OPERATING INSTRUCTIONS Filter system
Contents
1. Filter Systems FILTRONIC Hissgatan 2 Box 2284 SE 531 02 LIDKOPING Tel 46 510 208 10 Fax 46 510 201 40 e mail office filtronic se www filtronic se Version 1 OPERATING INSTRUCTIONS Filter Systems MG400 Filter system D FILTER SYSTEM en jala FOR A BETTER WORKBENCH ENVIRONMENT Table of contents 1 Introduction 2 2 Content 2 3 3 Safety instruction 4 4 Put into operation 4 5 Troubleshooting 5 6 Maintenance and service 6 8 7 Technical data 9 8 Article number 10 9 Warranty 11 1 Introduction MG400 is a mobile filter unit for elimination of particles and gases in polluted process air from soldering gluing cleaning laser printing processes etc 2 Content Inlet pipe O 160 mm Lid Lock Pre filter box Main filter 4 pcs Outlet pipe O 125 mm Control panel 0 NOW BB WN FH Power intake with fuse Lah AN r r oe PI 5 kA mae NA TAN PA TU ey ee AE Jia ni pet ai Oe 10 Warranty General conditions according to ORGALIME S 2000 Filtronic guarantees the product for manufacturing failures for a time period of two 2 years on filter units and accessories consumptions not enclosed The time is measured from date of invoice Only use genuine Filtronic consumables and spare parts in order to ensure reliable function and to maintain the unit s warranty Repairs must be performed by personnel trained by Filtronic The information gi2. a new main filter is mounted the filter monitoring needs to be set to zero This can be done in two different ways Via the control panel 1 2 Switch off the circuit breaker 15 Switch on the circuit breaker 15 at the same time as the buttons 9 and 13 are pressed down A ready signal sounds and the LED indicators die down Via the remote control 1 Switch off the circuit breaker on the filter unit 15 Switch on the circuit breaker on the filter unit 15 at the same time as the push buttons 18 and 19 are pressed down A ready signal sounds and the LED indicators die down 5 Troubleshooting Do not modify the filter unit Repairs must be performed by personnel trained by Filtronic If the filter unit is out of order please check the electricity supply is connected in a correct way the fuse 6 3 AT is whole 1f yellow indicator 11 flashes Recommended filter lifetime of main filter is exceeded See Exchange of main filter under headline 6 Maintenance and service If red indicator 10 shines and alarm is heard Inferior suction capacity Switch off the filter unit Check that pre filter extraction arm or nozzle not are covered Clean extraction arm and nozzle if necessary Change pre filter if necessary See Exchange of pre filter under headline 6 Maintenance and service If the alarm remains change the main filter See Exc
3. thar OO Mer an hjang ed Gon DOP tested and hes a tepersticn The gas Miter is tested and hai TIN for work in wc ronie prod Dasar ba filter G oa ere EAT EL waa f Filter garanti F Itronic produk Don Hitergw arki hrebir ett varje r ot bi 5 FILTERSYSTEM MG75 Huvudfilter Ast re 750 2000 ESD titer Sr DOP kata b APN Cartttret Gr tertet biure En SIN Re mbete eet vor
4. hange of main filter under headline 6 Maintenance and service If the alarm not is taken care of the filter unit will stop within five minutes to protect against overheating The main filter should be changed at least once a year to guarantee the separation degree on gases At inspection repair appr seven pre filters are used before changing main filter 6 Maintenance and service Exchange of pre filter 1 Switch off the circuit breaker 15 2 Unlock the lid and remove it 2 J Remove the pre filter carefully 20 4 Mount the new pre filter S Replace and lock the lid 2 Exchange of main filter For optimal filter lifetime and filter economy always change pre filter when changing main filter i Switch off the circuit breaker 15 2 Unlock the lid and remove it 2 J Remove the pre filter carefully 20 4 Loosen the wheel 21 and lift up the pre filter box 4 5 NOTE The new filter has to be marked with the date of change 11 6 Exchange the four main filters 5 7 Replace the pre filter box 4 and mount the wheel 21 8 Mount the new pre filter 9 Replace and lock the lid 2 10 Set the filter monitoring to zero see instruction at page 8 Filter Systems FILTER UHIT MG7S Nain filter Artno 790 2000 6580 Filter waranty Tho iter warranty wears Dat every main fiter microtiter it degree Letter than 95 975 ooh har an arji ad bitre a seperetion degree better
5. ilter lt 38 C Relative humidity lt 60 Gas molecules gt 30g mol filtration is better with larger molecules Boiling temperature of gas molecules 50 C NOTE The unit may dust some from the main filter after transportation Make sure the starting of the unit is made in an appropriate room Connect the suction hose or suction tube at the inlet pipe 1 Connect the power cord Connect the remote control 14 Switch on the filter unit 15 and thereafter the remote control on push button 16 When delivered the filter monitoring is programmed for normal load of the filter step 3 If you want to change the program press the button for filter monitoring 17 Step Indication Hours Application example EM 1 500 Heavy smoke formation gluing 2 1000 _ 3 1500 Inspection repair set by delivery saa 4 2000 paaa 5 2500 Papa 6 3000 7 Technical data MG400 Width x height x depth Weight Sound level at 1 meter Voltage Effect Glass tube fuse Maximum suction capacity Blower capacity Micro filter Separation degree MPPS Gas filter Separation degree Filter monitoring system Warranty excl filter CE guidelines RoHS 796 x 1016 x 402 mm 31 3 x 40x 15 9 inch 68 kg 150 Ib lt 55 dB A 115 or 230 Volt 300 Watt 2 x 6 3AT 250V 400 nv9 h 235 CFM 450 nv h 264 CFM gt 99 95 Yo gt 95 Yo Yes 2 years 89 336 2004 108 2006 95 Yes When
6. ven is not binding and does not free the user from his or her responsibility to check the equipment before using it Filtronic reserves the right to introduce technical changes in the course of product development Always contact the supplier before return a product The invoice has to be shown at the time of the complaint 8 Article number Filter system MG400 Micro Gas filter Standard 4 pcs Micro Gas filter Cleanroom 4 pcs Micro Gas filter MEK 4 pcs Micro Gas filter Ammonia 4 pcs Micro Gas filter Solvents VOC 4 pcs Pre filter 2 pcs Remote control with cable Remote control battery IR 450 1000 ESD 450 2000 ESD 450 2002 ESD 450 2003 ESD 450 2006 ESD 450 2012 ESD 450 4000 700 3057 L 700 3058 Control panel 9 10 11 12 13 14 15 Push button decrease LED indicator low airflow LED indicator filter time exceeded LED indicator operation Push button increase Intake for remote control Circuit breaker Remote control 16 17 18 19 Push button start stop Push button filter monitoring Push button decrease Push button increase 3 Safety instruction The unit must not be exposed to temperatures exceedi ng 50 C open flames or condensated sol vents Switch off the filter unit when changing filter 4 Put into operation The best possible gas filtration will be achieved if Process air temperature in the gas f
Download Pdf Manuals
Related Search