EX-93262/EX-93562/EX-93762 Panel PC User Manual
Contents
1. NOTE older the touch screen is the more Advanced Mode calibration points you need for an accurate calibration Use a stylus during Advanced Calibration for greater accuracy 93262 93562 93762 User Manual 28 IEJ Pen ount Control Panel d u Plot Calibration Data Check this function and a touch panel linearity comparison graph appears vyhen you have finished Advanced Calibration The blue lines show linearity before calibration and black lines show linearity after calibration 93262 93562 93762 User Manual 29 PenMount Control Panel E Gjej Calibrate Draw Option About Advanced Mode Ja Standard Calibration Dravv Tests or demonstrates the PenMount touch screen operation The display shows touch location Click to start PenMount Control Panel EX 93262 93562 93762 User Manual 30 Touch the screen vvith your finger or a stylus and the dravving screen vvill register touch activity such as left right up down pen up and pen down Click Clear Screen to clear the drawing EX 93262 93562 93762 User Manual 31 Option This panel function supports two modes Operation Mode and Beep Sound Mode which allow configuration for specific touch screen applications such as point of sales POS terminals Operation Mode This mode enables and disables the mouse s ability to drag on screen icons2. 13 0V to Ground DC Current per I O Pin 40 0 mA DC Current Vcc and GND Pins 300 0 mA Driver Software DOS Windows 3 11 Windows 95 98 ME Windows NT 2000 XP Linux QNX Windows CE for both X86 and SA CPUs EX 93262 93562 93762 User Manual 62
3. 4 2 Uninstall the PenMount Windows 98 ME Driver 1 Exit the PenMount monitor PM in the menu bar Add Remove Programs Properties Install Uninstall Windows Setup Startup Disk To install new program from floppy disk or CD ROM drive click Install Install The following software can be automatically removed by Windows remove a program to modify its installed components select it from the list and click Add Remove Add Remove Cancel Apply 2 From PenMount Utilities in Programs select the Uninstall utility 3 This message appears Are you sure you want to completely remove PenMount Utilities and all its components 4 Select Yes to remove the PenMount Windows 98 ME driver 5 Reboot system and the PenMount Windows 98 ME driver is removed from system 93262 93562 93762 User Manual 36 4 3 Windows 20001 XP Driver Installation for 9036 Control Board Before installing the Windows 2000 XP driver software you must have the Windows 2000 XP system installed and running on your computer You must also have the 9036 PenMount Serial Interface controller board installed Contents of the PenMount Windows 2000 XP driver folder are listed below DMC9000 inf DMC9000 sys DMC9000 cat SETUP EXE If you an older version of the PenMount Windows 2000 XP driver installed in your system please remove it first Follow the steps below to inst
4. brit alls ied Wizard Completed The Wired hee successfully an EC Fires to er the We recummend vou tn rebook vour compuber in erabia q the Functions 40 4 4 Configuring the PenMount Windows 2000 Driver Upon rebooting the computer automatically finds the new 9036 controller board The touch screen is connected but not calibrated Follow the procedures below to carry out calibration 1 After installation click the PenMount Monitor icon PM in the menu bar 2 When the PenMount Control Panel appears click Calibrate PenMount Control Panel The functions of the PenMount Control Panel are Calibrate Draw Multiple Monitors Option and About which are explained in the following sections Calibrate This function offers two ways to calibrate your touch screen Standard Calibration adjusts most touch screens Advanced Calibration adjusts aging touch screens standard Calibration Click this button and arrows appear pointing to red squares Use your finger or stylus to touch the red squares in sequence After the fifth red point calibration is complete To skip press ESC Advanced Calibration Advanced Calibration uses 4 9 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens Click this button and touch the red squares in sequence with a stylus To skip press ESC C IPenMount Control Pan
5. screen appears choose Yes want to restart computer now and Setup has finished copying files to your computer Before you can use the program you must restart your computer Choose one of the following options and click to finish setup Configuring the PenMount Windows 98 Me Driver Upon restarting the computer automatically finds the new 9000 controller board The touch screen is connected but not calibrated Follow the procedures below to carry out calibration 1 After installation click the PenMount Monitor icon PM in the menu bar 2 When the PenMount Control Panel appears click Calibrate PenMount Control Panel The functions of the PenMount Control Panel are explained in the following sections Calibrate This function offers two ways to calibrate your touch screen Standard Calibration adjusts most touch screens Advanced Calibration adjusts aging touch screens Standard Calibration Click this button and arrows appear pointing to red squares Use your finger or stylus to touch the red squares in sequence After the fifth red point calibration is complete To skip press ESC Advanced Calibration Advanced Calibration uses 4 9 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens Click this button and touch the red squares in sequence with a stylus To skip press ESC EX 93262 93562 93762 User Manual 27 1 JI shkrate
6. Windows 2000 XP Driver 41 4 5 Uninstall PenMount Windows 2000 XP 51 Chapter 5 Software Functions amp Descriptions 5 1 Software 2 52 5 2 Software Function 53 Appendix A Board Description amp 60 Appendix Controller IC 4 62 Figures _ Figure 1 12 DIMENSIONS e gegen gdo 8 FIGUR 1 2 BIOGK an 9 VICW ngj e onu 13 AN OU ed cato a d Ludi ded ies 14 I gure 2 1 Panelmourntilt uou no 18 FOUG 2 2 RACKMOUNIMO sna 18 Figure 3 1 Birdeye s 19 Figure 3 2 Mechanical 19 93262 93562 93762 User Manual 4 Chapter 1 1 1 Features EX 93262 12 1 SVGA 800x600 display 262K colors 300 cdim2 luminance vievving angle of 120 H 95 EX 93562 15 SVGA 1024 768 display 16 2M colors 400 cdim2 luminance viewing angle of 170 H 135 Vj EX 93762 17 SVGA 1280x1024 display 16 2M colors 300 cd m2 lumina
7. Windows 95 Windows 98 ME Windows 2000 XP as well as Windows 98 USB and Windows Me 2000 XP support display rotating software packages such as e Portraits Pivot Screen Rotation Software e ATI Display Driver Rotating Function e nVidia Display Driver Rotating Function e SMI Display Driver Rotating Function e Intel 845G GE Display Driver Rotating Function Configuring the Rotation Function 1 Install the rotation software package 2 Choose the rotating function 0 90 180 270 in the 3 party software calibration screen appears automatically Touch this point and rotation is mapped Please touch tha paint NOTE The rotating function is disabled if you use Monitor Mapping EX 93262 93562 93762 User Manual 50 4 5 Uninstall the PenMount Windows 2000 XP Driver 1 Exit the PenMount monitor PM in the menu bar 2 Goto Settings then Control Panel and then click Add Remove program Select PenMount DMC9000 and click the Add Remove button GOJ PELLI RI hi aded m qo Pn Para OC HDI mot SE LI Lee 5 eh beer Or ner i locam gere iem eee cick RS an LE xg DP t ES GE 4 Select Yes and Close to remove the PenMount Windows 20001XP driver and reboot the system EX 93262 93562 93762 User Manual 5 C
8. the Matrox nVidia ATI etc or that outputs into a 1 into 2 VGA signal box Two or more touch screens Two or more serial ports or USB ports Two or more PenMount 9000 control boards such as the 9036 9026 9084 or 90A4 or PenMount 5000 control boards such as the 5184 or 51A5 If using the PenMount 9000 control board the driver must be the PenMount 9000 Windows 2000 XP v4 01 or greater software driver If using the PenMount 5000 control board the driver must be for Windows 98 ME 2000 XP CE 9000 Control Boards To use multiple devices with 9000 Control Boards 1 Configure your computer hardware 2 Attach each 9000 Control Board to a different computer s serial port 3 4 Use each driver s Calibration function to calibrate each computer s touch screen Install the appropriate PenMount software driver in each computer You must calibrate each touch screen before configuration is complete Rotation There are currently a number of software packages on the market that support rotating monitors O 90 180 and 270 However you will not be able to use a touch screen unless it is matched to the appropriate rotation Our rotation configuration function allows you to easily match the touch screen when you rotate your monitor If you use a rotating monitor you will need a display card such as from nVidia Intel SMI or ATI and software such as Portrait Pivot Pro For software operation and features please refer to your soft
9. useful for configuring POS terminals Stream Mode Select this mode and the mouse functions as normal and allows dragging of icons Point Mode Select this mode and the mouse only provides a click function and dragging is disabled Beep Sound Mode Enable Beep Sound turns beep function on and off Beep on Pen Down beep occurs when pen comes down Beep on Pen Up beep occurs when pen is lifted up Beep on both of Pen Down Up beep occurs on both Beep Frequency modifies sound frequency Beep Duration modifies sound duration PenMount Control Fanel E E Iri xi Calibrate Draw Option About Operation Mode Enable on P r Down Beepion Pen on Bath 93262 93562 93762 User Manual 22 About This panel displays information about the PenMount controller and this driver version PenMount Control Panel Calibrate Draw Option About Driver Version 3 2 00 Application version 3 2 00 Support Chips DMCY00 Firmware Version Az 00 Please contact Salt International Corp if you have any questions E mail com tw website www zall corn PenMount Monitor Menu The PenMount monitor icon appears in the menu bar of VVindovvs 98 system when you turn on the PenMount Monitor in the PenMount Utilities K 10 07 AM The PenMount Monitor has the follovving functions
10. 4 Mount your touch screen to the display 5 Find the onboard DIP switch on the upper right of the image above see Figure 3 1 This switch selects baud rate PnP or non PnP mode and touch screen type Set the DIP switch to configure your control board according to the definitions and settings of the table below SI Rate Adjustment 9600 19200 6 Turn on power to the computer and the display T nstall the software drivers and utilities and calibrate the touch screen 93262 93562 93762 User Manual 21 Chapter 4 4 1 Windows 98 ME Driver Installation for 9036 Controller Board Before installing the Windows 98 ME driver software you must have the Windows 98 ME system installed and running on your computer You must also have the 9036 PenMount Serial Interface controller board installed Contents of the PenMount Windows 98 ME driver folder are listed below SETUP EXE DMC9000 INF DMC9000 VXD If you have an older version of the PenMount Windows 98 ME driver installed in your system please remove it first Follow the steps below to install the PenMount Windows 98 Me driver 1 When the system first detects the controller board a screen appears that shows Unknown Device Do not use this hardware wizard Press Cancel Add New Hardware Wizard E E ETE MR T Vul would vou like do C Specity the locaton of the diver Advanced 93262 93562 93762 User Manual 22 2 Install the PenMount VVind
11. Control Panel Right Click Button Beep Sound Enable Exit EX 93262 93562 93762 User Manual 33 Right Click Button When you select this function mouse icon appears in the right bottom of the screen Click this icon to switch between Right and Left Button functions Beep Sound Turns beep on or off Enable PNP Turns PNP on or off When this is unchecked PNP is off The RS 232 transfer signal is continuous when the cable is unplugged and plugged into the serial port Exit Exits the PenMount Monitor function PenMount Rotating Functions The PenMount driver for Windows 98 ME supports several display rotating software packages The PenMount drivers for Windows 95 Windows 98 ME Windows 2000 XP as well as Windows 98 USB and Windows ME 2000 XP support display rotating software packages such as e Portraits Pivot Screen Rotation Software ATI Display Driver Rotate Function e nVidia Display Driver Rotate Function e SMI Display Driver Rotate Function e Intel 845G GE Display Driver Rotate Function EX 93262 93562 93762 User Manual 34 Configuring the Rotation Function 1 Install the rotation software package 2 Choose the rotating function 0 90 180 270 in the 3 party software The calibration screen appears automatically Touch this point and rotation is mapped Please touch the paint NOTE The Rotating function is disabled if you use Monitor Mapping EX 93262 93562 93762 User Manual 35
12. EX 93262 EX 93562 EX 93762 Panel PC User Manual Release Date Revision June 2005 V0 1 92005 All Rights Reserved Published in Taiwan 93262 93562 93762 User Manual Warning This equipment generates uses and can radiate radio frequency energy and if not installed and Used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules which are designed to provide reasonable protection against such interference when Operated in a commercial environment Operation of this equipment in a residential area is likely To cause interference in which case the user at his own expense will be required to take whatever Measures may be required to correct the interference Electric Shock Hazard Do not operate the workstation with its back cover removed There are dangerous high voltages inside Disclaimer This information in this document is subject to change without notice EX 93262 93562 93762 User Manual 2 Table of Contents MV ANPING ses e 2 ss 2 Chapter 1 Gettina Started E 5 1 2 as on e 5 IMC SIONS T 8 14 BIOCK OT AI se g ere ba an e 9 1 5 471 Celeron M CPU 4 10 1 0 Sa
13. Support Map Touch Screens 2 When the mapping screen message appears click OK PenMount Control Panel la Eg Calibrate Craw Multiple Monitors Option About Enable Multiple Monitor Support EX 93262 93562 93762 User Manual 46 3 4 NOTES Touch each screen as it displays Please touch this monitor Following this sequence and touching each screen is called mapping the touch screens Touching all screens completes the mapping and the desktop reappears on the monitors Select a display and execute the Calibration function A message to start calibration appears Click OK Calibrate To start calibration please touch Ehe panel to calibrate in the Following screen Touch this screen to start its calibration appears on one of the screens Touch the screen Touch the red square messages appear Touch the red squares in sequence Continue calibration for each monitor by clicking Standard Calibration and touching the red squares 1 If you use a single VGA output for multiple monitors please do not use the Multiple Monitor function Just follow the regular procedure for calibration on each of your desktop monitors 2 The Rotating function is disabled if you use the Multiple Monitor function 3 If you change the resolution of display or screen addre
14. Touch the screen with your finger or a stylus and the drawing screen will register touch activity such as left right up down pen up and pen down EX 93262 93562 93762 User Manual 44 Click Clear Screen to clear the drawing Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system The PenMount drivers for Windows 2000 XP support Multiple Monitors This function supports from two to six touch screen displays for one system Each monitor requires its own PenMount touch screen control board either installed inside the display or in a central unit The PenMount control boards must be connected to the computer COM ports via the RS 232 interface Driver installation procedures are the same as for a single monitor Multiple Monitors support the following modes Windows Extends Monitor Function Matrox DualHead Multi Screen Function nVidia nView Function NOTE The Multiple Monitor function is for use with multiple displays only Do not use this function if you have only one touch screen display Please note once you turn on this function the rotating function is disabled EX 93262 93562 93762 User Manual 45 Enable the multiple display function as follows 1 Check the Enable Multiple Monitor Support box then click Map Touch Screens to assign touch controllers to displays PenMount Control Panel Miles Calibrate Draw Multiple Monitors Option About Enable Multiple Monitor
15. Under normal circumstances otandard Calibration is all you need to perform an accurate calibration Advanced Calibration The Advanced Calibration function improves the accuracy of calibration by using more involved engineering calculations Use this function only if you have tried the Standard Calibration and there is still a discrepancy in the way the touch screen maps to the display You can choose 4 9 16 or 25 points to calibrate though we suggest that you first try 9 points if it is still not tracking well then try 16 or 25 points The more points you use for calibration the greater the accuracy Errors in calibration may occur due to viewing angle or individual skill and there may be little difference in using 16 or 25 points Note that a stylus is recommended for the most accurate results Multiple Monitors Until now most touch screen systems only support one monitor and users of multiple monitors have not been able to use touch screen systems This situation has inspired PenMount to design and develop Multiple Monitors support using the PenMount 9036 control board and Windows 2000 XP driver Our advanced design supports from 2 to 6 monitors that can be split horizontally or vertically Requirements Before using the Multiple Monitor function you need the following 1 Adisplay card that supports multiple monitors such as the Matrox nVidia ATI etc Two or more display cards supported by Windows are also OK 2 Two or mor
16. all the PenMount Windows 2000 XP driver 1 When the system first detects the controller board a screen appears that shows Unknown Device Do not use this hardware wizard Press Cancel Found Now Hardware Wizard Welcome to the Found New Hardware Wizard Tha vyer helps vou toe Lirit Mun came mih an al 2 Hoppe disk met now ma md In da at the oftware Sonata s Flecommended rore ac specie beson Gr conira Hed gt i EX 93262 93562 93762 User Manual 37 2 Insert the PenMount Driver CD ROM Go to the Windows 2000 XP Driver folder Click setup exe Welcome to th InstalShieti for Penfsicunt OMCS000 and 09029100 The Aired retell Pence and DNCOEUC on your To contrast cick Next EX 93262 93562 93762 User Manual 38 3 License Agreement appears Click I accept and Next 2 Peniaunt 9000 and DiKCS TOO Wizard Llirense Agreement ped Ue agreement care Soden License Copyright C Sait Intemational Corp AT right reserved divers DOS Windows 211 Windows 25 Wewa T Windows Windows HT Windows 2000 VWadaus XP liro CE Lax asi drivers copy modiy probabried except with writan comments To boense P
17. cations Touch Screen 4 5 and 8 wire analog resistive type Touch Screen Controller DMC9000 Communications RS 232 Baud Rate 19200 and 9600 baud rate selection Resolution 1024x1024 10 bit A D converter inside Power Input oV 12V DC Power Consumption 12V 24 i where i v touch screen sheet R oV 20 i where i v touch screen sheet R 93262 93562 93762 User Manual 20 Board Size 6 0 x 2 5cm Portrait Support 90 to 279 screen rotation Static Protection ESD device optional 3 4 Installation of the 9036 Controller Board Follow the steps below to install the 9036 control board 1 Power down your computer and display and open your display or system case Find space on your system and attach the control board to your system with screws The control board has industry standard 39 screw holes 2 Find the white 6 pin right angle connector on the left in the image above see Figure 3 1 The power cable is pin 1 and pin 2 Solder the power and ground wire to the system The RS 232 cable is for pins 3 to 6 Attach the RS 232 cable s D sub connector to a COM port at the back of the computer 3 Find the white 9 pin right angle connector on the right in the image above see Figure 3 1 Attach the female end of the touch screen cable to this connector If you attach the cable of a 4 5 8 wire touch screen to pins 1 5 1 6 1 9 attach the male end of the cable to the touch screen tail
18. e touch screens Two or more serial ports 4 Two or more PenMount 9000 control boards such as the 9036 9026 9084 or 90A4 5 PenMount 9000 Windows 2000 v4 01 or greater software driver ed Before using Multiple Monitors you must have two or more monitors that are in extension mode For display cards that support multiple monitors we suggest you consider Matrox 93262 93562 93762 User Manual 53 nVidia or ATI cards and inquire about operation and usability issues Note Before you can use multiple monitors you need to map each monitor Multiple Devices The Multiple Devices function is designed to let you use two or more monitors to display the same image Software that supports this function includes the PenMount 9000 2000 XP drivers and the PenMount 5000 98 Me 2000 XP CE drivers The drivers for PenMount 9000 can support up to six control boards and the drivers for PenMount 5000 support up to 16 Comparing Functions The difference between the Multiple Monitors function and the Multiple Devices function are illustrated below The Multiple Monitors function shown above extends the screen into 2 or more monitors EX 93262 93562 93762 User Manual 54 The Multiple Devices function displays the same image two or more monitors Requirements Before using the Multiple Monitors function you need the following p A display card that supports Dual Monitors such as
19. el Mis Lalibrate Draw Multiple Monitors Option About Advanced E Plat calibration data Standard Calibration Advanced Calibration 93262 93562 93762 User Manual 41 NOTE older the touch screen is the more Advanced Mode calibration points you need for an accurate calibration Use a stylus during Advanced Calibration for greater accuracy L PenMount Control Panel Mis Lalibrate Draw Multiple Monitors Option About Advanced Made Plot calibration data Advanced Calibration EX 93262 93562 93762 User Manual 42 Plot Calibration Data Check this function and a touch panel linearity comparison graph appears vyhen you have finished Advanced Calibration The blue lines show linearity before calibration and black lines show linearity after calibration PenMount Control Panel 9 Lalibrate Draw Multiple Monitors Option About Advanced calibration data Standard Calibration EX 93262 93562 93762 User Manual 43 Dravv Tests demonstrates the PenMount touch screen operation The display shows touch location Click Draw to start Touch the screen with your finger or a stylus and the drawing screen will register touch activity such as left right up down pen up and pen down E PenMount Control Panel Miles Calibrate Draw Multiple Option About
20. enbdaunt Libres divzess contact Sak EInteenatinnal Cop zl pags com bw the beri in the not accept the teme in the sgeui 4 The Ready to Install the Program screen appears Select Install P penilaumt 9000 and 9100 InstallShield Wizard Ready En Install the Program EX 93262 93562 93762 User Manual The sazard E ready to reiallabon Click petsto begin the installation T you sank bo rere or change ans of pour installation settings cick Back bo the 39 5 The next screen is Hardware Installation Select Continue Anyway Hardware Installation The software you are installing For this hardware Fen ount 000 and 00 has not passed Windows Logo testing to verify its compatibility with Windows Tell me why this testing important Continuing your installation of this software may impair destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation 6 The InstallShield Wizard Completed appears Click Finish EX 93262 93562 93762 User Manual
21. fety PTECAUUONS cias ea dd 13 1 7 Brief Description of EX 93202 93562 09f OZ edeme pen pdr Pri 13 Chapter 2 Hardware Installation 2 Installation of 93262 93562 93762 15 2 1 Removal of Chassis 15 2 2 HDD BTACKO me oe 15 2 9 Connecting Cable tO do eina 16 24 PUNO ADI MIO BTACKO diuo dua d 16 2 9 TONIN O ribus nues enixe DIVA 16 2 0 Installing FID eode traen 17 21 Chassis COVEN Eoi 17 NOT U Ge asistentes 18 2 9 TRACK e 18 Chapter 3 Controller Board Installation 3 1 Introduction to PenMount 9036 Controller Board 20 S NOI E TITLE 20 3 3 Electrical 2 20 3 4 Installation of 9036 Controller Board 21 93262 93562 93762 User Manual 3 Chapter 4 Software Installation 4 1 Windows 98 ME Driver Installation for 9036 Controller Board 22 4 2 Uninstall PenMount Windows 98 ME Driver 36 4 3 Windows 2000 XP Driver Installation for 9036 Controller Board 31 4 4 Configuring PenMount
22. g angle of 170 H 135 V Mechanical Construction Heavy duty steel chassis NEMA 4 IP65 rated front panel panel mount Front Panel Color Beige Dimensions 93262 390 W x 102 D x 264mm H EX 93562 410 W x 106 D x 310mm H EX 93762 457 W x 114 D x 355mm H Weight EX 93262 6 45kgs 93562 7 48kgs EX 93762 8 68kgs 93262 93562 93762 User Manual Power Supply 12V 24V DC input 60W ATX PSU Environment Operating temperature 0 50 Storage temperature 10 75 C Relative humidity 10 90 40 C non condensing Vibration o 17Hz 0 1 double amplitude displacement 17 640Hz 1 5G acceleration peak to peak Shock 10G acceleration peak to peak 11 millimeters Ordering Information e EX 93262 EX 93562 EX 93762 Barebone w Celeron amp M 600MHz processor w o HDD RAM and CD ROM EX 93262 T EX 93562 T EX 93762 T Barebone w Celeron M 600MHz processor amp resistive touch screen w o HDD RAM and CD ROM e 93262 5 93562 5 93762 5 Celeron M 600MHz processor 256MB DDR SO DIMM 40GB HDD slim combo DVD w o touch e EX 93262 ST EX 93562 ST EX 93762 ST Celeron 600MHz processor resistive touch screen 256MB DDR SO DIMM 40GB HDD slim combo DVD 93262 93562 93762 User Manual 1 3 Dimensions mm 21 Bununojn e d gt Figure 1 1 Dimens
23. hapter 5 5 1 Software Functions This chapter describes the special software functions that configure and adjust the PenMount controller board and touch screen hardware Please note that not all of the functions are available for every driver Software functions and their availability for specific interface and systems are shown in the table below a description for each function follows Software Function 005 Win 3 1 95 98 Me 2000 XP CE Linux QNX standard Calibration e e ej em Advanced Calibration em en Multiple Monitors Multi Device E e m Rotation em e Stream Point mode on e Drawing mode e e e Sound e e e Beep sound adjustable on e Wake up function em Showing linearity Right button e e en e Hide cursor e e e e Double click area and e e speed adjustable About e 9 on e RS 232 Interface 9000 series USB Interface 5000 series EX 93262 93562 93762 User Manual 3 5 2 Software Function Description Description for each of the software functions shown in the table above follows Standard Calibration The Standard Calibration function lets you match the touch screen to your display so that the point you touch is accurately tracked on screen Standard calibration only requires four points for calibration and one point for confirmation
24. ic shock Don t touch any components of this card when the card is power on Always disconnect power when the system is not in use Disconnect power when you change any hardware devices For instance when you connect a jumper or install any cards a surge of power may damage the electronic components or the whole system 1 7 Brief Description of the EX 93262 EX 93562 and EX 93762 The EX 93262 EX 93562 and EX 93762 are rugged and compact panel mount industrial fanless PCs which come with a 12 1 inch 300 cd m2 15 inch 400 cd m2 and 17 inch 300 2 TFT LCD respectively They are powered by an Intel Celeron M processor and offer optimal heat dissipation and low power consumption without sacrifice of speed performance These industrial panel PCs also feature 2 expansion slots 4 COM ports and slim CD DVD combo drive and support 2 USB 2 0 ports They come with 12 24V DC power input They are ideal for use as a PC based controller for Automotive Logistic Process Materials Handling and Kiosk applications Figure 1 3 Front View of 93262 93562 93762 93262 93562 93762 User Manual 13 Figure 1 4 VO Layout of 93262 93562 93762 EX 93262 93562 93762 User Manual 14 Chapter 2 2 installation of 93262 93562 93762 Touch Panel Computer 2 1 Removal of Chassis Cover There are 7 screws to deal with when enclosing or removing the chassis Six are along the three sides of the chassis as show
25. ions of the EX 93262 Note Structures of EX 93562 and EX 93762 are the same as that of the 93262 shown above except for the dimensions which are 410 W by 106 D by 310mm H and 457 W by 114 D by 355mm H respectively EX 93262 93562 93762 User Manual 1 4 Block Diagram LVDS Touch ari cable Touch Screen VS Optional pJeoq Display Module Inverter cub Touch power amp Rs212 iE 1 Optional mille 9472 Slim CDRom EAD RAH Power cable ir IDE cable o e TB 2000 see 2 9 HDD Engine Box Module E E E E E E E E E E E E ee ee E Figure 1 2 Block Diagram of the EX 93262 EX 93562 EX 93762 EX 93262 93562 93762 User Manual 1 5 9472 Celeron amp CPU Card for the EX 93262 EX 93562 and EX 93762 Cosnect LIEB Connector FA 1 Connect CONI FO Connect Mini FLI Connector OO LL Connectai Conn chor Cni ini Specifications System CPU Intel Celeron M processor CPU Frequency ULV 600MHz non L2 cache Chipset Intel 852GM ICH4 DRAM One 200 pin DDR SO DIMM supporting DDR266 SDRAM up to 1GB BIOS Phoenix Award PnP BIOS with VGA BIOS Watchdog 1 255 secs wa
26. n in the picture by the arrows while one circled is on the top 2 2 Removal of HDD Bracket 1 remove the bracket from its position just unscrew the 4 screws as shown in picture EX 93262 93562 93762 User Manual 15 2 3 Connecting Cable to HDD Connect the cable to the HDD making sure that the red stripe of the cable is on the right side if connected vvith the top of the HDD facing 2 4 Putting HDD into Bracket Place the HDD into the base of the bracket as shown in the picture 2 5 Tightening HDD Tightly fasten the four screws as circled to secure the HDD EX 93262 93562 93762 User Manual 16 2 6 Installing HDD DM Get the 4 screvvs tightened onto the chassis as shown in the picture 2 7 Closing Chassis Cover To finish the job just fasten the 7 screvvs as shown in the picture EX 93262 93562 93762 User Manual 2 8 Panel Mounting The 93262 93562 93762 panel is designed to be panel mounted as shovvn in Figure 2 1 Just carefully place the unit through the hole and tighten the given 8 screws from the rear to secure the mounting Figure 2 1 Panelmounting of the EX 93262 93562 93762 2 9 Rack Mounting optional The EX 93262 93562 93762 panel can be rack mounted as an option Just carefully slide it into the rack and tighten the given 8 screws from the front to secure the mounting as shown i
27. n Figure 2 2 Figure 2 2 Rackmounting of EX 93262 93562 93762 93262 93562 93762 User Manual 18 Chapter 3 3 1 Introduction to the PenMount 9036 Controller Board The PenMount 9036 control board is configured for use with the RS 232 interface It connects to the touch screen power supply and computer system s RS 232 port and supports 4 5 and 8 wire touch screens The control board has some advanced functions such as PnP and non PnP mode adjustable baud rate thus making easy for customers to select different touch screens without changing the control board The size of the board is 25 by 60mm and it has two connectors and one dipswitch on board Figure 3 1 Bird s Eye View of PenMount 9036 60 0 3 38 3 38 25 0 BJO _ 3 48 Figure 3 2 Mechanical Dravving of PenMount 9036 93262 93562 93762 User Manual 19 3 2 Features RS 232 interface Touch controller is DMC9000 Design for the best touch performance and easy configuration PnP or Non PnP mode selectable Design for best cost arrangement Supporting 2048x2048 pen device resolution 19200 or 9600 baud rate transmission selectable Upgraded noise handling mechanism 3 level scheme Fixed and high speed sampling rate 4 5 and 8 wire touch screen supported Touch screen cable RS 232 with power cable connectors onboard oV to 12V power input Circuit protection for input voltage Touch activated LED indicator onboard 3 3 Electrical Specifi
28. nce viewing angle of 140 H 130 V Front panel NEMA 4 IP 65 rating panel mount Fanless design Low noise and low power consumption Resistive touch screen optional Ethernet 2 PCI expansion slots 2 USB 2 0 ports 4 COM ports one is reserved for touch screen opace for slim CD DVD combo drive or optional CD RW DVD DC 12 24V wide ranging input 1 2 Specifications System CPU Intel Celeron M processor with clock rate of 600 2 non L2 cache Chipset Intel 852GM ICH4 System Memory DDR266 SDRAM max 1GB DRAM Socket One 200 pin SO DIMM Hard Drive One 2 5 slim type BIOS Phoenix Award 2MB PnP BIOS IDE Interface 2 UDMA 33 66 100 EX 93262 93562 93762 User Manual CD ROM 1 x slim CD DVD Combo Drive Watchdog 1 255 sec watchdog timer with Reset and VO Port Two COM ports one SPP ECP EPP port two USB2 0 ports two PS 2 keyboard and mouse ports RJ 45 LAN Port 2 x Realtek RTL8100 10 100Mbps support Wake on LAN with ATX power VGA Built in Intel amp 852GM Expansion Slot 2 x PCI slot Touch Screen optional Resistive EMC FCC amp CE Class A certified Display EX 93262 12 1 SVGA 800x600 display 262K colors 300 cd m2 luminance viewing angle of 120 H 95 Vj EX 93562 15 SVGA 1024x768 display 16 2M colors 400 cd m2 luminance viewing angle of 170 H 135 Vj EX 93762 17 SVGA 1280x1024 display 16 2M colors 300 cd m2 luminance viewin
29. offer a fixed buzzer sound Beep Sound Adjustable Software drivers for Windows systems let the user adjust the frequency and length of the beep sound The drivers let the user adjust the desired touch screen sound as well as turn the sound off Wake Up Function The Wake Up function lets the user touch the screen and wake the system up from suspend mode Point Calibration Data The Plot Calibration Data function displays the touch screen linearity map which is available if the PenMount driver provides an Advance Calibration function when touch screens age their touch linearity declines This non linearity is apparent when the touched point on the touch screen is not the same as the point on the display The plot calibration data function shows the linearity status of the touch screen This is only a support function for the user The exact linearity of a touch screen requires a linearity test machine 93262 93562 93762 User Manual 58 Right Button The Right Button function simulates the right button function of a mouse Click the right button and the user can only touch the screen once and the driver changes the touch definition to the left button Hide Cursor The Hide Cursor function keeps the cursor arrow and other cursor symbols from appearing when using the touch screen The cursor appears when the user turns this function off Cursor Offset The Cursor Offset function lets the user adjust the position of the touch poin
30. op Sense PIN 5 Right LR Right PIN 4 Left LI Left PIN 3 Bottom UR Bottom PIN 2 Top UL Top PIN 1 Ground Ground Ground 93262 93562 93762 User Manual 60 Connector Pin Definitions for Povver and RS 232 Power Lines RS 232 Interface Pin PINI PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 Definition Ground 5 2 power RTS TXD RXD Ground 93262 93562 93762 User Manual 6l Appendix Controller Specifications This appendix offers information on touch screen controller IC features and specs PenMount DMC9000 Touch Screen Controller IC The PenMount DMC9000 is the best performance touch screen controller Designed with PnP features for new system trends it offers RS 232 touch screen interface The DMC9000 is designed for those who need an all in one solution with a built in A D converter for a denser total printed circuit board Electrical Specifications 8000 1 0 ARARRRERERETY Touch Screen 4 5 amp 8 wire Package 28 pin PDIP or 32 pin Communications RS 232 Characteristics 8 bit RISC microprocessor with built in functions including 10 bit ADC UART Timer Counter Comparator Watchdog Memory etc Voltage Range 4 0V to 6 0V Power Consumption Active 3 4 mA Idle Mode 1 4mA at 4 MHz Power Down Mode SI LA Operating Temperature 40 C to 185 C Storage Temperature 65 C to 150 C Volt on RESET with respect 1 0V to
31. ovvs 98 driver onto your system from the CD ROM penmourit SIAD bb VH Arbe normal Troe Application She T EB ME Ms Louer 3 Awelcome message for the PenMount utilities setup program appears Select Next Weir ome Hee inst wizsaed lor The bei di ht iced Does wx computer continue EX 93262 93562 93762 User Manual 23 4 The Software License Agreement screen appears Select Yes 93262 93562 93762 User Manual 24 6 The Choose Destination Location screen appears This installs PenMount Utilities in the folder C Program Files PenMount Win9x Select Next or modify the folder name to the one you would like to use _ T TC PDT Chops Destination 7 The Select Program Folder screen appears The default is PenMount Utilities Select Next or change it 93262 93562 93762 User Manual 25 8 The Start Copying Files screen appears Select Next to copy files to the system pem TUTT Shat Copying Files 9 The Setup Complete screen appears Select Finish Setup EA als hich Complete LALTIDH T fere rang bota pour PC ied nxir 93262 93562 93762 User Manual 10 Restarting Windows
32. ss you have to redo Map Touch Screens so the system understands where the displays are EX 93262 93562 93762 User Manual 47 About This panel displays information about the PenMount controller and this driver version C IPenMouni Control Panel Mis Calibrate Draw Multiple Monitors Option About PenMount DMCS000 and DRDSTUL version 4 01 Firmware version E mail com Website www salt conn 2003 Salt Corp PenMount Monitor Menu Icon The PenMount monitor icon PM appears in the menu bar of Windows 2000 XP system when you turn on the PenMount Monitor in the PenMount Utilities pm 4 04 The PenMount Monitor has the follovving functions Control Panel Right Button Pen Stabilizer Exit EX 93262 93562 93762 User Manual 48 Right Button Pen Stabilizer Exit EX 93262 93562 93762 User Manual Turns beep on or off When you select this function a mouse icon appears in the right bottom of the screen Click this icon to switch between Right and Left Button functions Check this function to reduce cursor vibration for relatively unstable touch screens or where there may be excess vibration Normally this function is not checked Exits the PenMount Monitor function 49 PenMount Rotation Functions The PenMount driver for Windows 2000 XP supports several display rotating software packages The PenMount drivers for
33. t to a desired location away from the real touch point Double Click Area and Speed The Double Click Area and Speed function lets the user adjust the double click area and speed to their personal preference About This option shows the exact version of the drivers and controller firmware Updated drivers are available for download on the PenMount website 93262 93562 93762 User Manual 59 Appendix A Board Descriptions amp Specifications This appendix provides information on controller board features and specifications PenMount 9036 Control Board The PenMount 9036 control board is configured for the RS 232 interface and it supports 4 wire 5 wire and 8 wire touch screens PenMount 9036 Features e DMCO9000 touch controller e Diagnostic LED on board e Supports PnP and non PnP mode Supports 4 wire 5 wire and 8 wire touch screen e Baud rate 19200 or 9600 bps selectable Automatic pin assignment adjustment e Input voltage is 5V to 12V e Bundled with PenMount drivers which are also available for download from our website Connector Pin Definitions Pin definitions for the two connectors on the PenMount 9036 control board follow Connector Pin Definitions for Touch Screen Pin definition 4 wire 5 wire 8 vvire I vvires touch screen touch screen touch screen PIN 9 Right Sense PIN 8 Left Sense PIN 7 Bottom Sense PIN 6 NJA Sense T
34. tchdog timer selectable w Reset NMI EX 93262 93562 93762 User Manual 10100 LAM Connecti Pari Danteska N Consan LSE Comair Tid non irj 25 ones up i 156 10 Power Supply Support ATX power Power Requirements 5 12 12V 5VSB Dimensions 170mm x 170mm 6 69 x 6 69 inches VO Ports IDE Interface One 40 pin IDE UDMA 33 66 100 CF One Compact flash slot IDE FDD Interface One FDD Bus Interface PCI slot mini PCl bus Serial Port Four COM ports COM1 and 4 for RS232 and 2 and for RS23214221485 for 16550 compatible type of UART Parallel Port One parallel SPP EPP ECP IrDA 1 SIR Keyboard Mini DIN connector Mouse Mini DIN connector LAN Realtek RTL8100C 10 100Mbps 93262 93562 93762 User Manual Support Wake on with power USB Six USB 2 0 Display Graphics Built in Intel amp 852GM sharing system memory and supporting CRT LVDS LCD Interface 18 36 bit LVDS Environment Operating Temperature 0 60 32 140 F Storage Temperature 40 85 40 185 F Operating Humidity 20 90 Storage Humidity 20 95 EX 93262 93562 93762 User Manual 12 1 6 Safety Precautions Follow the messages below to avoid your systems from damage Avoid your system from static electricity on all occasions Prevent electr
35. ware manual Configuring the rotation function is easy Select this option and a point appears for you EX 93262 93562 93762 User Manual 55 to touch Once the point is touched the software driver understands which degree you plan to rotate your display The rotation function supports 90 180 and 270 degrees rotation 0 degrees EX 93262 93562 93762 User Manual 56 EX 93262 93562 93762 User Manual 90 degrees 180 degrees 270 degrees 57 Stream Point Mode Stream and point modes control the touch and drag function of the touch screen The point mode only allows touch interaction with the screen and does not allow the user to drag objects The point mode is useful for maintaining the location of screen icons such on POS terminals The stream mode allows a user to touch and drag icons and other items around on the screen similar to using a mouse Drawing Mode Drawing mode is a utility that lets the user draw on the screen using a finger or stylus This allows the user to test the touch screen and touch controller to see if it is operational or is mapped correctly The drawing mode can display either the matrix address of points touched or just show lines drawn One of the PenMount driver s strengths is a special mathematical algorithm that minimizes the occurrence of noise and smooths the drawing of lines Beep Sound All of PenMounts drivers support the beep sound function however some PC systems may only
Download Pdf Manuals
Related Search