User Manual
Contents
1. menu WDR Setup VALUE1 3 VALUE2 3 CONTRAST LOW RETURN WDR Value setting Press left right to adjust the valuel from 0 to 7 Valuel means the intensity of back scene Press left right to adjust the valuel from 0 to 7 Value2 means intensity of front light WDR Contrast Press left right to adjust the WDR contrast After settings move the cursor to RETURN and press confirm button to return to the previous menu 3 2 6 D N Settings Press up down to move the cursor to D N and press left right to select item from Day Night 1 Auto2 18 Autol Setting Select Autol and press enter to go into the submenu AUTO D N 1 VALUE 7 D gt N 3S N gt D 3S IR SET ETURN Press up down to move the cursor to VALUE and press left right to select value from 0 to 7 Move cursor to D gt N and press left right to select the switch time including 3S 5S 10S 15S 20S 25S or 30S Move cursor to N gt D and press left right to select the switch time including 3S 5S 10S 15S 20S 25S or 30S After settings move the cursor to RETURN and press confirm button to return to the previous menu Press up down to move the cursor to IR SET and press left right to select ON or OFF Note When IR SET is ON the camera turns on the ICR stabilization function If the camera turns to Night mode twice in 10 minutes the camera will go t2. C CS mount Auto Iris Lens DC Video Drive Day Night IR Cut Filter Auto Switch Horizontal Resolution TVL 540 Color 600 B W Wide Dynamic Range 160X Synchronization Internal Power synchronization Video Output 1Vp p Composite Output 75Q BNC S N Ratio More than 50dB Camera ID On Off 15 letters adjusted position Auto Gain Low Middle High Off D N Mode Autol Auto2 Day Night Auto White ARDA Auto trace WB1 Auto trace WB2 Manual Auto Private Mask On Off Maximum 8 Zones Menu Motion Detection Mode 1 Mode 2 Off Flicker Proof On Off RS 485 Address Protocol Baud Rate Language English Chinese Gamma Amendment Digital Zoom Digital Noise Reduction Video POS NEG Mirror Resolution Aperture Y C Blemish Detection Power Supply 24V AC 20VA 10 12VDC 300Ma 10 Working Temperature 10 C 60 C 14 F 140 F Power Consumption 4W 10W MAX With ICR Working Dimension mm 68 x 57 x 144 8 2 7 x 2 2 x 5 7 Weight C support AC100V AC240V 500g 1 11bs 27 Table 2 DS 2CC577P A Parameter Model Image Sensor DS 2CC577P A 1 3 inch SONY vertical double density interline CCD Signal System PAL Effective Pixels PAL 752 H x 582 V Min Color 0 1Lux F1 2 0 0003Lux F1 2 sensitivity x 256 Illumination B amp W 0 01Lux F1 2 0 0000
3. Manual WB setting is as below Select Manual and the menu will display on the screen Manual WB Temp INC RETURN Press up down to Temp and press left right to adjust the value of temperature After settings move the cursor to RETURN and press confirm button to return to the previous menu 3 2 4 BLC Settings Press up down to BLC WDR and press left right to select BLC and the menu will display on the screen BLC Setup AREA SET VALUE 3 RETURN Move cursor to AREA and press left right to set the BLC area as up down left right middle or manual then the BLC area is on the screen BLC area s setting step is as following Move cursor to SET and press enter to confirm and go to the submenu 17 BLC Area AREA OK RETURN Move cursor to AREA and press enter to select OFF LOC or area size Press enter to confirm the location and press up down to set the area s location Press enter to confirm the area size and press up down to set BLC area s size After settings move the cursor to RETURN and press confirm button to return to the previous menu Note When AREA is not OK press up down left right not to move cursor 3 2 5 Super WDR Settings Move cursor to BLC WDR and press left right to select WDR then press enter to go to WDR operation
4. APERTURE Move cursor to APERTURE and press left right to set the aperture value from 0 to 7 Y Means brightness is adjustable from 0 to 7 C Means saturation is adjustable from 0 to 7 PRIVACY Move cursor to PRIVACY press enter and the menu will appear on the screen Privacy Mask ZONE 1 ON OFF OFF SET OK COLOR 7 MOSAIC OFF RETURN Move cursor to ZONE to select the number of privacy mask And there are 8 zones in total Move cursor to ON OFF and press left right to select ON Move cursor to SET and press enter to edit mask and size as gt order a Select LOC and move the gray optional color quadrate area to expected position then press enter b Select AREA and press up down left right to control the size of mask area c Repeat above operation to set other mask area Move the cursor to COLOR there are 8 colors can be selected After settings move the cursor to Return and press confirm button to return to the previous menu RS485 Set protocol baud rate and address before use RS 485 to control camera Move cursor to RS485 press enter and the menu will appear on the screen 25 RS485 Setup ADDRESS 000 PROTOCOL PELCO D BAUDRATE 9600 RETURN Note This function is invalid for DS 2CC577P A Address Move cursor to Address press left right to set the number
5. and press left right to select the lens type as ELC or ALC ELC adopts auto electronic shutter to adjust the brightness ALC adopts auto iris to control lens of camera adjustable Note ELC auto shutter fixed iris ALC auto iris fixed shutter Select ELC and press confirm then the ELC Setup menu will show on the screen of the monitor ELC Setup VALUE L H RETURN Press up down to move the cursor to the VALUE press left right to adjust brightness move the cursor to RETURN and press confirm button to return to the previous menu Note Different values indicate the different brightnesses Select ALC and press confirm then ALC Setup menu will show on the monitor ALC Setup VALUE L H RETURN Move the cursor to VALUE press up down to adjust the menu After settings move the cursor to and press confirm button to return to the previous menu 16 3 2 3 WB Settings Press the cursor to WB then press left right to select the item from ATW1 ATW2 Auto or Manual ATWI Camera recover color automatically according to the environment color temperature temperature range is approximate from 2500K to 6500K ATW2 Temperature range is approximate from 2500K to 15000K ATC Adjust under steady color temperature environment After selecting ATC the white balance will take effect to the current scene Manual Adjust red and blue values to setup white balance
6. external trigger command 3 RS 485 support RS 485 control support connecting DVR keyboard and etc to realize remote control 4 Video Output output 540TVL super high resolution analog video 5 Double power supply design support 12VDC and 24VAC 6 POWER Power supply indicator the LED light will turn on as the power supply is proper 7 GND 1 4 Dome Camera Appearance Tesi Power Supply ff DC12V AC24V TTE e i Mounting Hole lt Video Output y 1 di Side Shield TERNA m 5 E gt N gt PA Dome Cover SOM _A Fig 1 4 Dome Camera Appearance 3 axis adjust Pan Rotation Range 0 355 Tilt Rotation Range 0 90 support installation at different angles 1 5 IR Control Note This function is only valid for DS 2CC577P A Up Menu Right Left 5 Down Fig 1 5 1 IR Remote Menu Press this button for 3 seconds to enter the camera main menu and press Menu in camera main menu to enter the sub menu interface Up Move cursor upward Down Move cursor downward Left Move cursor leftward Right Move cursor rightward Note The other function keys are not available by now CHAPTER2 Installation Before mounting please make sure that the device in the package is in good condition and all the assembly parts are complete Note The lens weight must be less than the 1kg CS assembly After in
7. optional from 0 to 254 Protocol Move cursor to PROTOCOL and press enter to select PELCO P or PELCO D Note Controller must set corresponding protocol and baud rate with camera to control the camera Baud Rate Move cursor to BAUDRATE and press enter to select baud rate from 1200 4800 9600 19200 bps SYSTERM INFORMATION Press enter to check the hardware software and DSP information And this information is established for maintenance or modification in the future After settings move the cursor to Return and press confirm button to return to the previous menu 3 2 12 Exit Setting Move cursor to EXIT and press left right to select the way of exit from SAVE CANCEL and DEFAULT Then press enter to exit the menu CANCEL Press enter to cancel the setting parameter and exit the menu SAVE Press enter to save the setting parameter and exit the menu DEFAULT Press enter to restore the factory default value and exit the menu 26 Appendix Specification Table 1 DS 2CC197P A Parameter Model DS 2CC197P A Image Sensor 1 3 inch SONY vertical double density interline CCD Signal System PAL Effective Pixels PAL 752 H x 582 V Min Color 0 1Lux F1 2 0 0003Lux F1 2 sensitivity x 256 Illumination B amp W 0 01Lux F1 2 0 00003Lux F1 2 sensitivity x 256 Electronic Shutter Speed 1 50s to 1 100 000s Lens Mount
8. the back focus ring 2 DD VD Optional Switch Auto Iris Video Drive The camera inputs the video signal level into lens interior and internal drive circuit outputs control voltage to adjust lens aperture through electronic motor Auto IRIS Direct Current Drive The camera interior adds lens aperture electronic motor s drive circuit and can directly output DC control voltage to control lens electronic motor 3 Menu Button Press the middle menu button to call out menu then press the up and down to move the items and left and right button to select items 4 Fixed Bracket Fastness Used for mounting bracket 1 3 2 Introduction of Box Camera Auto IRIS Port 540 Al Wise COLOR CAMERA I Video pe CETO NN 11 GND Driver Figure 1 2 Definition of Auto IRIS Port On the other side of the camera there is an interface for auto iris the type is negative pattern four square holes and the definition of pins is shown in the figure above The interface of video drive auto iris is using three pins i e Power Video GND the interface of direct drive auto iris is using four pins i e damp damp drive drive The description of box camera rear panel i 1 2 3 4 9 MEER VIDEO du E x ry POWER 24 4 is DC12V 7 Q 5 9 Fig 1 3 The rear panel of box camera 1 Alarm OUT IN GND support alarm in and out 2 D N The switch of D N mode via
9. x 256 When lens is ELC press enter to select shutter speed Auto Auto x 2 Auto x 4 Auto x 6 Auto x 8 Auto x 12 Auto x 16 Auto x 24 Auto x 32 Auto x 48 Auto x 64 Auto x 96 Auto x 128 Auto x 160 Auto x 256 Note Auto x 2 Auto x 4 and so on mean sense up function realized through adding exposure time 3 2 8 AGC Settings When selecting Day or Night mode AGC enables including HIGH MID LOW and OFF items while selecting Autol mode AGC disables When sense up enables AGC becomes MOTION which includes five modes SLOWER SLOW STD FAST FASTER The camera will automatic calculate to select sense up or AGC to promote brightness of image according to the speed of object 3 2 9 Synchronization Support internal and line lock synchronization When using DC12V power supply it displays internal synchronization and is not adjustable When using AC24V user can select internal or line lock synchronization 3 2 10 Language Move cursor to CN EN through up down and press left right to select CN or EN 20 3 2 11 Special Function Move cursor to Special Function press enter and the menu will appear on the screen Special Func ON DETECT OFF FLC OFF BLEMISH DETECT VIDEO 55 RS485 soc SYS INFO s55 RETURN n 4 Note has twinkled motion detection pane and can trigger alarm output Motion Detection MODE can only
10. 10 2 2 HARDWARE INSTALLATION cuore 12 CHAP TER c 13 MENU DESCRIPTION em 13 1 A ash ds Ra E ORE 15 3 2 MENUMDEMAILS ne ex e v hates aa 15 3 2 1 Camera ID Seti OSA air terrai 15 3 2 2 Tens Type Settings aaa ai 16 3 2 3 UBICA E 17 3 2 4 BEC Settings ito er eee aeneo aA Tn Fee a eu eeu den the Sa 17 3 2 5 Super WDR Settings e teer eae ere TAS aS aee ea TERRE Re Sh A 18 226 D oci t eee eee o ttes ee eee 18 3 2 7 Shutter Settings tae e e P ERE es 20 3 2 8 cAGCSettings iore A ese 3 2 9 Synchronization 3 2 10 1 3 2 11 Special Function 3 2 12 Exit Setting APPENDIX SPECIFICATION ccccccccccccscocccossceceseescecccccsvecescesceccscescecescescensveescueeteuscusevecsseseveeicuseseessvtes 27 ABLE DS 2 COOLS A A E ue ette eati rd rt AE E 27 TABLE 2 DS 2 C657 Y P in toe Ld cest aet ald vere elt tasers 28 Introduction 1 1 Product Features This camera adopts high performance CCD and advanced print circuit board design technology and possesses of high resolution low distortion low noise featur
11. 3Lux F1 2 sensitivity x 256 Electronic Shutter Speed 1 50s to 1 100 000s Lens 2 8 11mm 2 5 6mm optional Auto IRIS DC Day Night IR Cut Filter Auto Switch Horizontal Adjustment Range 0 355 Vertical Adjustment Range 0 90 Horizontal Resolution TVL 540 Color 600 B W Wide Dynamic Range 160X Synchronization Internal Power synchronization vided 1Vp p Composite Output 75Q BNC Test Monitor OUT 1Vp p Composite Output 75Q BNC Device Line S N Ratio More than 50dB Camera ID On Off 15 letters adjusted position Auto Gain Low Middle High Off D N Mode Auto Day Night Auto White Balance Auto trace AWB1 Auto trace AWB2 Manual Auto Privacy On Off Maximum 8 Zones Menu Motion Detection ON Off Flicker Proof On Off Language English Chinese Gamma Amendment Digital Zoom Digital Noise Reduction Video POS NEG Mirror Resolution Aperture Y C Blemish Detection Power Supply 24V AC 20V A 10 12VDC 300Ma 10 Working Temperature 10 C 60 C 14 F 140 F Power Consumption 4W 10W MAX With ICR Working Dimension 9110 99mm x 105 5mm 04 4 x 4 2 Weight 400g 0 881bs 28
12. Day Night High definition WDR ICR Color Camera USER S MANUAL Version 2 0 0 Thank you for purchasing our product If there is any question or request please do not hesitate to contact dealer This manual is applicable to DS 2CC197P A DS 2CC577P A color cameras This manual may contain several technically incorrect places or printing errors and the content is subject to change without notice The updates will be added into the new version of this manual We will readily improve or update the products or procedures described in the manual dd safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Serious injury or death may cause if any of the warnings is neglected Cautions Injury or equipment damage may cause if any of the cautions is neglected Warnings Follow these safeguards Cautions Follow these precautions to prevent serious injury or to prevent potential injury or death material damage Warnings 1 In the use of the product you must be strict compliance with the electrical safety regulations of the nation and region 2 Input voltage should meet both the SELV Safety Extra Low Voltage and the Limited Power Source with AC 24V or DC 12V according to the IEC60950 1 standard Please refer to technical specifications for detail informati
13. e 3 Default 12 x 8 windows on full screen pressing enter button can cancel a window MODE2 Setting Move cursor to MODE2 press enter and the menu will appear on the screen ALARM 2 ON gt OFF 2 OFF gt ON 5 RETURN Move cursor to ON gt OFF press left right to set the responding time from ON to OFF 0 2 5 10 15 20 25 30 unit s And press left right to set the responding time from OFF to ON After settings move the cursor to Return and press confirm button to return to the previous menu Note ON gt OFF means the alarm will be triggered when motion detection duration is longer than 2s OFF gt ON means the alarm will continue for 5s when motion detection stops ig h level Alarm In Hig Alarm Out off Fig 3 2 1 22 Interior amer Prep es Camera Circuit Alarm In Alarm Input Fig 3 2 2 Interior Circuit Alarm Output Fig 3 2 3 Note DS 2CC577P A motion detection settings are On and Off select On to enter motion detection interface as follow the operations are the same as ALARM 1 above ALARM TYPE 1 12275374 SENSIT 0 RETURN FLC Move cursor to flicker proof function and press enter to set on or off This function is used for PAL standard 23 camera under 60Hz light source and NTSC standard camera under 50Hz BLEMISH After used a long time Charge Coupled Device CCD will appear blemish and th
14. e area user can cover some place to protect other s privacy The number of privacy mask area is up to 8 Color B W auto switch The camera will display color image and become monochrome automatically at night AGC When object being shot look dim please turn on AGC It is propitious to enhance brightness To output standard video under different illumination the range of auto gain control must be large enough When under low illumination AGC will increase camera s sensitivity and output bright and clear video S N ratio It is the ratio of Signal voltage and noise voltage The ratio is larger the effect of noise is less and the image is more spotless OSD On Screen Display The camera supports friendly menu interface on the screen and it s convenient for user selecting expected function 3 axis adjustment Adopt advanced 3 axis mechanism design meet different mounting requirement by flexibly adjusting the lens into the required angle Synchronous System Synchronization usually contains power synchronization and internal synchronization Internal synchronization uses synchronous signal which is generated by camera s crystal oscillator to complete synchronous scan Power synchronization uses synchronous signal which is generated by camera s adaptor to complete synchronous scan White Balance Because the camera could not adjust the color temperature according to the light alteration as the eyes that will cau
15. es etc which extremely suitable for supervisory system and image process system Adopt high performance SONY CCD and supply high definition and clear image color 540TVL and B W 600TVL Low illumination Color 0 1Lux F1 2 B W 0 01Lux F1 2 Support ICR filter auto switch Support OSD menu controlling enable user to configure the detail parameters DS 2CC577P A support remote control Adopt advanced stepping motor and sleep mode to avoid ICR oscillation Support BLC with programmable BLC area Support auto white balance with high color rendition High SNR give rise to clear and pleased image Support auto electronic shutter control to adapt to different environments Support auto gain control adaptive brightness Support auto iris Support Privacy mask with 8 optional colors and 8 configurable areas Advanced design technology with high reliability Advanced 3 axis mechanism design meet different mounting requirement by flexibly adjusting the lens into the required angle Only Dome camera support Convenient back focus adjustment Adopt advanced double plate design to guarantee the CCD s heat dissipation and image s quality Support RS485 remote control Invalid for DS 2CC577P A 1 2 Chief Introduction about Function Motion Detection In the surveillance area the appearing motion object will trigger alarm User can select suitable sensitivity level with corresponding environment Privacy Mask In the surveillanc
16. is camera possess Blemish Detection Function to solve this problem Move cursor to BLEMISH press enter and the DETECT will become WAIT while this camera enables blemish detection function When WAIT becomes DETECT the auto modification is completed Note This function will be more active in the absolutely dark environment Make sure that close the lens s IRIS before using this function VIDEO Setting Video Setup i GAMMA 0 45 ZOOM DNR OFF POS NEG POS MIRROR OFF RES HIGH APERTURE 3 Y c Ce G RN d GAMMA Move cursor to GAMMA and press left right to set GAMMA value 0 45 or 1 Digital Zoom Move cursor to ZOOM press enter and the menu will appear on the screen Zoom Setup RATE 03 LOC RETURN The zoom rate is selectable from 01 to 16 Ater zoom selecting LOC press up down left right to control the image moving After setting press RETURN to back previous menu DNR User can set turn on or off the digital noise reduction POS NEG 24 Move cursor to POS NEG and press left right to select POS or NEG Selecting POS the video will be normal while selecting NEG the video will be negative MIRROR There are horizontal vertical middle and OFF in this function RESOLUTION Move cursor to RESOLUTION presss left right to select high middle or low to adjust video s resolution
17. m that if the power supply matches camera s before connecting to power supply the power supply that s commonly used is 12VDC or 24VAC Please refer to the specifications of the corresponding camera model for details 12 CHAPTE R3 Menu Description BLC SETUP BLC AREA AREA OK RETURN AREA SET VALUE 3 4 RETURN Camera ID qd SUE 1 ALARM 2 US IS AREA 1 2 3 4 ON gt 0FF OFF gt ON ABCDEFGHUKLM Se RETURN RETURN NOPQRSTUVWXYZ 0123456789 lt gt LOC SYS INFO RETURN SOFT HARD y DSP RETURN Specil Func DETECT OFF Privacy Mask Menu N FLC OFF ZONE 1 BLEMISH DETECT ON OFF CAM ID OFF VIDEO OFF LENS ALC PRIVACY ses SET OK WB ATW1 RS485 cae COLOR 7 BLC WDR WDR SYS INFO sies MOSAIC OFF D N AUTO1 RETURN ETURN SHUTTER OFF Jf AGC SE Video Setup SYNC INT GAMMA 0 45 LANGUAGE EN Manual WB ZOOM a SPECIAL DNR ZOOM EXIT SAVE tano INC a pica RATE 01 L RES HIGH LOC APERTURE 3 RELORI Y eos C Ao RETURN RS485 Setup ADDRESS 000 PROTOCOL PELCO RETUYN p D BAUDRATE 9600 WDR Setup RETURN VALUE1 3 VALUE2 3 CONTRAST LOW RETURN ELC Setup VALUE L H RETURN LL Setup AL C scup V PHASE 000 1 RETUYN VALUE RETURN eles 14 3 1 Menu Interface Press menu button for abo
18. o protection mode In this mode camera will keep Black White for at least 1 hour until the environment is bright enough Note 1 means auto switch from Day to Night And value from 0 to 7 means switching threshold the value is more the corresponding environment is darker And D gt N 3s means when the light condition is up to the switching threshold and 3s later the camera turns Day to Night And N gt D 3s is the same as D gt N 3s Auto2 Setting It is the same as the Auto except lack of VALUE Note Auto2 means external trigger switch There is D N port which is once grounding and will trigger switch from Day to Night Note DS 2CC577P A D N settings are Auto Day and Night The menu is as follow and the operations are the same as above AUTO D N VALUE 7 D gt N 3S N gt D 3S IR SET ON ETURN 19 3 2 7 Shutter Settings Move cursor to Shutter through pressing up down When lens is ALC press enter to select shutter speed OFF 1 120 1 250 1 500 1 750 1 1K 1 2K 1 4K 1 10K 1 100K Auto x 2 Auto x 4 Auto x 6 Auto x 8 Auto x 12 Auto x 16 Auto x 24 Auto x 32 Auto x 48 Auto x 64 Auto x 96 Auto x 128 Autox160 Auto x 256 When lens is ALC and WDR is on press enter to select shutter speed Auto Auto x 2 Auto x 4 Auto x 6 Auto x 8 Auto x 12 Auto x 16 Auto x 24 Auto x 32 Auto x 48 Auto x 64 Auto x 96 Auto x 128 Auto x 160 Auto
19. on 3 Do not connect several devices to one power adapter as adapter overload may cause over heat or fire hazard 4 Please make sure that the plug is firmly connected on the power socket 5 When the product is mounted on wall or ceiling the device shall be firmly fixed 6 If smoke odor or noise rise from the device turn off the power at once and unplug the power cable and then please contact the service center 7 If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the camera yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance Cautions Make sure the power supply voltage is correct before using the camera Do not drop the camera or subject it to physical shock Do not touch CCD Charge Coupled Device modules with fingers If cleaning is necessary use clean cloth with a bit of ethanol and wipe it gently If the camera will not be used for an extended period please turn on the lens cap to protect the CCD from dirt Do not aim the camera at the sun or extra bright places A blooming or smear may occur otherwise which is not a malfunction however and affecting the endurance of CCD at the same time The CCD may be burned out by a laser beam so when any laser equipment is on using make sure that the surface of CCD will not be exposed to the laser beam Do not place the camera in extremely hot cold
20. se color deviation White balance is the white rendition ability of the camera to adjust the problem according to the environment automatically ICR Auto Switch The filter will filter infrared light during the daytime and change to normal filter at night to ensure a high sensitivity and clear image BLC If there is glaring light in the background of the object being shot the object will look very dim In this situation turning on BLC function will make the object look bright and clear but the background scene will be overexposure BLC OFF BLC ON Super Wide Dynamic Range Super wide dynamic range function is intended to provide vivid images even under back light circumstances where intensity of illumination can vary excessively Super WDR allows camera to filter the intense back light surrounding a subject and thus enhances the ability to distinguish the features and shapes on the subject 1 3 Introduction of Box Camera Side Plate and Rear plate 1 3 1 Introduction of Box Camera Side Plate Figure 1 1 Box camera side plate 1 Back Focus Ring When confirm the lens mounting still don t focalize then need adjust the back focus ring Adjusting Method The back focus is adjusted on the optimal position but for compatible with different lens should adjust back focus ring The steps are as below firstly tighten the lens then loose the fixed back focus ring and rotate the lens till get clear image lastly lock
21. stallation the plane the outshoot must be less than 5mm When using the C assembly lens please adopt C to assemble the adapter 2 1 Mounting There are two mounting methods for camera box and dome wall mounting ceiling mounting which depends on the demand of the customers Please stick to the following steps take ceiling mounting for example wall mounting steps are the same 1 Select the mounting method and mount camera bracket according to the mounting method For cement wall first you need to mount expansion screw the mounting holes of it needs to be the same with bracket then mount the bracket shown as figure 2 1 For the woodiness wall then skip the first step and mount the bracket with self tapping screw Please note that the mounting wall needs to sustain the weight 3 times heavier than the sum weight of camera and bracket 2 Mounting the camera Screw the camera in the bracket by using the mount base at the top of camera Fig 2 1 Install the camera 3 Adjust the camera and move it to the monitoring point and screw down the knob in the bracket fix the 10 camera 4 Screw the lens into the head of the camera adjust the focus and fasten the lens Fig 2 2 Install the lens 11 2 2 Hardware Installation Note Take box camera for example Rear Panel Linkage of Box Camera VIDEO OUT 4 O POWER ALARM q Figure 2 3 Rear panel Linkage Note Please confir
22. the operating temperature shall be 10 C 4 60 C dusty or damp locations and do not expose it to high electromagnetism radiation To avoid heat accumulation good ventilation is required for operating environment Keep the camera away from liquid while on using While on a delivery the camera shall be packed in its original packing or packing of the same texture Regular part replacement a few parts e g electrolytic capacitor of the equipment shall be replaced regularly according to their average enduring time The average time varies because of differences between operating environment and using history so regular checking is recommended for all the users Please contact with your dealer for more details Table of Contents CHAP TER Lio A RARE 1 INTRODUCTION Bt 1 T TPRODUCT FEATURES i rene eoe erede in 2 1 2 CHIEF INTRODUCTION ABOUT nennen nennen 2 1 3 INTRODUCTION OF BOX CAMERA SIDE PLATE AND REAR PLATE ennt 4 1 3 1 Introduction of Box Camera Side 1 4 1 3 2 Introduction of Box Camera Auto IRIS Port iii 5 1 4 DOME CAMERA APPEARANCE A SIRS CONTROL cess c M CHAPTER Za 9 INSTALLATION AAA TO 9 2 1 MOUNTING RE a O YE MR
23. trigger alarm output without twinkled motion detection pane Move cursor to Motion Detection and press left right to select motion detection mode OFF MODEI or MODE2 MODE1 Setting Move cursor to MODEI press enter and the menu will appear on the screen ALARM 1 TYPE 1 AREA 1527374 SENSIT 0 RETURN Press up down to select Type 1 and move cursor to AREA and press left right to select from 4 areas move cursor to SENSIT and press left right to select sensitivity value from 0 to 7 After settings move the cursor to RETURN and press confirm button to return to the previous menu Press up down to select Type 2 the area setting is not available now Move cursor to SENSIT and press left right to select sensitivity value from 0 to 7 After settings move the cursor to RETURN and press confirm button to return to the previous menu 21 Press up down to select 3 and move cursor to AREA Press left right to select Default or SET If Default is selected press Enter to display the default areas and press Enter again to exit If SET is selected press Enter and up down right left to select areas and then press Enter on the selected area to choose or hide the area Move the cursor to RETURN and press confirm button to exit Note Type 1 Has 4 adjustable windows Type 2 Full screen Typ
24. ut 2s the OSD menu will show on the screen ERU CAM ID OFF LENS ALC WB ATW1 BLC WDR WDR D N AUTO1 SHUTTER OFF AGC SYNC INT LANGUAGE EN SPECIAL Press up down button to move up down cursor left right button to select the different options 3 2 Menu Details 3 2 1 Camera ID Settings Press up down to move cursor to Camera ID press left right to enable or disable this setting Off The camera ID will not display after exiting On The camera ID will display after exiting Select On and press confirm button to enter Camera ID menu Camera ID ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789 lt gt LOC RETURN d Press up down to move the cursor to characters numbers symbols and press confirm button to modify the camera ID move the cursor to lt CURSOR gt press left right to move it to the characters of camera ID that needs modifying press confirm button to change the characters of camera ID to the blank move the cursor to position setting and press confirm button to enter the camera ID position setting menu then press up down to change the position of 15 camera ID press confirm button to exit the camera ID position setting menu and return to the camera ID menu move the cursor to Back and press confirm button to return to the previous menu 3 2 2 Lens Type Settings Press up down to move the cursor to LENS
Download Pdf Manuals
Related Search