WITH EYE USER MANUAL
Contents
1. WITH EYE USER MANUAL WITH EYE TABLE OF CONTENTS IMPORTANT SAFETY GUIDELINES OPERATION GUIDE START UP COMPRESSED AIR TANK WARNINGS INSTALLING COMPRESSED AIR TANK PROPER USE OF BARREL BLOCKING DEVICE BATTERY INSTALLATION BATTERY CHARGING ELECTRONICS amp SETTINGS TRIGGER ADJUSTMENT VELOCITY ADJUSTMENT C A ON OFF ADAPTER REGULATOR ADJUSTMENT DISASSEMBLE REASSEMBLE AND CLEANING OF REAR INTERNALS PAINTBALL JAM ANTI CHOP EYES CHANGING BALL STOPPER CUP SEAL REMOVAL REGULATOR MAINTENANCE SCHEMATIC MISC TROUBLESHOOTING AIR LEAKS WARRANTY STATEMENT RSX PARTS LIST RSX SCHEMATIC N N u UU EF W mur 1 oo IMPORTANT SAFETY GUIDELINES A WARNING This paintball marker is NOT a toy It can cause serious injury or death Kingman recommends that the customer be at least 18 years of age to purchase this product Read this manual and air tank warnings before using this product Any modifications or tampering of original factory parts will void all warranties and liabilities from Kingman Kingman recommends using a barrel blocking device when the marker is not in operation To ensure proper adjustment of velocity fps Kingman strongly recommends using a chronograph for paintball use located at most paintball stores and paintball fields Before after use of the marker make sure to fasten all screws Screws may become loose due to vibration Loose screws can be dangerous and cause injur2. ORGO18 Barros HSEOO8 REGOOL 16 Distributed by Kingman Group 1 888 Kingman www kingman com 14010 Live Oak Ave Baldwin Park California 91706 USA
3. SCROO7 SCROO8 SCRO10 SCROLL SCROe5 SCROe6 SEROO1 SPROO1 SPROO2 SPROOS SPRO10 STBOOl STFOO1 STKOO1 STPO21 TRFOO2 TRSOOS VBTOO1 VBTOO2 VBTOO3 VBTOOU VRTOOl VTAO21 WRHOO2 WRHOOUW WRHOO6 Reg Rubber Grip Sear Roll Pin Trigger Touch Switch Roll Pin Trigger Roll Pin Trigger Frame Screw A MU x 8 Screw w washer A Circuit Board Screw Eye Panel Screw A Trigger Screw S Trigger Screw L Valve Body Screw A Vertical Screw A Dove Tail Lock Screw A Coil Set Screw Reg Screw MY x 4 45A Reg Adjuster Lock Screw 29B Sear Striker Spring Valve Spring ESP Sear Spring ESP Trigger Spring Striker Bolt mini Striker Buffer Top Cocking Knob Striker Plug matte silver Trigger Frame Saber Trigger matte black Delrin Bolt w Locking Knob Delrin Bolt Locking Screw Delrin Bolt Locking Bearing Delrin Bolt Locking Spring Vertical Adapter w Gauge Velocity Adjuster amp Spring Guide m silver Battery Harness Touch Switch 3P Eye Wire Harness longer wire Item Not Pictured RSX SCHEMATICS STPO21 STFOOL varas ORGOOB VBTOOU i VTAO21 VBTOO3 STKOOL i SPROO1 VBTOOT STBOOL ORGOOL BLSO21 SCROOL FNDOO2 FNDOOL _ ITPOO2 TRFOO2 eee ITPOOY y ITPOO3 ORG003 CD ka A SPROO2 __ ORGOO2 BARO10 GAGOO2 O C ORG005 ORG003 2 So ORGOO2 LPCO21 BARO21 d Y UL usroo9 VRTOOL ASAO13
4. e Cylinders heated to an excess of 250 F 121 C must be condemned or requalified in accordance with test defined in CFR 49 e The valve should NEVER be detached from the canister Please seek immediate assistance from a trained airsmith should this occur e Any tank packed with the product is intended for paintball use only e Confirm that there is an attached urethane O ring on the Compressed Air tank valve before attaching the tank to the marker The tank will leak air as soon as it is secured to the marker if the O ring is missing from the valve e A urethane O ring is highly recommended before attaching any air supply to the marker e NEVER over pressurize a Compressed Air cylinder e Avoid any direct skin exposure to the escaping gas when installing or removing any air supply e Never expose cylinders to corrosive materials or clean with any caustic cleaners INSTALLING A COMPRESSED AIR TANK Firmly screw the Compressed Air Tank clockwise into the markers C A On Off adapter ASAO20 HELPFUL TIP Before installing a Compressed Air Tank make sure that the tank is full and that it has a urethane bottle on the top of the valve to prevent air leaks IMPORTANT You should never need to use any hand tool to attach a Compressed Air Tank to the C A On Off adapter REMOVING THE COMPRESSED AIR TANK Firmly unscrew the Compressed Air Tank by turning the tank counter clockwise until it comes out of the C A On Off adapter HELPFUL TIP After f
5. ASAO18 ASAO20 BARO10 BARO21 BLSO21 BLS002 31202 ELMOOl FNDOO1 FNDOO2 FNDO21 GAGOO2 GRPOOl GRPOOe HSEOO8 HSFOOW HSFOO9 ITPOO1 ITPOO2 ITPOO3 ITPOOL JE1015 JE1029 LPCO21 ORGOO1 ORGOO2 ORGOO3 ORGOOS ORGOOS6 ORGOOS ORGO16 ORGO17 ORGO18 ORGO21 ORGO22 PAKOOl RECO21 REGOO1 REGOO2 REGOO3 REGOOYW REGOOS REGOO6 C A On Off Depressing Pin C A On Off Retaining Screw f C A On Off Adapter Knob matte black C A On Off 1 8 Hose Plug C A On Off Adapter matte black 12 2PCS Barrel 12 Barrel Tip matte silver Eye Panel Set matte silver Ball Stopper Tadao Circuit Board Coil Set Coil Pin Capacitor Touch Switch Membrane Feed Neck Twist Clamp C Clip Insert Twist Clamp C matt silver 600 psi Gauge Wrap Around Grip black LED Lens Disconnect Hose female x female Plastic Washer 90d Male to Male Adapter STD x MET Cup Seal Valve Pin Valve Body Valve Body Buffer 9 6v Rechargeable Battery A C Charger w LED Low Pressure Chamber matte silver Striker O ring O ring 015 80D Barrel O ring Vertical O ring Inner Valve Body O ring 010 O ring Valve Pin O ring L Valve Pin O ring S Inner Reg O ring 4008 70 Reg Piston O ring 014 70 Reg Adjuster O ring Spare Parts Kit RSX Receiver Regulator complete Reg Top Body Reg Piston Reg Spring Reg Mid Body Reg Adjuster REGOO7 RPNOO1 RPNOOe RPNOOU SCROOl SCROOe2 SCROO3 SCROOU SCROOS SCROO6
6. ready to fire Blinking Green No ball in breach Blinking Yellow Eye malfunction Remove loader and check breach Solid Purple Firing Mode Menu Solid Teal Blue Trigger Debounce Menu PROGRAMMING Programming Mode can only be initiated while the Tournament Lock is disabled Pressing the push button switch to the right of the microcontroller on the Circuit Board will toggle the Tournament Lock After every press of the Tournament Lock button while the marker is off the light will Flash Green or Red to indicate the status of the Tournament Lock Green means the Tournament Lock is disengaged thus allowing the user to enter the Programming Mode Red indicates the Tournament Lock is engaged and programming can not be initiated TO ENTER FIRING MODE PROGRAMMING MENU While the marker is off press and hold the Mode Button then press the Power Button and the LED will cycle through multiple colors until the LED displays Solid Purple for the Firing Mode Setting Menu TO CHANGE THE FIRING MODE Press and hold the Mode Button until the Solid Purple LED goes out The LED will blink to show the current Firing Mode setting For example if the current Firing Mode setting is on PSP Ramp the LED will blink 3 times Once the LED stops blinking you will have two 2 seconds to enter a new mode setting To enter a new Firing Mode setting press the Mode Button to select the new Firing Mode setting For example for Semi auto Uncapped Mode you must press the Mode B
7. 3 ST KOO o STPO21 VBTOO1l STFOOL A ES KORGOOL lt SPROO1 i EE VTAO21 Ny DISASSEMBLE REAR INTERNALS STEP 1 Lift upward on the Top Cocking Knob to allow the Delrin Bolt to slide out from the rear of the Receiver STEP 2 Loosen the rear Trigger Frame Screw located underneath the rear Receiver This will allow all internal parts such as the Striker Plug with the Velocity Adjuster amp Spring Guide Striker Spring Striker Buffer and Striker Bolt to slide from the rear of the Receiver NOTE Remove the rear Trigger Frame Screw when the marker is in the un cocked position This way the tension of the Striker Spring will not allow the markers internals to spring out HELPFUL TIP Placing your finger behind the Striker Plug before removing the rear Trigger Frame Screw will prevent the markers internals from springing out STEP 3 Remove items in order Striker Plug w Velocity Adjuster Striker Spring and Striker Buffer STEP 4 Slide the Striker Bolt out of the rear of the Receiver HELPFUL TIP When the internals are removed it would be wise to clean any dirt or paint from the inside of the Receiver with a squeegee Wipe clean the Delrin Bolt with a rag or paper towel Apply some paintball gun oil on Striker O ring periodically REASSEMBLE REAR INTERNALS STEP 1 Reinsert the Striker Bolt with Striker O ring facing toward the front of the marker with the flat spot of the Striker Bolt facing down NOTE Having the Power Switch ON will
8. 3 Blinks 10 ms cpf 5 amb 3 U Blinks 15 ms cpf 5 amb 4 5 Blinks 20 ms cpf 5 amb 5 ms millisecond cpf cycle percentage filter amb anti mechanical bounce CAUTION A low Trigger Debounce setting such as Level One 1 may cause the marker to read trigger switch bounce as additional trigger pulls falsely generating shots or near full automatic fire SEMI AUTO MODE LOCK To lock the marker in Semi Auto Mode a small Circuit Jumper needs to be removed Circuit Board Removal of this Jumper will lock the Firing Mode in Semi Auto The Trigger Debounce setting will still be accessible but all of the other Firing Modes will be disabled To re enable access to all Firing Modes simply place the Circuit Jumper back onto the Circuit Board NOTE The Trigger Debounce setting is still accessible after the Firing Mode has been locked in Semi Auto operation by removing the Circuit Jumper ADDITIONAL FEATURES Forced Shot If the eyes are enabled and the breach is empty but you want to fire a clearing shot a forced shot can be initiated by pulling and holding the trigger for 1 2 second This is useful when you have emptied all your paintballs from the marker and would like to un cock or discharge the remaining air inside the marker Battery Power Indicator If battery power is sufficient when the marker powers on the LED indicator will Flash Green rapidly If the battery power is low the LED will Flash Red rapidly indicating that the
9. ease reentry of the Striker Bolt Apply thumb pressure behind the Bolt and at the same time pull on the Trigger Repeat this process until the Bolt is fully inserted NOTE The hole on the Striker Bolt should be facing upright when looking thru the Receiver STEP 2 Insert the Striker Buffer flush with the Receiver and place the Striker Spring thru the Striker Buffer STEP 3 Place the Striker Plug w Velocity Adjuster amp Spring Guide to the rear of the Receiver and tighten the Trigger Frame Screw STEP U Insert the Delrin Bolt thru the rear of the Receiver with the Top Cocking Knob Press downward on the Top Cocking Knob to gain entry with the Striker Bolt NOTE If the Striker Bolt hole is not aligned upright the Top Cocking Knob will not fasten correctly HELPFUL TIP Use a small tool to align the hole upright should the Striker Bolt turn when positioned back in the receiver WARNING Before after use of the marker make sure to fasten all screws Screws may become loose due to vibration Loose screws can be dangerous and cause injury To assure that the marker is assembled properly follow the schematic drawing or position parts in order during disassembly Parts assembled backwards or improper parts installed will can cause the marker to malfunction AJAMMED PAINTBALL IN THE BREACH In the event of a paintball break and the Delrin bolt jams follow these steps to help un jam the marker The markers breach is located where the barrel starts to t
10. o ring e Dirt or broken paint shell fragments inside the receiver can cause the marker to have recocking issues Using a squeegee through the upper portion of the receiver will remove most of the dirt or broken shell fragments Should this issue continue see Disassemble Reassemble remove the markers internals for complete cleaning Using low quality paintballs can cause the marker to experience recocking issues because of the shape of the paintballs HELPFUL TIP Paintballs have a shelf life and can become too fragile for use HELPFUL TIP Paintballs can take a different shape over time so it would be wise to size the paintball with your barrel ELECTRONIC GRIP TROUBLESHOOTING If your marker is not shooting it may be due to one of the following problems e Battery may need to be recharged e The Battery Wire Harness is not properly attached to the circuit board e The Coil Set Harness is not properly attached to the circuit board e The Touch Switch Harness is not properly attached to the circuit board NOTE If the Markers Electronics have any dirt or paint Kingman recommends using an aerosol can of air Apply the can of air directly at the components that need cleaning AIR LEAKS IMPORTANT Always remove the air tank before any disassembling of the marker e Air leaking from the Lower Pressure Chamber means the O ring ORGOO2 will need to be oiled or replaced e Air leaking from the Vertical Adapter means the O ring 4 ORGOO2 wil
11. the Eye Panel Screw CHANGING THE BALL STOPPERS Experiencing paint rolling through the barrel can be related to small diameter paintball s or the loss of a Ball Stopper s BLSOO2 When removing Eye Panel Screws SCROOU and Eye Panels BLSO21 the Ball Stopper s will be accessible for cleaning or replacement HELPFUL TIP Please note how the parts are removed for easy reassembly IMPORTANT Before removing both Eye Panels use a needle or dental pick thru the hole of the Eye Panel to remove any dirt that can build up and block the Allen screw from loosing It s possible if the dirt is not removed you can stripe the Eye Panel Screw NOTE Take precaution not to over tighten the Eye Panel Screws or this can strip the head CUP SEAL REMOVAL STKOO1 STPO21 ITPOO2 TPOO1 VRTOO1 TPOO3 Part Names and Part Numbers describe in this selection Cup Seal ITPOO1 Trigger Frame Screw SCROO1 Valve Spring SPROO2 MUx8 Head Screw SCROO2 Inline Regulator REGOO1 Receiver RECO21 Trigger Frame TRFOO2 Valve Body ITPOO3 Vertical Screw SCROO8 9 6 Rechargeable Battery JE1015 Eye Wire Harness WRHOO6 Velocity Adjuster amp Spring Guide VTAO21 Valve Body Screw SCROO7 Delrin Bolt VBTOO1 Striker Plug STPO21 Striker Spring SPROO1 Top Cocking Knob STKOO1 Striker Bolt Mini STBOO1 Valve Pin ITPOO2 Striker Buffer STFO01 Vertical Adapter w Gauge VRTOO1 parts not shown STEP BY
12. to be adjusted or altered If the Eyes are ON and do not see each other when firing your marker you will have to clean the Eyes CLEANING THE ANTI CHOP EYES Using a squeegee or swab thru the breech should clean the Eyes enough for the Eyes to detect each other Another way is to use an aerosol can of air thru the breech to remove any paint or dirt To thoroughly clean the Eyes using the supplied Allen wrench remove both Eye Panel Screws SCROOUY and Eye Panels BLSO21 Once the Eye Panel Screws amp Eye Panels are removed proceed with a soft pinch to remove the Eye Wire Harness WRHOO6 from the receiver Use a cloth or paper towel to remove any paint or dirt that is blocking the Eyes IMPORTANT Cleaning the Eyes often will help reduce dirt paint or oil residue that blocks the Eyes NOTE Never attempt to rush the cleaning process or you can pinch the wires and cause the marker to malfunction with the Eye Mode ON Take precaution not to over tighten the Eye Panel Screws or this can lead to stripping the head NOTE When the Eye Panels are removed the Ball Stopper s BLSOO2 may be attached to the Eye Panels and can cause them to fall out HELPFUL TIP Please note how the parts are removed for easy reassembly IMPORTANT Before removing both Eye Panels use a needle or dental pick thru the hole of the Eye Panel to remove any dirt that can build up and block the Allen screw from loosing It s possible if the dirt is not removed you can strip
13. H TIP Notice how the Striker Bolt Mini is placed in the Receiver before removed to ease re entry STEP 5 Loosen the Vertical Screw counter clockwise to allow the Vertical Adapter w Gage to release from the Receiver STEP 6 Loosen the Valve Body Screw counter clockwise to allow access to the Valve Body STEP 7 Use a plastic or wooden dowel rod to push the Valve Body from the rear of the Receiver thru the front of the Receiver TECH TIP Use an 8 or longer rod thru the lower rear section of the Receiver Notice how the Valve Body is placed inside the Receiver before removing This will help ease re entry after installing the new Cup Seal STEP 8 Untuist both half s of the Valve Body to gain access of the Valve Pin STEP 9 Untwist the Cup Seal from the Valve Pin Replace the defective Cup Seal HELPFUL TIP Please note how the parts are removed for easy reassembly CAUTION Use the proper Allen wrenches to fasten all screws and never apply more force than necessary IMPORTANT Always remove the Air Tank before any disassembly of your marker Do not remove the Valve Body ITPOO3 unless specific Valve Body repairs are needed Do not remove the Valve Body with a screwdriver as it will damage the Valve Body and cause air leaks REGULATOR MAINTENANCE SCHEMATICS WARNING Never at any time should you attempt to OS unscrew the Vertical Regulator while the marker is pressurized Doing so can cause serious injury or death 502025 IMPORTANT Mar
14. STEP A WARNING Never at any time should you attempt to unscrew the Vertical Regulator while the marker is pressurized Doing so can cause serious injury or death HELPFUL TIP The sign of a worn Cup Seal is the presence of Compressed Air leaking down the barrel STEP 1 Twist the Inline Regulator counter clockwise to release off the Vertical Adapter w Gauge The hose line will hold the Inline Regulator when it dangles from the C A On Off STEP 2 Remove all three MUx8 Screws on the left side of the Trigger Frame The Grip Panels will allow access to the Circuit Board STEP 3 Gently detach the Eye Wire Harness from the Circuit Board This will allow maneuvering around certain parts HELPFUL TIP Gently move aside the Rechargeable Battery out of the Trigger Frame to view the Eye Wire Harness Gently remove the Eye Wire Harness thru the coil set channel exiting thru the top of the Trigger Frame STEP U Remove both Trigger Frame Screws This will then allow the Trigger Frame to disconnect from the Receiver Pull upward on the Top Cocking Knob to allow the Delrin Bolt to release from the Striker Bolt Mini Once the Striker Plug has been removed the Striker Spring Striker Buffer and Striker Bolt Mini need to be removed out the rear of the Receiver 12 13 TECH TIP Before loosening the rear Trigger Frame Screw place your finger in front of the Striker Plug so the internal parts don t spring outward if the Delrin Bolt is in the cocked position TEC
15. arker Be sure that the valve is turning D A N G E R with the cylinder rather than remaining stationary with the marker STOP if the Valve starts to unscrew from the cylinder If in doubt screw the cylinder back onto the marker and contact a trained person for repair COMPRESSED AIR TANK WARNINGS Compressed Air Tank can fly off with enough force to cause serious injury or death if the Valve unscrews from the cylinder head LOOK at the Valve when removing the cylinder from the marker Be sure that the valve is turning with the cylinder rather than remaining stationary with the marker STOP if the Tank Valve starts to unscrew from the cylinder If in doubt screw the cylinder back onto the marker and contact a trained person for repair COMPRESSED AIR TANK WARNINGS e All valves must only be installed or removed by a qualified airsmith e See Compressed Air tank labels for retest dates Cylinder tanks must be retested periodically e Improper use filling storage or disposal of all air cylinders may result in death personal injury and or property damage Always keep cylinders out of reach from children or any inexperienced person s e Only properly trained personnel in accordance with CGA Pamphlets P 1 and G 6 3 must fill all air cylinders Pamphlets are available from the Compressed Gas Association or www CGANET com e Never alter the cylinder in any way DO NOT expose pressurized cylinders to temperatures in excess of 130 F 54 C
16. battery will need to be charged Sleep Mode After fifteen 15 minutes of inactivity the Circuit Board will automatically power down thus saving battery power TRIGGER ADJUSTMENT Adjusting the Top Screw SCROO6 located underneath the Trigger Frame clockwise will swing the trigger closer to the touch switch NOTE Adjusting the screw counter clockwise will increase the trigger gap HELPFUL HINT Over adjusting the screw to close won t allow the trigger to activate the touch switch which will not allow the marker to fire Adjusting the Middle Screw SCROO6 clockwise will shorten the trigger stop the touch switch NOTE This will increase trigger sensitivity Unscrewing it counter clockwise will decrease trigger sensitivity Adjusting the Lower Screw SCROOS clockwise will shorten the distance on trigger pull VELOCITY ADJUSTMENT INCREASE DECREASE To INCREASE your velocity FPS Feet Per Second using the Allen wrench turn the Velocity Adjuster Spring Guide VTAO21 clockwise To DECREASE your velocity FPS Feet Per Second using the Allen wrench turn the Velocity Adjuster Spring Guide VTAO21 counter clockwise NOTE Velocity Adjuster Spring Guide VTAO21 doesn t remove from the rear of the Sticker Plug 4STPO21 RECOMMENDED To guarantee proper adjustment Kingman recommends using a chronograph to ensure the markers
17. ger that is NOT a Spyder Product Doing so will VOID all electronic warranties and liabilities from Kingman WARNING e Spyder Electronic Markers are not water resistant e Extreme moisture can cause serious damage to any Spyder Electronic Marker e Always clean any dirt or paint inside the markers electronics e Never attempt to modify the electronics circuitry doing so will VOID all electronic warranties and liabilities from Kingman BATTERY CHARGING SPYDER LED A C CHARGER INSTRUCTIONS To charge a Spyder 9 6 NiMH Battery the circuit board must be in the OFF Position Spyder Batteries JE1015 not pictured are not fully charged when purchased Using the supplied rea E Spuder LED A C Charger JE1029 Kingman recommends a 4 E1029 charging time of 5 hours for a complete charge STEP 1 Plug the Spyder LED A C Charger into a 110v 120v power outlet a STEP 2 Connect the Spyder LED A C Charger cord to the rear of the markers trigger frame STEP 3 The LED indicator on the A C Charger will display RED when the battery is charging STEP U The LED indicator on the A C Charger will display GREEN when the battery is fully charged STEP 5 Unplug the Spyder LED A C Charger cord from the rear of the markers trigger frame STEP 6 Remove the Spyder LED A C Charger from the 110v 120v power outlet NOTE It is recommended that the battery be charged prior to use in order to ensure maximum performance especially if the battery
18. has not been used in over a week IMPORTANT You should never charge the battery over 24 hours or you can run the risk of damaging the battery or electronics ELECTRONICS amp SETTINGS UPPER JA a POWER LED LIGHT e ANA BUTTON MODE BUTTON LOWER LED LIGHT CIRCUIT BOARD SETTINGS AND LED COLOR FUNCTIONS POWER AND EYE OPERATION Press the Power Button to turn marker on The Tadao Circuit Board will boot instantly showing a Solid Red LED in the grip frame The marker will be in Safe Mode when the marker is first turned on to disable the Safe Mode press and release the Power Button once When the Safe Mode is disengaged the LED will switch to Solid Green if the eyes detect a paintball in the breach or if the marker is un cocked The LED will display a Blinking Green light if there is no paintball in the breach and the marker is cocked To disable the eyes press and hold the Mode Button for one second The LED will switch to Blinking Red to indicate that the eye system is disabled To turn the marker off press and hold the Power Button until the LED will turns off when the board powers down To determine if the eyes are working correctly insert an inanimate into the breach and observe whether or not the LED changes from Blinking Green to Solid Green and back to Blinking Green once the object is removed LED DISPLAY MEANING Solid Red Safe Mode Blinking Red Eyes disabled Rate of fire capped at 1Obps Solid Green Ball in Breach
19. hread in the receiver and underneath the markers feed neck Before attempting to un jam the Delrin bolt you should always have your Goggles or Safety Glasses on Make sure the marker is in the SAFE OFF position before attempting to un jam the Delrin bolt Remove the Compressed Air Tank 10 11 before attempting to un jam the marker Remove all paintballs and the loader from the feed neck Have the barrel removed from the receiver to allow the paintball s to exit With enough force tension on the Cocking Knob pull back to release the Delrin bolt from the jammed position Another method is to use a Straight Shot Sgueegee or the end of a wood dowel rod push against the face of the Delrin bolt with enough force to release the jammed bolt Always clean the paint from the breach and barrel to enhance the performance of your marker IMPORTANT Never look down the barrel of the marker when loaded or unloaded Remove the attached Compressed Air Tank before attempting to un jam the Delrin Bolt NOTE Never use a metal rod or screwdriver as a tool to push on the Delrin bolt anything metal will scratch and damage the inside of the marker ANTI CHOP EYES SCROOYW BLSOe1 LA A T The Anti Chop Eyes help prevent the chopping of paint by not allowing the marker to fire until a paintball is properly chambered in the breach The Eyes transmit a beam across the inside of the breech The circuit board is preset from the factory and does not need
20. iring the marker you should ALWAYS remove the Compressed Air Tank before storing When the tank is being removed excess air will release from the C A On Off adapter 4 ASAOO20 CAUTION Never expose any skin to the C A On Off adapters bleed hole when removing the tank This is to avoid the risk of getting skin burn from the escaping GAS IMPORTANT You should never need to use any hand tool to detach a Compressed Air Tank from the C A On Off adapter If you cannot remove a tank by hand please see a certified airsmith for assistance PROPER USE OF YOUR BARREL BLOCKING DEVICE A Barrel Blocking Device or BBD is an essential part of your paintball safety equipment The Barrel Blocking Device is designed to stop a paintball from exiting a paintball marker accidentally Improper use of the Barrel Blocking Device will render this device useless STEP 1 Place the bag sock part of the Barrel Blocking Device over the end of your barrel and wrap the elastic cord around the back end of your marker STEP 2 Adjust the length of the elastic cord to make sure your Barrel Blocking Device fits securely over your markers barrel NOTE If the elastic cord is too long you can tie a couple of knots around the cord to shorten its length STEP 3 Remove the Barrel Blocking Device only when you are getting ready to begin play or have been instructed to do so by a field safety official STEP U Always keep your Barrel Blocking Device on your marker after you have finished
21. kers that are equipped with a regulators may store residual air after the Compressed Air Tank has been removed To fully remove any residual air stored in the marker turn the C A On Off adapter knob ASAO17 not pictured counter clockwise to shut off the air supplied from the tank Take several dry fire shots with the marker pointed in a safe direction until the Gauge GAGOOZ2 not pictured ORGOZ2 reads Opsi and the marker should decock REGOOG Apply a small amount of grease on part numbers Reg Piston O ring 4ORGO21 and Reg Adjuster O ring ORGO22 Having the Regulator in its optimal performance G scroz6 you should maintain a clean and dirt free regulator JABS Depending on the usage of your marker it s a good idea to practice cleaning inside regulators internals TECH TIP Using grease like Dow Corning 33 medium consistency or any paintball grease on the following parts listed will maintain the functioning of your Regulator HELPFUL TIP Please note how the parts are removed for easy reassembly TROUBLESHOOTING ONE OR MORE OF THE FOLLOWING MAY CAUSE RECOCKING RELATED ISSUES e The pressure in the tank is too low and possibly needs to be refilled e Need lubrication on the following Striker O ring ORGOO might be damaged or missing Replace with a new Kingman approved Striker O ring see Disassemble Reassemble NOTE The Striker O ring can not be substituted with a black or urethane bottle
22. l need to be oiled or replaced e Air leaking down the barrel is usually a Cup Seal ITPOO1 that is worn or damaged see Cup Seal Removal The Cup Seal should the exchanged e Never remove Valve Body ITPOO3 unless specific repairs are needed e Anick or scratch on the lip of the Valve Body can cause an internal air leak see Cup seal Removal The Valve Body may need to be replaced e Air leaking thru the Receiver and out of the Trigger Frame would indicate the Valve Body O rings ORGOO2 will need to be replaced e If air is leaking thru the opposite end of the hose fittings please check the following The Female end of the Hose must have a plastic washer 4 HSFOOU installed inside the hose collar and be tightened properly HELPFUL TIP To assure marker is assembled properly follow the schematic drawing or position parts in order during disassembly Parts assembled backwards or improper parts installed will can cause the marker to malfunction WARRANTY STATEMENT Kingman warrants the original retail purchaser that this product is free from defects in material and workmanship under normal use and service for a period of 1 year from the original date of purchase Any Electronic Components in an Electronic Spyder marker are warranted for 3 months from the original date of purchase Kingman agrees to repair or replace at its discretion any product within a reasonable period of time This warranty does not cover o rings cup sea
23. loose due to vibration Loose screws can be dangerous and cause injury HELPFUL TIP It s a good practice to lubricate your marker before and after each use especially when storing the marker for an extended period of time Add a few drops of paintball gun oil or marker grease on the Striker O ring ORGOO1 see Disassemble Reassemble Before storing the marker make sure the marker is in the un cocked position This will help the main spring maintain its tension IMPORTANT Firing velocity may vary according to altitude and climate conditions Before using your marker in play you must always first perform a SAFE VELOCITY TEST This can only be accomplished by using a testing device called a Velocity Chronograph and can be performed at a paintball dealership or local playing field NOTE This product is intended to be used at a velocity no greater than 300 feet per second fps This product is NOT intended to be used at any distance less than 25 feet This paintball marker may have excess gas after the removal of the Compressed Air Tank Please remove all paintballs and discharge the remaining gas safely Never store a Compressed Air Tank attached on the marker while not supervised COMPRESSED AIR TANK WARNINGS WARNING UNSAFE The CO2 or Compressed Air Tank can fly off with enough force to cause serious injury or death if the Valve unscrews from the cylinder head LOOK at the Valve when removing the cylinder from the m
24. ls 9 6v rechargeable battery charger scratches nicks normal wear and tear of parts any modifications normal fading of anodizing and damage caused by dropping or hitting of products This warranty shall not apply if it is shown by a Kingman Technician that the consumer caused the defect or malfunction because of misuse This warranty only covers original factory parts Any modifications or tampering of original factory parts will VOID warranty and liabilities from Kingman Any damage caused by water will not be covered under warranty Warranty repair can only be conducted by Kingman technician or Kingman authorized technician For warranty to be effective consumer must return the enclosed warranty registration card filled out along with a copy of the purchase receipt within 15 days of the original purchase date This warranty is not transferable Paintball markers are non refundable This warranty will not cover pick up shipping delivery and or house calls If product needs repair consumer will package it carefully and send together with your name address phone number and a brief description of the malfunction to KINGMAN GROUP Attn Tech Department 14010 Live Oak Avenue Baldwin Park CA 91706 U S A www kingman com Friday from 8am to Spm PST and can be reached at VIIK 626 430 2300 wwuw spydertv FOR TECHINICAL SUPPORT Our Technical Support Department is open Monday through 14 15 RSX PARTS LIST ASAOl2 ASAO13 ASAO17
25. ot attempt to service the regulator unless you have received proper training from a gualified Kingman Group service technician Doing so will VOID all regulator warranties and liabilities from Kingman Group If you experience any leaks or problem with the regulator contact Kingman Group Technical Support Service Department IMPORTANT Always remove all paintballs and Compressed Air Tank from your marker and remember to keep the marker in its un cocked position before placing it in storage DISASSEMBLE REASSEMBLE AND CLEANING OF REAR INTERNALS Top Cocking Pin STKOO1 Striker Spring SPROO1 Delrin Bold VBTOO1 Striker Buffer 4STFOO1 Striker Bolt STBOO1 Trigger Frame Screw SCROO1 Striker Plug STPO21 Velocity Adjuster amp Spring Guide VTAO21 Striker O Ring ORGOO1 Saber Trigger 4TRSOO5 QUICK CLEAN DISASSEMBLE Lift upward on the Top Cocking Knob This will allow the Delrin Bolt to slide from the rear of the Receiver HELPFUL TIP Removing the Delrin Bolt from the Receiver will allow easy access to clean with a squeegee NOTE Make sure the hole on the Striker Bolt is facing upright when looking thru the Receiver This will allow the Top Cocking Knob to correctly fasten with the Striker Bolt IMPORTANT The air passage hole located in the middle of the Delrin Bolt should always be facing downward when reinstalling If the Delrin Bolt is not installed correctly paintballs will not exit out of the barrel normally
26. playing Keep it in place even after you have emptied all paintballs and removed your air tank from your paintball marker WARNING Make sure the Barrel Blocking Device fits securely over your barrel with the elastic cord tight and have sufficient tension This will prevent the Barrel Blocking Device from coming off the end of the barrel during an accidental paintball discharge Inspect your Barrel Block Device regularly for wear and any tear if it is worn replace it immediately Always have your Barrel Blocking Device in place on your markers barrel to insure safety and prevent accidents that may cause permanent injury or even death BATTERY INSTALLATION gt NOTE Battery must be fully charged before initial use SCROO2 STEP 1 Remove the three MUx8 Screws SCROO2 and F WRHOOZ2 left side Grip Panel GRPOO STEP 2 Attach the Spyder Battery JE1015 to the Battery Harness WRHOOZ2 STEP 3 Re tighten the three MUx8 screws SCROO2 HELPFUL TIP Please note how the parts are removed for easy reassembly 31202 EE N SPYDER 9 6 NiMH BATTERY LIFE Always use the supplied Spyder 9 6volt NiMH Battery and Spyder LED A C Charger to operate this marker A fully charged Spyder Battery will last about 3 000 to 5 000 shots Under normal use and charging conditions the expected life of the Spyder 9 6 NiMH Battery to is approximately 700 1 000 charging cycles WARNING This marker is not intended to use any normal 9 volt battery or char
27. ring Guide VTAO21 clockwise will increase the velocity fps while turning counter clockwise will decrease the velocity fps NOTE This marker is equipped with a Regulator dial that can adjust the pressure from O 600Opsi see Regulator Adjustment NOTE Your marker is intended to be used in a paintball facility with the proper paintball protection IMPORTANT Kingman recommends using a chronograph to ensure that the maker s velocity is under 300 fps When finished playing remove all paintballs from the paintball loader before detaching from the markers feed neck CAUTION There may be a paintball in the marker s breach take a couple of shots in a safe direction to make sure the barrel and receiver are empty Place the barrel blocking device over the barrel tip This will help avoid any accidental discharge Kingman recommends having the marker in the SAFE or OFF position after use Unscrew the Compressed Air Tank from the marker s C A On Off adapter Turning the tank counter clockwise will detach it from the marker s C A On Off adapter CAUTION Never expose any skin underneath the C A On Off adapters bleed hole when removing the tank This can run the risk of getting skin burn from the releasing of the GAS IMPORTANT You should never need to use any hand tool to detach a Compressed Air Tank Store the marker in a paintball bag or in a safe place WARNING Before after use of the marker make sure to fasten all screws Screws can become
28. rrel for safety precautions when the marker is not in use Install and charge the battery see pages see Battery Charging Installation Attach the Compressed Air Tank to the C A On Off adapter HELPFUL TIP Make sure to have the Compressed Air Tank filled before attaching to the marker Tighten the Compressed Air Tank clockwise in the markers C A On Off adapter until it is snug If an air leak occurs between the tank and the C A On Off adapter replace the urethane bottle O ring NOTE O rings in the markers parts kit are not supplied to attach with a Compressed Air Tank IMPORTANT You should never need to use any hand tool to attach a Compressed Air Tank to the C A On Off adapter Attach an electronic loader on the Twist Clamp FNDO21 twist clockwise to fasten and counter clockwise to release the loader Only use 68 caliber paintballs through the loader NOTE Kingman recommends that you use a force feed high speed electronic loader to reach optimum performance Cocking the marker Pull the Top Cocking Knob STKOO1 rearward until the Delrin bolt latches CAUTION Should you let go of the Top Cocking Knob before it latches your marker may fire Remove the barrel blocking device CAUTION With the power switch turned ON the marker is LIVE Pulling the trigger TRSOOS will fire a paintball IMPORTANT Only test your marker in a safe direction or in a designated playing field Performing a velocity fps check Turning the Velocity Adjuster Sp
29. s than 200psi the marker may experience some re cocking issues To achieve the desired pressure setting slowly turn the Reg Adjuster Counter Clockwise in small increments and watch the Gauge GAGOO2 not pictured while making the adjustment When adjusting the Regulator to Decrease the output pressure you will need to fire the marker a few times to get the new setting to READ on the gauge IMPORTANT Make sure you have your marker pointed in a safe direction and you are following all safety guidelines set with the use of this product NOTE Any adjustments made to the Regulator Adjuster Screw after the marker has been chronographed will alter the marker s velocity fps HELPFUL TIP When adjusting the regulator output pressure always watch the Gauge not pictured to insure the right pressure setting It s a good practice to fire the marker a few shots every time an adjustment is made to the regulator this will allow the regulator to settle in to its new output pressure setting IMPORTANT Markers that are equipped with regulators may store residual air after the Compressed Air Tank has been removed To fully remove any residual air stored in the marker turn the C A On Off adapter knob ASAO17 counter clockwise to shut off the air supplied from the tank Take several dry fire shots with the marker pointed in a safe direction until the Gauge 4GAGOO2 not pictured reads Opsi and the marker should decock IMPORTANT Do n
30. utton once After the Firing Mode has been selected turn the marker off by pressing the Power Button Solid Purple Firing Mode 1 Blink Semi auto uncapped 2 Blinks Semi auto capped at 15bps 3 Blinks PSP Ramp capped at 15bps U Blinks Millennium Ramp capped at 15bps 5 Blinks 3 shot burst capped at 15bps TO ENTER DEBOUNCE PROGRAMMING MENU While the marker is off press and hold the Mode Button then press the Power Button and the LED will cycle through multiple colors until the LED displays Solid Purple for Firing Mode Setting Menu Press the Mode button once more and the LED will change to Solid Teal Blue for the Debounce Setting Menu TO CHANGE THE TRIGGER DEBOUNCE SETTING Press and hold the Mode Button until the Solid Teal Blue LED goes out The LED will blink to show the current Trigger Debounce setting For example if the current Debounce setting is on Level Three 3 the LED will blink three 3 times Once the LED stops blinking you will have two 2 seconds to enter a new setting To enter anew Trigger Debounce Setting press the Mode Button to select the new Trigger Debounce Setting For example to set the Trigger Debounce to the least sensitive setting a Level Five 5 you must press the Mode Button five 5 times After the Trigger Debounce setting has been selected turn the marker off by pressing and holding the Power Button Solid Teal Blue Trigger Debounce 1 Blink 1 ms cpf 1 amb 1 2 Blinks 5 ms cpf 5 amb 2
31. velocity is under 300fps Increase Velocity WARNING e The recommended Velocity speed should be no greater then 300 fps Not doing so can cause serious injury if the Velocity is dangerously high e Paintball markers are not intended to shoot any person less then 25 feet e Never point a loaded marker at any person who is not wearing the proper face protection e Never at any point should you look down the barrel whether the marker is loaded or not e Using a paintball marker outside a non designated paintball field can be illegal and is subject to law enforcement penalties if property damage is caused by the user C A ON OFF ADAPTER o Ny gt El HELPFUL TIP Make sure to have the Compressed Air Tank filled before use TD e Attach your Compressed Air Tank to the C A On Off adapter e Tighten the tank clockwise in the markers C A On Off adapter until it is snug If an air leak occurs between the tank and the C A On Off adapter replace the urethane o ring e To pressurize the marker turn the adapter knob towards the ON position to pierce the pin valve on the tank e To release the pressure turn the dial knob towards the OFF position This will release the pressure in the hose line IMPORTANT Markers that are equipped with regulators may store residual air after the Compressed Air Tank has been removed To fully remove any residual air stored in the marker turn the C A On Off adapter knob ASAO17 counter clock
32. wise to shut off the air supplied from the tank Take several dry fire shots with the marker pointed ina safe direction until the Gauge GAGOO2 not pictured reads Opsi and the marker should decock IMPORTANT You should never need to use any hand tool to attach a Compressed Air Tank to the C A On Off adapter NOTE O rings in the markers parts kit are not supplied to attach with a Compressed Air Tank NOTE The hose line adapter supplied on the C A On Off is American thread 1 8 NPT REGULATOR ADJUSTMENT WARNING Never at any time should you attempt to unscrew the Vertical Regulator while the marker is pressurized Doing so can cause serious injury or death The RSX is equipped with a Vertical Inline Regulator located in front of the markers trigger frame Once a Increase Compressed Air tank has been installed and tank valve Velocity is opened by turning the C A On Off adapter knob clockwise the marker is potentially capable and ready to Decrease Velocity fire To INCREASE the regulator pressure turn the Reg Adjuster REGOO6 Counter Clockwise with the regulator wrench REGOO6 To DECREASE the regulator pressure turn the Reg Adjuster Clockwise with the regulator wrench NOTE After any adjustment has been made to the Reg Adjuster the Reg Adjuster Lock Screw SCRO26 must be re tightened to prevent any accidental increasing or decreasing of air pressure TECH TIP If the regulator output SCRO26 pressure is les
33. y Kingman STRONGLY recommends that any person using this product or within range of this product while it is in use MUST wear EYE FACE PROTECTION designed specifically for the sport of paintball This includes but is not limited to performing a maintenance check and during target practice Kingman reminds the user that it is YOUR RESPONSIBILITY to protect your eyes face at all times and will not be held liable for injuries sustained when failing to wear the appropriate protection Never shoot or point your marker at a person that is not in a designated paintball facility and without proper paintball protection Treat every paintball marker as if it were loaded Never look down the barrel of a loaded or unloaded marker Always keep the paintball marker in SAFE or OFF mode until ready to operate Always remove the gas source before disassembly Fire only 0 68 caliber paintballs with this product Always make certain the bolt is in the un cocked position when marker is not in use Using a paintball marker outside of a non designated paintball field can be illegal and is subject to law enforcement penalties if property damage is caused by the user Transfer this instruction manual upon change of marker ownership OPERATION GUIDE START UP A WARNING Always keep the marker powered OFF or on SAFE until you are ready to fire 1 2 3 7 10 11 12 Always attach a barrel blocking device over the tip of the ba
Download Pdf Manuals
Related Search