lamid® hdsn-30 heavy-duty soft-down stay installation manual
Contents
1. For improvement the specification may be changed without notice As for details please verify the actual goods The applicable door must have the construction for which it is difficult to induce bent or torsion Cautions for operation Keep a door from forced opening and closing It is prohibited to open a door over a full open angle or to close a door with excess force The working temperature range of this mechanism is 5 35 C Opening and closing speed of the door depends on the temperature This is not the symptom of troubles It is prohibited to use this mechanism at the temperature exceeding the specified range It is not permitted to apply this mechanism for the cabinet installing a heat generating microwave oven or other similar appliances Be careful not to insert a finger into the arm mechanism of the unit Sever injury may be caused It is necessary to periodically check the fixing screws for loosing Tighten the loosed screws as required H Part description A HDSN 30 body right hand side 1pe 1 HDSN 30 body left hand side ipe ae 5 2 Body mounting plate 1pc 3 Bind tapping screw 2 Body mounting plate 1pc 3 Bind tapping screw 5 3 5x15 3pes 3 5x15 3pes x COS m KON Tt Parts of separate packing Select either Parts for installing to 45mm width Option Parts for installing to 20mm width aluminum frame door Option aluminum frame coor or solid wooden coor BY gt 7 E ixi Od Or Om S e2. LAMB HDSN 30 HEAVY DUTY SOFT DOWN STAY INSTALLATION MANUAL PAT P Read this manual carefully for proper installation and operation Incorrect installation and improper use of the product may cause damage to the unit and also cause injury This manual should be kept by the user after installation Lapcon mount on series iP Lapcon is an innovative technology developed and designed for ultimate shock absorption Lacon and the smoothest opening and closing movement imaginable A CAUTION Any failure to observe the following cautions may result in personal injury and property damage Cautions for installation The right hand and left hand side bodies of this mechanism should be installed in set This is the mechanism exclusively for a flap type door application Be reminded that we can not take the responsibility for damages and injuries caused by other applications disassembly conversion and the application to the door exceeding the standard ranges shown in the item Type selection meth od This mechanism must be installed to the cabinet correctly in accordance with the indications of this manual Notice that the non observance of the specified dimensions not only does not enable this mechanism to show its full performance but also may result in damage and also cause injury It is necessary to use the attached screws for installing this mechanism Otherwise the disconnection of this mechanism may happen causing injury
3. ately late Truss screw M4x6 Fig 10 mee Fig 5 Fig 6 Before installing the unit mount the slide hinge to the specified position and adjust it so that the door can be opened and closed smoothly A The position adjustment of the slide hinge should be carried out before installing the HOSN SZ or HDSN AZ mounting plate Otherwise the stay arm may be deflected right or left as shown in Fig 6 which may result in trouble or damage Step 3 Put the hole of the HDSN 30 side body to the axis of the body mounting Step 1 Place the mounting plate to the specified position of the inside surface of plate insert the unit body up to the root of the plate making click a cabinet and fix it with the attached bind tapping screws 3 5x15 firmly Step 2 in case of HDSN SZ mountin plate for 45mm width A Never use a hammer or others like it in order to insert the mounting plate aluminum frame door or solid wooden door into the HDSN 30 body Otherwise trouble or damage may happen Temporarily fix the HDSN SZ mounting plate through its oblong hole to the specified position of the back of the door with the attached bind tapping screws Step 4 Adjusting the axis of the HDSN SZ mounting plate and the hole in the 3 5x15 arm end insert the truss screw M4x6 In case the HDSN AZ mounting plate for 20mm width aluminum frame door Step 5 Check the door opening and closing function and adjust the position
4. e dimensions in case of the 80 opening door are shown in This drawing shows the case of installation to 45mm width aluminum frame door or solid wooden door HDSN SZ As for the case of installation to 20mm width aluminum frame door HDSN AZ refer to Fig 7 and 8 Hinge center for slide hinge dimension standard plane 115 124 5 gt 1 Side board pect ae B from the door C 1 4mm rE side end plane a fat Glass EP g 4 j f Ly Aluminum frame T CN Fig 8 15 5 rom the door inside plana A 134 D _ No Wi Fig 7 B 15 To 5 C Distance from the side board inside surface Rubber gasket thickness D 3 5 is recommended to the aluminum frame side surface Wo Cabinet overall width To Cabinet side board thickness i Z W Door width Fig 3 S Overlay BINSTALLATION PROCEDURE This shows the installation procedure for the application of 45mm width aluminum frame door or solid wooden door HDSN SZ In case of the installation procedure for the application of 20mm width aluminum frame door HDSN AZ refer to Fig 9 and 10 Tuss screw W865 Bind tapping screw 3x15 Step 6 Oolong hole for temporary iking HDSN 20 body y Side board Bind tapping screw 3 8x15 ro 1 Body mounting Screws for fixing the mounting plate Tighten 4 screws of Step 2 and Step 7 7 Prepare separ
5. of the The fixing screws are o supplied Prepare them separately M3 5 4 is HDSN SZ mounting plate through its oblong hole recommended Fix the HDSN AZ mounting plate with the prepared fixing Step 6 Remove the arm from the mounting plate Then fix the plate firmly with the screws firmly Fig 7 and 9 bind tapping screw into its circular hole X The HDSN AZ mounting plate should be mounted so that the distance C between the side board inside surface and the aluminum frame side surface be Step 7 Insert the arm into the axis of the mounting plate again and fix the arm firmly in the range of 1 4mm Fig 8 with the truss screw M4x6 Fig 10 For Overseas Customers For North American Customers 8 SUGATSUNE SUGATSUNE KOGYO CO LTD SUGATSUNE AMERICA INC a E 1 8 11 HigashiKanda Chiyoda ku 221 East Selandia Lane Tokyo 101 8633 Japan Carson CA 90746 U S A TEL 81 3 3866 2260 FAX 81 3 3866 4447 TEL 1 310 329 6373 FAX 1 310 329 0819 http www sugatsune co jp TOLL FREE 800 562 5267 from U S A amp Canada only E mail export sugatsune co jp http Avww sugatsune com 1S09001 JSAQ384 15014001 JSAE597 CERTIFICAT E mail sales sugatsune com 12 2004 SE PRINTED IN JAPAN 0255 1
6. t jaar included f Prepare 2 pes of screw HDSN SZ mounting Truss screw M4x6 Bind tapping screw HOSN AZ mounting Truss screw M4x6 separately M3 5 4 is recommended 1 plate ipe ipe 3 5x15 4pes plate 1pc ipe ee ee j Fig 1 Part description Calculate the door torque according to the following formula considering the weight and the height of the applicable door Select the suitable type as per Table 1 Door height m 2 x Door weight kg x 9 8 Door torque N_m H Type selection method Table 1 Type and suitable door range Door torque Type 5 gt Opening angle 90 Opening angle 80 HDSN 30K 13 7 17 5 N m 140 189 kgf om 13 7 19 5N m 140 199 kgf om HDSN 30M 17 6 21 5 N m 190 229 kgf om 19 6 24 4N m 200 249 kgf om HDSN 30H 21 6 25 4N m 230 269 kgf om 24 5 29 9N m 250 299 kgf cm HDSN 308 25 5 29 4 N m 270 300 kgf om 29 4 34 3 N m 300 350 kgf om X Contact our sales representatives in case of installing to a cabinet exceeding the indicated ranges K Fig 2 Cabinet The slide hinge overlay use non catch type should be used as a door hanging device The LAMP brand 220 series slide hinge product No 220 26 19T non catch type is recommended LAMP SUGATSUNE MOUNTING DIMENSIONS E The dimensions in case of the 90 opening door are shown in the following figures Th
Download Pdf Manuals
Related Search