Pacemaker® User's Manual Version 2.0
Contents
1. Pacemaker 2s Manual Version 2 0 Ai ch A N j Table of contents 1 SYSTEM REQUIREMENTS 1 1 Mac 1 2 PC 2 SUPPORTED AUDIO FORMATS 3 INTERFACE AND FUNCTIONS 3 1 Basic functions 3 2 Extended functions 3 3 Monitoring functions 3 4 Display layout 4 GETTING STARTED 5 CONTROLLING THE TWO CHANNELS 6 NAVIGATION AND TRACK SELECTION 7 MIX FUNCTIONALITY 7 1 Set cue point 7 2 Adjust BPM 7 3 Crossfader and lineout 7 4 Beatmatch 15 Headphones monitoring 7 6 Headphones volume control 7 1 Adjust track EQ and gain 1 8 Adjust colour FX 7 9 Adjust beat FX 710 Adjust key FX 7 11 Kill all effects 7 12 Reverse play 7 13 Get loop 7 14 Adjust loop 7 15 Split double loop 8 RECORDING MIXES 9 CREATING AND MANAGING CASES 10 ADJUST SETTINGS 10 1 Mix control settings 10 2 Audio settings 10 3 Configure settings 10 4 Power settings 10 5 Mix mode settings 10 6 Play mode settings 11 CHARGING 12 COMPUTER SOFTWARE 13 SUPPORT 14 SAFETY INSTRUCTIONS AND REGULATION INFO 14 1 The FCC compliance statement 14 2 Industry Canada Statement 14 3 Korea Class B statement 14 4 VCCI Class B statement 14 5 Notice regarding disposal EU only oo OO OD OO d rd Oo Om A FWWNHN A NO MM P PO MM MM YP N ech ws S SS sch sch sch sch ch sch o OO oo OO P AN BOOT OO OO OO NS N OF P GO Go h MM OC OO CH 1 System requirements 1 1 Mac e Mac with built in USB 2 0 port e Ma2. 3 Press play to load and start playback of the selected track Optionally e Press forward or rewind button to move to the next or previous letter in the track list effective only when the track list is sorted alphabetically e Tap north or south to move step by step along the list e Press cue to load the track as cued at first beat e Swipe the touchpad horizontally to load the track Depending on whether the setting autocue is enabled or not the track is cued or playback is started e Tap west or east to load the track Depending on whether the setting autocue is enabled or not the track is cued or playback is started Access track list filters 1 Enter the track list by double tapping the centre of the touchpad 2 Press and hold the P switch up to access track list filters 3 Navigate between the different filters by sliding your finger left or right on the touchpad By default you can filter on Case Mix Genre Artist Aloum and BPM or any combination of these Additional filters that can be optionally activated through the settings menu include Remix Label Year Added Key Rating Type and Bitrate 4 Browse through the active filter criteria by stroking up or down on the touchpad 5 Select and apply a filter by swiping left or right on the touchpad 6 Release the P switch to access the filtered out track list Optionally e Tap west or east to navigate between the different filters e Tap north or south to move
3. be disposed of according to local environmental regulations Power adapter sold separately Only use a Pacemaker power adapter with your Pacemaker Always connect the power adapter to an AC outlet of the correct voltage when charging your device Do not connect it to an outlet of voltage other than that for which the power adapter is intended The only way to shut off power to your power adapter completely is to disconnect it from the AC outlet The Pacemaker power adapter is a high voltage component and must not be opened for any reason 24 Operating and storage temperatures Use your Pacemaker in a place where the temperature is always between 0 to 35 C 32 to 95 F Store your Pacemaker in a place where the temperature is always between 20 and 45 C 4 and 113 F Keep foreign matter out of your Pacemaker Never use your Pacemaker or the power adapter nearby liquids such as drinks bathtubs shower stalls etc If liquid gets into the device it could cause a break down fire or electrical shock Protect your Pacemaker and the featured power adapter from direct sunlight and rain or other moisture Make sure to not spill any food or liquid on Pacemaker or the power adapter If foreign matter gets into the device unplug the power adapter from the wall outlet and power off the device Interference with other electrical devices Radios and televisions placed nearby Pacemaker may experience reception inter ference Oper
4. button is lit while the forward loop end point button is blinking e The loop symbol is blinking at the top centre of the display Set loop end point 2 With the P switch still held up press forward to set the loop end point 3 Release the P switch e The loop is now set and the track segment loops between the set in point and end point e The cue forward and rewind buttons are blinking e The loop symbol is displayed at the top centre of the display Exit loop 4 With the P switch held up press cue e The track will assume normal playback from the previously set loop end point e The cue button is blinking e The play symbol is displayed at the top centre of the display Re enter loop 5 With the P switch held up press cue e The track segment loops between the previously set in point and end point e The cue forward and rewind buttons are blinking e The loop symbol is displayed at the bottom centre of the display 12 The loop will be cancelled if you perform one of the following actions between setting the loop in point and end point Release the P switch reverse the playing direction or change the tempo A loop is automatically exited if you cue fast forward or rewind a track within an activated loop Once defined a loop is permanently saved and can be re activated even after another track has been loaded You can only have one loop per track If you set a new loop in a track the previous loop defin
5. cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and the receiver 3 Connect the equipment into an outlet on a circuit different from that which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help 5 Unauthorized changes or modification to this system can void the user s authority to operate this equipment Responsible party contact for FCC matters only Tonium AB Box 20075 S 104 60 Stockholm Sweden 14 2 Industry Canada Statement This class B device meets all requirements of the Canadian interference causing equipment regulations Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada 14 3 Korea Class B statement Ba 77102 3 5547 7 ol JIZZ 788 BE 2E AR 5 J 7 BA FE 78014 ASE AS SH BE ASA ASS Tr gel i P ma 14 4 VCCI Class B statement ERNERBESRBEHBEHEUTCOUT DEE ERNEREFERBEB FH HR ZS VCCN DFELEDI lt SF FABERBRIRE TI ZTCOREIRERFTEHENZZETHN EUTIN EIN COMBMIVAPTLEVaYV S
6. mixes on the Internet and let anyone listen anytime Start recording a mix When in Mix mode select Settings gt Mix save gt Stop recording a mix Select Settings gt Mix save gt and choose from Save Discard or Cancel Halt your mix Select Settings gt Halt gt and then select option in the menu and swipe right 1 Continue gt to continue mixing 2 Save gt to save the current mix 3 Lock gt to lock the device from input 4 New gt to start recording a new mix 14 9 Creating and managing cases You can create and manage cases playlists with your Pacemaker letting you group music at your preference Cases can be transferred to and from the Pacemaker Editor for playback and editing Create a new case 1 Enter the track list by double tapping the centre of the touchpad 2 Select a track that you want to add to the case 3 Press the settings button e A track list context menu is displayed 4 In the track list context menu select Add to case gt and then swipe right on the touchpad e An Add to case menu is displayed 5 In the Add to case menu select Create case gt and then swipe right on the touchpad e A new case is created 6 In the Add to case menu select the newly created case and then swipe right on the touchpad e The selected track is added to the case 7 Press the settings button to exit the track list context menu at any time Optionally e Select Add all to
7. relative tempo change is shown on the display The BPM value of the track is changed The current BPM value is shown at bottom of the display on the active channel When you re happy release the P switch Bend Stroke swiftly along the touchpad rim to temporarily accelerate or decelerate the track tempo e The track tempo is temporarily changed Bend pitch can be optionally enabled in the settings menu 7 3 Crossfader and lineout Set the lineout to channel 1 Slide your finger along the crossfader from right to left and position the crossfade indicator at maximum left e Only channel 1 is heard through the lineout output Set the lineout to channel 2 Slide your finger along the crossfader from left to right and position the crossfade indicator at maximum right e Only channel 2 is heard through the lineout output Set the lineout to blend channel 1 with channel 2 Slide your finger along the crossfader and position the crossfade indicator between the channels e A blend of channel 1 and channel 2 corresponding to the crossfade indicator position is heard through the lineout output You can crossfade between channel 1 and channel 2 independent of which channel is currently active The crossfader action is relative you can place your finger at any position on the crossfader and the crossfade indicator position will change relative to the input Optional crossfader types can be enabled in the settings menu 1 4 Be
8. right Activate deactivate vinyl pause This setting lets you select between a scrubbing vinyl style pause and a stuttering DJ pause 1 When in Mix mode select Settings gt Mix control gt Vinyl pause gt 2 Toggle between On Off by swiping right Set effect crossfader type This setting lets you select the crossfader type and optionally incorporate effects into the crossfader 1 When in Mix mode select Settings gt Mix control gt Effect x fader gt 2 Toggle between Bass Filter Off by swiping right Set headphones crossfader type This setting lets you select between a normal and a relative crossfade indication 1 When in Mix mode select Settings gt Mix control gt Phones x fader gt 2 Toggle between Relative Normal by swiping right 17 Deactivate activate beat graph This setting lets you select to visually monitor relative tempo and sync 1 When in Mix mode select Settings gt Mix control gt Beat graph gt 2 Toggle between Off On by swiping right Deactivate activate lineout warning This setting lets you disallow allow a warning dialogue when attempting to disrupt the lineout channel 1 Select Settings gt Mix control gt Lineout warning gt 2 Toggle between Off On by swiping right 10 2 Audio settings Set headphones range This setting lets you select appropriate impedance setting for your headphones 1 Select Settings gt Audio gt Phones gt Range gt 2 Toggle between Hi i
9. want to adjust When your finger reaches the rim of the touchpad you can alter the value of the selected audio effect by stroking along the rim in either direction Adjustments must be performed as one continuous gesture without releasing your finger from the touchpad EQ and gain level adjustments only apply to the current track Loading a new track will reset the EQ and gain level parameters to their default values You can combine all the different levels by changing them one at a time The location of the audio effects on the touchpad can be configured via the settings menu 7 8 Adjust colour FX Available effects Pacemaker lets you add Hi cut lo cut filter Wah and Crush colour effects The effects are accessed at locations on the touchpad that can be configured through the settings menu by default the Hi cut lo cut filter is located at west Wah and Crush are not enabled by default but can be optionally enabled and assigned via the settings menu Apply Hi cut lo cut filter 1 With the P switch held up swipe from centre to west on the touchpad e The current filter parameter value is displayed 2 Without releasing your finger from the touchpad stroke along the rim clockwise or anti clockwise to increase or decrease the value 3 When you re happy release your finger from the touchpad Adjustments must be performed as one continuous gesture without releasing your finger from the touchpad FX adjustments only appl
10. 1 Select the cases that you want to remove from your Pacemaker library on the Editor 2 Press the delete button on your computer and the mixes are removed Transfer mixes from the Editor to your Pacemaker 1 Select the mixes that you want to transfer from the Editor to your Pacemaker 2 Drag and drop the selected mixes from the Editor to the Pacemaker library These mixes will on the Pacemaker device be represented by track lists only The respective track start positions i e cue points will be transferred as cue points to Pacemaker when transferring mixes 22 Remove mixes from your Pacemaker 1 Select the mixes that you want to remove from your Pacemaker library on the Editor 2 Press the delete button on your computer and the mixes are removed Transfer cases from your Pacemaker to the Editor 1 Select the cases that you want to transfer from your Pacemaker to the Editor 2 Drag and drop the selected cases from Pacemaker library to the Editor library Transfer mixes from your Pacemaker to the Editor 1 Select the mixes that you want to transfer from your Pacemaker to the Editor 2 Drag and drop the selected mixes from Pacemaker library to the Editor library Export mix to digital audio file 1 Select the mix that you want to export to a digital audio file 2 Right click the mix and select Export to start exporting the mix 3 Select disk location and file name for the mix e The mix is rendered as a digital audi
11. SL TER SENDE SE BERAZERBITZENBHET BY aA SS lc Hts TIEL lt lt MIRALTCK ESL 26 14 5 Notice regarding disposal EU only This symbol means that according to local laws and regulations your product should be disposed of separately from household waste When this product reaches its end of life take it to a collection point designated by local authorities Some collection points accept products for free The separate collection and recycling of your product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment Le symbole ci dessus signifie que vous devez vous d barrasser de votre produit sans le m langer avec les ordures m nag res selon les normes et la l gislation de votre pays Lorsque ce produit n est plus utilisable portez le dans un centre de traitement des dechets agree par les autorites locales Certains centres acceptent les produits gratuitement Le traitement et le recyclage s par de votre produit lors de son limination aideront a pr server les ressources naturelles et a prot ger l environnement et la sant des tres humains Das Symbol oben bedeutet dass dieses Produkt entsprechend den geltenden gesetzlichen Vorschriften und getrennt vom Hausm ll entsorgt werden muss Geben Sie dieses Produkt zur Entsorgung bei einer offiziellen Sammelstelle ab Bei einigen Sammelstellen k nnen Produkte zur Entsorgung unentgeltlic
12. ate Pacemaker at a suitable distance from radios and televisions Do not make repair yourself Do not attempt to open your Pacemaker or power adapter disassemble it or remove the battery You run the risk of electric shock and voiding the limited warranty No user serviceable parts are inside Care If your Pacemaker becomes dirty unplug the power adapter from the wall outlet and power off the device then wipe it with a clean dry cloth Do not use liquid cleaners such as benzene or thinner or cleaning compounds or flammable polishes as they may damage your device Handling To avoid breakage do not apply excessive force to connectors jacks buttons or the display Be careful not to drop your Pacemaker when playing or transporting the device About your data Inadvertent operations or unexpected malfunctions may cause the contents of memory to be lost To safeguard your important data please save it on your computer Tonium AB will accept no responsibility for any damages resulting from loss of data 25 14 1 The FCC compliance statement This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 ofthe FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may
13. ater If you re recording a mix this setting en ables saving the current mix to continue with a new recording When in Mix mode select Settings gt Halt gt and then select option in the menu and swipe right 1 Continue gt to continue mixing 2 Save gt to save the current mix 3 Lock gt to lock the device from input 4 New gt to start recording a new mix Activate deactivate mix save This setting enables recording your mixes Saved mixes can be transferred to the Pacemaker Editor for playback and editing 1 When in Mix mode select Settings gt Mix save gt 2 Toggle between On Off by swiping right to start stop recording a mix Switch from Mix mode to Play mode This settings mode is for playing music without using the full range of functions available in Mix mode Play mode is more power efficient with up to three times longer operation time 1 When in Mix mode select Settings gt Play mode gt by swiping right 10 6 Play mode settings Switch from Play mode to Mix mode 1 When in Play mode select Settings gt Mix mode gt by swiping right Set repeat 1 When in Play mode select Settings gt Playback gt Repeat gt 2 Toggle between All One Off by swiping right Set shuffle 1 When in Play mode select Settings gt Playback gt Shuffle gt 2 Toggle between On Off by swiping right 20 11 Charging Pacemaker has a built in battery A fully charged battery last for about five hour
14. atmatch Auto beatmatch With tracks playing on both channels press and hold the P switch down and press play to instantly sync the tempo and phase of the track on the active channel with the track on the passive channel This one click operation can be performed at anytime when two tracks are playing Beat graph When tracks are playing on both channels you can monitor tempo and phase sync via the beat graph If the white bars in the beat graph are drifting to the right the tempo of the track playing on the active channel is higher than the track playing on the passive channel e Lower the tempo of the track on the active channel until the white bars stop drifting If the white bars in the beat graph are drifting to the left the tempo of the track playing on the active channel is lower than the track playing on the passive channel e Increase the tempo of the track on the active channel until the white bars stops drifting If the white bars are not aligned with the grey bars in the beat graph the phase of the track playing on the active channel is not synced with the track playing on the passive channel e Bend the track accordingly until the white bars are aligned with the grey bars When the white bars in the beat graph stop drifting the BPM of the two tracks on the two channels match When the white bars are aligned with the grey bars in the beat graph the phase of the track on the active channel is synced to the track on the pa
15. blend 4 Touchpad adjust phones volume 3 4 Display layout Adrian Lux feat Name Club Kid Pacemaker 0 83 127 1 OD Active channel s info displayed in this example ch1 OONOOROQAN Track time VU meter Track tempo change Current track BPM Playback status Engaged effects Artist track title and album Beat graph ch and ch2 Power status 4 Getting started Turning on To turn on your Pacemaker press the settings button Turning off To turn off your Pacemaker press the settings button and select shutdown from the menu Alternatively press settings for more than four seconds 5 Controlling the two channels Pacemaker s two independent audio channels let you play two tracks side by side Select a channel and do your creative adjustments on the fly Controlling the two independent channels To activate and control a channel press the appropriate channel button e The selected channel is activated and information about it is highlighted on the display e Any input will affect the active channel only e Adjustments on the crossfader will affect the audio output blend between both channels To control the other channel simply press the appropriate channel button to activate it 6 Navigation and track selection Select and play a track 1 Double tap the centre of the touchpad to access the track list 2 Stroke the touchpad vertically to move the cursor up and down the list
16. c OS X v10 4 4 or later Intel e Pacemaker Editor for Mac 1 2 PC e PC with built in USB 2 0 port e Windows XP Home or Professional or Vista e Pacemaker Editor for Windows Pacemaker Editor is included on the Pacemaker device hard drive To download the latest version go to www pacemaker net products editor 2 Supported audio formats e MP3 up to 320 kbps M4A AAC LC AIFF FLAC WAV Ogg Vorbis and SND 3 Interface and functions 3 1 Basic functions 10 OO JO Om P Lob ch Display Rewind search or skip track Forward search or skip track Channel 1 select for input Channel 2 select for input Play play or pause track Cue set or launch at cue point Crossfader ch1 ch2 lineout blend Menu enter or exit music library Touchpad navigate or adjust Settings USB connector Kill all deactivate or relaunch effects Power connector Lineout connector Phones connector 3 2 Extended functions With the P switch held up P switch enable extended input Rewind set adjust loop in point split double loop Forward set adjust loop end point split double loop Channel 1 view time played time left Channel 2 view time played time left Play reverse play Cue exit re enter loop Touchpad navigate adjust N a GO D rd Oo Om P 3 3 Monitoring functions With the P switch held down 1 P switch access monitoring functions 2 Play instantly sync track BPM and phase with parallel channel 3 Crossfader ch1 ch2 headphone
17. case gt in the track list context menu to add all tracks in the filtered track list to the case Add a track to an existing case 1 Enter the track list by double tapping the centre of the touchpad 2 Select a track that you want to add to the case 3 Press the settings button e A track list context menu is displayed 4 In the track list context menu select Add to case gt and then swipe right on the touchpad An Add to case menu is displayed 5 In the Add to case menu select My cases gt and then swipe right on the touchpad e A My cases menu is displayed 6 In the My cases menu select your desired case and then swipe right on the touchpad e The selected track is added to the case 7 Press the settings button to exit the track list context menu at any time Optionally Select Add all to case gt in the track list context menu to add all tracks in the filtered track list to the case 15 Remove a track from a case 1 Enter the track list by double tapping the centre of the touchpad 2 Press and hold the P switch up to access track list filters 3 Navigate to the Case filter 4 Select the case that you want to edit and release the P switch to access the filtered out track list 5 Select the track that you want to remove from the case 6 Press the settings button e A track list context menu is displayed 7 In the track list context menu select Remove gt and then swipe right on the touchpad e A Re
18. clockwise or anti clockwise along the rim to increase or decrease the value 3 When you re happy release your finger from the touchpad Adjustments must be performed as one continuous gesture without releasing your finger from the touchpad FX adjustments only apply to the current track Loading a new track will reset the FX parameters to their default values Only one beat effect at the time can be activated with Trans being the exception The location of the audio effects on the touchpad can be configured via the set tings menu 710 Adjust key There are two ways to manipulate the key of a track you can transpose a track key one octave up down in increments of halftones or you can tune a track pitch in percent of one halftone up down The Key effect has no assigned default location on the touchpad It can be assigned to any spot on the touchpad via the settings menu Adjust the Key transpose effect 1 Swipe from the centre to the allocated spot on the touchpad to set the Key value e The current key is shown on the display 2 Without releasing your finger from the touchpad stroke clockwise or anti clock wise along the rim to alter the key value up or down 3 When you re happy release your finger from the touchpad Adjust the Key tune effect 1 Swipe twice from the centre to the allocated spot on the touchpad to set Key pitch value e The current pitch value is shown on the display 2 Without releasing yo
19. e far kastas tillsammans med hushallsavfallet N r produkten har tj nat ut m ste den tas till en tervinningsstation som utsetts av lokala myndigheter Vissa tervinningsstationer tar kostnadsfritt hand om uttj nta produkter Genom att lata den uttj nta produkten tas om hand f r tervinning hj lper du till att spara naturresurser och skydda h lsa och milj 27 www pacemaker net 2009 Tonium AB All rights reserved all wrongs reserved Pacemaker and the Pacemaker logotype are registered trademarks of Tonium AB registered in Sweden and other countries Mac is a trademark of Apple Computer Inc registered in the US and other countries Windows is a registered trademark of Microsoft Corporation in the US and other countries All other product and company names are trademarks or registered trademarks of their respective owners Pacemaker Manual version 2 0 28
20. er to your computer via the featured USB cable 3 Wait for Pacemaker to be connected 4 Use Mac OS X Finder or Windows Explorer on your computer to navigate to the Pacemaker hard drive 5 Double click it and identify the appropriate Pacemaker Editor installation file for your operating system 6 Double click the Editor installation file and follow the instructions to install Software upgrades If you re connected to the Internet while running Pacemaker Editor you will auto matically be offered available upgrades for the Pacemaker device and Editor You can also manually check for latest upgrades of the Editor on www pacemaker net Transferring music between Editor and Pacemaker Power on your Pacemaker and connect it to your computer with the featured USB cable and start the Editor Transfer tracks from the Editor to your Pacemaker 1 Select the tracks that you want to transfer from the Editor to your Pacemaker 2 Drag and drop the selected tracks from the Editor to the Pacemaker library Remove tracks from your Pacemaker 1 Select the tracks that you want to remove from your Pacemaker library on the Editor 2 Press the delete button on your computer and the tracks are removed Transfer cases from the Editor to your Pacemaker 1 Select the cases that you want to transfer from the Editor to your Pacemaker 2 Drag and drop the selected cases from the Editor to the Pacemaker library Remove cases from your Pacemaker
21. h abgegeben werden Durch das separate Sammeln und Recycling werden die nat rlichen Ressourcen geschont und es ist sichergestellt dass beim Recycling des Produkts alle Bestimmungen zum Schutz von Gesundheit und Umwelt beachtet werden Questo simbolo significa che in base alle leggi e alle norme locali il prodotto dovrebbe essere eliminato separatamente dai rifiuti casalinghi Quando il prodotto diventa inutilizzabile portarlo nel punto di raccolta stabilito dalle autorit locali Alcuni punti di raccolta accettano i prodotti gratuitamente La raccolta separata e il riciclaggio del prodotto al momento dell eliminazione aiutano a conservare le risorse naturali e assicurano che venga riciclato in maniera tale da salvaguardare la salute umana e l ambiente El s mbolo anterior indica que de acuerdo con la legislaci n local la eliminaci n de este producto debe realizarse de forma separada de la de los residuos dom sticos Cuando este producto ya no pueda utilizarse Ilevelo a uno de los puntos de recogida especificados por las autoridades locales Algunos de estos puntos de recogida prestan el servicio gratuitamente La recogida selectiva y el reciclaje de su producto en el momento de desecharlo contribuir n a la conservaci n de los recursos naturales y garantizar n un procesamiento de los residuos respetuoso con la salud de las personas y con el medio ambiente Symbolen ovan betyder att produkten enligt lokala lagar och best mmelser int
22. h filters to select from when navigating your track library The following filters are available for activation deactivation Mix Case Album Artist Genre Label BPM Key Added Rating Type Bitrate Year and Remix 1 Select Settings gt Configure gt Track list filters gt 2 Toggle between On Off for a filter by swiping right 18 Set track listtype This setting lets you choose between linked both channels or split per channel track list 1 When in Mix mode select Settings gt Configure gt Track list gt 2 Toggle between Linked Split by swiping right Set displayed track time This setting lets you choose how to display track time 1 Select Settings gt Configure gt Track time gt Display gt 2 Toggle between Left Playedby swiping right Set end of track alert This setting lets you choose whether to display track time as time left in blinking red when less than 30 seconds is remaining of the track 1 Select Settings gt Configure gt Track time gt End alert gt 2 Toggle between Off On by swiping right Set audio effect palette layout This setting lets you configure the location for the different audio effects on the touchpad The following locations are available for configuration North East South West as well as P switch up and North P switch up and East P switch up and South and P switch up and West The following audio effects and audio properties can be assigned to the differe
23. he display 3 Adjust the current playback position forwards or backwards by searching stroking along the touchpad rim e The track is stuttering at its moving position e The play and cue buttons are blinking The DJ pause symbol is displayed at the top centre of the display Set the cue point by pressing cue The track is cued at its current position The cue button is lit The cue symbol is displayed at the top centre of the display e e e E Si With a set cue point you can optionally Revert a playing track to the set cue point by pressing cue e Play the track from the set cue point by pressing and holding cue The track will be cued again when you release cue The track will continue to play when press ing play before releasing cue Vinyl style pause can be optionally enabled in the settings menu Only one user defined cue point can be set per track Loading a new track will remove the previously set user defined cue point When autocue is enabled Pacemaker cues tracks at first beat Autocue can be optionally disabled in the settings menu Cue points can be defined in the Editor When transferring tracks from the Editor to Pacemaker the defined cue points will remain set until altered on the Pacemaker or in the Editor 7 2 Adjust BPM Change tempo With the P switch held up stroke along the touchpad rim clockwise or anti clockwise to increase or decrease the tempo e The track tempo is changed e The
24. incrementally up or down between the active filter criteria Select multiple track list filters in one list 1 Browse through the active filter criteria by sliding your finger up or down on the touchpad 2 Select multiple filters by pressing cue for the items that you want to add Applied filters are highlighted Disable filters Disable a previously selected filter by pressing cue for that entry Disable all previously selected filters by selecting the lt All gt entry in the active filter list Each channel s track list is by default independent A linked track list common for both channels can be optionally enabled in the settings menu 7 Mix functionality With all the functionality of a stationary DJ set up and a full set of professional audio effects together with superior monitoring functions Pacemaker gives you unlimited creative influence over your Music 71 Set cue point Set the cue point 1 With a track playing on the active channel press play to DJ pause the track at its current position e The track is stuttering at its current position e The play and cue buttons are blinking e The DJ pause symbol is displayed at the top centre of the display 2 Move the track playback position fast forwards or backwards by pressing and holding forward or rewind e The track is stuttering at its moving position e The play and cue buttons are blinking e The forward or rewind symbol is displayed at the top centre of t
25. ition is overwritten 714 Adjust loop Adjust the in point of an activated loop 1 With the P switch held up press rewind loop in point e The forward button is lit while the rewind button is blinking 2 Keep the P switch held up and search stroke along the touchpad rim clockwise or anti clockwise to move the in point forward or backward 3 When you re happy release the P switch Adjust the end point of an activated loop 1 With the P switch held up press forward loop end point e The rewind button is lit while the forward button is blinking 2 Keep the P switch held up and search stroke along the touchpad rim clockwise or anti clockwise to move the end point forward or backward 3 When you re happy release the P switch Loop adjust is only possible while looping 715 Split double loop Shorten a loop by splitting the distance from the in point to the end point 1 With the P switch held up press and hold rewind loop in point 2 Keep the P switch held up and rewind pressed while pressing and releasing forward to move the end point halfway towards the in point 3 Repeat pressing and releasing forward for further splitting of the loop 4 When you re happy release the rewind button or the P switch Lengthen a split loop by doubling the distance from the in point to the end point 1 With the P switch held up press and hold forward loop end point 2 Keep the P switch up and forward pressed while p
26. move from case menu is displayed 8 In the Remove from case menu confirm by selecting Remove gt and swipe right on the touchpad e The selected track is added to the case 16 10 Adjust settings Access settings With a track loaded press and release the settings button Adjust master volume This setting lets you adjust the master volume output for lineout 1 Select Settings gt Volume gt by stroking right and continuing stroking along the touchpad rim to desired level View status 1 Select Settings gt About gt Status gt Restore Pacemaker settings 1 Select Settings gt Restore all gt e All preferences and settings are restored to default factory settings e Your tracks and mixes will not be effected 10 1 Mix control settings Deactivate activate autocue This setting lets you select to disallow allow loaded tracks to be cued at first beat 1 When in Mix mode select Settings gt Mix control gt Autocue gt 2 Toggle between Off On by swiping right Deactivate activate loop travel This setting disallows allows loop in point to push end point and vice versa 1 When in Mix mode select Settings gt Mix control gt Loop travel gt 2 Toggle between Off On by swiping right Deactivate activate time stretch This setting disallows allows track key to be independent of track tempo 1 When in Mix mode select Settings gt Mix control gt Time stretch gt 2 Toggle between Off On by swiping
27. mp Low imp by swiping right Set headphones volume limit This setting lets you adjust and select the maximum volume level for the head phones jack 1 Select Settings gt Audio gt Phones gt Volume limit gt 2 Set preferred volume limit by stroking along the touchpad rim Set headphones EQ This setting lets you adjust and select equalization for the headphones jack 1 Select Settings gt Audio gt Phones gt Phones EQ gt 2 Select EQ register from Treble gt Mid gt or Bass gt by stroking right 3 Set preferred level by stroking along the touchpad rim Adjust master volume This setting lets you adjust the master volume output for lineout 1 Select Settings gt Audio gt Lineout gt Volume gt by stroking right 2 Adjust the master volume by stroking along the touchpad rim Set master EQ This setting lets you adjust and select equalization for lineout 1 Select Settings gt Audio gt Lineout gt Lineout EQ gt 2 Select EQ register from Treble gt Mid gt or Bass gt by stroking right 3 Set preferred level by stroking along the touchpad rim Deactivate activate normalized sound This setting lets you disallow allow all tracks to be automatically adjusted to the same relative volume level 1 Select Settings gt Audio gt Normalize gt 2 Toggle between Off On by swiping right 10 3 Configure settings Activate deactivate track list filters This setting lets you configure whic
28. nt locations Treble Mid Bass Gain Reverb Roll Echo Hi cut lo cut filter Crush Trans Wah and Delay 1 When in Mix mode select Settings gt Configure gt FX layout gt Edit gt 2 Toggle between different audio effects for the current location by swiping right Restore audio effect palette layout This setting restores the audio effect palette to its default values 1 When in Mix mode select Settings gt Configure gt FX layout gt Restore gt Set language This setting allows you to set the language for menus and dialogues Select Settings gt Configure gt Language gt Select your preferred language by swiping right 10 4 Power settings Set standby timer when inactive 1 Select Settings gt Power gt Standby gt 2 Toggle between Off 1 min 5 min by swiping right Set screen intensity 1 Select Settings gt Power gt Intensity gt 2 Toggle between Bright Low Medium by swiping right Set backlight timer 1 Select Settings gt Power gt Timeout 2 Toggle between Off 10 sec 30 sec by swiping right Set nightlight 1 Select Settings gt Power gt Nightlight gt 2 Toggle between On Off by swiping right Set buttons blink 1 Select Settings gt Power gt Buttons blink gt 2 Toggle between Off On by swiping right 19 10 5 Mix mode settings Halt operation This setting halts your current mix You can lock Pacemaker from input if you want to take a break and continue l
29. o file and saved to your computer Transfer rendered mix files from your computer to your Pacemaker 1 Import the rendered mix file to your Editor 2 Select the mix represented as a track in your Editor track library 3 Drag and drop the selected track from your Editor to your Pacemaker library e Exported mixes will be handled as tracks on your Pacemaker Eject Pacemaker 1 Click the Eject button to the left of the Pacemaker library on the Editor 2 Wait for your Pacemaker to clear the Do not disconnect screen before pulling the USB plug 3 Do not disconnect the USB cable while transferring data as this may be potentially damaging to your Pacemaker Publish a mix on the Internet 1 Select the mix you want to upload from the Editor 2 Click the Publish button to start the uploading process 3 Follow the instructions to publish your mix on the Internet It is not possible to transfer tracks from your Pacemaker to the Editor You can only transfer music to your Pacemaker via the Editor software Learn more about the Editor at www pacemaker net products editor 23 13 Support For Pacemaker service and support information visit the support forum and the FAQ section at www pacemaker net support 14 Safety instructions and regulation info Important notice to consumers This product has been manufactured according to strict specifications and voltage requirements that are applicable in the country in which it i
30. ressing and releasing rewind to double the distance from the in point to the end point 3 Repeat pressing and releasing rewind for further doubling of the loop 4 When you re happy release the forward button or the P switch Shorten a loop by splitting the distance from the end point to the in point 1 With the P switch held up press and hold forward loop end point 2 Keep the P switch held up and forward pressed while pressing and releasing rewind to move the in point halfway towards the end point 3 Repeat pressing and releasing rewind for further splitting of the loop 4 When you re happy release the forward button or the P switch 13 Lengthen a split loop by doubling the distance from the end point to the in point 1 With the P switch held up press and hold rewind loop in point 2 Keep the P switch up and rewind pressed while pressing and releasing forward to double the distance from the end point to the in point 3 Repeat pressing and releasing forward for further doubling of the loop 4 When you re happy release the rewind button or the P switch A set loop will continue looping until it is exited A split loop can only be doubled up to its original length Splitting and doubling a loop is only possible while looping 8 Recording mixes Any mix can be saved on your Pacemaker When transferring your mixes to the Pacemaker Editor you can edit and refine your mixes as you like You can also upload your
31. s in Mix mode or about fifteen hours in Play mode If you leave Pacemaker unused for a while you may need to charge it again Charge via USB 1 Power off your Pacemaker 2 Connect the featured USB cable to your Pacemaker 3 Connect the other end of the USB cable to your computer e Pacemaker displays a charging screen after a while the screen is turned off and the play button starts to blink When Pacemaker is charging via USB press the Settings button to enable a data connection to the computer Optionally Charge via power adapter sold separately 1 Connect the Pacemaker power adapter to your device using the jack labelled Power 2 Plug the adapter into an AC outlet Power status e When your Pacemaker isn t connected to a power source the powersymbol shows the current power status e f the powersymbol is blinking your Pacemaker needs charging Your Pacemaker will charge at different rates depending on the type of USB port you connect to For optimal charging time use the Pacemaker power adapter 21 12 Computer software Pacemaker Editor enables e Managing and organizing your tracks cases and mixes on Pacemaker and your computer Automatic software upgrades when on line with the Internet Uploading your mixes to the Internet Exporting your mixes to digital audio files Creating new mixes as a stand alone application Install computer software 1 Power on your Pacemaker 2 Connect Pacemak
32. s intended that this product should be used If you have purchased this product via the Pacemaker net through mail order and or via a telephone sale you must verify that this product is intended to be used in the country in which you reside WARNING Use of this product in any country other than that for which it is intended could be dangerous and could invalidate the manufacturer s or distributor s warranty Please also retain your receipt as a proof of purchase otherwise your product may be disqualified from the manufacturer s or distributor s warranty Avoid hearing damage Mind your ears Using your headphones at a high volume may damage your hearing permanently Adjust the volume of your Pacemaker to a safe level to avoid this from happening If you experience ringing in your ears lower the volume or stop using your Pacemaker Do not use while driving You need to be careful driving Using your headphones behind the wheel is not recommended and is illegal in some areas Stop listening to your Pacemaker while driving if you are distracted by the sound and cannot keep full attention on the driving Connectors Do not force a connector into a jack If the connector and the jack cannot be joined without force they do not match Make sure that the connector and the jack matches and control that the connector is positioned correctly in relation to the jack Battery Do not try to remove the Pacemaker battery Pacemaker must
33. ssive channel Use your ears to identify the downbeat when necessary Monitor the beat graph to adjust tempo and phase during playback 1 5 Headphones monitoring Set the headphone monitoring to channel 1 With the P switch held down slide your finger along the crossfader to position the crossfade indicator at maximum left e Only channel 1 is heard through the phones output Set the headphone monitoring to channel 2 With the P switch held down slide your finger along the crossfader to position the crossfade indicator at maximum right e Only channel 2 is heard through the phones output Set the headphone monitoring at a blend between channel 1 and channel 2 With the P switch held down slide your finger along the crossfader to position the crossfade indicator between the channels e A blend of channel 1 and channel 2 corresponding to the crossfade indicator position is heard through the phones output You can control the visual behaviour of the headphones crossfader via the settings menu D Headphones volume control Adjust the volume level of the phones output With the P switch held down stroke along the touchpad rim clockwise or anti clockwise to increase or decrease the volume You can control the volume level of the lineout via the settings menu 7 7 Adjust track EQ and gain Adjust track EQ and gain Place your finger in the middle of the touchpad and swipe north east south or west depending on what you
34. ur finger from the touchpad stroke clockwise or anti clock wise along the rim to alter the pitch value up or down 3 When you re happy release your finger from the touchpad Key adjustments only apply to the current track Loading a new track will reset the key parameters to their default values 11 The location of the audio effects on the touchpad can be configured through the settings menu 7 11 Kill all effects Instantly deactivate and relaunch effects adjustments 1 Press kill all to instantly deactivate EQ colour and beat FX adjustments 2 Press kill all again to relaunch deactivated EQ colour and beat FX adjustments If you alter EQ colour and or beat FX parameters after pressing kill all you can no longer revert to previous EQ and FX adjustments Kill all will not affect Gain or Key adjustments 712 Reverse play Reverse playback direction With the P switch held up press play e The track playback direction is reversed e The play button is blinking e The reverse symbol is displayed at the top centre of the display Return to normal forward playback direction With the P switch held up press play e The track playback direction is returned to normal forward playback direction e The play button is lit e The play symbol is displayed at the top centre of the display 713 Set loop Set loop in point 1 With the P switch held up press rewind to set the loop in point e The rewind loop in point
35. y to the current track Loading a new track will reset the FX parameters to their default values The location of the audio effects on the touchpad can be configured via the settings menu 7 9 Adjust beat FX Available effects Pacemaker lets you add Roll Echo Reverb Trans and Delay beat effects Beat effects are adjusted through two parameters dry wet and time or size The effects are accessed at locations on the touchpad that can be configured through the settings menu by default Reverb is located at north top Roll at east and Echo at south Trans and Delay are not enabled by default but can be optionally enabled and assigned via the settings menu 10 Adjust the time size parameter for an effect 1 With the P switch held up swipe twice from centre to east on the touchpad to set Roll time to south to set Echo time or north to change the Reverb size e The current time or size value is shown on the display 2 Without releasing your finger from the touchpad stroke clockwise or anti clock wise along the rim to increase or decrease the value 3 When you re happy release your finger from the touchpad Adjust the dry wet parameter for an effect 1 With the P switch held up swipe from centre to east on the touchpad to set dry wet Roll south to set dry wet Echo or north to set dry wet Reverb e The current dry wet value is shown on the display 2 Without releasing your finger from the touchpad slide the finger
Download Pdf Manuals
Related Search