User Guide - Fritidstoa i Nacka AB
Contents
1. www fritidstoa se 3 TRANSPORT LOCKING DEVICE The toilet s combustion bowl is provided with a transport locking device because of its weight This transport locking device must be removed before the toilet can be used Instructions Remove the front panel Cut and remove the plastic strapping securing the combustion bowl to the toilet s steel frame INSTALLATION Correct installation of in out ventilation is essential for good combustion and for ensuring problem free use Placement Cinderella is approved for use in bathrooms but must never have water poured over it The toilet should stand on a hard level surface do not enclose the gap between the toilet and the floor Cinderella may be placed on a heated floor as it does not need to be bolted to the floor There are no restrictions on placement in relation to flammable materials and Cinderella can be placed in unheated rooms Ventilation IN The air supply to the toilet room should come from outdoors The air intake should have a dimension of at least 160 mm In order to minimise cold draughts the intake can be placed at floor level in the wall close to the toilet or in the floor under the toilet The necessary air will be sucked in through the base of the toilet It is important to ensure that the toilet s air requirements do not come into conflict with devices such as fireplaces or kitchen extractor fans For this reason the toilet room door should b2. combustion To increase the catalyst s useful life we recommend that you run one combustion cycle using only water once the toilet has been emptied about 5 times or at least once a year Instructions 1 Empty and clean the combustion bowl in the usual way 2 Pour one litre of water directly into the combustion bowl before re installing it 3 Start combustion without using a bag and or paper The water now boils away and the water vapour created cleans the catalyst 4 Once the combustion cycle is complete yellow light off the toilet can be used as normal once again Check at regular intervals to make sure that the hole for condensation water in the bottom of the T pipe has not become blocked Check the entire length of the exhaust pipe as well to make sure nothing is blocking the flow of air In connection with normal cleaning or if someone has forgotten to use a bag the bowl should be cleaned as follows Please note the toilet must be cold unused fan deactivated 1 Open the lid so the fan starts 2 Press START The flap down to the ash bowl will open and will stay open until the lid is closed Please note For safety reasons this may only be done if the toilet is cold unused 3 Clean using moist paper Clean the whole bowl carefully including the wings on the stainless flap Drop the paper into the combustion bowl 4 When you have finished cleaning close the lid www fritidstoa se 5 TROUBLESHOOTING Reset Ho
3. er pipe supplied to a suitable length Feed approximately 5 cm of the connection pipe into the back of the toilet and the same amount into the T pipe It is a good idea to mark 5 cm on the pipe before hand so you can be sure that the pipe is correctly attached to the toilet 3 Fit the rain cap Press the rain cap down as far as it will go Please note Do not fit any form of insect net over the end of the exhaust pipe 4 Put the toilet into position and connect to an earthed socket 220 230 V own 10 A fuse 5 Start Cinderella by pressing the ON OFF switch down by the electrical connection on the back of the toilet The manufacturer s warranty does not cover an incorrectly installed Cinderella Please contact your retailer or Fritidstoa ab for advice and helpful hints www ftritidstoa se 5 USE 1 Check that the green light on the control panel is on this indicates that 230V is connected and the mains switch is on 2 Lift up the lid and the seat The fan starts automatically 3 Place one Cinderella bag in the bowl A bag must be used every time the toilet is used 4 Lower the seat 5 Use the toilet If very little is produced or if a lot of paper is used pour a few decilitres of water into the bag to make sure that it will drop down properly 6 Close the lid 7 Press the start button you will hear an acknowledgement sound The bag and its contents will fall down into the combustion chamber 8 The ye
4. Cinderella ELECTRIC COMBUSTION TOILET User Guide Fritidstoa ab f rbr nningstoaletter REA Contents CONTENTS OFTHESCARTON cu a ee 3 CONSTRUCTIONS a E ace sen ere eee eee eae 3 SS Ales LN ce ene tees Se ES oe re SE nae ee en ee er 3 TRANSPORT LOCKING DEVICE 4 VIN SAE INA DT na nese erence cee ree less ses 4 USE aces eae eee SON cee anlar Sn a eae coe Ae ssh slak 6 EN cal TR Uf TSE eee TSE ER eee ere AE EE 7 MAINTENANCE T ee or ra eran RAS RA ssk dee sees 7 TROUBLESHOOTING eee ena arenes 8 TECHNICAESPECIFICATIO NS m a ee 9 MYROR TR IN lb Yom acre EEE sera ree a te erie rere t sen ade Seeda 9 ao Ge eee E eee eee eee ee 9 The back page of the User Guide is an instruction sheet that you can cut out and display in the toilet room VERSION 2 0 English CONTENTS OF THE CARTON The Cinderella Classic delivery includes a e 1 Cinderella Classic e 1 carton 500 bags e 1 connection pipe 110 mm x 430 mm e 1 T pipe 90 110 mm e 1 Rain Cap e 1 User Guide PTF noaa D Geos 11 20084 CONSTRUCTION Cinderella is manufactured on the inside in acid resistant steel and the bowl is manufactured in glass fibre reinforced plastic The heat source is a specially manufactured heating coil designed to withstand high temperatures and loads The temperature is regulated by electronically controlled sensors The intelligent SENSE combustion system detects when the combusti
5. e be kept closed and should be airtight There should be no extractor fan in the toilet room for the same reason Cinderella will extract any damp air in the toilet room www fritidstoa se English Ventilation Out The inbuilt fan keeps the toilet cool and presses out humid air from combustion through a catalyst Venting is achieved partly by means of the fan and partly through natural pressure known as the chimney effect The exhaust pipe s total length must not exceed 3 5 metres The exhaust pipe should extend 60 centimetres above the roof at its exit point in order to obtain the best possible pressure If bends are needed to pass windows or eaves for instance up to 4 x 30 angles or no more than 2 x 45 angles may be used It is important that the dimension of the pipe is 110 mm all the way between the toilet and the rain cap The pipe should have a smooth inner surface and preferably be PP model standard exhaust pipe for internal installation Flexible tubing and pipes of smaller dimension do not work If a longer pipe or more bends are required it is possible to install a more powerful fan in the toilet Please contact your retailer or Fritidstoa ab 1 Create a hole for ventilation either out through the wall easiest or up through the roof Use a 111 mm piercing tool 2 Assemble the necessary pipe parts It is a good idea to use a little om detergent to make them easier to fit together Trim the connection
6. his warranty is valid in the Nordic countries In other countries the warranty is valid for one 1 year Costs related to service after the warranty period or faults caused as described above must be met in full by the customer Any repairs must be made by authorised staff In the event of any complaint please quote the serial number you will find on the back of the toilet The toilet must be cleaned for service and repairs SERVICE When service is required during or after the warranty period please contact an authorised retailer or Fritidstoa ab You will find a list of authorised retailers at http www fritidstoa se You are always welcome to contact Fritidstoa ab on 46 0 8 615 25 25 or info fritidstoa se if you have any questions about your Cinderella www fritidstoa se gt Fritidstoa Forbranningstoaletter Fritidstoa ab Box 202 16 SE 161 02 Bromma 46 0 8 615 25 25 info fritidstoa se www fritidstoa se Please read this before using the toilet 1 e Lift the lid and seat 2 Place one Cinderella bag in The fan will be activated the bowl A bag must be used every time the toilet is used 4 Use the toilet If very little is 5 Close the lid 6 Press START produced pour a few decilitres of water into the bag to make sure that it will drop down properly Cinderella can be used in the normal way even while combustion is in progress n ae f rbr nningstoaletter
7. ld down the START button for 5 seconds to reset the toilet ERROR RED YELLOW GREEN AUDIO SIGNAL ACTION Loss of line voltage Off 3 beeps gt W N Check that power cable is connected Check that power is switched on Check that there is voltage in the socket Open and close the lid Start combustion Fan error Flashing Flashing 10 beeps Reset the toilet hold down the START button for 5 seconds Open and close the lid Start combustion Repeated errors switch off all power and contact your service centre Flap will not open bag does not fall down Flashing 10 beeps If the toilet is hot Press START several times without putting in a bag If this does not help put in a new bag containing 3 5 dl water and press START If this does not help wait until the toilet cools the fan stops If the toilet is cold Open the toilet lid and press START The flap will open and any paper residue can be removed If the flap does not open and the motor makes a humming noise for a few seconds remove the ash bowl and knock from the underside of the combustion lid at the top of the combustion chamber to release it The cover should have a gap of about 1 mm Ash bowl in wrong position Flashing Flashing 3 beeps Fit ash bowl Pull ash bowl handle firmly to the left It might be a bit stiff if the toilet is new Interruption in heating circuit Flashing Cont bee
8. let is cool The fan should not be running 2 Remove the lower front panel by pressing out the button and then pulling the panel straight towards you 3 Turn the combustion bowl so that the handle points straight forwards Red and yellow lights will now indicate that the combustion bowl is out of position 4 Pull out the combustion bowl towards you 5 Lift out the inner bowl and empty the ash in a suitable place The ash is completely free from bacteria and can be used as fertiliser on flower beds 6 Clean any urine crystals or burnt residue from the inner bowl Please refer to the Maintenance section Make sure that both the inner and outer bowls are dry and clean 7 Replace the inner bowl and push in the entire combustion bowl until it is in place 8 Turn the handle firmly to the left as far as it will go the red and yellow lights will go out 9 Replace the front panel MAINTENANCE The toilet can be cleaned using ordinary detergents both in the bowl and on the outside Never use large amounts of water Use a spray bottle or a moist cloth sponge When urine is incinerated urine crystals are formed These are often found around the edges and look like dried cement To remove them and any burnt residue remove the inner bowl fill it with hot water and leave it to stand for 20 30 minutes Brush out the inner bowl leave it to dry and then replace everything in the toilet A clean ash bowl ensures more efficient
9. llow light on the control panel indicates that combustion is in progress The fan remains active throughout the combustion process When the yellow light goes out combustion is complete the fan will continue to run until the temperature in the combustion bowl is down to around 85 9 Depending on the amount of waste combustion time will vary from 30 to 110 minutes General remarks about use The toilet may be used while combustion is in progress New combustion is started after every visit by pressing the START button The toilet detects when combustion is complete The toilet lid must be kept closed when the toilet is not in use Combustion will not start while the toilet lid is up Before you leave make sure that the bag and Its contents have been flushed away properly NEVER put in a new bag for the next user when you are finished Just leave it on the lid When combustion is complete the yellow light on the control panel will go out The fan will deactivate when the temperature in the combustion chamber is down to 85 If the toilet is not to be used for some time disconnect the power cable to protect against lightning strikes Flammable liquid or material must never be placed in the toilet and or flushed down www fritidstoa se English EMPTYING When Cinderella has been in use for some time it is time to empty the ash Instructions 1 Make sure that combustion is not in progress and the toi
10. on process is about to end and is able to optimise combustion time and energy consumption Cinderella s inbuilt fan keeps the toilet cool during combustion and adds oxygen to the combustion process All of the toilet s components are of the highest quality Each toilet undergoes comprehensive testing before delivery Cinderella is tested and approved by SEMKO Cinderella is also EMC tested in accordance with current EU standards and is CE labelled SAFETY e Combustion is NOT active when the toilet lid is open e When the toilet is warm it is NOT possible to activate the flap motor when the lid is open The lid must be closed before it is possible to flush e The flap CANNOT be set in the open position e g for cleaning as long as the toilet is warm This can only be done when the toilet has cooled down the fan has stopped e If the temperature within the shell is too high a fuse will be triggered and combustion will come to a halt The fuse must be reset manually before the toilet can be used again Please refer to the Troubleshooting section e The toilet s shell is manufactured in a fire resistant material e Combustion will not start will be halted if the combustion bowl is not in its correct position e The toilet s fan is activated until the temperature in the combustion bowl has cooled to 85 C In the event of a power cut the fan will continue to operate on battery power e NEVER pour flammable liquids into the toilet
11. ping Switch off mains power Wait until the toilet is cool fan has stopped Check temperature monitor on the side of the toilet Unscrew the grey plug Press the fuse with your finger until you hear a click Never use sharp objects If the fuse has been triggered check the airflow in and out If it has not been triggered please contact your service centre Lid open Flashing Close toilet lid Red light stops flashing Temperature sensor fault Flashing Flashing Cont beeping Reset the toilet hold down the START button for 5 seconds Open and close the lid Start combustion Repeated errors switch off all power and contact your service centre www fritidstoa se English TECHNICAL SPECIFICATIONS Seat height 540 mm Total height 600 mm Width 390 mm Depth 590 mm Weight 34 kg Ventilation dimension 2 110mm Voltage 220 240 VAC 10A Fan capacity 5 3 W 49 db 184 m hour Combustion output 2 kW Energy consumption 1 0 2 0 kWh toilet visit WARRANTY The warranty is valid for two 2 years from the date of purchase The warranty covers manufacturing faults and faults in components that occur during the warranty period Fritidstoa ab will cover the costs of spare parts labour and transport between Fritidstoa and your nearest retailer during the warranty period The warranty does not cover e incorrect installation e incorrect utilisation e transport e lightning strikes T
Download Pdf Manuals
Related Search