installation manual
Contents
1. MO i 5 4 rt a M py mal AA Il AG JHII I deN L A NT ke i 7 7 HA J U r 1675 std Generator box 4 Planmeca intra X ray unit Installation manual INSTALLATION POSSIBILITIES Wall mounting with remote control in treatment room see section 7 REMOTE CONTROL PANEL INSTALLATION on page 48 Telephone cable max 12m Generator box ii r 1525 Control panel Qj o extension a arm 835mm ee ae Dental unit r 1975 A FElgfo _ N extension 4 arm 760mm oi KS fT FS ae a S extension S N l arm 535mm s S r 1675 std A S extension S arm 385mm J O Se m Installation manual Planmeca Intra X ray unit 5 INSTALLATION POSSIBILITIES Ceiling mounting in treatment room see section 5 1 Ceiling installation on page 25 NOTE The extension arm 535mm 21 1 in is recommended for the ceiling instal lation Also the short extension arm can be used but the long extension arm is not recommended NOTE Both the Delight S and Delight operating light for unit mounting can be installed to the ceiling arm using an additional arm IR3 eps Generator Extension cable max 12 m Control panel Dental unit 6 Planmeca intra X ray u2. 1 INTRODUCTION This manual contains all the information required to install and set up the Planmeca Intra X ray unit Please read this manual carefully before installing the X ray unit WARNING Failure to install the Planmeca Intra X ray unit in an approved location may be dangerous to both patient and operator AN CAUTION It is very important that the room in which the Planmeca Intra X ray unit is installed and the position from which the equipment is operated are correctly shielded against radiation Since radiation safety requirements vary from country to country and state to state it is the responsibility of the installer to ensure that all local and national safety regulations are met NOTE In case the Planmeca Dixi digital intra X ray system is going to be installed to the Planmeca Intra X ray unit use the Dixi digital intra X ray system installation manual in conjunction with this manual The manufacturer assembler and importer are responsible for the safe ty reliability and performance of the X ray only if installation calibration modification and repairs are carried out by qual ified and authorized personnel electrical installations are carried out according to the appropriate re quirements such as IEC364 equipment is used according to the operating instructions Planmeca pursues a policy of continual product development Although every effort is made to produce up to date produ
3. Intra_box5 e Telephone cable Bottom plate ps Intra_box10 e Alternative 3 ps Intra_box11 e NOTE You can connect the telephone cable to the Extension cable PCB before attaching the bottom plate to the wall socket Refer to section 8 3 Con necting the cables on page 53 52 Planmeca Intra X ray unit Installation manual FIXED CONTROL PANEL INSTALLATION 8 3 Connecting the cables Connect the telephone cable between the Generator PCB and Extension cable PCB according to the figure below Telephone cable concealed wiring phone cable ace mounting option ps Intra_box12 e Telephone cable Extension cable PCB Installation manual Planmeca Intra X ray unit 53 FIXED CONTROL PANEL INSTALLATION In case the double exposure button is installed connect the cables according to the figure below ps Telephone cable Double exposure button cable Intra_box13 e Double exposure button Extension cable PCB AVI O Generator PCB ooo o oo oo P ooooo Pepo
4. WARNING Do not touch the painted screws or the earth spring attachment screw 2 5 Allen screw 60 Planmeca Intra X ray unit Installation manual RUNNING IN THE X RAY UNIT 12 RUNNING IN THE X RAY UNIT After installation before using the unit for the patient work the following exposures must be taken to run in the unit Switch the unit on The on off switch is located under the generator box Take three exposures with exposure values 60 kV and 0 05 seconds Take three exposures with exposure values 70 kV and 0 1 seconds Take three exposures with exposure values 70 kV and 1 0 seconds Installation manual Planmeca Intra X ray unit 61 EN PLANMECA OY Asentajankatu 6 00880 Helsinki Finland tel 358 20 7795 500 AYNASH fax 358 20 7795 555 e mail sales planmeca com www planmeca com
5. PLANMECA installation manual TABLE OF CONTENTS INTRODUCTIONE aE E E ccc cats dich saeccevascuadessaceruvstetevasvaccssssiecshobsdsace ches sucentantuctvsges T TE 1 2 PRE INSTALLATION REQUIREMENTS i cccc ccinccicesscccesseceecessadencecteceasccexceacestedencedsnccesevcoorecsuscdeeveccedsndbienenss 2 2 1 Environmental requirements 0 0 0 ec cececeeeeeeeeeeeeneeeeeeeeeeeeeeeeeaeeeeeeeaeeeeeseaaeeeeesesaeeeeeeseaeeeeeeeeaeeeees 2 Wall CONSUUCHOM wccctscecite hata T A E E nh annette ein E 2 Temperature amp Murmiciity resser ANA NE E EE AE 2 22 Electricalirequirements riirii e a a a a een ive h a es 2 Mams voltage sirare E R a a ea a 2 Mams frequency sst cce ckeetecectzeen cclatecehelerehideetd nedecedeno A e aa aa aa a a a es 2 Internal Mains fuse ratings ini cated cpr eign a asda Meee dana R EAO 3 External mains fuse recommendation ceeceeeeceeeeeeeeeneeeeeeeeeeeeeeeeeaeeeeeeeeaaeeeeeeeeaaeeeeeeeeaeeeeeeeaas 3 GYOUNGING ssc tetes ste a a a Reach ira rea hte deat Ratatat 3 Power CONSUMPTION osiin tenes vies tee eects eee eee tee E aaa a AS POA reve ieee AE K EAE eevee 3 3 INSTALLATION POSSIBILITIES 2 002 s ceccvee coc iedie cats destuand castecnessstecstetedecusds a a ar a a aa eaa aeh eiei iaa ninen nani 4 3 1 Mounting alternatives egeo a a rE D EOL 4 Standard wall mounting in treatment room see section 4 STANDARD INSTALLATION TO AWALE on page TI a a aaa eaa ae tua dea ianh ada aer PTEE A graa beset 4 Wall mounting w
6. in depth hole and place the expansion anchor into it Attach the adapter plate to the ceiling with one of the fastening screws Remove the adjustment nuts from the three mounting holes Attach the drilling tool to one of the holes and drill the second hole using the drilling tool as a guide Drill the two other holes in the same way Remove the adapter plate and insert the expansion anchors into the holes Attach the plate to the ceiling with four M8x35 DIN 912 screws and 8 4 17 DIN 125 washers Use the adjustment nuts and the adjustment plates with the screws at each corner of the adapter plate W Sa et ee v Vo E lt Adapter plate Installation manual Planmeca Intra X ray unit 25 OTHER INSTALLATION ALTERNATIVES Wooden ceiling Attach the adapter plate to the ceiling with four 8x80 DIN 571 lag screws Do not use the expan sion anchors with wooden ceiling Use the adjustment nuts and the adjustment plates with the screws at each corner of the adapter plate NOTE If the concealed wiring is not used the extension cable must be lead so that there is at least 1 2 m cable after adapter plate min 1 2 m 26 Planmeca Intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES Shorten the ceiling arm if needed and attach the mounting rings to the arm Do not tighten the screws yet mounting ring must be on the lower edge of the ring Mounting rings T and the scre
7. l l ELMP Pink l Ferrite l Installation manual Planmeca Intra X ray unit 33 OTHER INSTALLATION ALTERNATIVES Fasten the cover to the opening of the ceiling arm Pc a Q 2 lt x ey a pel 8 Oo 1 Loosen the locking screw and either leave it loose so that the arm can be rotated 700 or tighten it to the position desired by the customer Attach the cover plugs 34 Planmeca Intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES Delight operating light installation The operating light can be installed to the ceiling arm of the Planmeca Intra X ray unit Delight operating light without power contol Make sure that the operating light cable is installed Attach the arm and the Delight operating light according to the figure below Make sure that the light cable is in the groove of the light arm pivot when attaching the light to the horizontal arm M4x6 DIN 912 3 5x13 DIN 7981 ight_ceiling_inst_07 eps Intra_deli BLUE BULB BLACK BULB AND s SWITCH COMMON YELLOW 5 SWITCH M6x17 DIN 7991 polo JSYELLOW J NOTE The ABSOLUTE MAXIMUM allowed bulb voltage is 18 5 Vrms measured at the bulb socket YELLOW Installation manual Planmeca Intra X ray unit 35 OTHER INSTALLATION ALTERNATIVES Delight operating light with power contol Atta
8. 90V 110V 110 115V 99V 126V 220 240V 198V 264V NOTE Please note that the ratings of the internal as well as external mains fuses are depending on the mains voltage setting AN CAUTION Never connect the X ray unit to the mains without first checking the voltage setting Incorrect voltage setting can cause damage to the X ray electronics Mains frequency The mains frequency is 50 or 60 Hz and is independent on the mains voltage setting 2 Planmeca intra X ray unit Installation manual PRE INSTALLATION REQUIREMENTS Internal mains fuse ratings The Planmeca Intra X ray unit is equipped with dual mains fuses live and neutral However in some areas it is not allowed to have a fuse in the neutral wire The neutral fuse is optionally bypassed at the factory in which case the X ray unit is equipped with one mains fuse The ratings for the internal mains fuses are units with 100V or 110 115V voltage setting 15AT 250V slow blow 6 3x32mm special fuse manufacturer Bussmann type MDA units with 220 240V voltage setting 8AT 250V slow blow 6 3x32mm special fuse manufacturer Bussmann type MDA External mains fuse recommendation The recommendation for the external mains fuses are units with 100V or 115V voltage setting 16A time lag units with 220 240V voltage setting 10A time lag No other equipment should be connected to the same fused mains line as the X ray un
9. WITHOUT THE ADAPTER PLATE When the concealed wiring is used the cable coming from the ON OFF switch to the connector P7 must be moved to the connecto P10 Also the fuse F3 must be removed MAINS N INPUT Neutral Line Blue Brown ROM MAINS Blue SWITCH F4 Brown Remove Fuse F3 Ins1 Attach the extension cable to the generator box assembly as shown on the figure below Place the generator housing over the generator assembly Generator housing Extension cable 46 Planmeca Intra X ray unit Installation manual ATTACHING THE GENERATOR BOX WITHOUT THE ADAPTER PLATE Secure the cover into position with the three M4x6 ULS screws ps M4x6 ULS _15APSU2 e Connect the control panel cable to its terminal at the underside of the generator box Installation manual Planmeca Intra X ray unit 47 REMOTE CONTROL PANEL INSTALLATION 7 REMOTE CONTROL PANEL INSTALLATION WARNING Ensure that the power supply is switched off before connecting the cables NOTE Use the telephone cable max 12 m between the generator box and the data wall socket Attach the frame of the data wall socket to the wall with two 4x30 DIN 7981 screws If the wall is made of concrete or brick drill 96 mm 0 23 in 32 35 mm 1 25 in in depth holes and place the expansion anchors into them If the wall is made of wood or plaster attach the fra
10. 1 Attaching the standard adapter plate to wall The Planmeca Intra X ray unit must be positioned in accordance with the information given in the installation pattern supplied with the unit The X ray unit should be positioned within the reach of the power supply cable 8m 118 in In the case that concealed wiring is used the cable outlet should be positioned next to on the right hand side the adapter plate The wall plate is attached to the wall according to the instructions given in next pages If the wall is made of concrete or brick use the M8x30 DIN 912 screws and the expansion anchors If the wall is made of wood or plaster use the 8x80 DIN 571 lag screws Do not use the expansion anchors with wooden or plaster wall See figure below The minimum widths stated are measured using the 535 mm 21 1 in long extension arm IR7 eps For 385 mm 15 2 in TE extension arm subtract 150 A mm 5 9 in from the mini mum width LLL rs For 760 mm 30 0 in r extension arm add 225 mm 8 9 in to the minimum width Width min 1000mm Width min 1100mm min 39 in min 43 in For 835 mm 32 9 in f extension arm add 300 mm x BIBIgnt PLAAN A k 12 in to the minimum N width YNNNNNNN Wall made of Wooden or plaster wall concrete or stone Q M8x30 DIN 912 GETAN 10 mm 0 4 in 32 35 mm 1 25 in 8x80 DIN 571 5mm 0 2 in 55 60 mm 2 2 in Install
11. 2 mm on a a 2 65 80 mm Move the lower mounting ring to the position shown on the figure below Tighten all the mounting rings screws firmly 30 32 mm 100 105 mm Ceil4 eps Installation manual Planmeca Intra X ray unit 29 OTHER INSTALLATION ALTERNATIVES With a spirit level make sure that the ceiling arm is vertical Adjust its position with the adjustment nuts if needed Adjustment nut Attach the cover label over the dent Ceil5 eps Remove the extension arm shaft Remove the shaft nut by hitting it as shown on the figure below Remove the support plate and the shaft The shaft is not needed in this installation 30 Planmeca Intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES Assemble the bracket arm to the extension arm refer to the section 4 2 Assembling the arm on page 15 Assemble the bearing housing to the extension arm as described in figure below Support plate Attach the shaft nut Ceiladap5 eps Install the X ray unit to the ceiling arm and lock it immediately to its position with the fastening screw Installation manual Planmeca Intra X ray unit 31 OTHER INSTALLATION ALTERNATIVES NOTE The ceiling arm shaft can be locked temporarily to ease the installation of the unit Tighten this locking screw _ amp Fastening screw Ceiladap6 eps Tigh
12. 39 OTHER INSTALLATION ALTERNATIVES NOTE The extension arm is not horizontal but its end is 2 mm over the horizontal level When the assembly is completed the weight of the unit bends the arm to horizontal position SN seh RN ene ee p a H a oa ae sw ss oh A Le d D 2 mm 2 mm ps 1_13A e Connect the grounding leads to the grounding point in the bottom of the adapter plate cover part earthing cable 40 Planmeca intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES Connect the arm cable and extension cable according to the figure below Note that it does not mat ter which way the yellow leads HV1 and HV2 are connected to the connectors HV1 and HV2 Extension cable max 12 m Extension cable Con nectors Gry 12V Arm cable Std Yel Grn Molex 3 Bik EXP Red KVC Brn GND Blu SCL Pink ELMP Generator PCB Molex 3 1 s 2 P1 Molex 6 1 2 3 P8 4 5 NC 6 Screw terminal q 12V_Gry GND Brn P14 ELMP Pink Ferrite Optional Ready light Connect the Dixi interconnection cable to the Panel mounted RJ45 modular adapter located on the base plate of the single stud assembly an
13. NDARD INSTALLATION TO A WALL on page 11 Generator box Control panel Remote assembly see section 7 REMOTE CONTROL PANEL INSTALLATION on page 48 Control panel Telephone cable Remote assembly with generator box see section 6 ATTACHING THE GENERATOR BOX WITHOUT THE ADAPTER PLATE on page 44 Single stud plate i i Fi 1 1 Ties G 1 i i i i i i i i Nay _front_3 e Tay Li Y Extension cable Installation manual Planmeca Intra X ray unit 9 INSTALLATION POSSIBILITIES Single stud assembly plate with control panel see section 5 3 Single stud installation on page 38 Control panel Generator box Lfront_4 eps Fixed control panel contains a possibility to make double exposure button assembly see section 8 FIXED CONTROL PANEL INSTALLATION on page 51 Double exposure button E b J ant Fixed control 1 i panel Generator box i li i f l i p i 7 i Telephone cable r ecceceeeeeeeeeen nennen 10 Planmeca intra X ray unit Installation manual STANDARD INSTALLATION TO A WALL 4 STANDARD INSTALLATION TO A WALL WARNING Ensure that the power supply is switched off before installing the Planmeca Intra X ray unit 4
14. Telephone cable Connect the cross connection part number 10007597 cable between the Extension cable PCB and fixed control panel Extension cable PCB Fixed control panel ps Intra_box4A e Cross connection cable 54 Planmeca Intra X ray unit Installation manual FIXED CONTROL PANEL INSTALLATION 8 4 Attaching the fixed control panel to the bottom plate In case the telephone cable is routed to the Extension cable PCB via the wall surface remove the cover from the right hand side knock out opening ps Intra_box7 e Press the fixed control panel to its position so that the mounting pins located on the bottom plate hit the mounting springs on the control panel Secure the control panel to its position with one attach ment screw ps Intra_box9 e Installation manual Planmeca Intra X ray unit 55 EXTERNAL EXPOSURE BUTTON 9 EXTERNAL EXPOSURE BUTTON An external exposure push button cable can be connected to the Generator PCB according to the figure below Generator PCB FSoa6 5 EEPB eps e e Disabling the exposure key on the control panel The exposure key on the control panel can be disabled as follows amp Enter the service mode Press and hold
15. aengaueds 10 Fixed control panel contains a possibility to make double exposure button assembly see section 8 FIXED CONTROL PANEL INSTALLATION on page 51 nesses 10 4 STANDARD INSTALLATION TO A WALL 0 ccceeeeeeeeeeeeeeeceeeeeeeeeeeeaaee ees eeeeeseeeeeeseaaeeseseeeeeseneeeeeseeeeneeas 11 4 1 Attaching the standard adapter plate to Wall eecceceeeeeeeeeeeeeeeeeeeeeeeaeeeeeseeaeeeeeseenaeeeeeeenaeeees 11 Attaching alternative 1 recommended for concrete or brick Wall eecceeeeesseeeeeeeeteeeeeeeeaaes 12 Attaching alternative 2 for wooden wall not recommended for concrete wall a e 14 4 2 Assembling the art lt 2 cevaisstadadeeniididiadinaiz asain ei cede ania aula dces 15 4 3 Changing the bracket arm movement area eeececeecceceeeeenee tees eeeeaeeeeeeeseaeeeeseaeeeseaeeseeaeeeseaeeees 16 4 4 Mounting the arm oe eeeecee cece ence eee eeeeee ee eee aaee eee eeaaeeeeeeaaaeeeeeeeaaeeeeeseaaeeeeseeeaeeeeesseneaeeeeeeeenaeeees 18 4 5 Installing the generator assembly 00 00 e eee e eee eeene eter eeeaeee eee eeaaeeeeteeaeeeeeeenaeeeeeeeesaeeeeeeeaaaes 18 4 6 Gonnecting the Cables siosana a ne ea AR a Aea e a Aa AAEE NESER aT ENa 20 ACAD eoe A e AE E eats E eens 20 Mains cable concealed wiring eesssssesessrssssrrnssssrrnnustnrnneernnnsttnnannnentanntntannnnenanannenaneneenanenna 20 4 7 Attaching the control panel holder to the generator housing ssessssssrissreriiesrerrsserrrrsserennes 22 4 8 Mo
16. aring to vertical position by opening slightly the mounting screws and turning the adjustment nuts to required position The wall adapter moves towards the wall when turning the nut counterclock wise Ins4 eps Finally tighten all the mounting screws 14 Planmeca Intra X ray unit Installation manual STANDARD INSTALLATION TO A WALL 4 2 Assembling the arm AN CAUTION Care must be taken when assembling the arm for not to damage the arm cable NOTE Normally the bracket arm does not turn above the extension arm In case you need to change the movement area of the bracket arm refer to section 4 3 Changing the bracket arm movement area on page 16 Route the arm cable and the Dixi interconnection cable through the extension arm shaft housing Assemble the bracket arm to the extension arm by pushing the bracket arm shaft into the housing Secure the bracket arm with the locking plate Route the cables through the extension arm and arm shaft Place the cover plug back to the end of the extension arm Bracket arm Extension arm Arm shaft housing P Extension E arm shaft 2 Dixi interconnection n cable y A Arm cable Locking plate joint1 eps Installation manual Planmeca Intra X ray unit 15 STANDARD INSTALLATION TO A WALL 4 3 Changing the bracket arm movement area NOTE Normally the bracket arm does not turn above the extension arm but the arm move
17. ation manual Planmeca Intra X ray unit 11 STANDARD INSTALLATION TO A WALL Attaching alternative 1 recommended for concrete or brick wall Mark the position of the left lower mounting hole to the wall on the height of 1120 mm 44 in Drill one 10mm 0 4 in 32 35 mm 1 25 in in depth hole and place the expansion anchor into it Make sure that the end of the anchor is under the wall surface but not more than 5 mm Hit the wedge of the anchor firmly to the bottom of the hole Remove the adjustment nuts from the three other mounting holes Attach the adapter plate to the wall with one of the fastening screws and adjust the plate exactly to horizontal position Adapter plate Adjustment nut Insert the drilling tool to one of the holes and drill the second hole using the drilling tool as a guide Unscrew the drilling tool and insert the second expansion anchor as described above replace the adjustment nut and attach the screw Spirit level Ins2 eps 12 Planmeca Intra X ray unit Installation manual STANDARD INSTALLATION TO A WALL Drill the two other holes Remove the adapter plate and place the expansion anchors into the last two holes Attach the plate to the wall with four M8x30 DIN 912 screws and 98 4 17 DIN 125 washers You can use two adjustment plates under the adapter plate Ins3 eps Adjustment plate optional Use the adjustment nuts and the adjustment plates with the screws a
18. ch the arm and the Delight operating light according to the figure below Make sure that the light cable is in the groove of the light arm pivot when attaching the power control assembly to the light Add some vaseline to the light arm pivot Route the light cable through the openings on the power control assembly and push the light arm pivot into the power control assembly opening Carefully push the light power supply cable into the groove of the light arm pivot Push the pivot through the power control assembly openings so that the assembly hits the pin located on the light arm Push the power supply cable into the power control assembly and rotate the power control assembly so that the pin in the light arm goes into the hole on the power control assembly Attach two spring bushings to the light arm pivot f Power control assembly a TN z N 03 5x13 DIN 7981 a 5 Ky J 4 DIN 6798 M6x12 DIN 912 ight_AC_ceiling_inst_07 eps Intra_delit M 6x17 DIN 7991 7 V Spring bushings ee pring g Y SAN XQ NOTE Do not tighten the ligth cable but leave it a bit loose Connect the Delight wires according to the instructions given in Delight Installation manual publica tion number 588200 36 Planmeca Intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES 5 2 Adjustable ceiling adapter Concrete ceiling Mark the place of the adapter plate
19. ct documentation this publication should not be regarded as an infallible guide to current specifications We re serve the right to make changes without prior notice COPYRIGHT PLANMECA 2008 03 PUBLICATION PART NUMBER 10006030 revision 11 Installation manual Planmeca Intra X ray unit 1 PRE INSTALLATION REQUIREMENTS 2 PRE INSTALLATION REQUIREMENTS 2 1 Environmental requirements Wall construction The wall construction must be able to resist a shear load of 75 kg 170 pounds and withdrawal force of 200 kg 445 pounds at each of the four attachment locations Otherwise some additional mount ing supports must be used to fulfill this requirement Temperature amp humidity The operating temperature range is from 15 C to 35 C non condensing The acceptable humidity range is from 25 to 75 The storage temperature range is from 5 C to 60 C NOTE If the X ray unit has been stored at temperatures below 10 C for more than a few hours time must be allowed for the X ray unit to reach the room temperature before connecting it to the mains voltage 2 2 Electrical requirements Mains voltage The Planmeca Intra X ray unit has been preset at the factory to one of the 3 different mains voltage settings Please check that the rating indicated on the type shield and the mains voltage selector on the generator PCB connector P4 corresponds to the local mains voltage The possible voltage set tings are 100V
20. d secure the cable to the single stud wall plate with the cable clamp as shown on the figure below singlestud_A eps O Q L o Q Dixi interconnection cable NOTE The Dixi digital intra X ray system is installed according to the instructions given in the Dixi digital X ray systems installation manual Installation manual Planmeca Intra X ray unit 41 OTHER INSTALLATION ALTERNATIVES If the control panel is attached to the single stud cover attach the control panel holder before attach ing the cover to its position Drill two attachment holes to the cover as shown on the figure below and attach the holder to the cover with the two PT 3x22 rst WN1451 screws Comm _ 3 5mm Screw 3x22 PT Code 00326195 ps l_14 e Installation manual 42 Planmeca Intra X ray unit OTHER INSTALLATION ALTERNATIVES Connect the exposure warning indicator light cable to the connector P4 on the Extension cable PCB and attach the cover part earthing cable to the connector on the cover Attach the cover to position with one attachment screw and slide and the upper cover plate to its position ps 1 12A e Upper cover plate Cover Exposure warning indicator light cable e Earthing cable 5 4 Installation to the Planmeca Compact dental unit Install the Planmeca Intra X ray unit to the Planmeca Compact dental unit according to
21. down the select key for 4 seconds Press and hold down the Mode key for more than 2 seconds until the four uppermost prepro grammed setting indicator lights come on Press the parameter adjustment up key until the parameter number 18 appears on the kV display 38 Y O Parameter adjustment up key kV 0 The number indicating the mode of exposure key operation is shown on the time display 0 expo s sure key normal operation 1 exposure key operation disabled The factory default is 0 Press the Select key until the number starts to blink and the value can now be changed with the parameter adjustment keys Select the number 1 Accept the number 1 setting by pressing the Select key Press the Mode key briefly to exit the service mode 56 Planmeca Intra X ray unit Installation manual ATTACHING THE LONG CONE AND RECTANGULAR COLLIMATOR OPTIONAL 10 ATTACHING THE LONG CONE AND RECTANGULAR COLLIMATOR OPTIONAL The long cone is attached into its position by pushing it into the short cone and rotate it so that the red point on the short cone and the black point on the long cone are in line Attach remove red In position red and points in line black points in line The rectangular collimator can be attached to the long cone either before the film holder or after it Refer to the Planmeca Intra X ray unit s user s manual for detailed instructions on how to use the rectangular c
22. e control panel holder can be attached with a sticker to a surface which can NOTE not be drilled e g glass 50 Planmeca intra X ray unit Installation manual FIXED CONTROL PANEL INSTALLATION 8 FIXED CONTROL PANEL INSTALLATION 8 1 Attaching the bottom plate NOTE In case you are using a wall socket attach the bottom plate according to instructions given in section 8 2 Attaching the bottom plate to the wall socket on page 52 Use the bottom plate as a template and mark the positions of the holes for the four attaching screws to the wall Bottom plate ps Intra_box1 e If the wall is made of concrete or brick drill 6 mm 0 23 in 32 35 mm 1 25 in in depth holes and place the expansion anchors into them If the wall is made of wood attach the screws to the wall without drilled holes Do not use the expansion anchors with wooden or plaster wall Use 4 attaching screws Expansion anchor Note Do not use expansion anchors with wooden plaster wall 24x30 DIN 7981 ps Telephone cable ee p Intra_box2 e Installation manual Planmeca Intra X ray unit 51 FIXED CONTROL PANEL INSTALLATION 8 2 Attaching the bottom plate to the wall socket You can also attach the bottom plate to the wall socket as shown on the figure below Alternative 1 Wall socket Alternative 2 ps
23. eeeee esses eeeeeeeeeeeeeeeseeaeeeesesaeeeseeeeeseeneeeneeas 51 8 1 Attaching the bottom plate sorginen e n ea a EA NAE A AEAEE 51 8 2 Attaching the bottom plate to the wall socket e ssssssseesssissesirissrrirtsstirntsstinnntntinnnntnnnnnennn nnne 52 8 3 Connecting the cables 0 2 eeecceeee cece ee eeee etter eeeeaeeteaeeeeeaeeeaaaeeseaaeeseaaeeeeeeeseaeeeseeeeseneeeeeeeneeees 53 8 4 Attaching the fixed control panel to the bottom plate oo eeceeeeeeeeneeeeeeeeeeeeeeeeeaeeeeeenaaeee 55 9 EXTERNAL EXPOSURE BUTTON milad a raana aaar eea ara daaa araea a aaeeea aaiae aani 56 Disabling the exposure key on the Control panel eee ceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeeeeenaeeeeeeeaeaees 56 10 ATTACHING THE LONG CONE AND RECTANGULAR COLLIMATOR OPTIONAL siec 57 TT FINAL ADJUSTMENTS erara aara aaao aaaea cvasteedsiecededddacaveust Ueastencecsdcieauxsuctesdvsdaesastuen Aaa ddae atnda ia cussed 58 11 1 Adjusting the balance of the AFM eect eeeeneeeee cence ee eeeaaaeeeeeeeaaeeeeeesaeeeeeeeeeaeeeeeeeeeeeeeneeeaas 58 11 2 Adjusting the bracket arm angles 0 eee ee eeneeeeeeeeneeeeeeeneaeeeeeeeaaeeeeeeeaaeeeeeesnaeeeeetesaeeeeeeenaaaes 59 11 3 Adjusting the stiffness of the tube head s horizontal axle oo eeeeeeeeeeeneeeeeeeeneeeeeeeeaaeeeeeeeaas 60 12 RUNNING IN THE X RAY UNIT cscsecesssceciiecectcccccensevccnecssteeneeccewedecnbeseccettenntiseeestineesccneersnieessscueresenesteene 61 TOC 2 Installation manual INTRODUCTION
24. installation pattern or the single stud adapter plate as a template and mark the positions where the holes for the attaching screws will be drilled If the wall is made of concrete or brick drill 10mm 0 4 in 32 35 mm 1 25 in in depth holes and place the expansion anchors into them If the wall is made of wood drill 95 mm 0 2 in 55 60 mm 2 2 in in depth holes for the attachment screws Do not use the expansion anchors with wooden wall Attach the adapter plate to the wall with at least three M8x80 DIN 571 screws and the 98 4 DIN 125 washers Route the extension cable through the opening on the adapter plate Qa o lt ee z 9 lt a 2 g Single stud adapter oe ee a 9 f F p 97 p al 5 r S J or a WE SAAS or o f 2 oe Optional as p Y Assemble the bracket arm to the extension arm refer to the section 4 2 Assembling the arm on page 15 38 Planmeca intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES Route the arm and Dixi interconnection cables through the wall adapter bearing Mount the arm into position by pushing the arm shaft into the wall adapter bearing Using a spirit level adjust the arm position with the four screws of the wall adapter bearing E D IO gt Z M k Adjust the arm position with these screws Installation manual Planmeca Intra X ray unit
25. it In some countries an additional external fault current guard is also required Grounding The Planmeca Intra X ray unit must always be connected to a grounded outlet to fulfill the safety directives stated Power consumption The idle power consumption is less than 30VA Maximum power consumption is 1000VA and occurs during the exposure maximum exposure time is 3 2 seconds Installation manual Planmeca Intra X ray unit 3 INSTALLATION POSSIBILITIES 3 INSTALLATION POSSIBILITIES 3 1 Mounting alternatives NOTE The Planmeca Intra X ray unit can be installed in several ways Read these installation instructions carefully because some installation accessories are optional and are not included in the standard delivery Make sure that required accessories are available before starting the installation NOTE The following cables are used in some installations described in this sec tion EXTENSION CABLE 1pcs protective earth min 1 0 mm AWG 18 4 pcs signal wires min 1 0mn AWG 18 4 pcs signal wires min 0 5 mm AWG 20 rated 300 V flexible TELEPHONE CABLE ordinary 6 pole telephone cable AWG 24 Standard wall mounting in treatment room see section 4 STANDARD INSTALLATION TO A WALL on page 11 ps i Control panel ie gt extension i ei ey arm 835mm i r 1975 Dental unit extension arm 760mm oe r 1900 IR1_1 e al extension arm 535mm extension arm 385mm r 1525
26. it 19 Installation manual STANDARD INSTALLATION TO A WALL 4 6 Connecting the cables AN WARNING Ensure that the power supply is switched off before connecting the cables Arm cable Connect the grounding lead of the arm cable to the grounding point located on the right side of the generator assembly Connect the control leads of the arm cable 6 pole connector to the terminal P8 on the generator PCB Connect the power leads 3 pole connector of the arm cable to the termi nal P1 on the generator PCB Snap the ferrite to the arm cable as shown on the figure on next page Mains cable concealed wiring In the case that mains voltage is supplied via concealed wiring route the mains cable between the adapter plate and the generator assembly Connect the grounding lead to the grounding point next to the mains switch Connect the neutral wire to the mains input terminal P5 marked N Connect the live wire to the mains input terminal P5 marked L Generator PCB version C or later from X ray unit s serial number IXRF58018 When the con cealed wiring is used the cable coming from the ON OFF switch to the connector P7 must be moved to the connecto P10 Also the fuse F3 must be removed MAINS N Neutral Line Blue Brown ROM MAINS SWITCH Blue Brown Y Remove Fuse F3 20 Planmeca Intra X ray unit Installatio
27. ith remote control in treatment room see section 7 REMOTE CONTROL PANEL INSTALLATION on page 48 ccccceeeeeeeeeeee cece eeeeeeeseaeeeteaeeeseneeeteneeeseaees 5 Ceiling mounting in treatment room see section 5 1 Ceiling installation on page 25 6 Dental unit mounting in treatment room only Planmeca Compact dental unit see Planmeca Compact installation manual ccceeeeeeeee cence eeeeeeeeeeeeeeeeeeeaeeeeeaeeeteaaeeseaeeees 7 X ray room with generator box control panel outside the room see sections 7 REMOTE CONTROL PANEL INSTALLATION on page 48 and 5 3 Single stud installation ON page 38 cceceeeceeeeeeeeeeeeeeeeeeeeeeeeaeesteaeeeseaeeeseeeeeseaeesseeeeeeaaes 8 3 2 Control panel assembling alternatives 0 cccceeccceceeeeeeeneeeeeeeeeeeeeeeeeeeeseeeseaeeesseaeesseeeeneneeesenaes 9 Standard assembly see section 4 STANDARD INSTALLATION TO A WALL on PAGS ccetegeaiacs pepsi a beni dat oa an eneeseal hd piegisean Helena soe ceed eee 9 Remote assembly see section 7 REMOTE CONTROL PANEL INSTALLATION on PAGS AS oiaro a E E A E I nimi nine iu ates 9 Remote assembly with generator box see section 6 ATTACHING THE GENERATOR BOX WITHOUT THE ADAPTER PLATE on page 44 s sssssssesrisssrserrrsrrirsrirsrirnsrrntsrnnerrnserrnene 9 Single stud assembly plate with control panel see section 5 3 Single stud installation on PAGS BB onna ETE a T OE E E eacgiemp
28. me to the wall with two 4x30 DIN 7981 screws to the wall without drilled holes Do not use the expansion anchors with wooden or plaster wall Possible through holes for the cable Route the telephone cable through the hole on the side or bottom of the frame Assemble the data wall socket according to the figure above 48 Planmeca Intra X ray unit Installation manual REMOTE CONTROL PANEL INSTALLATION Connect the telephone cable according to the figure below O Generator PCB Install the holder attachment plate to the wall with two 4x30 DIN 7981 screws If the wall is made of concrete or brick drill 6 mm 0 23 in 32 35 mm 1 25 in in depth holes and place the expan sion anchors into them If the wall is made of wood attach the screws to the wall without drilled holes Concrete wall a ai Wooden wall m p oe N 04x30 DIN 7981 screw Expansion anchor a P g A Holder attachment plate lt Installation manual Planmeca Intra X ray unit 49 REMOTE CONTROL PANEL INSTALLATION Press the control panel holder to the attachment plate Attach the control panel to the holder and connect the control panel cable to the control panel and to the wall socket Q ox oO oO _ 22 c Th
29. ment area can be changed by moving the limiting pin on the extension arm shaft housing The factory preset and modified movement areas are shown on the figures below THE LIMITING PIN POSITION CAN BE CHANGED BUT THE PIN MUST NOT BE REMOVED y aly hy Factory preset movement area Tae ae intral eps 6 a opening Pin Modified movement area Gos Arm movement obstructed N intra2 eps QE Empty opening NOTE When the modified area is used the tube head can hit the extension arm Be careful not to knock the tube head against the arm 16 Planmeca intra X ray unit Installation manual STANDARD INSTALLATION TO A WALL Unscrew the two screws that hold the housing on the extension arm and remove the shaft joint2 eps Arm shaft housing Remove the limiting pin from the housing by using a thin screwdriver and hammer joint3 eps Attach the pin to the other opening on the housing so that the pin is level with the inner surface of the housing see figure below Limiting pin a Housing surface MODIFIED PRESET joint4 eps Openings for limiting pin Installation manual Planmeca Intra X ray unit 17 STANDARD INSTALLATION TO A WALL 4 4 Mounting the arm Route the arm and Dixi interconnection cables through the wall adapter bearing Mount the arm into position by pushing the arm shaft into the wall adapter bearing The arm position is adjus
30. n manual STANDARD INSTALLATION TO A WALL NOTE In case the X ray units own power supply cable and the strain reliefer are removed from the generator assembly mains voltage is supplied via con cealed wiring cover the opening with a plug supplied with the X ray unit Connect the Dixi interconnection cable to the Panel mounted RJ45 adapter located beside the on off switch and secure the cable with the cable clamp If needed attach the cable to the wall adapter bearing with a cable tie e of Lillo SH i a eal ps _tech_3APSU2 e Snap on ferrite NOTE The Dixi digital intra X ray system is installed according to the instructions given in the Dixi digital X ray systems installation manual Installation manual Planmeca Intra X ray unit 21 STANDARD INSTALLATION TO A WALL 4 7 Attaching the control panel holder to the generator housing Drill two 3 5 4mm 0 14 0 16 in holes for the control panel holder to the generator housing The hole positions are marked to the inner side of the cover with collars Generator housing ins14 eps Attach the control panel holder to the generator housing with the t
31. nit Installation manual INSTALLATION POSSIBILITIES Dental unit mounting in treatment room only Planmeca Compact dental unit see Planmeca Compact installation manual NOTE Only short extension arm can be used in dental unit mounting x I e IR4 eps Generator Extension cable max 12m Control panel Dental unit porn rence nn nn nse nnn n nnn nnnne i D Installation manual Planmeca Intra X ray unit 7 INSTALLATION POSSIBILITIES X ray room with generator box control panel outside the room see sections 7 REMOTE CONTROL PANEL INSTALLATION on page 48 and 5 3 Single stud installation on page 38 g Remote control panel 7 le extension arm 835mm peer r 1975 ps pee cwcccenwocccescesceescnccesccnceesccccescccccoscccccescccccescccccesce extension arm 760mm r 1900 std IR5_1 e Telephone cable max 12 m extension arm 535mm r 1675 std extension arm 385mm r 1525 es extension arm 835mm r 1975 ps extension arm 760mm r 1900 IR6_1 e extension arm 535mm r 1675 std Extension cable max 12m extension arm 385mm r 1525 aay rs 8 Planmeca Intra X ray unit Installation manual INSTALLATION POSSIBILITIES 3 2 Control panel assembling alternatives Standard assembly see section 4 STA
32. ollimator and the film holder Rectangular collimator Film holder Installation manual Planmeca Intra X ray unit 57 FINAL ADJUSTMENTS 11 FINAL ADJUSTMENTS 11 1 Adjusting the balance of the arm Adjust the balance of the arm by turning the adjustment nuts with a screwdriver The adjustment nuts are located inside the bracket arm and can be reached through the openings at the under side of the bracket arm t Openings for adjustments gt Arm in adjustment position NOTE Adjust the arm from the lower part of the adjustment nut WRONG 58 Planmeca Intra X ray unit Installation manual FINAL ADJUSTMENTS 11 2Adjusting the bracket arm angles In case the bracket arm angles need to be adjusted it can be done with the limiting plates Remove the cover plug from the end of the bracket arm Attach the limiting plate to the arm with the two M3 Allen screws Adjust the angle with the limiting plate adjustment screws Intradj1 eps Limiting plate Limiting plate adjustment screw Intradj2 eps Installation manual Planmeca Intra X ray unit 59 FINAL ADJUSTMENTS 11 3Adjusting the stiffness of the tube head s horizontal axle Remove the plug from the tube head s axle and adjust the tightness of the two adjusting screws evenly arrows on the figure below Adj_stiffness eps
33. rews to the holes and slip the generator assembly under the heads of the screws WARNING Ensure that the power supply is switched off before connecting the cables In the case that mains voltage is supplied via concealed wiring route the mains cable as shown on the figure below NOTE In case the X ray units own power supply cable and the strain reliefer are removed from the generator assembly mains voltage is supplied via con cealed wiring cover the opening with a plug supplied with the X ray unit Connect the grounding lead of the power cable to the grounding point next to the mains switch Con nect the neutral wire to the mains input terminal P5 marked N Connect the live wire to the mains input terminal P5 marked L Connect the grounding lead of the extension cable to the grounding point located on the right side of the generator assembly Connect the control leads of the cable 6 pole connector to the terminal P8 on the generator PCB Connect the power leads 3 pole connector of the cable to the terminal P1 on the generator PCB Snap the ferrite to the extension cable as shown on the figure below Extension cable Power ee NT E By Ins10APSU2 eps Installation manual Planmeca Intra X ray unit 45 ATTACHING THE GENERATOR BOX
34. t each corner of the adapter plate Adjust the wall adapter bearing to vertical position by opening slightly the mounting screws and turning the adjustment nuts to required position The wall adapter moves towards the wall when turning the nut counterclockwise Ins4 eps Finally tighten all the mounting screws Installation manual Planmeca Intra X ray unit 13 STANDARD INSTALLATION TO A WALL Attaching alternative 2 for wooden wall not recommended for concrete wall Use the installation pattern as a template and mark the positions where the holes for the four attach ing screws will be drilled Use a spirit level to ensure that the adapter plate will be level If the wall is made of concrete or brick drill 10mm 0 4 in 32 35 mm 1 25 in in depth holes and place the expansion anchors into them Attach the adapter plate to the wall with the four M8x30 DIN 912 screws and the 98 4 DIN 125 washers If the wall is made of wood or plaster drill 5 mm 0 2 in 55 60 mm 2 2 in in depth holes for the attachment screws Do not use the expansion anchors with wooden or plaster wall Attach the adapter plate to the wall with the four 8x80 DIN 571 lag screws and the 08 4 DIN 125 washers You can use two adjustment plates under the adapter plate Ins16 eps Adjustment plate optional Use the adjustment nuts with the screws at each corner of the adapter plate Adjust the wall adapter be
35. ted at the factory In case the position needs to be adjusted loosen the adjustment piece fastening and adjustment screws Do not open the screws totally Turn the arm away from the wall Tighten the adjustment screw the adjustment piece moves towards the arm shaft Turn the arm carefully to the desired position If the arm remains too far from the wall push the arm slightly towards the wall and simultaneously loosen the adjustment screw The adjustment piece now moves away from the arm shaft and the arm towards the wall After the desired position has been reached tighten the adjustment piece fastening screw with care Tighten also the adjustment screw Fastening screw Adjustment screw Walladap eps wall Wall adapter and arm seen from below 4 5 Installing the generator assembly There are four M4x8 ULS screws attached to the adapter plate at the factory Loosen these screws a couple of turns with a 2mm allen key Position the arm cable and mains cable as shown on the figure below Slip the generator assembly under the heads of the screws Wall adapter bearing Mains cable O oO oO fe O s fed n n oO 3 S eps Arm cable 18 Planmeca Intra X ray unit Installation manual STANDARD INSTALLATION TO A WALL Secure the generator assembly into position by tightening the four screws through the openings on the generator PCB sdeznSdvgsul Planmeca Intra X ray un
36. ten firmly Intra ceil adap assy 7 050397 32 Planmeca Intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES Generator PCB P1 l l l l ps l l l P14 l I Route the arm and Dixi interconnection cables from the extension arm to the ceiling arm In case the Dixi digital intra X ray system is not installed leave the Dixi interconnection cable into the ceiling arm as shown on the figure below Dixi interconnection cable Arm cable wae _ W aij J Ceiladap8A eps NOTE The Dixi digital intra X ray system is installed according to the instructions given in the Dixi digital X ray systems installation manual Connect the cables according to the figure below Note that it does not matter which way the yellow leads HV1 and HV2 are connected to the connectors HV1 and HV2 Extension cable max 12 m l Extension l Arm cable Std cable Con nectors T Yel Grn Molex 3 Yel HV4 Molex 3 2 Naa s Wht HV2 i SS Psat afo Molex 6 Hva o i 1 Gry 12V mist l A Bik__ EXP deao gt aux Jo 3 Red KVC jaue aes i 7 Brn GND kve E fe p7 GND a Blu SCL Ieee testo e8 Wace Pink _ELMP Jere E lo S O O Screw ee terminal q 12V Gry 5 GND Brn 3
37. the instruc tions given in dental unit installation manual publication number 10006961 Installation manual Planmeca Intra X ray unit 43 ATTACHING THE GENERATOR BOX WITHOUT THE ADAPTER PLATE 6 ATTACHING THE GENERATOR BOX WITHOUT THE ADAPTER PLATE NOTE The generator box is attached to the wall without adapter plate in ceiling single stud and dental unit installations NOTE Use the extension cable supplied with the unit between the X ray unit and generator box Note that the connectors of the cable must be connected to the generator box and the cable wires to the Extension cable PCB In the case that concealed wiring is used the mains cable and extension cable outlet should be positioned next to on the right hand side the adapter plate Use the generator assembly as a template and mark the positions of the holes for the four attaching screws to the wall If the wall is made of concrete or brick drill 6 mm 0 23 in 32 35 mm 1 25 in in depth holes and place the expansion anchors into them If the wall is made of wood or plas ter attach the screws to the wall without drilled holes Do not use the expansion anchors with wooden or plaster wall Wooden plaster wall Concrete brick wall Expansion anchor 24x30 DIN 7981 Power cable Extension cable Ins8APSU2 eps 44 Planmeca Intra X ray unit Installation manual ATTACHING THE GENERATOR BOX WITHOUT THE ADAPTER PLATE Insert the sc
38. to the ceiling Drill six 10 mm 0 4 in 32 35 mm 1 25 in in depth holes and place the expansion anchors into them Insert the expan sion anchors into the holes Attach the upper part of the adapter to the concrete ceiling with six M8x30 DIN 912 screws and 8 4 17 DIN 125 washers Wooden ceiling Attach the upper part of the adapter to the wooden ceiling with six 8x80 DIN 571 lag screws Do not use the expansion anchors with wooden ceiling Adjust the height of the ceiling adapter so that the lower plate of the adapter is on a level with the ceiling Lock the lower part to the upper part with the eight M8x16 DIN 912 screws and M8 DIN 934 nuts Attach the standard adapter plate to the adjustable ceiling adapter with four M8x30 DIN 912 screws and 8 4 17 DIN 125 washers Use the adjustment nuts and the adjustment plates with the screws at each corner of the adapter plate Continue the installation according to the instructions given in section 5 1 Ceiling installation on page 25 Upper part of the adjustable adapter Intra ceil adj adapter 020597 Lower plate of the adjustable adapter Adapter plate Installation manual Planmeca Intra X ray unit 37 OTHER INSTALLATION ALTERNATIVES 5 3 Single stud installation NOTE Use the single stud assembling plate when you are installing the Planmeca Intra to a cabinet to an end of a wall or to a single stud plaster wall Use the
39. unting the generator housing sssssssesssrsressrnnessrrrnsstnnrnntnnnnantttnnenttnannnenanennetaneantnnnneennnn nae 23 4 9 Connecting the control panel cable cccceceeeeceeeeeeeeeeeceeeeeeeeeeeaeeeeeaeeeecaeeeeeaeeseaeeeseaeeseeeeeneees 24 5 OTHER INSTALLATION ALTERNATIVES c ccceeeeeeeseeeeeeeceeeeeeeeeeesaaeeeeseeeeeeeeeeeesaaeeeesaaeeeeeeeeeeeseeeeeeees 25 5 1 Ceiling installation e eie etaa aa a a vests tees ees ten Eea tesla Ae aaraa AEA aa eA ANEN tebe 25 C n rete Ceiliig vst ei ia ae ea ES ee a es 25 Installation manual TOC 1 TABLE OF CONTENTS Wooden Ceiling derari R saa E Aaa aA ae e duebdeta penal 26 Delight operating light installation esssseesssseesesrrresenrrnesssrnnestrnnantrnnnantnnnnanennnnantnananenannacena nnne 35 5 2 Adjustable celling Adapter cesesianssnnnare a i aen east dane ae e anah SeA devas daneenbuetanereebedie gs 37 5 3 Single stud installation 0 2 ee cece eceneeeeeeeeeeeeeeeeaeeeecaeeeeeaeeeaaeeseeaeeseaaeeseaeeeseaeeeseeeeseueeeeeeeneeees 38 5 4 Installation to the Planmeca Compact dental unit ccceceeeeeeeeeneeeeeeeeeeeeeeeeeneeeeeaeeeeteeeeseaeeees 43 ATTACHING THE GENERATOR BOX WITHOUT THE ADAPTER PLATE 2 2csecceeeseeeeeeseeeeeeeeeeeeeeeeeens 44 REMOTE CONTROL PANEL INSTALLATION c cceceeeceeeeeeeeeeeeeeeeeeeeeseseeeeeseeeeeeseaaeseesseeeeseeeeesseeaeeeeees 48 8 FIXED CONTROL PANEL INSTALLATION cccesececeeseeeeeeeeeeee
40. wo PT 3x22 rst WN1451 screws A gt Generator housing 2 AA lt gt Be ra ee A 4 4 A ge a Q 2 gt 2 4 z a Z Pad gt ay Ins15 eps Control panel holder 22 Planmeca Intra X ray unit Installation manual STANDARD INSTALLATION TO A WALL 4 8 Mounting the generator housing Place the generator housing over the generator assembly Secure the cover into position with the three M4x6 ULS screws Generator housing cover plate Installation manual Planmeca Intra X ray unit 23 STANDARD INSTALLATION TO A WALL 4 9 Connecting the control panel cable Connect the control panel cable to its terminal at the underside of the generator box Control panel cable 24 Planmeca Intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES 5 OTHER INSTALLATION ALTERNATIVES AN WARNING Ensure that the power supply is switched off before installing the Planmeca Intra X ray unit NOTE With the installation methods described in this section the generator box is installed directly to a wall without using a wall adapter plate Refer to the section 6 ATTACHING THE GENERATOR BOX WITHOUT THE ADAPTER PLATE on page 44 5 1 Ceiling installation Concrete ceiling Mark the place of the adapter plate to the ceiling Drill one 10 mm 0 4 in 32 35 mm 1 25 in
41. ws of the lower ring on the upper edge S Note that the attachment screws of the upper Ceiling arm QE NOTE If the optional adapter cover is used attach it to its position before attach ing the ceiling arm Adapter cover Ceiling arm Installation manual Planmeca Intra X ray unit 27 OTHER INSTALLATION ALTERNATIVES Install the ceiling arm to the adapter as follows If the operating light is installed to the ceiling arm position the arm according to the figure below opening away from the chair 500 mm Opening NOTE The ceiling arm is locked to the arm adapter by making a dent with a mounting ring screw to the arm above the adapter collar The dent must not be in line with the machining on the adapter collar ceill eps Arm adapter Machining Adapter collar Mounting rings Ceiling arm 28 Planmeca Intra X ray unit Installation manual OTHER INSTALLATION ALTERNATIVES Attach the ceiling arm to the adapter with the upper mounting ring Ceil2 eps Move the lower mounting ring to the position shown on the figure below With the locking screw located on the lower mounting ring make a dent to the arm the head of the locking screw differs from the head of the normal attachment screws This will lock the arm to the adapter Replace the locking screw with an attachment screw 30 3
Download Pdf Manuals
Related Search