Hi-Copy DMX- 8611F User's Guide Revision 1.0
Contents
1. DMX 8611F Installation Guide Hi Copy DMX 8611F User s Guide Revision 1 0 FOR HOME OR OFFICE USE C Tested To Comply With FCC Standards DMX 8611F Installation Guide This device complies with Part 15 of the FCC Rules Operation is sub ject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received includ ing interference that may cause undesired operation Federal Communications Commission FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is en couraged to try to correct the interference by one or more of the following measures Od Reorient or relocate the receiving antenna Od Increase the separation between the equipment and the receiver o Connect the equipment to an outlet on a circuit d2. ce Set jumpers on them to correct positions 3 Specifications Humidity 20 80 Operating temperature 5 C 35 C Regulation FCC CE DMX 8611F Installation Guide 4 Easy Setup Open the case 1 Release the screw on the back plane 2 Remove top cover by sliding it toward backplane Remove the front door Secure CD ROM and CD R or CD R W drives with at tached screws and accessories DMX 8611F Installation Guide 1 Install DMX 8611F controller inside the case seat it properly on the bottom of the case 2 Connect IDE cable from DMX 8611F controller to both CD ROM and CD R CD R W drives 3 Attach power connectors to all devices and finally slide CD de vices into the case carefully 4 Configure CD ROM as master device and CD R CD RW as slave device Set jumpers on both devices to correct positions CD ROM MASTER CD R SLAVE Replace and fasten the front panel and the top cover DMX 8611F Installation Guide 5 Front Panel Hi Copy ott eo af S st There are three push buttons and three LED s on the front panel Their functions are Mode This key has to work with Run and Speed keys to enter special function modes Mode Run Upgrade controller firmware Mode Speed Erase CD RW content Press and halt Mode key then press Run or Speed key Re lease Run or Speed key and finally
3. ifferent from that to which the receiver is connected o Consult the dealer or an experienced radio TV technician for help Warning To meet FCC requirements a shielded power cord is required in order to prevent interference It is essential that only the supplied power cord is to be used Use only shielded cables to connect I O devices to this equipment You are cautioned that changes or modifications not approved by the party respon sible for compliance could void your authority to operate the equipment DMX 8611F Installation Guide Welcome to the DMX 8611F Installation Guide Thank you for your purchasing of DMX 8611F CD duplicator controller DMX 8611F features very easy operation with three LED s on front panel to inform you the operating result DMX 8611F uses IDE interface it must connect with one IDE CD ROM and another IDE CD R or CD R W drive to finish its job 1 Features 7 Fully stand alone CD duplicator device kS Simple and powerful operation 2e KS Single button operation IDE bus interface Fast copy kS 2e KO re Upgradeable to future devices by a CD driver K2 2e KS Auto format detection Continuous copying without waiting for cooling down 2 Note Before you start please make sure your source CD is clean kS and does not have any scratch on its surface Configure CD ROM as master device and CD R CD RW as slave devi
4. release Mode key Speed The duplication will perform a speed test first It will try the maximum speed 4x speeds and finally 2x speeds Once a speed test passes it will use that speed to perform the duplication Run This is the default setting of using maximun speed to duplicate CD 6 Update Firmware There are many new models and faster speed CD R or CD RW coming to the market everyday In order to provide the best service DMX 8611F allows user to upgrade firmware privately User can download new firmware from www domex com tw then use a PC with CD R drive to write it on a CD R put this CD R into 4 DMX 8611F Installation Guide CD ROM drive of DMX 8611F and press Mode and Run keys together to upgrade the firmware During the process please do not turn off power of DMX 8611F otherwise damage might happen 7 Operation for quick duplication 5 1 Power on and wait for 4 5 seconds to warm up 5 2 Open doors of both CD ROM and CD R drives 5 3 Put source CD into CD ROM drive 5 4 Put blank CD into CD R drive 5 5 Close doors of both drives 5 6 In general if source CD is in good condition just press Run key to perform maximun speed duplication or Press Speed key to perform secure duplication It will start speed test from the maximum speed 4x speeds then going down to 2x speeds If a speed meets the requirement it
5. t then three LEDs on the front panel will light at this moment you can let PC to take control Change CD ROM or CD RW devices back to normal DMX 8611F operation is also very easy just power down DMX 8611F then power on again DMX 8611F is in its normal operating mode 10 Technical Support Welcome to our web site http www domex com tw E mail address tec domex com tw
6. will use that speed to perform the duplication 8 Operation Step by Step Warming up Green orange and red LED s One long beep sounds red flash 5 seconds LED lights One short beep sounds green LEDlights DMX 8611F Installation Guide Copy Mode Open doors of CD ROM and One long beep sounds Put source CD into CD ROM then put blank CD into CD R close the doors of CD ROM and CD R Press Run key to have default copy or press Speed key to have secure copy During copy LED on panels If OK one short beep sounds Update firmware Mode Put update CD into CD ROM One long beep sounds Press Mode and Run keys red LED lights together then release them Finish update one short beep sounds all LED s will be off Please turn off the power then power on again DMX 8611F Installation Guide 9 1394 connection with PC In order to save hardware investment on drives of CD ROM and CD RW DMX 8611F allows user to change these two devices to become external devices of a PC Through a 1394 connection PC can easily control these two devices as external 1394 devices PC must have 1394 host controller inside together with 1394 Windows driver installed Connect one end of 1394 cable to PC s 1394 port and another end to backplane of DMX 8611F which also has two 1394 ports there connect to either one will do Power on DMX 8611F press and halt GO key for a period of 5 seconds release i
Download Pdf Manuals
Related Search