2x4 DVI Matrix AS-2124 User Manual
Contents
1. you need to configure the device by DIP Switch Set DIP Switch 2 at ON Set DIP Switch at OFF only when you need to control the device by remote control 4 of Table 1 Rotary DVI Output DVI Output2 Source 1 Pattern 4 Pattern 5 Table 2 Fig 1 shows a DIP switch from which you can select a specific output Fig 2 shows a rotary switch that allows you to select an input source or a test pattern The two switches should be configured at the same time For example if you want to set 1 display to show source 1 please follow the steps Firstly see table 1 and set DIP switch at 3 off and 4 off position output 1 Secondly turn rotary switch to O source 1 Hardware Installation Plug in a DVI Y cable to DVI Input Plug in a DVI Y cable to DVI Outputi and a Y cable to DVI Output 2 Connect source 1 and source 2 to the Y cable that plugged in DVI Input Connect display 1 and display 2 to the Y cable that plugged in DVI Output 1 Connect display 3 and display 4 to the Y cable that plugged in DVI Output 2 a S o o oa DVI Source1 DVI Source2 C l DVI Input Display 1 Display2 Display3 Display4 All I O configurations can be readily set up by the remote control through an OSD menu Below shows the OSD menu tree Power Off Monitor Test GREEN BLACK WHITE LINE DOT MOIRE MOIRE Press Menu on the remote control and then the OSD menu pops up as below In this page you can select any output2. 2x4 DVI Matrix AS 2124 User Manual Introduction The AS 2124 allows you to switch between two DVI sources and four DVI displays independently with compact pattern generator functionality Any input can be switched into any output through a remote control To simplify the switching process AS 2124 comes with an IR remote control If you don t have an IR remote control nearby AS 2124 can also be configured by two DIP switches one rotary switch and one DIP switch Furthermore the AS 2124 is designed to regenerates every signal carried to itself so that every signal sent out from the AS 2124 is as crystal clear as the original DVD Player A x i 7 DVI Matrix DVD Player B Features Pixel Rate up to 165MHz Maintains highest resolution digital video with no loss of quality Configured by IR remote control with OSD display Embedded Pattern Generator Supports EDID learning The AS 2124 can get the EDID information for the output device and pass it to the input equipment DIP switch configuration Without IR remote control the switcher can also be configured by the DIP switch and the rotary switch Can be cascaded more than two tiers The signal carried to the AS 2124 will be decoded and encoded Compact size Package Contents Gh ey INS 1x AS 2124 1x IR remote control 3x DVI Y cable 1x User Manual 1x 5V DC power adapter Technical Specifications Video Amplifier Bandwidth 1 65 Gbps I
3. nd labor in effect at the time of repair Such repairs are warranted for 90 days from the day of reshipment to the buyer If the unit is delivered by mail customers agree to insure the unit or assume the risk of loss or damage in transit Under no circumstances will a unit be accepted without a return authorization number The warranty is in lieu of all other warranties expressed or implied including without limitations any other implied warranty or fitness or merchantability for any particular purpose all of which are expressly disclaimed Proof of sale may be required in order to claim warranty Customers outside Taiwan are responsible for shipping charges to and from Ascale Cables are limited to a 30 day warranty and cable must be free from any markings scratches and neatly coiled The content of this manual has been carefully checked and is believed to be accurate However Ascale assumes no responsibility for any inaccuracies that may be contained in this manual Ascale will NOT be liable for direct indirect incidental special or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages Also the technical information contained herein regarding the ASCALE 2124 features and specifications is subject to change without further notice 10
4. nput Video Signal 1 2 volts p p Input DDC Signal 5 volts p p TTL Single Link Range 1080p 1920 x 1200 DVI Connector DVI I 29 pin female digital only Power Supply 5 VDC Power Consumption 10 watts max Dimensions 130mm 3 1 x 110mm 4 3 x 25mm 1 Lx Wx H Weight 3409 1 20z Remote Control e Figure below shows the remote control of the AS 2124 Only four arrow buttons and the menu button works The remaining buttons are reserved and no use for this product e Press Menu to launch OSD menu and use arrow buttons to move around the items in the OSD menu Right arrow button allows you to confirm your selection Press Menu again to exit the OSD menu Panel Descriptions Front View OOOOOOOTD 00000000 22 oooooooo E 20000000 oooooooo FO oooooooo FO DVI OUT1 DVI OUT2 1 2 1 Please plug in one DVI Y cable here and connect 1 and 2 DVI monitor 2 Please plug in one DVI Y cable here and connect 3 and 4 DVI monitor Rear Panel O oE ee o ID DVI IN 3 4 5 6 7 8 5V DC power jack Plug in one DVI Y cable here and connect 1 and 2 DVI sources Rotary switch For detailed setup please see the next section LED indicator EDID Power indicator 3 4 J 6 7 8 DIP Switch When the remote control is not available the switcher can also be configured by DIP switch shown as the following IR receiver Please always set DIP Switch 1 at ON When
5. port you want to configure After you press the up down arrow button on the remote control to select a specific port the menu will automatically be changed to the next page shown as below In this page you can select the video source you want to send to the port selected The input DVI connector can connect to 2 different video sources and shown as Source 1 and Source 2 If you want to save power you can turn off the chip by selecting Power Off Then the port will turn to the idle mode The Monitor Test function triggers the embedded pattern generator It can help to check dead lazy pixel and some LCD status 8 When the Monitor Test item is selected it will turn to the next OSD table shown as the following In the pattern menu each item stands for a pattern For example the first five patterns show a single color to help check dead pixels Limited Warranty Ascale warrants the AS 2124 2x4 DVI Matrix to be free from defects in the material and workmanship for 1 year from the date of purchase from Ascale or an authorized dealer Should this product fail to be in good working order within 1 year warranty period Ascale at its option repair or replace the unit provided that the unit has not been subjected to accident disaster abuse or any unauthorized modifications including static discharge and power surges Unit that fails under conditions other than those covered will be repaired at the current price of parts a
Download Pdf Manuals
Related Search