4X6 HDMI Switch/Splitter Extender over CAT.5e/6 HD4600T User's
Contents
1. and another end of the cable is connected to the RS 232 port of PC Dm m a RS 232 to 3 5mm adapter cable Connect the RS 232 adapter cable to Extender Receiver RX s RS 232 3 5mm jack and another end of the cable is connected to the RS 232 port of the 3ra party s device Disclaimer Information in this document is subject to change without notice The manufacturer does not make any representations or warranties implied or otherwise regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial damage including but not limited to special incidental consequential or other damages No part of this document may be reproduced or transmitted in any form by any means electronic or mechanical including photocopying recording or information recording and retrieval systems without the express written permission of the manufacturer All brand names and product names used in this document are trademarks or registered trademarks of their respective holders FCC Statement This device generates and uses radio frequency and may cause interference to radio and television reception if not installed and used properly This has been tested and found to comply with the limits of a Class B computing device in accordance with the specifications in Part 15 ofthe FCC Rules These specifications are designed to provide reasonable protection against such interferenc2. 00m point to point o o 3 Connection between Switch Extender Transmitter and Receiver Transmitter Receiver Choose one available RJ 45 port of the Extender Receiver RX connected with the Switch Extender Transmitter over CAT 5e or CAT 6 cable Remarks The Network Switch 10 100 enough could be transceiver for extending distance Please refer to the following connections 1 The Network Switch is linked between Switch Extender Transmitter and Receiver CAT 56 6 up to 100m CAT 5e 8 up to 100m eu Transmitter Network Hub Switch Kakalver 2 The Network Switch is possibly connected between Receiver and Receiver CAT 5e 6 up to 100m N CAT 5e 6 up to 100m CAT 5e 6 up to 100m Transmitter Receiver Network Hub Switch Receiver 4 IR Connection HDMI Source LS HDMI Cable CAT 5e 6 up to 100m Direction of IR signal from RX to TX IR Emitter Cable HDMI Cable HDMI Display IR Receiver Cable IF Connect the IR Emitter Cable to TX s 3 5mm IR jack Connect the IR Receiver Cable to RX s 3 5mm IR jack 5 RS 232 Connection HDMI Source sas dat e Be ES RS 232 to 3 5mm adapter cable HDMI Cable TX H CAT Se 6 up to 100m RX p p tu By a 4 PC Q d a g RS 232 to 3 5mm adapter cable amp 4 3rd party s device which is controlled by RS 222 port D a 4 Connect the RS 232 adapter cable to Switch Extender Transmitter RS 232 3 5mm jack
3. 4X6 HDMI Switch Splitter Extender over CAT 5e 6 HD4600T User s Manual Version 1 0 1 Introduction Thanks for purchasing the 4 x 6 HDMI Switch Splitter Extender over CAT 5e 6 Please read this Manual and retain it for reference in future if needed 1 1 Features Supports 1 source selected among 4 HDMI sources and the same source content can be done splitting displaying on remote all of 6 displays and even distributing with extending through Ethernet switch 10 100 LED indicators monitor for connection status Supports HDMI 1 3 HDCP compliant Supports resolution up to Full HD 1080p 1920 x 1080 60Hz Each corresponding extender receiver unit remote links cascade chainable additional 2 receivers for expansion Extended distance over CAT 5e 6 up to 100m point to point HDMI sources selected by front buttons IR Infrared Remote Enabled for communication of between the correspondence of switch Emitter cable and receiver unit RX Receiver cable RS232 enabled for each communication of between the correspondence of switch and receiver unit RX Supports local loop HDMI monitoring and Audio enabled 1 2 Package Contents 1 4 gt M Og d 4 x 6 HDMI Switch Splitter Extender TX x 1 DC 5V 2A Power Adapter x 1 Audio Cable 1 8m x 1 RS 232 Cable x 4 IR Emitter Cable x 4 Rack Mount Bracket x 2 1 sets User s Manual x 1 NAW VPH 2 Specifications CAT 5e CAT 6 Max Length 1
4. e in a residential installation However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by plugging the device in and out the user can try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the device and receiver Connect the computer into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CE FCC 2R40M4088
Download Pdf Manuals
Related Search