User Guide
Contents
1. YCT 603 YCT 100 BATTERY WST 512 Link transmitter with receiver fig 9 LBUR 100 can be remote controlled by wall switch or handy transmitter All ARC transmitters with other functions such like sensor function Brightness sensor transmitter and Motion sensor transmitter can also remote control LBUR 060 x Page 2 LBUR 100 when linked with code switch system transmitter is auto programmed within 256 codes OPERATION TRANSMITTER ON button control receiver ON DIMMER OFF button switches OFF all function GROUP button ALL ON or ALL OFF at same time Direct 16 controls button fig 7 amp 8 Page I 1 2 3 4 Page II 5 6 7 8 Page III 9 10 11 12 Page IV 13 14 15 16 HOW TO LINK CODE To start program your transmitter with the receiver Receiver plugged on power fig 2 Bring the transmitter near the receiver push the self program button on receiver once fig 4 ON OFF RECEIVER Press transmitter button ON to switch on Press transmitter button OFF to switch off Receiver led will blink slowly press transmitter selected ON button Receiver connected lamp will blink twice code is confirmed and led stops blinking oi Remember the transmitter button you selected for the programmed receiver lt lt 7 Transmitter and Receiver codes is auto programmed Same procedure to link with ARC code switch transmit2. OK OK L Closed 4 LBUR 100 can be used with stand lampshade of both up and down sides p4 T opened and top opening diameter over 15 cm like fig 6 shown sow eow i Diameter gt 15cm With this kind of lampshade max incandescent lamp allowed Cioka 100 watts compact fluorescent lamp energy saving lamp 60 watts AN Fig 4 OK OK i Opened l Diameter gt 15cm Note Electronic product such like LBUR 100 should be used under safe Opened 100W BOW and correct installation Lamp adoption should comply with type of lampshade to make sure LBUR 100 is under safe and correct usage g Fig 5 CAUTION Do not place two receivers near each other the distance should be above 1 meter Page 1 WARNING DO NOT OVERLOAD Pls use electronic product such like LBUR 100 under correct installation Do not use in damp places like patios cellar flammable liquid solvents paints etc LBUR 100 cannot be used with hanging lampshade with closed hanging point like fig 10 shown Remote control Transmitter Self program system transmitter fig 7 Self program system has 67 million codes which is system code Each transmitter will have very few chance to have the same code as others One of the million codes is programmed ex factory MILLION CODE SYSTEM LWST 605 LYCT 505 Code switch transmitter fig 8 Closed av KA Fig 9 CODE SWITCH SYSTEM r EEO tee
3. USER MANUAL MODEL LBUR 100 REMOTE CONTROL LAMP HOLDER RECEIVER FEATURES Self program 67 million codes Simple installation no wiring hassle g Max 100watt ON OFF function only 4 E27 lampholder 6 memory scene settings no memory loss forever l Red LED indicator for POWER ON and PROGRAMMING SETTINGS Self program Receiver compatible to all ARC transmitters Distance 30M in closed area J _ INSTALLATION Fig 1 Controller Receiver Unplugged lamp power from main line Install LBUR 100 to lampshade Install BULB to LBUR 100 Connect lampshade to AC power LED indicator on LBUR 100 should light on fig 1 Learning button LED indicator LBUR 100 lampshade installation types Closed 1 LBUR 100 cannot be used with hanging lampshade that hanging point is G closed like fig 3 shown AAN Lamp heat cannot be radiated with point closed lampshade X For LBUR 100 under safe usage jii hanging lampshade with hanging point closed is restricted Fig 2 2 LBUR 100 can be used with hanging lampshade with opened top bottom S gt Opened and diameter over 15cm like fig 4 shown j os men Ly With this type of lampshade max allowed 30 watt compact a iia fluorescent lamp energy saving lamp only K gen Opene 3 LBUR 100 can be used with stand lampshade of both up and down sides closed Fla and diameter over 15 cm like fig 5 shown 0 With this type of lampshade max allowed is 60 watts
4. mory and Receiver 2 only 2 program memory different combinations and settings can be teamed up and control from transmitter SPECIFICATION IP 20 Class I T max 40 C Frequency 433 92MHz Power 230V 10 50Hz Max load Compact fluorescent lamps Energy saving lamps 60W az Incandescent lamps 100W Page 3 A
5. ter TO CHANGE OR DELETE CODE INDIVIDUAL DELETE aa ve T1090 CODE SWITCH STS TEN A ALL MEMORY DELETE j i Push the self program button once led will blink slowly fig2 Push the self program button for 6 sec Led will blink continuously Press selected OFF button on transmitter programmed memory is deleted Receiver connected lamp will blink twice for confirmation Repeat step for re setting RECEIVER HAS 6 MEMORY SETTINGS Self program function RECEIVER has 6 memory settings It can be programmed as to your requirement with special effect It can be programmed to switch ON at one time individually or programmed with different combinations switching This means one receiver can be programmed into max 6 different combination Example if there is 3 receivers receiver 1 lamp shade receiver 2 night light receiver 3 fan Receiver 1 2 3 can be control individually with transmitter button 1 2 3 Receiver 1 3 can be programmed with transmitter button 4 lamp shade and fan ON OFF at same time Receiver 1 2 3 can also be programmed into group function ALL ON or OFF at same time into group button Release and push again once Receiver connected lamp will blink twice for confirmation ALL PROGRAMMED MEMORY WILL BE DELETED FROM RECEIVER lamp shade night light and fan ON OFF at same time Above settings Receiver 1 and 3 takes up 3 programmed me
Download Pdf Manuals
Related Search