Pet Mini Tracker User Manual
Contents
1. F 131 F 0 C 50 C Storage Temperature is between 4 F 185 F 20 C 85 C Recycle The Batteries provided in this product should be recycled to protect the local environment Please contact your local recycle department for detail Warning Do not put the batteries into the fire or heat sources It may cause danger or even explosion FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and improved to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This FCC Certifications equipment generates uses and can radiate radio frequency energy if installed and used not in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determinedly turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures mReorient or relocate the receiving antenna mlncrease the separation between the equipment and receiver mConnect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced rad2. Alert will sound Mute Press the Mute button on the Master for short range detection by way of listening to the Slave s alarm sound Wake up Standby a Switch the Master s power on and pull the plastic power strip off the Slave to start the synchronizing process The Signal indicator on the Master will start blinking simultaneously which will take 8 15 seconds to pair up provided the Slave is within range of the Master and NOT being blocked After the pair up the Master will enter search mode so press the Search button to go back to Standby mode b Under Standby mode the Master s LEDs will blink every second However if the Master gets turned off and on again it will enter Search mode automatically If the Master cannot pair up with the Slave within 50 seconds due to blocked or out of range signals it will enter Standby mode and beep to indicate pairing failure due to loss of signal The search button can be pressed every 50 seconds for retrying pairings c Slave will beep when it s being tracked or when out of range Under Standby mode the Slave s LED will blink every second to indicate its battery is still healthy Important Please turn off the Master when not in use to save battery life the Slave will automatically go into sleep mode to save battery until the Master tries to pair up again Out of range or Loss signal a The Master will beep vibrate and blink it s LED for 20 seconds when out of range or loss of s
3. Pet Mini Tracker User Manual Front amp Rear View Master Slave Front Back Front Back Distance j Hanging hole for stra indication ging P Right LED Left LED Signal Status indicator Long Distance Mute Button Short Distance Search Button Hanging hole Power off for strap Clip Signal Indicator Battery cover Pet Mini Tracker 505P Alert amp Search 0 200m 656ft Short Distance 25 10m 82 32ft Long Distance 50 10m 164 32ft Master MO5AM x1 Slave S05 x1 LR44x2 LR1130x2 30 days 8hrs 30 days 8hrs Over 90 days Over 90 days 95db 3 db 75 3 db Vibration Motor 52 8x39x13 2mm 2x1 6x0 52inch 19x29x7 9mm 0 7x1 1x0 3inch Dimension L W H Package Contents Suggested Setting place Model Name 505P Master Slave Master Unit 1 set ZAKS OPO amp Batteries pane LY LR1130x2 ak SS User manual v JA Strap Silicon Sleeve 1 1 Getting Started 1 For first time usage please insert the batteries into the Master as shown accordingly to the installation instructions below The Slave is already fitted with batteries simply pull the plastic tag out to activate Use instructions below for battery replacements in the future Master Slave 1 Open from the fillister on the button of housing or curve side by your nail like open shell 2 Insert batteries included following the polarity markings in the battery compartment 3 Close the battery com
4. he distance may be short depends on the 3 terrain environment x Search Tip a While searching always place the Tracking in front of you pointing forward Turn slowly around you following the direction indicator Once pointed at the right direction more LED s will be shown and the Melody tone will increase rapidly b If the distance between the Master and Slave is out of detectable range and becomes undetectable The Master will then beep every second to remind you to keep searching c Press the Search Button on the Master again if you would like to stop searching d While in search mode the Slave makes a low beeping sound every second This can assist you in finding its location via sound when near by Suggestion Press and hold the mute button on the Master to listen for the Slave s beeping sound During Search ANI Do not sway Master always make sure its in forward position when turning and searching Holding Way x lt To Correct Wrong Holding Holding Veo Do not cover the Master Alert If the Master makes a high frequency beeping tone and starts vibrating it means the distance between the Master and the Slave is over the set alert distance Check the specification for Alarm distance settings s ES Alarm from Master and Slave 25 10m short distance r Stop alarm beep if both devices 50 10m long distance comes within safe range again Ove Distance
5. ignal is detected the Master will then go into sleep mode automatically if it cannot detect the Slave b The Master will then beep once every two minutes to notify the user no Slave has been paired c To pair up or find the Slave with the Master press the search button to go to wake up process d The Slave s LED blinks for 20 seconds and goes into sleep mode when not paired Low battery When the Master and Slave unit is under low battery mode it will beep in a interval of every 2 minutes interval please change the battery Important Under low battery mode abnormal function will occur and the units may not function properly Please Note a The connection range is based on a clear line of sight Actual range will vary depending on usage environment and location b When the Master and Slave units are turned ON it takes 8 to 15 seconds for the synchronization c The disconnection alarm from the Master unit will sound every 2 minutes after disconnection of 30 seconds for power saving purposes Care and Maintenance a Keep the device dry Precipitation humidity and all types of liquids moisture can contain minerals that may corrode electronic circuits If your device gets wet remove the battery and allow the device to dry completely before replacing b Do not use or store the device in dusty dirty areas as its moving parts and electronic components can be damaged c Do not store the device in hot areas High temperature
6. io TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept an interference received including interference that may cause undesired operation FCC Caution Any changes or modifications are not expressly approved by the party responsible for compliance which could void the user s authority to operate this equipment EU Declaration Conformity This product is carrying the CE Mark in accordance with the related European Directives C 91E 02B1 U50G612
7. partment cover as shown 1 Slide out the battery cover 2 Insert batteries included following the polarity markings in the battery compartment 3 Close the battery compartment cover as shown 2 On the back of the Master Switch to the desired distance detection setting on the back as shown in the diagram It will now start pairing with the Slave assuming both units are on Once it beeps and flashes simultaneously press the Search Button it is now paired and in Stand by mode 3 Place the Slave into the provided silicon case and strap with the provided velcro strap through the two ventilation cuts at the back of the silicon case 4 Now Strap the Slave onto the Pe s collar using the Velcro strap IMPORTANT Leave Slave on the back of the Pet s neck facing up for best reception detection Search Under Standby mode press the Search button once on the Master The LED Signal statuses will start blinking left and right as it tries to link up with the Slave to find it s approximate position When the Master links up it will show the signal strength and direction via the LED indicators as well as via Sound The closer the Master is to the Slave the more rapid the beeping sound and LED signals Use the LED indicator and the sounding melody to help you track down the Slave T i Press and GO Oy A release z LN a O m ES be 22 cme i 00000 a va gt H o working range 0 200m 656ft line of sight E t
8. s can shorten the life of electronic device damage Batteries and warp or melt certain plastics d Do not store the device in cold areas When the device returns to its normal temperature moisture can from inside the device and damage electronic circuit boards e Do not attempt to open the device other than as instructed in this guide f Do not drop knock or shake the device Rough handling can break internal circuit boards and fine mechanics g Do not use harsh chemicals cleaning solvents or strong detergents to clean the device h Do not paint the device paint can clog the moving parts and prevent proper operation i Do not put the Master and Slave away as it s made to stay with your loved Pets j Search detection and alarm range will depend on the terrain environment k If the beeping sound is not loud enough the batteries may be getting flat Change to new batteries for louder alarm sounding This product only assists in providing a warning alarm to remind the user It does not guarantee to prevent theft or robbery of personal property m If you want to use the device during flight trips please comply with the flight safety law according to each country n We reserve the right in changing the specification of the hardware and software designs to manuals at any time and without prior notice Information in this document is subject to change without notice o This product operational temperature is between 32
Download Pdf Manuals
Related Search