Operating instructions DALI EASY RMC
Contents
1. The fade time is the time in which the lighting system changes from one lighting scene to the next in sequencer mode Cycle time The cycle time is the time in which the daylight simulation system runs through a complete daylight cycle OSRAM Operating Instructions remote control DALI EASY RMC page 3 General Function The remote control sends digital coded Infra red signals to the IR receiver type DALI EASY IR The receiver converts the Infra red into corresponding telegrams and transmits them to the connected DALI EASY control units Detailed view of the remote control OSRAM transmitter m Cr Scene 1 Chi TS Scene 2 ce ors Seene 3 Ch3 Ch4 E Start Time y9 ot On Off ON DIP Stop Time 2 Dimming E 1234 DIP Switches Application The infra red receiver can be mounted in a luminaire a ceiling panel or with an appropriate cover in a cavity socket Make sure that the remote control can point at the infra red sensor at an angle as steep as possible Bear in mind that the maximum range of the remote control is around 10 15 metres Note Make sure that there is a line of sight between the IR receiver and the remote control Up to four IR receivers may be connected To ensure that the remote control function operates properly the IR receiver must not be exposed to direct light Wherever possible mount the IR receiver in a shaded spot nade 42. no interference between them This is how you process a RESET resp change the infra red codes 1 Set the infra red code you want on DIP switch 1 e DIP switch 1 to OFF IR code 1 e DIP switch 1 to ON IR code 2 2 Note the settings of DIP switches 3 and 4 set DIP switches 3 and 4 to ON 4 Press any button on the remote control the remote control must be pointing at the IR sensor L 3 then appears on the remote control display The luminaires provide confirmation of the setting e For IR code 1 the luminaires flash once e For IR code 2 the luminaires flash twice 5 Set DIP switches 3 and 4 to their original positions The functions of the DIP switches are given in the table above OO Notes on RESET and changing the IR code In the event of a RESET or change of IR code all the connected control units are reset or changed You should therefore disable the connection to the IR receiver for the control units that are not to be reset or changed or disconnect the power supply for these units If there is more than one system in the reception area their IR receivers must first be disconnected or adequately covered to avoid an unwanted RESET OSRAM Oneratina Instriictions remote control DAI FASY RMC nade 7 Appendix Technical data Designation DALI EASY RMC Batteries required 2pc Micro AAA LROS Alkaline type IR Signal disturbance immune 38 KHz Rmap protocol digital coded 2 OSRAM specific codings selecta
3. the display is active This time is lengthened or shortened with the Start time and Stop time buttons The new fade time is activated when the sequence is next Started Scene 1 Scene 4 These buttons are used to store the individual scenes and call them up 1 Lu Short press The selected scene E appears on the display The scene is called up 1 Lt i Long press The selected scene f 7 appears on the display after three seconds The scene is stored The luminaires will flash once to confirm that the scene has been stored On Off Dimming This button is used to switch all the luminaires on and off and to change their brightness Short press All the luminaires are switched on or off Long press All the luminaires are faded up or down The fade direction changes each time the button is held down If the luminaires are switched off a long press switches them on and fades them from minimum to maximum brightness OSRAM Oneratina Instriictions remote control DAI FASY RMC nade A Operation Remote control display Display in response to buttons Display Meaning Description O 0 The sequence or daylight simulation is started HO hod The sequence or dayight simulation sputonhd LH scene 14 Scones 110 4areoaledup F i of daylight Scenes 1 to 4 of the daylight simulation are called up scene 1 4 sequence CE a sequence pe A command via Ch1 4 or On Off Dimming is t
4. OSRAM Oneratina Instriictions remote control DAI I FASY RMC Operation Description of the button functions Ch1 Ch4 Buttons Ch1 to Ch4 switch the luminaires in a group on and off and fade them up and down Short press The luminaires in the selected group are switched on or off Long press The luminaires in the selected group are faded up or down The fade direction changes each time the button is held down If the group is switched off a long press switches it on and fades it from minimum to maximum brightness Start time This button starts the sequence or lengthens the fade time LE Ie Short press appears on the display The stored lighting scenes are called up cyclically starting with Scene 1 If a scenes was called up before the sequence started the sequence will start with the fade to the next scene Long press The fade time is shown on the display for three seconds The fade time can be changed while the display is active This time is lengthened or shortened with the Start time and Stop time buttons The new fade time is activated when the sequence is next started Stop time This button stops the sequence or shortens the fade time Short press HU appears on the display The sequence is stopped The sequence can be resumed with the Start time button Long press The fade time is shown on the display for three seconds The fade time can be changed while
5. OSRAM en Operating instructions Il 2004 OSRAM DALI EASY RMC Version 1 0 OSRAM GmbH www osram com Costumer Service Center CSC www osram de Steinerne Furt 6286167 Augsburg Germany Tel 49 1803 677 200 charges apply Fax 49 1803 677 202 General Contents General Safety information 2 Definition of terms 3 Function 4 Application 4 Operation Description of the button functions 5 Remote control display 6 Remote control settings 7 Appendix Technical data 8 Safety information The following information is provided for your safety e Please read these operating instructions carefully before installing and using the DALI EASY RMC remote control This is the only way to ensure that you use the equipment safely and correctly Keep these operating instructions in a safe place for future reference You should make sure that everyone who uses the DALI EASY RMC has read these operating instructions e The relevant safety and accident prevention regulations must be observed page 2 OSRAM Operating Instructions remote control DALI EASY RMC General Definition of terms Sequence A sequence is taken to be the automatic retrieval of stored lighting scenes and their cyclic playback Group luminaire group A group is a collection of luminaires connected to the same DALI output channel This means that all the luminaires in a group always have the same brightness IR receiver The infra red rece
6. ble Distance approx 10 15m follow mounting instructions of the IR receiver Operating temperature OC 40 Protection type IP20 Dimensions 120 x 57 x 26 mm LxBxH The CE symbol signifies compliance with the relevant EU Directives nade 8 OSRAM Oneratina Instructions remote control DAI I FASY RMC
7. iver receives the signals from the remote control and forwards them to the DALI EASY controller Short press A short press means pressing a pushbutton for less than one second A short press is used for example for switching luminaires on and off Long press A long press means pressing a pushbutton for more than one second A long press is used for example for dimming the luminaires Light switch Light switches are used to switch luminaires on and off in a room and to fade them up and down They are connected to the external switch input on the DALI EASY controller Scene lighting scene A lighting scene defines the lighting situation in a room This presupposes that there are a number of luminaires or luminaire groups in a room and that their brightness can be adjusted independently of one another Example 1 Office lighting Offices often have rows of luminaires running in parallel to the window Lighting scene A The luminaires near the window are set to minimal brightness The in daylight luminaires furthest away from the window are set to maximum brightness Lighting scene B All the luminaires are set to the same brightness after dusk Example 2 Coloured effect lighting The luminaires or luminaire groups have different colours red green blue white They are set to different brightness levels according to the shade of colour required for the room lighting This mixing colour is a lighting scene Fade time
8. ransferred DE The function is not available in the current operating mode Display for the fade time of a sequence 0 1 to 0 9 seconds be 1 to 59 seconds Long Time Da 1 to 99 minutes Display for the cycle time in daylight simulation Description Display Daylight simulation 1 to 24 hours nade 6 OSRAM Oneratina Instriictions remote control DAI FASY RMC Operation Remote control settings The following settings can be made using the DIP switches in the battery compartment of the remote control DIP switch Function S aL L Te L JEL Tel ON ls Daylight simulation is disabled ON LJ Daylight simulation is enabled 4 _ M Learn mode for transferring the IR code to DALI EASY and resetting DALI EASY to the factory defaults RESET Disabling scene storage Storing of scenes can be disabled by means of DIP switch 2 The ensures that scenes cannot be changed by mistake The DIP switch positions are shown in the table Changing between sequencer mode and daylight simulation Sequencer mode and daylight simulation mode are activated using DIP switches 3 and 4 Both operating modes may also be deactivated DALI EASY then operates in lighting control mode The necessary DIP switch positions are shown in the table RESET or setting the IR code The two IR codes enable two separate DALI EASY lighting control systems to be operated in the same room each with its own remote control with
Download Pdf Manuals
Related Search