MVX Copy Keypad user manual sample
Contents
1. The contents of parameters in keypad block Please verify the same software exceed the setting range of the driver Please versions are being used If the same reset execute copy read and save again then execute the copy read and save functions again The numbers of parameters in keypad block Please verify the software versions are are more than the drive Copy save can t be ithe same Ifthe same then execute used at this time The copy function may Ithe copy read and save functions only be used when the parameter groups in jagain the keypad are less than or equal drive s There is not enough serial EEPROM space Please delete one block first and then execute read function Failed to delete serial EEPROM block Please check the communication wiring If communication continues to fail please contact the factory All of the serial EEPROM data blocks are Please execute copy read function SRuLE ntsnwtnctonaiond ite The serial EEPROM data blocks failed The Please re execute copy read function SAREC aant yamey ee seavad ne The parameters of the drive are locked and it 1 Please stop the drive will not execute the function of copy read Please set parameter 80 10 0 and then execute the copy read The drive will not allow a save function Please stop the drive Please set parameter 80 10 0 and then execute the copy save Err displays if the input is invalid Please stop drive Please set pa2. MVX Copy Keypad Instructions 1 Keypad AC Cutler Hammer RUN STOP JOG FWD REV EXT PU JOG DISPLAY LOCAL d E FWD E E O Me 2 Description of Keypad Left Arrow ZZ Right Arrow Enter parameter group mode Enter parameter mode from group mode In parameter edit mode exits mode backs up one step Cancels edited parameter exit from a parameter edit mode DISPLAY Display modes Display read mode save mode and delete mode Up and Down Arrows Move either up or down through the display pages Move either up or down through the group list Move either up or down through the parameter list Increase decrease the speed reference value on the keypad when selected Move either up or down through the copy blocks list in order to select the desired copy block Local JOG FWD REV Stop Reset This button has two integrated operations The button operates as Stop button for normal operation In fault mode it is used to reset the fault Stop Motor STOP from the keypad when keypad enabled In programming mode press STOP key to cancel previous action and back up one step Used for parameter edit confirmation acceptance confirmation of the edited parameter value with exit from parameter edit mode Press this button for 2 minutes to confirm to copy in copy mode save in save mode and delete in delete mode Reset Used for resetting a fault Fault history is re
3. eter selection Display the setting of the parameter End displays for approximately 1 second if input has been accepted After a parameter value has been set the new value is automatically stored in memory rESEt displays if the keypad reset driver Lod Pisplayeo when keypad is powered on 4 Keypad error message Illegal command code The command code The corrective action can be set with received in the command message is not the Transmission Fault Treatment available for the AC drive parameter 90 04 Illegal data address The data address received in the command message is not available for the AC drive Illegal data value The data value received in the command message is not available for the AC drive Slave device failure The AC drive is unable to perform the requested action Communication time out 1 CE10 will display when modifying communication parameters and auto re communicate after x seconds If communication continues to fail please check the wiring between the drive and keypad and avoid any magnetic interference The parameters in block are not suitable for Please delete the parameters in this model Please re execute copy read and copy delete mode read parameters save again from the same model and copy save again Failed to save data to the keypad EEPROM Please check all communication wiring If communication continues to fail please contact the factory
4. rameter 80 10 0 and then reset
5. set if ENTER is pressed while in the Fault History menu 3 Explanation of Display Message The AC drive input frequency reference 6 1808 Me setpoint percentage of AC drive The actual operation frequency at the output terminals T1 T2 and T3 The output current present at the output terminals T1 T2 and T3 The value of the user defined units uig The output voltage present at the output terminals T1 T2 and T3 20 0 Me temperature of the unit The AC drive forward run status The AC drive reverse run status Display the status of read block in copy read mode Press and hold the ENTER key for 2 seconds rEAd1 will flash and parameters are read from the drive and saved into the keypad under block1 or block2 block3 block4 depending which one is flashing maximum memory capacity is 4 programs Display the status of save block in copy save mode Press and hold the ENTER key for 2 seconds SAuE1 will flash and parameters from block1 or block2 block3 block4 depending on which one is flashing are downloaded into the drive Display the block you are about to delete Users may delete programs in the keypad by pressing and holding the ENTER key for 2 seconds dELE1 will flash and delete the parameters in block Parameter group selection The specific param
Download Pdf Manuals
Related Search