 Howhe SuperSTL360 360 Work How Does the Super Stealth 360 Work How long do the lights stay on Lights remain on as long as there is movement within the protection zone Once the zone is vacated lights can be adjusted to remain on from approximately 5 seconds up to 12 minutes Since the lights are on only when needed and the sensor uses only one watt the STL360 is extremely energy efficient Can lights still be turned on with the light switch Yes STL360 can be c
101. n fonction du mouvement dans la zone prot g e V rifier que le mouvement n est pas dirig directement vers le d tecteur Le d tecteur verra le mouvement plus rapidement sur TOUTE sa zone V rifier que le mouvement loign et directement en direction du d tecteur ne se trouve pas compl tement l int rieur d une zone Pour corriger changer l emplacement du d tecteur Si le d tecteur est install au dessus d une voie d acc s vers laquelle tout le mouvement est dirig la port e peut para tre limit e Micro ajuster le d tec teur en le bougeant d environ 1 4 po gauche ou droite pour repositionner les zones suffisam ment pour permettre la d tection plus rapide Choisir un endroit prot g Installer le d tecteur dans un endroit prot g Plus l endroit d installation est prot g moins les luminaires courent la chance d tre allum s l occasion en cas de pluie de neige ou de temp te de vent parce que le d tecteur d tecte les changements consid rables de temp rature Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make s
102. n for a set period each night Flip the switch three times slowly off on off on off on within 2 3 secs To Resume Auto Mode Switch power off for at least 10 seconds then back on Will STL360 detect animals STL360 may detect large animals Having animals trigger the sensor can give property a lived in look However you can limit animal detection by turning down the sensi tivity knob and or placing the blinders provided on the lower part of the forward lens How do you make adjustments to the sensor Use the adjustment tool provided or a screwdriver with a 1 8 wide blade to adjust the controls on the front of the sensor see page 11 12 2 On Guard Auto Mode LEDs scan continuously back amp forth Ready for Manual Override Mode Middle LED on Test Mode All LEDs off controls TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 1 Pendant combien de temps l clairage reste il allum Les lumi res restent allum es aussi longtemps que le mouve ment est d tect dans la zone de protection Une fois la zone lib r e on peut r gler les luminaires de mani re rester al lumer entre 5 secondes et 12 minutes Comme les luminaires s allument seulement au besoin et que le d tecteur consomme seulement un watt le STL360 est extr mement conome d nergie Est ce que les lampes peuvent tout de m me tre allum es par l interrupteur Oui Le STL360 peut tre comm
103. n off on off on within 3 seconds If you set the EVENING TIMER during daytime the middle LED should start blinking indicating that the Evening Timer will start when dusk is detected Choose the length of time you want continuous lighting For example if you set the EVENING TIMER to 8 the sensor will keep lights ON continuously for 8 hours after dusk Once 8 hours have passed the sensor will revert to motion activated mode At dawn the photocell will detect light and prevent lights from turning on during the daytime If you do not want to use the EVENING TIMER do NOT flip the switch 3 times as described above To end use of the EVENING TIMER switch OFF the power for at least 10 seconds then ON again Sensor will be in Automatic Mode After completing the warm up period You can affix this label right provided to your indoor light switch plate for easy reference 12 TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 11 PHOTOCELLULE MINUTERIE DE SOIR E MINUTERIE MINUTERIE DE SOIR E MINUTERIE MINUTERIE DE SOIR E MINUTERIE MINUTERIE DE SOIR E MINUTERIE Adjusting the Settings TIME Sets the time that lights will remain on after the detection zone is vacated Adjustabl
104. nd back on again In Test Mode no LEDs are lit MANUAL OVERRIDE MODE The STL360 has a protected Manual Override that requires a double flip of the light switch so momentary power problems do not interfere with normal sensor operation By flipping the switch that operates the sensor twice off on off on within 2 seconds you will override the sensor to keep lights on continuously until dawn If you set the Manual Override Mode during daylight the sensor will be prepared to turn on at dusk and remain on until dawn This is a handy feature if you leave home for the day and you want the lights on to greet you when you return When the sensor is in Ready for Manual Override Mode the middle LED will be on TO RESUME AUTOMATIC MODE Switch OFF the power for at least 10 seconds then turn it ON again Sensor will reset to Automatic Mode after completing the warm up period and Test Mode 14 On Guard Auto Mode LEDs scan continuously back and forth Ready for Manual Override Mode Middle LED on Ready for Evening Timer Mode Middle LED blinks 13 DAYTIME 24 HOUR OPERATION OF MANUAL OVERRIDE If you set Manual Override while set to 24 hour operation lights will come on and remain on continuosly Lights will not turn off at dawn Walk Testing STL360 s full coverage pattern reduces the need for aiming and adjustment The purpose of the Walk Test is to check and adjust the coverage pattern The STL360 h
105. nd lower sensitivity are recommended to avoid activation from passing cars 8 Make sure heat from lights is not triggering sensor Make sure the sensor is below and as far as possible away from sensor 16 20 safety zone OK 15 Test de marche La configuration de couverture compl te du STL360 r duit la n cessit d orienter et de r gler l appareil Le test de marche permet de v rifier et de r gler la configuration de couverture La p riode de test du STL360 permet v rifier le d tecteur en effectuant un test de marche jour ou nuit Pour passer en mode Test 1 Le d tecteur est en mode test la mise sous tension initiale Couper le courant pendant au moins 10 secondes puis le r tablir Diriger le d tecteur vers la zone de circulation d tecter Le d tecteur d tecte le mouvement plus efficacement AU TRAVERS de sa configuration 2 P n trer dans la zone de d tection et marcher l int rieur de la zone jusqu ce que les luminaires s allument Plus la distance par rapport au d tecteur augmente plus le mouvement est difficile d tecter 3 Ajuster la position du d tecteur au besoin pour am liorer la couverture S assurer que le d tecteur est de niveau 4 On peut r duire la sensibilit l aide du bouton SENS afin de d tecter une zone limit e ou sui le d tecteur est d clench par le vent les feuilles la circulation ou les animaux ou l augmenter pour prot ge
106. nd passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning
107. ng LED detection indicators work Scanning LEDs serve as a deterrent by indicating a securi ty device in operation They also show the STL360 s mode of operation On Guard When the STL360 is On Guard in Auto mode three red LEDs scan continu ously day and night except during detections at which time the controlled lights will go on Test Mode When the sensor is in Test Mode all the LEDs will be off If the sensor is set for night only operation the LED stays On Guard daytime detections do not turn on the lights Manual Override Mode In Manual Override Mode the middle LED will be on see page 14 Howhe SuperSTL360 360 Work How Does the Super Stealth 360 Work How long do the lights stay on Lights remain on as long as there is movement within the protection zone Once the zone is vacated lights can be adjusted to remain on from approximately 5 seconds up to 12 minutes Since the lights are on only when needed and the sensor uses only one watt the STL360 is extremely energy efficient Can lights still be turned on with the light switch Yes STL360 can be controlled by a conventional indoor switch or circuit breaker The STL360 operates in Auto Mode unless changed The light can be turned on or off manually at night only see pages 13 14 for more info Manual Override Mode to keep lights on Flip the switch twice slowly off on off on within 1 2 secs Evening Timer to keep lights o
108. ntrol Systems such as X 10 Leviton or Radio Shack are incompatible with sensors and may cause false activations Do not install sensors on a circuit that feeds motor loads such as kitchen appliances HVAC equipment washer dryer or garage door openers Sensor functions best when the direction of expected movement is across its detection pattern not towards the sensor Mount 6 12 high for optimum range and detection The STEALTH360 is the most reliable and technically advanced motion activated light control ever produced This techni cal manual is written for electrical professionals who wish to maximize the performance and reliability of this superb sensor RAB welcomes your questions or comments Please call 888 722 1000 or email tech rabweb com Thank you for purchasing a RAB sensor STL360H STL360HBW STL360Q1 STL360Q3W STL360Q2W Installation Manual Specifications Switching Capacity 8 amps 1000 watts Incandescent and 250 watts Fluorescent Voltage 120 volts Protection Pattern 180 forward 360 below and to all sides Time Adjustment 5 seconds to 12 minutes Power Consumption 1 watt Surge protection 6000 volts Cautions TURN OFF ALL POWER AT CIRCUIT BREAKER FUSE PANEL Read entire Installation Manual before proceeding All wiring should comply with local electrical codes and requires a qualified electrician The total lighting load connected to STL360 must not exceed 1000 wa
109. of sensor Lights should go on and then time out If sensor operates properly when covered check items 4 8 Problem Sensor is triggered by unwanted movement or heat source Solution 1 Aim sensor away from movement or 2 Mask lens as in the direction of the source 3 Lower sensitivity control setting 4 Make sure sensor and lights are mounted firmly and do not move even slightly when touched If they move tighten all screws 5 Make sure sensor is not mounted on an unstable object such as a tree or pole that will move in the wind Problem Movement of tree triggers sensor Solution Mount on stable surface 6 Was sensor wired hot If so circuitry may have been damaged 7 Make sure sensor is not aimed within 20 feet of a road Problem Passing cars activate sensor Solution A 20 foot safety zone and lower sensitivity are recommended to avoid activation from passing cars 8 Make sure heat from lights is not triggering sensor Make sure the sensor is below and as far as possible away from sensor 16 20 safety zone OK 15 Conseils techniques L clairage ne s teint pas 1 S assurer que le d tecteur n est pas en mode Contournement manuel Couper le courant pendant 10 secondes puis le r tablir pour passer en mode test pendant environ 2 minutes puis en mode automatique avec luminaires teints et pr ts d tecter le mouvement 2 S assurer que le d tecteur n est pas en mode minut
110. onds then ON Sensor will be in Test Mode for approximately 2 minutes then it will switch to Auto Mode with lights off and ready to detect movement 2 Make sure that the sensor is not in Evening Timer Mode Turn power OFF for 10 seconds see 1 3 Make sure sensor is not aimed at or mounted over something that would move or change temperature such as waving branches water air condi tioners windows or heating vents even on neighboring property You can test for infrared sources in the area by placing a box or bag over the sensor Put sensor into test mode Lights should stay off Wave your hand inside bag in front of sensor Lights should go on and then time out If sensor operates properly when covered check items 4 8 Problem Sensor is triggered by unwanted movement or heat source Solution 1 Aim sensor away from movement or 2 Mask lens as in the direction of the source 3 Lower sensitivity control setting 4 Make sure sensor and lights are mounted firmly and do not move even slightly when touched If they move tighten all screws 5 Make sure sensor is not mounted on an unstable object such as a tree or pole that will move in the wind Problem Movement of tree triggers sensor Solution Mount on stable surface 6 Was sensor wired hot If so circuitry may have been damaged 7 Make sure sensor is not aimed within 20 feet of a road Problem Passing cars activate sensor Solution A 20 foot safety zone a
111. ontrolled by a conventional indoor switch or circuit breaker The STL360 operates in Auto Mode unless changed The light can be turned on or off manually at night only see pages 13 14 for more info Manual Override Mode to keep lights on Flip the switch twice slowly off on off on within 1 2 secs Evening Timer to keep lights on for a set period each night Flip the switch three times slowly off on off on off on within 2 3 secs To Resume Auto Mode Switch power off for at least 10 seconds then back on Will STL360 detect animals STL360 may detect large animals Having animals trigger the sensor can give property a lived in look However you can limit animal detection by turning down the sensi tivity knob and or placing the blinders provided on the lower part of the forward lens How do you make adjustments to the sensor Use the adjustment tool provided or a screwdriver with a 1 8 wide blade to adjust the controls on the front of the sensor see page 11 12 2 On Guard Auto Mode LEDs scan continuously back amp forth Ready for Manual Override Mode Middle LED on Test Mode All LEDs off controls TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 1 commandes How Does the Super Stealth 360 Work The STL360 s infrared sensor sees temperature changes caused by the motion of people or cars within its protection zone and turns on lights automatically It wel
112. ors on a circuit that feeds motor loads such as kitchen appliances HVAC equipment washer dryer or garage door openers Sensor functions best when the direction of expected movement is across its detection pattern not towards the sensor Mount 6 12 high for optimum range and detection The STEALTH360 is the most reliable and technically advanced motion activated light control ever produced This techni cal manual is written for electrical professionals who wish to maximize the performance and reliability of this superb sensor RAB welcomes your questions or comments Please call 888 722 1000 or email tech rabweb com Thank you for purchasing a RAB sensor STL360H STL360HBW STL360Q1 STL360Q3W STL360Q2W Installation Manual Specifications Switching Capacity 8 amps 1000 watts Incandescent and 250 watts Fluorescent Voltage 120 volts Protection Pattern 180 forward 360 below and to all sides Time Adjustment 5 seconds to 12 minutes Power Consumption 1 watt Surge protection 6000 volts Cautions TURN OFF ALL POWER AT CIRCUIT BREAKER FUSE PANEL Read entire Installation Manual before proceeding All wiring should comply with local electrical codes and requires a qualified electrician The total lighting load connected to STL360 must not exceed 1000 watts incandescent or quartz 250 watts fluorescent To switch more wattage an electrician can install a relay Line Carrier Remote Co
113. otected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6 5 MAUVAIS BON Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor will see movement ACROSS its pattern
114. ouble actionnement de l interrupteur pour que les probl mes d alimentation mo mentan s ne perturbent pas le fonctionnement normal du d tecteur En actionnant l interrupteur qui commande le d tecteur deux fois arr t marche arr t marche en 2 secondes on peut contourner le d tecteur de mani re garder les lumi naires allum s en permanence jusqu l aube Si le mode contournement manuel est programm le jour le d tecteur est pr t allumer les luminaires du cr puscule l aube Cette fonction s av re pratique si on doit quitter la maison pour la journ e et tre accueilli par des luminaires allum s au retour La D L du centre est allum e quand le d tecteur est Pr t pour le mode contournement manuel POUR REPRENDRE LE MODE AUTOMATIQUE Couper le courant pendant au moins 10 secondes puis le r tablir Le d tecteur r tablit le mode automatique apr s la p riode d chauffement et le mode test FONCTIONNEMENT DE JOUR 24 HEURES DU CONTOURNEMENT MANUEL Si le contournement manuel est programm en mode de fonctionnement 24 heures les luminaires s allument et rest ent allum s en permanence Les luminaires ne s teignent pas l aube Modes de d tecteur MODE AUTOMATIQUE Les luminaires s allument en cas de mouvement dans la zone de d tection apr s le cr puscule Sensor Modes AUTOMATIC MODE Lights will turn on when there is movement with in the detection zone aft
115. ounting Stability Mount sensor on stable surface Do not mount on a tree or pole that will move in the wind Make sure sensor and lights are mounted firmly If they move when touched tighten all screws Light vs Sensor Position Make sure heat from lights is not triggering sensor Sensor must be located below and as far away as possible from its lights STL360Q1 STL360Q2 amp STL360Q3 Kits Mount only on non combustible surfaces Side View 6 10 wrong wrong OK TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 20 40 6 10 60 Reduced Range Maximum Range mask 4 3 60 60 20 mauvais mauvais BON Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire cover
116. ovement far away and directly towards sensor is not entirely within one zone Problem Sensor will not detect until movement crosses zones Solution Micro Adjust sensor by moving sideways 1 4 This may move the zones to allow earlier detection Technical Tips Range Appears Limited 20 40 Reduced Range 6 10 60 Maximum Range No detection until here Detection here now Less Sensitive More Sensitive 20 19 MAUVAIS BON Conseils techniques La port e semble limit e Technical Tips Lights Turn Off Too Quickly 1 Check if sensor is being tricked by reflected light If lights controlled by the sensor shine or reflect into the photocell locat ed behind the lens the unit will go on briefly see its own light and turn off thinking that it is daytime Problems Lights reflect into photocell Lights shine directly into photocell Solution Adjust SUN MOON knob slightly clockwise to allow operation at higher ambient light levels Alternatively move the lights or reflectors or mask the lens in the direction of the lights and or reflections 2 Check if R lamps non reflector A lamps or self ballasted PL lamps are being used in a non enclosed lampholder If so switch to reflector PAR floodlight lamps or Quartz floods so the sensor is not affected by stray light If using PAR floodlights con sider using lower wattage energy saving lamps TIME 12 MINS
117. r une plus grande zone Voir les pages 11 12 pour r gler les param tres du d tecteur On peut aussi utiliser le masque de lentille pour r duire consid rablement la protection ou permettre le mouvement non d tect de certaines directions 5 Le STL360 est r gl l usine pour le fonctionnement de nuit seulement Pour le fonctionnement 24 heures tourner la commande de photocellule compl tement en direction du symbole SOLEIL LUNE Tourner gauche pour que le d tecteur fonctionne plus tard au cr puscule et droite pour qu il fonctionne plus t t 6 R p ter les tapes 1 5 jusqu ce qu on soit satisfait de la protection Le d tecteur est maintenant pr t fonctionner Walk Testing STL360 s full coverage pattern reduces the need for aiming and adjustment The purpose of the Walk Test is to check and adjust the coverage pattern The STL360 has a Test Period which allows the sensor to be walk tested day or night To enter Test Mode The sensor is in Test Mode when power is first applied Turn power off for at least 10 seconds and back on 1 Aim the sensor at the traffic pattern you want to detect Sensor will detect any movement ACROSS its pattern most effectively 2 Start outside the pattern and walk across the pattern until the lights go on As distance from the sensor increases it will take more movement to be detected 3 Adjust sensor aiming as necessary to improve coverage Make sure
118. rom passing cars 8 Make sure heat from lights is not triggering sensor Make sure the sensor is below and as far as possible away from sensor 16 20 safety zone OK 15 1 Make sure the sensor is installed on its own dedicated circuit free of motor loads such as HVAC equipment kitchen appliances or garage door openers 2 It is not recommended to wire sensors in parallel More than one sensor wired together makes them difficult to troubleshoot Disconnect multi ple sensors and test separately 3 Keep all people completely out of the detection pattern to make sure the sensor is not detecting them 4 Make sure sensor is located below and as far as possible from its lights Heat from the lights may trigger the sensor Solution Move sensor below and away from the lights 5 Make sure lights are not reflecting back into sensor Check for white or reflective surfaces close to the sensor Solution Aim sensor away from reflective objects or move the objects and lower sensitivity 6 Make sure sensor is not aimed within 20 feet of a road or sidewalk Passing cars will activate sensor Solution A 20 foot safety zone and reduced sensitivity are recommended to avoid activation from passing cars 7 Heavy rain snow or high winds may activate the sensor occasionally Reduce sensitivity control slightly until problem stops 8 Moths can be attracted to the lights and fly close to the sensor causing triggering Re
119. rre de la bo te de jonction 7 Positionner les joints de la plaque EZ et la plaque de m tal voir la page 7 8 D nuder 1 2 po d isolation de tous les conducteurs Brancher comme illustr dans le sch ma de raccordement 9 Visser les connecteurs de fils Fixer en place avec du ruban d lectricien 10 S assurer que toutes les ouvertures inutilis es de la plaque EZ sont bouch es bouchons fournis 11 Visser les ampoules en place Mettre sous tension 12 Effectuer un test de marche pour r gler la r ponse du d tecteur voir page 15 STL360 Assembly and Wiring To install a STL360 Sensor with separately purchased floodlights start at 1 To install STL360 Pre wired Floodlight Kits see page 7 1 Screw the threaded arms of each floodlight into the RAB CU4 EZ Plate See diagram on page 7 2 Screw the threaded arm of the sensor into the bottom hole of the EZ Plate Sensor should be below and as far away from the floodlights as possible 3 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 4 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during wiring 5 Bring power leads light fixture and sensor leads through holes in all gaskets and mounting plates into junction box 6 Attach
120. s Mask Crossbar with Green Ground Screw Hanging Hook 1 2 Close Up Plugs 3 Slotted Screws 4 Finishing Cap O ring Gasket Center Mounting Screw Foam Gaskets 2 Metal Plate MAKES IT EASY Easy Installation amp Product Help Toll Free Phone Toll Free Fax Fax on Demand Call our friendly experts Send faxes to RAB Faxed information 8AM 6PM ET Mon Fri 24 7 24 7 888 RAB 1000 888 RAB 1232 888 RAB 1236 E mail www rabweb com Questions and requests Visit our internet site answered promptly for product information tech rabweb com RAB Lighting 170 Ludlow Avenue Northvale New Jersey 07647 U S A RAB Lighting 2004 Incorrect Correct 22 21 2 masques de lentille tiquette de plaque d interrupteur int rieure 3 connecteurs Outil d ajustement Masque de lentille en mylar Barre transversale vis de mise la terre verte Crochet de fixation Bouchons de 1 2 po 3 Vis filets interrompus 4 Capuchon de finition Joints toriques 2 Vis de montage centrale Joints de mousse 2 Plaque de m tal
121. s within ten years from the date of original purchase For repair replacement return the product freight prepaid and insured to RAB Lighting 170 Ludlow Avenue Northvale NJ 07647 The STL360 should be packed carefully Please include your sales receipt and a description of the problem If your unit is out of warranty or the damage is unrelated to the original manufacture return your unit directly to us with a check for 20 00 made out to RAB Electric We will repair or replace your unit Under no circumstances shall we be liable for any incidental or consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property or revenue or cost of installation removal or re installation This warranty gives you specific legal rights and you may also have other rights which vary from state to state Contents of Accessory Kit 2 Lens Masks Indoor Switchplate Label 3 Wire Nuts Adjustment Tool Mylar Lens Mask Crossbar with Green Ground Screw Hanging Hook 1 2 Close Up Plugs 3 Slotted Screws 4 Finishing Cap O ring Gasket Center Mounting Screw Foam Gaskets 2 Metal Plate MAKES IT EASY Easy Installation amp Product Help Toll Free Phone Toll Free Fax Fax on Demand Call our friendly experts Send faxes to RAB Faxed information 8AM 6PM ET Mon Fri 24 7 24 7 888 RAB 10
122. sensitivity may help 9 Check Solutions 3 4 5 6 7 and 8 under If Lights Do Not Turn Off Technical Tips Lights Turn On and Off Inappropriately 1 Check that lamps and fixtures work Compare wiring to the wiring diagram in this manual Check that the power is on 2 If installing during daylight remember that the sensor will provide 2 minutes of Test Time after power is turned on After 2 minutes the sensor will switch to Automatic Mode and will not work during day light if the photocell control is turned to the night only position moon symbol If you require 2 more minutes of Test Time turn the power off for at least 10 seconds and back on again If you require the sensor to operate both day and night turn the SUN MOON control knob clockwise to the sun and moon symbol 3 Check that lights from another source such as adjacent porch lights garden lights or street lights are not in the sensor s view The sen sor s photocell may detect the light and deactivate daylight If you desire the sensor to operate in higher ambient light levels turn the SUN MOON control knob counter clockwise toward the sun symbol 4 Was sensor wired hot If so circuitry may have been damaged Technical Tips Lights Do Not Turn On 20 safety zone TIME 12 MINS SENS TIME 12 MINS SENS 18 17 WRONG OK MINUTERIE SENSIBILIT Technical Tips Lights Turn Off Too Quickly 1 Check
123. sensor 4 Check that movement far away and directly towards sensor is not entirely within one zone Problem Sensor will not detect until movement crosses zones Solution Micro Adjust sensor by moving sideways 1 4 This may move the zones to allow earlier detection Technical Tips Range Appears Limited 20 40 Reduced Range 6 10 60 Maximum Range No detection until here Detection here now Less Sensitive More Sensitive 20 19 Conseils techniques Les luminaires s teignent trop rapidement 1 V rifier si le d tecteur est d clench intempestivement par la lumi re r fl chie Si les luminaires command s par le d tecteur clairent ou r fl chissent dans la photocellule derri re la lentille l unit est d clench e bri vement capte sa propre lumi re et s teint en pensant qu il fait jour Probl mes La lumi re r fl chit dans la photocellule La lumi re brille directement dans la photocellule Solution R gler le bouton SOLEIL LUNE l g rement droite pour permettre le fonc tionnement aux niveaux d clairage ambiant plus lev s Par ailleurs d placer les lampes ou r flecteurs ou masquer la lentille en direction de la lumi re et ou de la r flexion 2 V rifier si des lampes R des lampes A autres qu r flecteur ou des lampes PL ballast sont utilis es dans un porte lampe non encastr Le cas ch ant
124. sing a Location The best location is where the sensor can see all paths of movement The sensor may be wall or soffit mounted As distance from the sensor increases larger movement will be required for detection For instance at 10 feet a half step will be enough while at 50 feet several steps will be necessary for detection How large an area does STL360 protect Two powerful detectors combine to give the STL360 180 x 60 long forward range plus superb 360 downward detection below and to all sides Mounting Height Mounting at 6 12 above the ground allows maximum range If the sensor is mounted above 15 high the usable range is reduced Location Tips Difficult Locations Sensor may be triggered by unwanted movement or heat source such as a swaying tree road traffic dryer vent swimming pool or hot tub To Improve Performance in Difficult Locations Reduce sensitivity by turning the SENS knob counterclockwise and or Mask lens in the direction of the unwanted movement or heat source using the lens mask provided or opaque tape Mounting Stability Mount sensor on stable surface Do not mount on a tree or pole that will move in the wind Make sure sensor and lights are mounted firmly If they move when touched tighten all screws Light vs Sensor Position Make sure heat from lights is not triggering sensor Sensor must be located below and as far away as possible fro
125. sted PL lamps are being used in a non enclosed lampholder If so switch to reflector PAR floodlight lamps or Quartz floods so the sensor is not affected by stray light If using PAR floodlights con sider using lower wattage energy saving lamps TIME 12 MINS SENS OK WRONG 1 Check that the sensor is level from side to side and pointed at the area you desire If unit is tilted part of the detection zone may be high in the air over people s heads Solution Position sensor exactly level from side to side 2 Check that the sensor is not mount ed too high If mounted above 20 feet much of the usable range will be lost Solution Mounting at 6 feet to 10 feet allows maximum range 3 Check that movement is not directly towards sensor Sensor will see movement across its pattern more quickly To fix move the sensor 4 Check that movement far away and directly towards sensor is not entirely within one zone Problem Sensor will not detect until movement crosses zones Solution Micro Adjust sensor by moving sideways 1 4 This may move the zones to allow earlier detection Technical Tips Range Appears Limited 20 40 Reduced Range 6 10 60 Maximum Range No detection until here Detection here now Less Sensitive More Sensitive 20 19 20 pi 6 10 pi 60 pi Port e r duite Port e maximale Moins sensible Plus sensible 40 pi Aucune d tect
126. switch that operates the sensor twice off on off on within 2 seconds you will override the sensor to keep lights on continuously until dawn If you set the Manual Override Mode during daylight the sensor will be prepared to turn on at dusk and remain on until dawn This is a handy feature if you leave home for the day and you want the lights on to greet you when you return When the sensor is in Ready for Manual Override Mode the middle LED will be on TO RESUME AUTOMATIC MODE Switch OFF the power for at least 10 seconds then turn it ON again Sensor will reset to Automatic Mode after completing the warm up period and Test Mode 14 On Guard Auto Mode LEDs scan continuously back and forth Ready for Manual Override Mode Middle LED on Ready for Evening Timer Mode Middle LED blinks 13 DAYTIME 24 HOUR OPERATION OF MANUAL OVERRIDE If you set Manual Override while set to 24 hour operation lights will come on and remain on continuosly Lights will not turn off at dawn MODE MINUTERIE SOIR E Garde l clairage en fonction pendant 1 8 heures apr s le cr puscule Le d tecteur retourne alors en mode automatique jusqu l aube Si le mode minuterie de soir e est programm le jour le d tecteur est pr t allumer les luminaires au cr puscule et celles ci restent allum es pendant le nombre d heures pro gramm Si le d tecteur est en Pr t pour le mode minuterie de soir e la
127. t is to check and adjust the coverage pattern The STL360 has a Test Period which allows the sensor to be walk tested day or night To enter Test Mode The sensor is in Test Mode when power is first applied Turn power off for at least 10 seconds and back on 1 Aim the sensor at the traffic pattern you want to detect Sensor will detect any movement ACROSS its pattern most effectively 2 Start outside the pattern and walk across the pattern until the lights go on As distance from the sensor increases it will take more movement to be detected 3 Adjust sensor aiming as necessary to improve coverage Make sure sensor is level 4 Sensitivity may be decreased with the SENS knob to detect a limited area or if the sensor is being activated by wind foliage traffic or animals or increased to cover a larger area See p 11 12 to adjust sensor settings The lens mask can also be used to drastically reduce coverage or allow undetected movement from some directions 5 STL360 is factory set for night only operation For 24 hour operation turn the photocell control completely toward the SUN MOON setting Turn counter clockwise to have the sensor come on later at dusk clockwise to have it come on earlier 6 Repeat steps 1 5 until you are satisfied with coverage Your sensor is now ready for operation Technical Tips Lights Do Not Turn Off 1 Make sure that the sensor is not in Manual Override Mode Turn power OFF for 10 sec
128. t programm e pendant le fonctionnement 24 heures la minuterie de soir e se mettra imm diatement en marche apr s l actionnement de l interrupteur Adjusting the Settings TIME Sets the time that lights will remain on after the detection zone is vacated Adjustable from approximately 5 seconds to 12 minutes The Factory Setting is 12 minutes PHOTOCELL For night only operation turn the knob completely counterclockwise to to the MOON symbol For 24 hour operation turn the knob all the way clockwise to the MOON SUN symbol Adjust counterclockwise to have the sensor come on later at dusk clockwise to have it come on earlier The Factory Setting is Night only MOON If you set Evening Timer while set to 24 hour operation Evening Timer will begin immediately after flipping switch SENSITIVITY Increases or decreases the responsiveness and range of the sensor adjustable from 30 to 100 The Factory Setting is 100 Adjusting the Settings EVENING TIMER The STL360 provides an alternative to normal motion activated lighting The EVENING TIMER can keep lights on continuously without motion for 1 to 8 hours after dusk This is great for evening activities requiring continuous light During vacations the EVENING TIMER provides a lived in look by simulating an occupant turning lights on at dusk and then off at bedtime To set the EVENING TIMER flip the wall switch controlling the sensor three times slowly off o
129. tch to Automatic Mode and will not work during day light if the photocell control is turned to the night only position moon symbol If you require 2 more minutes of Test Time turn the power off for at least 10 seconds and back on again If you require the sensor to operate both day and night turn the SUN MOON control knob clockwise to the sun and moon symbol 3 Check that lights from another source such as adjacent porch lights garden lights or street lights are not in the sensor s view The sen sor s photocell may detect the light and deactivate daylight If you desire the sensor to operate in higher ambient light levels turn the SUN MOON control knob counter clockwise toward the sun symbol 4 Was sensor wired hot If so circuitry may have been damaged Technical Tips Lights Do Not Turn On 20 safety zone TIME 12 MINS SENS TIME 12 MINS SENS 18 17 WRONG OK BON MAUVAIS 1 Make sure the sensor is installed on its own dedicated circuit free of motor loads such as HVAC equipment kitchen appliances or garage door openers 2 It is not recommended to wire sensors in parallel More than one sensor wired together makes them difficult to troubleshoot Disconnect multi ple sensors and test separately 3 Keep all people completely out of the detection pattern to make sure the sensor is not detecting them 4 Make sure sensor is located below and as far as possible from
130. teurs de la trousse de d tecteur par les trous de tous les joints dans la bo te de jonction 4 D nuder 1 2 po d isolation de tous les fils 5 Fixer le ou les fils de terre la vis de mise la terre de la bo te de jonction Raccorder comme illustr dans le sch ma de raccor dement la page 7 6 Visser les connecteurs de fils Fixer en place avec du ruban d lectricien 7 Aligner les joints la plaque EZ et la plaque de fixation de m tal pour bien sceller Serrer la vis centrale de la plaque EZ s assurer que le joint torique se trouve sur la vis pour fixer la plaque EZ la bo te 8 Ins rer le capuchon de finition de plastique au centre de la plaque CU4 EZ pour prot ger contre les intem p ries 9 Appliquer un calfeutrant de silicone autour de toutes les ouvertures pour bien sceller contre les intem p ries 10 Visser les ampoules en place Mettre sous tension Effectuer un test de marche pour r gler la r ponse du d tecteur page 15 Assemblage et raccordement de la trousse STL360 STL360 Kit Assembly and Wiring STL360 floodlight kits come pre wired and assembled on the RAB CU4 EZ plate allowing for mounting on round rectangular or octagonal surface or recessed boxes Mounting Wiring STL360 Kit Assembly and Wiring 1 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof
131. tions best when the direction of expected movement is across its detection pattern not towards the sensor Mount 6 12 high for optimum range and detection The STEALTH360 is the most reliable and technically advanced motion activated light control ever produced This techni cal manual is written for electrical professionals who wish to maximize the performance and reliability of this superb sensor RAB welcomes your questions or comments Please call 888 722 1000 or email tech rabweb com Thank you for purchasing a RAB sensor STL360H STL360HBW STL360Q1 STL360Q3W STL360Q2W Installation Manual Specifications Switching Capacity 8 amps 1000 watts Incandescent and 250 watts Fluorescent Voltage 120 volts Protection Pattern 180 forward 360 below and to all sides Time Adjustment 5 seconds to 12 minutes Power Consumption 1 watt Surge protection 6000 volts Cautions TURN OFF ALL POWER AT CIRCUIT BREAKER FUSE PANEL Read entire Installation Manual before proceeding All wiring should comply with local electrical codes and requires a qualified electrician The total lighting load connected to STL360 must not exceed 1000 watts incandescent or quartz 250 watts fluorescent To switch more wattage an electrician can install a relay Line Carrier Remote Control Systems such as X 10 Leviton or Radio Shack are incompatible with sensors and may cause false activations Do not install sens
132. triggered by unwanted movement or heat source Solution 1 Aim sensor away from movement or 2 Mask lens as in the direction of the source 3 Lower sensitivity control setting 4 Make sure sensor and lights are mounted firmly and do not move even slightly when touched If they move tighten all screws 5 Make sure sensor is not mounted on an unstable object such as a tree or pole that will move in the wind Problem Movement of tree triggers sensor Solution Mount on stable surface 6 Was sensor wired hot If so circuitry may have been damaged 7 Make sure sensor is not aimed within 20 feet of a road Problem Passing cars activate sensor Solution A 20 foot safety zone and lower sensitivity are recommended to avoid activation from passing cars 8 Make sure heat from lights is not triggering sensor Make sure the sensor is below and as far as possible away from sensor 16 20 safety zone OK 15 BON Zone de s curit de 20 pi 1 S assurer que le d tecteur est install sur son propre circuit d di sans charges moteur comme de l quipement de climatisation des ap pareils de cuisine ou un ouvre porte de garage 2 On recommande de raccorder les d tecteurs en parall le Les d tecteurs raccord s en s rie compliquent le d pannage D connecter les d tecteurs multiples et les tester s par ment 3 loigner toutes les personnes de la zone de d tection pour s assurer qu
133. tts incandescent or quartz 250 watts fluorescent To switch more wattage an electrician can install a relay Line Carrier Remote Control Systems such as X 10 Leviton or Radio Shack are incompatible with sensors and may cause false activations Do not install sensors on a circuit that feeds motor loads such as kitchen appliances HVAC equipment washer dryer or garage door openers Sensor functions best when the direction of expected movement is across its detection pattern not towards the sensor Mount 6 12 high for optimum range and detection The STEALTH360 is the most reliable and technically advanced motion activated light control ever produced This techni cal manual is written for electrical professionals who wish to maximize the performance and reliability of this superb sensor RAB welcomes your questions or comments Please call 888 722 1000 or email tech rabweb com Thank you for purchasing a RAB sensor STL360H STL360HBW STL360Q1 STL360Q3W STL360Q2W Installation Manual Caract ristiques Capacit de commutation 8 A Incandescence de 1000 watts ou fluorescence de 250 watts Tension 120 volts Configuration de protection 180 avant 360 derri re et tous les c t s R glage de la minuterie 5 secondes 12 minutes Consommation 1 watt Protection contre les surtensions 6000 volts Specifications Switching Capacity 8 amps 1000 watts Incandescent and 250 w
134. ure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor will see movement ACROSS its pattern more quickly Check that movement far away and directly towards sensor is not entirely within one zone To fix change the sensor location If the sensor is located over a pathway so all movement is directly toward it range may appear limited Micro Adjust sensor by moving sideways 1 4 or so which may reposition the zones enough to allow earlier detection Choose a Protected Location Mount sensor in protected area The more protected the mounting location the less chance of lights turning on occasionally during rain snow and windstorms because the sensor is detecting dramatic changes in temperature 20 safety zone TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS Lens Mask included OK OK WRONG Less Sensitive More Sensitive Better detection after micro adjustment OK WRONG 6
135. ve a more accurate location of movement and trouble free operation Multiple Fixtures Multiple fixtures may be wired to a single sensor To handle loads greater than 1 000 watts a qualified electrician should install a relay Power Quality It is not recommended to install sensors on a circuit that also feeds motor loads such as HVAC equipment kitchen appliances or garage door openers The Stealth circuit is surge and transient protected to IEC specifications However if voltage varies significantly from 120 volts which may occur on circuits with motor loads the sensor may malfunction 10 Power In White Red Black Power In White Sensor Red Black 9 Black STL360 Assembly and Wiring To install a STL360 Sensor with separately purchased floodlights start at 1 To install STL360 Pre wired Floodlight Kits see page 7 1 Screw the threaded arms of each floodlight into the RAB CU4 EZ Plate See diagram on page 7 2 Screw the threaded arm of the sensor into the bottom hole of the EZ Plate Sensor should be below and as far away from the floodlights as possible 3 Attach the Universal Mounting bar with the bar screws provided to the junction box If you are attaching your STL360 kit to a surface mount weatherproof box you must use both gaskets with the metal mounting plate sandwiched between 4 Easy Wiring Tip Use the S shaped Hands Free Hanging Hook to hold the EZ Plate during
136. ve when touched tighten all screws Light vs Sensor Position Make sure heat from lights is not triggering sensor Sensor must be located below and as far away as possible from its lights STL360Q1 STL360Q2 amp STL360Q3 Kits Mount only on non combustible surfaces Side View 6 10 wrong wrong OK TIME 1 8 HRS 5 SECS 12 MINS EVENING TIMER SENS 20 40 6 10 60 Reduced Range Maximum Range mask 4 3 60 60 20 Choosing a Location Locations Near Roads Cars and passing traffic may activate the sensor if it is aimed at the road To Improve Performance in Locations Near Roads Reduce sensitivity by turning the SENS knob counterclockwise Mask the lens in the direction of the traffic using the lens mask provided or opaque tape Lens mask can be broken along lines to desired size Make sure that sensor is not aimed at traffic The sensor should be aimed down so that the maximum range of the sensor ends at least 20 from the road This will avoid detection of passing trucks and cars or the air currents they create Mount Level The sensor should be mounted level from side to side and pointed at the area where you desire coverage If tilted part of the detection zone may be high in the air over people s heads Choosing a Location Locate for Movement Across Pattern Check that movement is not directly towards sensor Sensor
137. wired to a single sensor To handle loads greater than 1 000 watts a qualified electrician should install a relay Power Quality It is not recommended to install sensors on a circuit that also feeds motor loads such as HVAC equipment kitchen appliances or garage door openers The Stealth circuit is surge and transient protected to IEC specifications However if voltage varies significantly from 120 volts which may occur on circuits with motor loads the sensor may malfunction 10 Power In White Red Black Power In White Sensor Red Black 9 Black Adjusting the Settings TIME Sets the time that lights will remain on after the detection zone is vacated Adjustable from approximately 5 seconds to 12 minutes The Factory Setting is 12 minutes PHOTOCELL For night only operation turn the knob completely counterclockwise to to the MOON symbol For 24 hour operation turn the knob all the way clockwise to the MOON SUN symbol Adjust counterclockwise to have the sensor come on later at dusk clockwise to have it come on earlier The Factory Setting is Night only MOON If you set Evening Timer while set to 24 hour operation Evening Timer will begin immediately after flipping switch SENSITIVITY Increases or decreases the responsiveness and range of the sensor adjustable from 30 to 100 The Factory Setting is 100 Adjusting the Settings EVENING TIMER The STL360 provides an alternative to nor
138. y wind foliage traffic or animals or increased to cover a larger area See p 11 12 to adjust sensor settings The lens mask can also be used to drastically reduce coverage or allow undetected movement from some directions 5 STL360 is factory set for night only operation For 24 hour operation turn the photocell control completely toward the SUN MOON setting Turn counter clockwise to have the sensor come on later at dusk clockwise to have it come on earlier 6 Repeat steps 1 5 until you are satisfied with coverage Your sensor is now ready for operation Technical Tips Lights Do Not Turn Off 1 Make sure that the sensor is not in Manual Override Mode Turn power OFF for 10 seconds then ON Sensor will be in Test Mode for approximately 2 minutes then it will switch to Auto Mode with lights off and ready to detect movement 2 Make sure that the sensor is not in Evening Timer Mode Turn power OFF for 10 seconds see 1 3 Make sure sensor is not aimed at or mounted over something that would move or change temperature such as waving branches water air condi tioners windows or heating vents even on neighboring property You can test for infrared sources in the area by placing a box or bag over the sensor Put sensor into test mode Lights should stay off Wave your hand inside bag in front of sensor Lights should go on and then time out If sensor operates properly when covered check items 4 8 Problem Sensor is

Installation Manual

Contents

Download Pdf Manuals

Related Search

Related Contents