User Guide - Justec Networks
Contents
1. LED indicators for simple diagnostics and management Plug and Play Specifications Standard IEEE802 3 10Base T Ethernet IEEE802 3u 100Base TX Fast Ethernet Network Media 100Base TX UTP STP category 5 cable 10Base T UTP STP category 3 or 5 cable Connector STP RJ 45 port for 10 100Mbps TX LED indicators System Power LED Individual port link activity LEDs SPORT 8PORT NWAY SWITCH Dimension 131mm L x 71mm W x 28mm H Temperature Operating 0 C to 50 C Storage 20 C to 70 C Humidity Operating 10 to 90 RH Storage 5 to 90 RH Input Power Requirement 120VAC 60Hz Registrations FCC Part 15 Class A CE Chapter 2 Hardware Description This section describes the hardware features of the 5 8 Port Switch familiarize yourself with its display indicators and ports Front panel illustrations in this chapter display the unit LED indicators Before connecting any network device to the Switch read this chapter carefully m Front Panel The unit front panel provides a simple interface monitoring the Switch It includes a power led and 5 8 led indicator for each port m LED indicators LED Function Color Description PWR Green Lit Power on LNK ACT Green Lit Indicates the adapter is connected to switch Flash Indicates data in or put the port SPORT SPORT NWAY SWITCH m Rear Panel The rear panel of the 5 8 Port2. SPORT 8PORT NWAY SWITCH User Guide SPORT 8PORT NWAY SWITCH FCC STATEMENT Every 10 100 Switch has been tested and complies with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used according to the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which is found by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment or devices 3 Connect the equipment to an outlet other than the receiver 4 Consult a dealer or an experienced radio TV technician for assistance SPORT 8PORT NWAY SWITCH Chapter 1 Introduction This newly redesigned 5Port and 8Port 10 100 Switch can significantly increase your network traffic speed A switch serves the same function as a hub in a network design tying your network equipment together But unlike a simple minded hub which divides the network s bandwidth among all the attached devic
3. Switch indicates 5 8 RJ 45 PORT Figure of 5 8 Port Smart Switch rear panel m Side Panel The side panel of the 5 8Port Switch indicates a DC inlet which accepts 100 240V 50 60Hz Power adapter i SPORT 8PORT NWAY SWITCH Chapter 3 Hardware Installation Place the Switch on a smooth surface Connect the output of power cord to the DC inlet of the Switch Connect other IEEE802 3 compatible network device Hub Switch PC to one port of the Switch using Category 3 4 5 UTP STP cabling Connect another IEEE802 3 compatible network device Hub Switch PC to another port of the Switch by following the same process as described in Step3 Notice The cable distance between the Switch and other IEEE802 3 compatible network device should not exceed 100 meter Make sure the wiring is correct It can be used Category 3 4 5 cable in 10 Mbps operation To reliably operate your network at 100Mbps you must use an Unshielded shielded Twisted Pair UTP STP Category 5 cable or better Data Grade cabling While a Category 3 or 4 cable may initially seem to work it will soon cause data loss All kinds of IEEE802 3 compatible network device Hub Switch PC can connect to the Switch by using straight through wires or crossover wires because of Switch s auto MDIX function SPORT 8PORT NWAY SWITCH Chapter 4 Hardware Troubleshooting This chapter contains information to help you solve prob
4. es a switch delivers full network speeds at each port Installing this cost effective 5Port and 8Port 10 100 Switch can potentially increase your network speed by five eight times It s the perfect way of integrating 10Mbps Ethernet and 100Mbps Fast Ethernet devices too All ports are auto speed negotiating and have automatic MDI MDI X crossover detection so you don t have to worry about the cable type Each port independently negotiates for best speed and half or full duplex mode for up to 200Mbps of bandwidth per port Fast store and forward switching prevents damaged packets from being passed on into the network The new ultra compact case design is sure to fit into your workgroup environment Let the 5 8Port 10 100 Switch kick your 10 100 network into high gear Features Complies with the IEEE802 3 10Base T Ethernet IEEE802 3u 100Base TX SPORT 8PORT NWAY SWITCH 5 8 ports 10 100Mbps TX Auto Negotiation Ethernet Switch Full Half Duplex capability on every TX port Supports TP interface Auto MDIX function for auto TX RX swap Automatic Source MAC Address Learning and Aging Supports Store amp Forward architecture and performs forwarding and filtering Broadcast Storming Filter function IEEE802 3x flow control for Full duplex Back Pressure function for Half duplex operation Runt and CRC Filtering eliminates erroneous packets to optimize the network bandwidth Support to handle up to 1522 bytes packet
5. lems Ifthe Switch is not functioning properly make sure the Switch was set up according to instructions in this manual 1 The Power LED is not lit Solution a Check if the AC power cord is well connected Try to unplug and plug back the power cord to the LAN Switch or try another power cord b Check if the AC power source is in good condition 2 The Link LED is not lit Solution a Make sure the Switch configuration is consistent with the connecting device b Check the cable connections c Make sure the cable distance between the Switch and other IEEE802 3 compatible network device should not exceed 100 meter 3 Performance is bad Solution a Check the full duplex status of the SPORT 8PORT NWAY SWITCH Ethernet Switching If the Ethernet Switching is set to full duplex and the partner is set to half duplex then the performance will be poor Make sure the cable between the switch and other IEEE802 3 compatible network device is Category 5 UTP at 100Mbps operation 4 Some stations can not talk to other stations located on the other port Solution a b Check status of the Link LED to make sure the link is correct Make sure that the workstation s network configuration is correct modify the network configuration of workstation if need Please reset the switch if need Ce X
Download Pdf Manuals
Related Search