IPC910H Series Embedded System User's Manual
Contents
1. NOTE This function is only available with DOS and other operating systems that do not trap INT13 e CPUL1 amp L2 Cache These two options speed up memory access However it depends on the CPU chipset design The default setting is Enabled CPUs without built in internal cache will not provide the CPU Internal Cache item on the menu Enabled Enable cache Disabled Disable cache e Quick Power On Self Test This option speeds up Power on Self Test POST after you turn on the system power If set as Enabled BIOS will shorten or skip some check items during POST The default setting is Enabled Enabled Enable Quick POST Disabled Normal POST e First Second Third Boot Device These items let you select the 1 2 and 3 devices that the system will search for during its boot up sequence The wide range of selection includes Floppy L S120 ZIP100 HDDO 3 SCSI and CDROM 34 Phoenix Award BIOS Utility IPC910H Series User s Manual e Boot Other Device This item allows users to enable or disable the boot device not listed in the First Second Third boot devices option above The default setting is Enabled e Boot Up Floppy Seek During POST BIOS will determine the floppy disk drive type 40 or 80 tracks The 360Kb type is 40 tracks while 720Kb 1 2MB and 1 44MB are all 80 tracks The default value is Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks Please be noted BIOS can not differ2. 14 Hardware Installation IPC910H Series User s Manual 2 2 Installing the Memory Module Step 1 Turn off the system Step 2 Disconnect the power connector Step 3 Loosen screws to remove the side cover from the chassis ETT NUI PARA na as ma SS c o e si a r HE LIII id aa Step 4 Please follow steps below to install the memory module 1 Align the memory module with the socket that notches of memory module must match the socket keys for a correct installation J s s TF E oe fe tee P oS m om m H EL IET Hardware Installation 15 IPC910H Series User s Manual 2 Install the memory module into the socket and push it firmly down until it is fully seated The socket latches are clipped on to the edges of the SO DIMM Step 5 Put back the side cover to the chassis and fasten all screws 16 Hardware Installation IPC910H Series User s Manual 2 3 Installing the Hard Disk Drive The IPC910H Series offers a convenient drive bay module for users to install HDD The system offers users one 2 5 Hard Disk Drive for installation Please follow the steps Step 1 Turn off the system Step 2 Disconnect the power connector Step 3 Loosen screws to remove the side cover from the chassis hd ET i LIT T S855 nee ETHER p ET PEH 7 Em side Ll m mma setae eee NET amp aislada SS tee cts WIE cP oe i EE BER HES E E 9ow ow ww
3. IPC910H Series Embedded System User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document AXIOMTEK does not make any commitment to update the information in this manual AXIOMTEK reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd Copyright 2008 AXIOMTEK Co Ltd All Rights Reserved December 2008 Version A3 Printed in Taiwan Safety Precautions Before getting started please read the following important safety precautions 1 The IPC910H Series does not come equipped with an operating system An operating system must be loaded first before installing any software into the computer Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic components in any static shielded devices Most electr
4. En Menu Level p Reset Configuration Data Disabled Resources Controlled By Aute lt ESCD gt PCIVGA Palette Snoop Disabled Maximum Payload Size 128 j Move Enter Select PURPO Value FilcSave ESG Exi FisGeneral Help FS Previous Values FF Optimized Defaults Init Display First This item allows you to decide whether PCI Slot or AGP to be the first primary display card Reset Configuration Data Normally you leave this item Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup or if installing a new add on cause the system reconfiguration a serious conflict that the operating system can not boot Options Enabled Disabled Resources Controlled By The Award Plug and Play BIOS can automatically configure all boot and Plug and Play compatible devices If you select Auto all interrupt request IRQ DMA assignment and Used DMA fields Phoenix Award BIOS Utility 49 IPC910H Series User s Manual disappear as the BIOS automatically assigns them The default value is Manual e IRQ Resources When resources are controlled manually assign each system interrupt to one of the following types in accordance with the type of devices using the interrupt 1 Legacy ISA Devices compliant with the original PC AT bus specification requiring a specific interrupt such as IRQA for serial port 1 2 PCI ISA PnP Devices compliant with the Plug and Play standard whe
5. HDD Hard Disk Drive and PCle card The chapter 2 will show you how to install the hardware It includes 2 1 Installing the Processor The Intel Pentium M Processor is available as a boxed processor for laptop computers in the micro FCPGA form factor Intel recommends the processor should be installed by a computer professional since this electronic device may cause serious damage to the installer system and processor if installed improperly Important Notes Before attempting to install a new processor carefully review the documentation that came with your system and make sure that you will not be voiding your warranty by opening the computer or replacing your processor Instructions 1 Make sure that your system can accommodate the Intel Pentium M Processor that you want to install Check for motherboard BIOS and thermal compatibility by using the manufacturer s documentation for the laptop computer or by contacting the vendor if necessary This processor should only be installed in systems supporting the Intel Pentium M Processor Important Notes Do not use an Intel Pentium M Processor in a desktop system and do not use a desktop processor in an Inte Pentium M Processor notebook Since these processors have different electrical specifications damage to the processor and system can occur 2 Obtain access to your processor socket as described in the documentation for your system Hardware Installation 11
6. Health Stalus uui mao iici e ea ndis rr ora aed ep e pira kia fed id 51 3 12 Frequency Voltage Control essere 52 3 13 Load Optimized Detaults 3 ec e ed e b eet 53 3 14 Set Supervisor User Password cccccccscscscecceeceeeeeeeeeaeaneeanananananeeaes 54 3 15 Save amp EXT OGD oree a e lica teiwsstusodtu stus u tote gute outs 55 3 16 Exit VWithOUl SAVING estes eda tenete eO coco area ee 56 Vii MEMO viii IPC910H Series User s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and a detailed specification of the IPC910H Series Chapter 1 includes the following sections General Description System Specification Dimensions I O Outlets Package List 1 1 General Description The Mir uid is an Pine i system that can support Socket M for Intel Core 2 Duo Core Duo or Celeron M processors The IPC910H Series supports Windows 2000 Windows XP and Windows XP embedded suitable for the most endurable operation Introduction 1 IPC910H Series User s Manual Reliable and Stable Design The IPC910H Series adopts an anti vibration hard drive bay which makes it especially suitable for vibration environments best for industrial automation digital signage and gaming application Embedded O S Supported 1 2 1 2 The IPC910H Series not only supports Windows 2000 Windows XP but also supports embedded OS such as Windows XP embedded For storage
7. The function is always Enablea e ACPI Suspend Type This item specifies the power saving modes for ACPI function If your operating system supports ACPI such as Windows 98SE Windows ME and Windows 2000 you can choose to enter the Standby mode in S1 POS or S3 STR fashion through the setting 46 Phoenix Award BIOS Utility IPC910H Series User s Manual of this field Options are S1 POS The S1 sleep mode is a low power state In this state no system context is lost CPU or chipset and hardware maintains all system contexts S3 STR The S3 sleep mode is a lower power state where the information of system configuration and open applications files is saved to main memory that remains powered while most other hardware components turn off to save energy The information stored in memory will be used to restore the system when a wake up event occurs e Power Management This option allows you to select the type or degree of power saving for Doze Standby and Suspend modes The table below describes each power management mode It is maximum power savings only available for SL CPUs The inactivity period is 1 minute in each mode It sets each mode Select time out periods in the PM User Define _ Timers section It is minimum power savings The inactivity period is 1 hour in each mode except the hard drive Disabled Default value e Video Off Method This setting determines the manner in which the monitor is
8. table only for Option Page Setup Menu Load the Setup default only for Option Page Setup Menu Reserved F5 key F6 key F7 key Reserved Save all the CMOS changes only for Main Menu 3 3 Getting Help e Main Menu The online description of the highlighted setup function is displayed at the bottom of the screen e Status Page Setup Menu Option Page Setup Menu Press F1 to pop out a small Help window that provides the description of using appropriate keys and possible selections for highlighted items Press F1 or Esc to exit the Help Window 26 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 4 The Main Menu Once you enter the Award BIOS CMOS Setup Utility the Main Menu appears on the screen In the Main Menu there are several Setup functions and a couple of Exit options for your selection Use arrow keys to select the Setup Page you intend to configure then press lt Enter gt to accept or enter its sub menu Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control P Advanced BIOS Features Load Optimized Defaults F Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving b PC Health Status Esc Quit _ Select Item F10 Save amp Exit Setup sy y NOTE lf your computer can not boot after making and saving sy
9. Card when Backplane HAB103 installed E Su Notes The system provides PCI amp PCle slots when backplane HAB103 is installed You can install one PCI and one PCle x4 Step 1 Turn off the system Step 2 Disconnect the power connector Step 3 Loosen screws to remove the side cover from the chassis Removing the PCI bracket by releasing the button as marked 22 Hardware Installation IPC910H Series User s Manual Step 4 Locate the PCle slots from the side e s s m m m w SES SB BEBE a 6 s s mw m m i ee u aa se B 5p M B M 3 FER SB 8 i CTTETTTTTTITIII Step 5 Align the PCle card with the slot and press the card into the Step 6 slot until it is firmly seated One PCI and one PCle x4 can be installed Put brackets side cover back to the chassis fasten all buttons and screws Hardware Installation 23 IPC910H Series User s Manual MEMO 24 Hardware Installation IPC910H Series User s Manual CHAPTER 3 PHOENIX AWARD BIOS UTILITY The Phoenix Award BIOS provides users with a built in Setup program to modify basic system configuration All configured parameters are stored in a battery backed up RAM CMOS RAM to save the Setup information whenever the power is turned off 3 1 Entering Setup There are two ways to enter the Setup program You may either turn ON the computer and press Del immediately or press the lt Del gt and or Ctrl Alt and Esc keys simultaneously when
10. IPC910H Series User s Manual 3 If the cooling solution prevents you from accessing the processor Socket you may need to remove it Instructions on how to remove your cooling solution should be provided in the documentation that came with the system To un install the current processor use a screwdriver to disengage open the socket actuator as shown in Figure 1 below The most commonly used sockets are Molex or FoxConn sockets so they are used in the illustrations below The socket actuator should open after only a half turn or so and you should then be able to remove the processor with your fingers Procedure of Installation Step 1 Turn off the system Step 2 Disconnect the power connector Step 3 Loosen screws to remove the top and side covers from the chassis Hardware Installation IPC910H Series User s Manual Step 4 After opening the top and side covers you can locate the CPU socket and heatsink as marked Step 5 Align pins of the CPU with pin holes of the socket Be careful of the CPU s orientation that you need to align the arrow mark on the CPU with the arrow key on the socket Place the CPU into the socket and use a screwdriver to lock it onto the Socket Hardware Installation 13 IPC910H Series User s Manual Step 6 Place the CPU Heatsink on the CPU and lock it by pushing down the fixing buttons Step 7 Close the side and top covers back to the chassis and fasten all screws
11. PCI amp one PCle slots one PCI amp one PCle x4 when backplane HAB103 installed BS 7 NOTE The safe value of 12V voltage for one expansion card is between 0 6A 0 8A the maximum value for two expansion cards can t exceed 2A 1 2 3 System Specification e Drive Capacity m Supports one 2 5 HDD driver bay one onboard Introduction 3 IPC910H Series User s Manual CompactFlash M Socket e Power Input m 18VDC to 28VDC with phoenix power plug m External 90W AC Adapter Power Input 90VAC to 264VAC 6 32A 47 63HZ Power Output 19VDC e Operation Temperature m Ambient with air flow 5 C 45 C e Storage Temperature m 20 C 80 C e Humidity m 10 90 Non condensing e Dimensions m 188mm W x 241 2mm D x 150 4mm H A M NOTE All specifications and images are subject to change without notice 4 Introduction IPC910H Series User s Manual imensions 1 3 D The following diagrams show you dimensions and outlines of the IPC910H Series LELEREELETEETETEI p LE Introduction IPC910H Series User s Manual 1 4 I O Outlets The following figures show you I O outlets on front and rear panels of the IPC910H Series VGA e Rear Panel ig 2 0 VGA PORT oi mm PS 2x1 K B M S POWER SWITCH POWER r CONNECTOR EDIT DIN JACKor E POENIX PLUG REMOTE cOM4 COM3 POWER coM2 COM4 SWITCH e Front EET UL TOA of Be y USB 2 0 x2 VA AXIOMT
12. blanked V H It turns OFF vertical and horizontal synchronization ports SYNC Blank jand writes blanks to the video buffer Select this option if your monitor supports the Display Power Management Signaling DPMS standard of the Video Electronics Standards Association VESA Use the supplied software for your video subsystem to select video power management values Blank Screen The System only writes blanks to the video buffer e Video Off In Suspend This item defines if the video is powered down when the system is put into suspend mode Phoenix Award BIOS Utility 47 IPC910H Series User s Manual e Suspend Type If this item is set to the default Stop Grant the CPU will go into Idle Mode during power saving mode e Suspend Mode After a selected period of system inactivity 1 minute to 1 hour all devices except the CPU shut off The default value is Disabled Disabled The System will never enter the SUSPEND mode 1 2 4 6 8 10 2 It defines continuous idle time before the system 0 30 40 entering the SUSPEND mode Min 1 Hr If any item defined in J is enabled and active the SUSPEND timer will be reloaded e HDD Power Down If HDD activity is not detected for a specified length of time in this field the hard disk drive will be powered down while other devices remain active e Soft Off by PWR BTTN This option only works with systems using an ATX power supply It also allows users to define which type
13. device the IPC910H Series supports one 2 5 HDD driver bay and one onboard CompactFlash socket System Specifications 1 Main CPU Board CPU m Socket type Intel Core 2 Duo Core Duo or Celeron M processors System Chipset m Intel 945GME chipset BIOS m Phoenix Award BIOS 4Mbit with RPL PXE LAN Boot ROM omartView and Customer CMOS Backup System Memory m Two 200 pin DDR2 533 667 MHz SODIMM sockets with maximum up to 4GB Features m Supports Dual 1000 100 10 LAN ports m Supports six USB 2 0 VGA m Supports three RS232 and one RS232 422 485 DB9 connectors Supports two PCle or one PCI amp one PICe expansion slots DC to DC power supply support 18V to 28V Introduction IPC910H Series User s Manual 1 2 2 O System e l Olnterface Rear m ATX power on off switch m One2 pin connector output for remote power on off switch m 18VDC to 28VDC with phoenix power plug or External 90W AC Adapter m One PS 2 keyboard mouse connector m One VGA connector m Two USB 2 0 ports m wo G E LAN ports m One DB 9 as COM1 for RS232 422 485 7M Note The default setting of COM1 is RS232 The RS422 485 mode of COM 1 can be supported by adjusting the jumper inside the system m Three RS 232 COM Ports as COM2 COM3 COM4 e l Olnterface Front m Four USB 2 0 ports m HDD access power LEDs e Expansion Slot m wo PCle slots one PCle x1 amp one PCle x4 or two PCle x1 when backplane HAB100 installed m One
14. function key from 1 to 31 Date It is from January to December It shows the current year of BIOS e Time This item shows current time of your system with the format hour minute second The time is calculated based on the 24 hour military time clock For example 1 p m is 13 00 00 28 Phoenix Award BIOS Utility IPC910H Series User s Manual IDE Channel 0 1 2 3 Master IDE Channel 0 1 2 3 Slave These items identify the types of each IDE channel installed in the computer There are 45 predefined types Type 1 to Type 45 and2 user s definable types Type User for Enhanced IDE BIOS Press lt PgUp gt lt gt or lt PgDn gt lt gt to select a numbered hard disk type or directly type the number and press Enter Please be noted your drive s specifications must match the drive table The hard disk will not work properly if you enter improper information If your hard disk drive type does not match or is not listed you can use Type User to manually define your own drive type If selecting Type User you will be asked to enter related information in the following items Directly key in the information and press Enter This information should be provided in the documentation from your hard disk vendor or the system manufacturer If the HDD interface controller supports ESDI select Type 1 If the HDD interface controller supports SCSI select None If the HDD interface controller supports CD ROM select
15. modifications Type N to return to the Setup utility Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control P Advanced BIOS Features Load Optimized Defaults P Advanced Chipset Features Set Supervisor Password Integrated Peripherals set User Password Setup Quit Without Saving Y N Y saving Esc Quit Select item F10 Save amp Exit Setup Display CPU System Temperature Fan speed 56 Phoenix Award BIOS Utility
16. of soft power OFF sequence the system will follow The default value is Instant Off This option follows the conventional manner of system performance when turning the power to OFF Instant Off is a software power OFF sequence requiring the power supply button is switched to OFF Upon the system s turning OFF through the power switch this option will delay the complete system power Delay 4 Sec OFF sequence approximately 4 seconds Within this delay period the system will temporarily enter into the Suspend Mode enabling you to restart the system at once e Power On by Ring This option allows the system to resume or wake up upon detecting any ring signals coming from an installed modem The default value is Enabled e Resume by Alarm If enable this item the system can automatically resume after a fixed time in accordance with the system s RTC realtime clock Press Esc to return to the Main Menu page 48 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 10 PnP PCI Configuration Setup This section describes the configuration of PCI Personal Computer Interconnect bus system which allows I O devices to operate at speeds close to the CPU speed while communicating with other important components This section covers very technical items that only experienced users could change default settings Phoenix AwardBlOos CMOS Setup Utility PnP PCI Configurations item Help Init Display First PCI Slot ad
17. the following message appears at the bottom of the screen during POST Power on Self Test TO ENTER SETUP PRESS DEL KEY If the message disappears before you respond and you still want to enter Setup please restart the system to try it again Turning the system power OFF and ON pressing the RESET button on the System case or simultaneously pressing Ctrl Alt and Del keys can restart the system If you do not press keys at the right time and the system doesn t boot an error message will pop out to prompt you the following information PRESS F1 TO CONTINUE lt CTRL ALT ESC gt OR DEL TO ENTER SETUP Phoenix Award BIOS Utility 25 IPC910H Series User s Manual 3 2 Control Keys Uparow Mevecusormeprveus em IRightarrow Move to tne tem inthe ighthand Main Menu Quit and delete changes into CMOS Esc key Status Page Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu PqUp ke Increase the numeric value or make changes PgDn key Decrease the numeric value or make changes General help only for Status Page Setup Menu and Option Page Setup Menu Change color from total 16 colors F2 to select color Shift F2 key forward Shift F2 to select color backward F3 key Reserved F1 key F4 key Reserved Restore the previous CMOS value from CMOS only for Option Page Setup Menu Load the default CMOS value from BIOS default
18. the BIOS will check if a PCI Express graphics card is installed or not If a PCI Phoenix Award BIOS Utility 37 IPC910H Series User s Manual Express graphics card is detected the board will boot up using that card Otherwise it is defaulted to the onchip graphics processor e On Chip Frame Buffer Size Use this item to set the VGA frame buffer size e DVMT Mode DVMT Dynamic Video Memory Technology helps you select the video mode e DVMT Fixed Memory Size DVMT Dynamic Video Memory Technology allows you to select a maximum size of dynamic amount usage of the video memory The system would configure the video memory dependent on your application e Boot Display This item is to select Display Device that the screen will be shown e PanelScaling This item shows the setting of panel scaling and operates the scaling function that the panel output can fit the screen resolution connected to the output port e Panel Number This item is to select panel resolution that you want Press Esc to return to the Main Menu page 38 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 8 Integrated Peripherals This section allows you to configure your SuperlO Device IDE Function and Onboard Device Phoenix AwardBlOos CMOS Setup Utility Integrated Peripherals ltem Help Menu Level P OnChip IDE Device Press Enter F Onboard Device Press Enter Super IO Device Press Enter Onboard Serial Port 3 SEB Serial P
19. transfer access Automatic data transfer between system memory and IDE device with minimum CPU intervention This improves data throughput and frees CPU to perform other tasks On Chip Primary Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately The default value is Enabled RS NOTE Choosing Disabled for these options will Phoenix Award BIOS Utility IPC910H Series User s Manual automatically remove the IDE Primary Master Slave PIO and or IDE Secondary Master Slave PIO items on the menu gt IDE Primary Secondary Master Slave PIO The four IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes 0 to 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device gt IDE Primary Secondary Master Slave UDMA Select the mode of operation for the IDE drive Ultra DMA 33 66 100 133 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver If your hard drive and system software both support Ultra DMA 33 66 100 133 select Auto to enable UDMA mode by BIOS On Chip Serial ATA Setting SATA Mode There are these options for you to set up SATA mode IDE RAID or AHCI On Chip Serial ATA Use this
20. D va P as nd DH ee ae 3 1 2 3 System SPECICATION T E 3 1 3 IDiMNG SIONS co secs Er PE 5 1 4 VO UMC PD 6 1 5 JUIMPEr SCUINGS 1534 wa acere ditis ex e cpi et irre dined a ee 7 1 6 PACKING d ci CLE 9 CHAPTER 2 HARDWARE INSTALLATION eeeeeeeeeeenenen nennen 11 2 1 Installing the Processor ccccccssssseeeececnssseeeeeceeeesseeeesesseaeeeeesesnageeees 11 2 2 Installing the Memory Module sese 15 2 3 Installing the Hard Disk Drive ccccccccsssseeeeeeceeeeeeeeeseaseeseeeesseaeaseees 17 2 4 Installing the PCle Card when Backplane HAB100 installed 19 2 5 Installing the PCle Card when Backplane HAB103 installed 22 CHAPTER 3 PHOENIX AWARD BIOS UTILITY esses 25 3 1 Enterngselilbruseens cuiu vu entree ee rtt tu etinm tuu e MM UE UE 25 3 2 ODIO KEYS osi socchiediequts cB anand Sta teste neta Eua oe ipsu acces n e tcp a 26 3 3 Ge HNG Telly joss E D EE 26 3 4 AUI ce 27 3 5 Standard CMOS Setup Menu eeeeeeesesseseseseeeeee eren erre 28 3 6 Advanced BIOS Features sse 31 3 7 Advanced Chipset Features seen 37 3 8 Integrated Peripherals esses 39 3 9 Power Management Setup cccccccccccccceceeceeeeceeeeeeeeeeeeeeeeeeeeeeeeneneneness 45 3 10 PhP PCI GontiQUraiorn SelliDsasss R cade pad eppex ME pce pru EE 49 3 11 PO
21. EK 6 Introduction IPC910H Series User s Manual 1 5 Jumper Settings The IPC910H has a number of jumpers inside the chassis that allow you to configure your system to suit your application The table below lists the functions of the various jumpers 5V HI Selection DCD 5V RI 12V Normal Clear CMOS Default CF Master Slave Master Slave Default d Introduction 7 IPC910H Series User s Manual COM1 RS232 422 485 Jumper Setting JP2 Default 24 65 ERE ooo 1357 JP3 JP4 Backplane Jumper Setting Use this jumper to select PCle x1 or PCle x 4 by the following setting Introduction IPC910H Series User s Manual 1 6 Packing List The package bundled with your IPC910H Series should contain the following items IPC910H Series Unit x 1 DIN 6P 6P PS 2 KB MOUSE RO x 1 TB HD 515 3P F 180D P 5 08 GREEN RC x 1 for IPC910H P External Power Switch Cable 19V 90W Adapter for IPC910H D Driver CD Quick Manual Wall Mount Bracket x 2 TMS M4 6 RC x 12 Power cord USA 2pin YP11 YC13 L 1830mm x 1 for IPC910H D If you can not find this package or any items are missing please contact AXIOMTEK distributors immediately Introduction 9 IPC910H Series User s Manual MEMO 10 Introduction IPC910H Series User s Manual CHAPTER 2 HARDWARE INSTALLATION The IPC910H Series are convenient for your various hardware configurations such as CPU Central Processing Unit Memory Module
22. None CYLS number of cylinders LANDZONE HEADS number of heads SECTORS PRECOMP write precom MODE HDD access mode If there is no hard disk drive installed select NONE and press Enter Drive A Select the type of floppy drive installed in your system and the default is None Phoenix Award BIOS Utility 29 IPC910H Series User s Manual e Halt On This ttem determines whether the system will halt or not if an error is detected while powering up The system booting will halt on any errors detected default Whenever BIOS detects a non fatal error the system will stop and you will be prompted The system booting will not stop for a keyboard All But parce Keunoarcd error it will stop for other errors All But The system booting will not stop for a disk error it Diskette will stop for other errors All But The system booting will not stop for a keyboard or Disk Ke disk error it will stop for other errors Press lt Esc gt to return to the Main Menu page 30 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 6 Advanced BIOS Features This section allows you to configure and improve your system to set up some system features according to your preference E CPU Feature t Hard Disk Boot Priority Virus Warning CPU L1 amp L2 Cache Quick Power On Shelf Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Boot Up Floppy Seek Boot Up Nu
23. Siti cae ae Hardware Installation 17 IPC910H Series User s Manual Step 5 Use assembly parts to fix HDD with the bracket Step 6 Install and fix the HDD through the bottom next plug the power cable in HDD m mmm Ree PPP rere SET ERPs Fh SN E TETTE ITITI DIIIIIII dresses eril 7 Step 7 Close the side cover back to the chassis and fasten all screws 18 Hardware Installation IPC910H Series User s Manual 2 4 Installing the PCle Card when Backplane HAB100 installed BS Notes The system provides two PCle slots when backplane HAB100 is installed You can install one PCle x1 and one PCle x4 or two PCle x1 Step 1 Turn off the system Step 2 Disconnect the power connector Step 3 Loosen screws to remove the side cover from the chassis Removing the PCI bracket by releasing the button as marked Hardware Installation 19 IPC910H Series User s Manual Step 4 Locate the PCle slots from the side 2 r KERRIE amp Step 5 Align the PCle card with the slot and press the card into the slot until it is firmly seated son o NY PEEEL ELE 20 Hardware Installation IPC910H Series User s Manual Step 6 One PCle x1 and one PCle x4 can be installed or two PCle XT NHLTLESSLIELIELIELT 1 tia LPR head Step 7 Close the side cover back to the chassis and fasten all screws Hardware Installation 21 IPC910H Series User s Manual 2 5 Installing the PCle
24. a USB keyboard gt AC 97 Audio Use this item to enable or disable the onboard AC 97 Audio function Press lt Esc gt to return to the Integrated Peripherals page 42 Phoenix Award BIOS Utility e Super IO Device IPC910H Series User s Manual Scroll to this item and press lt Enter gt to view the sub menu Super IO Device Phoenix AwardBlOS CMOS Setup Utility POWER ON Function Onboard FOC Controller Onboard Serial Port 1 Onboard Serial Port 2 Onboard Parallel Port Parallel Port Mode PWRON After PWR Fail Super iO Device item Help BUTTON ONLY Menu Level i Enabled 3F8 IRQ4 2F8 IRQ3 ETE TTA SPP Former Sts j 1 Mya EnterSelact PUPO Value FilcSave ESG Exit mirus FF Optimized Defaults F5 Previous Values POWER ON Function This item provides several ways to power up the system BUTTON ONLY Keyboard 98 Password Hot Key Mouse Left Mouse Right and Any Key Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you want to use it If you install and in FDC or the system has no floppy drive select Disabled in this field Options Enabled and Disabled Onboard Serial Port 1 2 Select an address and corresponding interrupt for the serial port Options 3F8 IRQ4 2E8 IRQ3 3E8 IRQ4 2F8 IRQ3 Disabled Auto Onboard Parallel Port This item allows you to determine the I O address for onboard par
25. allel port Options 378H IRQ7 278H IRQ5 3BC IRQ7 and Disabled Phoenix Award BIOS Utility 43 IPC910H Series User s Manual Parallel Port Mode Select an operating mode for the onboard parallel printer port Select Normal unless your hardware and software require another mode in this field Options EPP1 9 ECP SPP ECPEPP1 7 EPP1 7 EPP Mode Select Select EPP port type 1 7 or 1 9 ECP Mode Use DMA Select a DMA channel for the parallel port while using the ECP mode PWRON After PWR Fail This ttem enables your computer to automatically restart or return to its operating status Press lt Esc gt to return to the Integrated Peripherals page e Onboard Serial Port 3 This item assigns which I O address to access onboard serial port 3 e Serial Port 3 Use IRQ This item selects a corresponding interrupt for the third serial port e Onboard Serial Port 4 This item assigns which I O address to access onboard serial port 4 e Serial Port 4 Use IRQ This item selects a corresponding interrupt for the fourth serial port Press lt Esc gt to return to the Main Menu page 44 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 9 Power Management Setup The Power Management Setup allows you to save energy of your system effectively It will shut down the hard disk and turn OFF video display after a period of inactivity Phoenix AwardBlOos CMOS Setup Utility Power Management Setup E PCI Express PM Fun
26. ard BIOS Utility IPC910H Series User s Manual e Hard Disk Boot Priority Scroll to this item and press lt Enter gt to view the sub menu to decide the disk boot priority Phoenix AwardBlOos CMOS Setup Utility Hard Disk Boot Priority item Help Menu Level amp 1 Chi FUJI SU MAY ZUH 2 Bootable Add in Cards Use lt gt or lt gt to select a device then press lt gt to move it up or to move it down the list Press lt ESC gt to axit this Lun Move Enter Select JPU PD Value F1 Save ESC Exit Fi General Help Fo Previous Values FF Optimized Defaults Press lt Esc gt to return to the Advanced BIOS Features page Phoenix Award BIOS Utility 33 IPC910H Series User s Manual e Virus Warning This option flashes on the screen During and after the system boot up any attempt to write to the boot sector or partition table of the hard disk drive will halt the system with the following message You can run an anti virus program to locate the problem The default setting is Disabled WARNING Disk boot sector is to be modified Type Y to accept write or N to abort write Award Software Inc It automatically activates while the system Enabled boots up and a warning message appears for an attempt to access the boot sector or hard disk partition table Disabled No warning message will appear for attempts to access the boot sector or hard disk partition table B
27. ction ACP Function ACP Suspend Type Power Management Video Off Method Video Of In Suspend Suspend Type suspend Mode HDD Power Down Soft Off by PWR BTTN Power On by Ring Resume by Alarm Phoenix Award BIOS Utility F5 Previous Values item Help Menu Level p Press Enter Enabled ETE 3 Min Saving DPMS Yes Stop Grant Disabled Disabled Instant Off Disabled Disabled dj EnterSelact PURPO Value FileSave ESC Esit FioGeneral Help FF Optimized Defaults 45 IPC910H Series User s Manual e PCI Express PM Function Scroll to this item and press Enter to view the sub menu of PCI Express PM Function Scroll to this item and press Enter to view the sub menu of PCI Express PM Function PCI Express components are permitted to wakeup the system using a wakeup mechanism followed by a power management event PME Message Phoenix AwardBlOS CMOS Setup Utility PCI Expreas PM Func Item Help PCI Express PME Enabled Menu Level b i Move Enter Select PUNRPD Value Fil Save ESCIExit FisGeneral Help F5 Previaus Values FT Optimized Defaults gt PCI Express PME This option performs the same function as Wake Up by PCI card but is for PCIExpress cards Options Enabled and Disabled Press Esc to return to the Power Management Setup page e ACPI Function This item allows you to enable disable the Advanced Configuration and Power Management ACPI
28. entiate 720K 1 2M or 1 44M drive type as they all are 80 tracks Enabled BIOS will not search for the type of floppy disk drive by Disabled track number There will be no warning message displayed if the installed drive is 360K e Boot Up NumLock Status Set the the Num Lock status when the system is powered on The default value is On e Security Option This item allows you to limit access to the system and Setup or just to Setup The default value is Setup System If a wrong password is entered at the prompt the system will not boot the access to Setup will be denied either If a wrong password is entered at the prompt the system will boot but the access to Setup will be denied X NOTE To disable the security select PASSWORD SETTING at Main Menu and then you will be asked to enter a password Do not type anything just press lt Enter gt and it will disable the security Once the security is disabled the system will boot and you can enter Setup freely Phoenix Award BIOS Utility 35 IPC910H Series User s Manual e APIC Mode Use this item to enable or disable APIC Advanced Programmable Interrupt Controller mode that provides symmetric multi processing SMP for systems e MPS Version Control For OS This item specifies the version of the Multiprocessor Specification MPS Version 1 4 has extended configuration tables to improve support for multiple PCI bus configurations and provide future ex
29. hat component if this is the case it will be mentioned in the cleaning e Cloth A piece of cloth is the best tool to use when rubbing up a component Although paper towels or tissues can be used on most hardware as well we still recommend you to rub it with a piece of cloth e Water or rubbing alcohol You may moisten a piece of cloth a bit with some water or rubbing alcohol and rub it on the computer Unknown solvents may be harmful to the plastics parts e Vacuum cleaner Absorb the dust dirt hair cigarette particles and other particles out of a computer can be one of the best methods of cleaning a computer Over time these items can restrict the airflow in a computer and cause circuitry to corrode e Cotton swabs Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard mouse and other locations e Foam swabs Whenever possible it is better to use lint free swabs such as foam swabs RU Note It is strongly recommended that you should shut down the system before you start to clean any single components Please follow the steps below Close all application programs Close operating software Turn off power switch Remove all device Pull out power cable QV m CDI S Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair we strongly recommended that you should inform your AXIOMTEK distributor as soon as poss
30. he Setup It prevents any unauthorized persons from changing your system configuration Additionally when a password is enabled you can also require the BIOS to request a password every time the system reboots This would prevent unauthorized use of your computer You decide when the password is required for the BIOS Features Setup Menu and its Security option If the Security option is set to System the password is required during booting up and entry into the Setup if it is set as Setup a prompt will only appear before entering the Setup 54 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 15 Save amp Exit Setup This section allows you to determine whether or not to accept your modifications Type Y to quit the setup utility and save all changes into the CMOS memory Type N to bring you back to the Setup utility Phoenix AwardBlOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control P Advanced BIOS Features Load Optimized Defaults P Advanced Chipset Features Set Supervisor Password Integrated Peripherals set User Password Esc Quit F10 Save amp Exit Setup Display CPU System Temperature Fan speed Phoenix Award BIOS Utility 55 IPC910H Series User s Manual 3 16 Exit Without Saving Select this option to exit the Setup utility without saving changes you have made in this session Type Y and it will quit the Setup utility without saving your
31. ible for the suitable solution For the computers that are no longer useful or no longer working well please contact your AXIOMTEK distributor for recycling and we will make the proper arrangement Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Pentium are registered trademarks of Intel Corporation MS DOS Microsoft C and QuickBASIC are trademarks of Microsoft Corporation VIA is a trademark of VIA Technologies Inc SST is a trademark of Silicon Storage Technology Inc UMC is a trademark of United Microelectronics Corporation Other brand names and trademarks are the properties and registered brands of their respective owners yi Table of Contents Disclaimers e cmt ii Salely PRECAULONS nico cece cec ces eror pco ee cep see dede cu css E seeds eee iii GTASSIICAUONN e c aE aAA A E E eE eE Ee SE iv General Cleaning TIDS 2 eeoe e tcu aeneae naa Fu Ee RUP a a aad a iv Scrap Computer Recycling cissie 5 ope etse oe oe ce eesti aceeh oe oo pa ee ipeo nones vae e Min EU vi CHAPTER 1 INTRODUCTION siue aiaosa ne arae eco Deae gen qna 6 aee cese tcc cran a re icine sere Ces 1 1 1 General Descriptions niian aeaeennsoe aan an 1 1 2 System SpeCIfICallOFiS ees iisrael peer veas Qe pire eed oido bx eroe E dated 2 1 2 1 Malt P EHBOSEG i tci ect E DE E UE RIEd UR 2 1 2 2 9 VS LOT TI codice desde dread deas eis car o N
32. item to enable or disable the built in on chip serial ATA SATA PORT Speed Settings Use this item to select SATA or SATA II device support forcedly PATA IDE Mode Use this item to set the PATA IDE mode When set to Primary P1 and P3 are Secondary on the other hand when set to Secondary PO and P2 are Primary SATA Port If the PATA IDE Mode is Primary P1 P3 is Secondary will be shown to mean SATA 2 and SATA 4 are Secondary If the PATA IDE Mode is Secondary PO P2 is Primary will be shown to mean SATA 1 and SATA 3 are Primary Press Esc to return to the Integrated Peripherals page Phoenix Award BIOS Utility 41 IPC910H Series User s Manual e Onboard Device Scroll to this item and press lt Enter gt to view the sub menu Onboard Device Phoenix AwardBlOsS CMOS Setup Utility Onboard Device Item Help Menu Level i USB Controller Enabled USB 2 0 Controller Enabled USB Keyboard Support Disabled ACST Audio Auto Movo EnterSelect PUPD Value Flt Save ESC Exit F1 General Help F5 Previaus Values FF Optimized Defaults gt USB Controller Enable this item if you are using the USB in the system You should disable this item if a higher level controller is added gt USB 2 0 Controller Enable this item if you are using the EHCI USB2 0 controller in the system gt USB Keyboard Support Enable this item if the system has a Universal Serial Bus USB controller and you have
33. mLock Status Security Option APIC Mode MPS Version Control For Q5 OS Select For DRAM gt 64MB Phoenix AwardBlOos CMOS Setup Utility Advanced BIOS Features Item Help Press Enter Press Enter Disabled Enabled Enabled Floppy Hard Disk CDROM Enabled Disabled On Setup Enabled 1 4 Non OS2 Menu Level i F5 Prewiaus Values Move Enter Select PU PD Valua Fil Save ESC Exi F1 General Help FF Optimized Defaults Phoenix Award BIOS Utility 31 IPC910H Series User s Manual e CPU Feature Scroll to this item and press Enter to view the CPU Feature sub menu Phoenix AwardBlOsS CMOS Setup Utility CPU Features item Help Menu Level i Delay Prior to Thermal 16 Min Thermal Management Thermal Monitor 2 CAE Function Auto Execute Disable Bit Enabled Virtual ization Technology Enabled Move Enter Select JPU PD Value Fil Save ESC Exit Fi2General Help F5 Previous Values FT Optimized Defaults gt Delay prior to Thermal This filed is used to select the time that would force the CPU to a 50 duty cycle when it exceeds its maximum operating temperature therefore protecting the CPU and the system board from overheating to ensure a safe computing environment gt Thermal Management Thermal Monitor 1 On die throttling Thermal Monitor 2 Ratio and VID transition Press Esc to return to the Advanced BIOS Features page 32 Phoenix Aw
34. onic components are sensitive to static electrical charge Disconnect the power cord from the IPC910H Series before making any installation Be sure both the system and the external devices are turned OFF Sudden surge of power could ruin sensitive components Make sure the IPC910H Series is properly grounded Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Turn OFF the system power before cleaning Clean the system using a cloth only Do not spray any liquid cleaner directly onto the screen Do not leave this equipment in an uncontrolled environment where the storage temperature is below 20 C or above 60 C It may damage the equipment Do not open the system s back cover If opening the cover for maintenance is a must only a trained technician is allowed to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body When handling boards and components wear a wrist grounding strap available from most electronic component stores Classification Degree of production against electric shock not classified Degree of protection against the ingress of water IPXO 3 Eq
35. ort 3 Use IRG IRQ10 Onboard Serial Port 4 2E serial Port 4 Use IRG R011 Move Enter Selest PUPD Value Fil Save ESC Exi FliGeneral Help F5 Previaus Values PF Optimized Defaults Phoenix Award BIOS Utility 39 IPC910H Series User s Manual e OnChip IDE Device Scroll to this item and press lt Enter gt to view the sub menu OnChip IDE Device 40 Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode Enabled Item Help IDE DMA transfer access Enabled Menu Level On Chip Primary PCI IDE Enabled IDE Primary Master PIO Auto IDE Primary Slave PIO Auto IDE Primary Master UMDA Auto IDE Primary Slave UMDA Auto On Chip Secondary PCIIDE Enabled ACI TE IDE Secondary Master PIO Auto block readiwrites per IDE Secondary Slave PIO Auto MALI ASI IDE Secondary Master UMDA Auto Puppart IDE Secondary Salve UMDA Auto If your IDE hard drive supports block mode select Enabled for automatic detection of On Chip Serial ATA Enhanced Moda SATA PORT Speed Settings IEE Move Enter Select PURPD Value FiliSave ESC ExM FliGeneral Help F5 Previaus Values FT Optimized Defaults IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sectors read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support IDE DMA
36. pandability e OS Select for DRAM gt 64MB This item allows you to access the memory over 64MB in OS 2 Press lt Esc gt to return to the Main Menu page 36 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 Advanced Chipset Features This section contains completely optimized chipset s features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your system hardware Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features item Help PCI Express Port 1 Enabled Menu Level p PCI Express Port 2 Enabled PCI Express Port 3 Enabled PCI Express Port 4 Enabled PCI Express Port 5 Enabled PCI Express Port 6 Enabled PCI E Compliancy Mode wi Oa PEG Onchip VGA Control Auto On Chip Frame Buffer Size 8MB DVMT Mode DVMT DVMT FIXED Memory Size 128MB Boot Display ERT Panel Scaling Auto Panel Number 1024 X 768 Move Enter Select PUIPD Value F10 Save ESCE FisGeneral Help F5 Previaus Values F7 Optimized Defaults e PCI Express Port 1 6 There are several PCI Express Ports for your selection e PCI E Compliancy Mode This item allows you to set the version of the PCI Express base specifications VGA Setting e PEG Onchip VGA Control This setting allows you to select whether to use the onchip graphics processor or the PCI Express card When set to Auto
37. rd Integrated Peripherals set User Password Power Ma P PnPIPCI C WIEDER Colb PER b PC Health Esc Quit Select Item F10 Save amp Exit Setup Display CPU System Temperature Fan speed To load CMOS SRAM with SETUP default values please enter Y If not please enter N Phoenix Award BIOS Utility 53 IPC910H Series User s Manual 3 14 Set Supervisor User Password You can set a supervisor or user password or both of them The differences between them are 1 Supervisor password You can enter and change the options on the setup menu 2 User password You can just enter but have no right to change the options on the setup menu When you select this function the following message will appear at the center of the screen to assist you in creating a password ENTER PASSWORD Type a maximum eight character password and press Enter This typed password will clear previously entered password from the CMOS memory You will be asked to confirm this password Type this password again and press Enter You may also press Esc to abort this selection and not enter a password To disable the password just press Enter when you are prompted to enter a password A message will confirm the password is getting disabled Once the password is disabled the system will boot and you can enter Setup freely PASSWORD DISABLED When a password is enabled you have to type it every time you enter t
38. stem changes with Setup the Award BIOS will reset your system to the CMOS default settings via its built in override feature It is strongly recommended that you should avoid changing the chipset s defaults Both Award and your system manufacturer have carefully set up these defaults that provide the best performance and reliability Phoenix Award BIOS Utility 27 IPC910H Series User s Manual 3 5 Standard CMOS Setup Menu The Standard CMOS Setup Menu displays basic information about your system Use arrow keys to highlight each item and use lt PgUp gt or lt PgDn gt key to select the value you want in each item Phoenix AwardBlOos CMOS Setup Utility Standard CMOS Features item Help Menu Level amp Change the day month year and century Date mm idd yy Thu Aug 28 2008 Time hh mm ss 10 46 54 FIDE Channel 0 Master None FIDE Channel 0 Slave None FIDE Channel 1 Master None FIDE Channel 1 Slave None FIDE Channel 2 Master Nona FIDE Channel 2 Slave None FIDE Channel 3 Master None IDE Channel 3 Slave None Drive A 1 44M 3 5 in Halt On All But Keyboard Mowe Enter Select HPPD Value Fib Save ESC Exit Fi General Help Fo Previous Values F7 Optimized Defaults e Date The date format is lt day gt lt date gt lt month gt lt year gt Press lt F3 gt to show the calendar It is determined by the BIOS and read only from Sunday y to Saturday n It can be keyed with the numerical
39. t FAN3 Speed Show you the current system fan3 temperature e Current FAN2 Speed Show you the current system fan2 temperature e Vcore 3 3V 5V 12V VBAT V 5VSB Show you the voltage of 3 3V 5V 12V Phoenix Award BIOS Utility 51 IPC910H Series User s Manual 3 12 Frequency Voltage Control This section is to control the CPU frequency and Supply Voltage DIMM OverVoltage and AGP voltage Phoenix AwardBlOs CMOS Setup Utility quency Voltage Control Auto Detect PC Clk Enabled Spread Spectrum Disabled item Help Menu Level p 7 ove Enter Select IJPUPD Value Fl Save ESC Exit FisGeneral Help F5 Previaus Values F7 Optimized Defaults e Auto Detect PCI Clk The enabled item can automatically disable the clock source for a PCI slot without a module to reduce EMI ElectroMagnetic Interference e Spread Spectrum If spread spectrum is enabled EMI ElectroMagnetic Interference generated by the system can be significantly reduced Press Esc to return to the Main Menu page 52 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 13 Load Optimized Defaults This option allows you to load your system configuration with default values These default settings are optimized to enable high performance features Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control P Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features set Supervisor Passwo
40. ther designed for PCI or ISA bus architecture The default value is PCI ISA PnP e PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This item allows you to set whether MPEG ISA VESA VGA Cards can work with PCI VGA or not When enabled a PCI VGA can work with a MPEG ISA VESA VGA card when disabled a PCI VGA cannot work with a MPEG ISA VESA Card PCI Express relative items e Maximum Payload Size When using DDR SDRAM and Buffer size selection another consideration in designing a payload memory is the size of the buffer for data storage Maximum Payload Size defines the maximum TLP Transaction Layer Packet data payload size for the device Press Esc to return to the Main Menu page 50 Phoenix Award BIOS Utility IPC910H Series User s Manual 3 11 PC Health Status This section supports hardware monitoring that lets you monitor those parameters for critical voltages temperatures and fan speed of the board Phoenix AwardBiOsS CMOS Setup Utility PC Health Status item Help Menu Level i 2 Mowe Enter Select PUMPO Value Fi1 Save EGC Exit FipGeneral Help F5 Previousg Values FF Optimized Defaults e Current System Temperature Show you the current system temperature e Current CPU Temperature The current system CPU temperature will be automatically detected by the system e Current FAN1 Speed Show you the current system fan1 temperature e Curren
41. uipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide 4 Mode of operation Continuous 9 Type of protection against electric shock Class equipment N General Cleaning Tips You may need the following precautions before you begin to clean the computer When you clean any single part or component for the computer please read and understand the details below fully When you need to clean the device please rub it with a piece of dry cloth 1 Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor 2 Turn the system off before you start to clean up the component or computer 3 Never drop the components inside the computer or get circuit board damp or wet 4 Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of cleaning Some individuals may be allergic to the ingredients 5 ry not to put any food drink or cigarette around the computer Cleaning Tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals Keep in mind that some components in your computer may only be able to be cleaned using a product designed for cleaning t
Download Pdf Manuals
Related Search