Film Imaging Digitizer User's Manual
Contents
1. 3 Insert and push down both sides of the AFF into its compartment holes making sure the AFF snaps into place Medi 6000 Plus User s Manual 43 4 Plug the connector of the AFF into the digitizer s 9 pin accessory port securely and properly 44 Medi 6000 Plus User s Manual Positioning the X ray Films The AFF can hold up to 15 sheets of X ray films at a time This section shows you how to position X ray films into the AFF Tray correctly 1 Install the AFF onto your digitizer before using it Refer to the previous sections Installing and Connecting the AFF for the detail 2 Lift up the Top Rollers P a TDO AFF Tray Rear Roller Medi 6000 Plus User s Manual 45 3 Load the films into the AFF Tray with the side to be scanned facing up and with the top of the film directing upwardly When loading the films into the tray make sure all films have been loaded on the bottom rail of the AFF Tray Incorrect positioning of films may cause film jams or damage the digitizer Bottom rail Please take note that the bottom of the films should be placed against the front side of the bottom rail as shown in the graphic and rest the back against the AFF housing 46 Medi 6000 Plus User s Manual 4 Lower down the Top Rollers onto the films so the films are sandwiched between two sets of rollers Top Rollers and Rear Rollers Before start using the AFF to scan maker sur2. No 6 Industry East Road 3 RB BRANT Mee Pus Sclonco Based Industrial Park peper si 5 TYPE MSS S00KU2LAF 0120 india Taman NE anons E NEUEN angan re neasa aue oe CHOC nam a ELECTRIQUE NE PAS TAR Gm Unselessate 127 129 Sach PLRUROSRAT CC R SaR D 41877 Wilich Germany BEME H ASR IXSRAUMUSREIXRIHON 0120 Made in china nea XXI 147 011523 5 CE 0120 label TFDA label Power label for Taiwan shipping only MIC or MIT This label indicates that when an emergency situation happens turn off the power switch immediately Medi 6000 Plus User s Manual 9 On The Package Carton Bh h eci sooor s MICROTEK A 0120 t Carton label Carton label for EU US AP shipping for Taiwan shipping Fragile handle with care Keep in a dry place Keep away from magnets Store 3 boxes in one pallet Transport and storage directions 10 Medi 6000 Plus User s Manual Table of Contents Preface eer tinruieoIRIRiD eii 4 RR RR ARR R AI eR SIR alare siii 2 Safety Regulations iic o erronea uou oa rie Yr oa e IE ok nun EoR EN RAPRR Rae PR PNE inni 3 sre 3 Guidance and Manufacturer s Declaration for EMC Directive 4 CE Declaration of Conformity CE DOC eee eee
3. brighten and the digitizer is ready to scan Power switch 28 Medi 6000 Plus User s Manual Digitizing Your X ray Film Positioning Your X ray Film Medi 6000 Plus s Feed Tray can hold only one piece of X ray film at a time This section shows you how to position a single sheet of X ray film into the Feed Tray 1 Install the Feed Tray onto your digitizer before using it Refer to Feed Tray the front sections Installing the Feed Tray for the detail 2 Load and insert the film into the Feed Tray with the side to be scanned facing up and with the top of the film directing upwardly Push the film into the tray until the edge of it touches the bottom edge of the Feed Tray 3 Align the film with the center of the Feed Tray by sliding the two Guide Arms toward the film if the width of the film is less than 14 inches Guide A Medi 6000 Plus User s Manual 29 Note There are several precautions and reminders about using the digitizer correctly Please refer to the section as below for the detail e The Feed Tray can handle X ray films of the following sizes Width 2 5 to 14 63 5 to 355 6 mm Length 2 5 to 35 63 5 to 889 mm Sheet Feed Single sheet per time e fthe film are torn curled or wrinkled do not put them into the Feed Tray to scan because they may cause film jams e Remove clips or staple
4. 6000 Plus User s Manual 41 C Optional Auto Film Feeder AFF The Auto Film Feeder AFF is an optional accessory for the Medi 6000 Plus digitizer The AFF only works with X ray film allowing to hold up to15 sheets of the X ray film automatically at one time It increases convenience and efficiency in multiple sheet scanning of X ray film Microtek recommends that the digitized images came from the use of this accessory are intended for the use in primary secondary and over reading applications This device is not to be used for primary image diagnosis in mammography Also it is specifically designed for the trained medical professionals or staff The coming section describes how to install the AFF on the Medi 6000 Plus through the Medi 6000 Plus s accessory port and how to scan X ray films by using the AFF 42 Medi 6000 Plus User s Manual Installing the Auto Film Feeder AFF You can use either the Auto Film Feeder or the Feed Tray for one time with your digitizer therefore before mounting the AFF onto your digitizer make sure that the Feed Tray has been removed out from the digitizer and the digitizer s power is off Lift up the Feed Tray and remove it from the digitizer before installing the AFF onto the digitizer Follow the steps below to install the AFF 1 Unpack the AFF 2 Look for two sets of the Feed Tray Holes at both ends of the front top of the digitizer
5. X ray Film x100i rece ne cene eee eee eee 29 Positioning Your X ray Film mm emen 29 Using ScanWizard Medi sss mene nemen nenne 31 Scanning X ray Films in Auto Scan Mode cecer 31 A Scanning with Default Settings esee 31 B Scanning with Customized Settings sssesssss 33 Scanning X ray Film in Smart Scan Mode secese 35 Care and Cleaning esee cese o eoa oa TTT 37 Cleaning the Glass Surface L Li 37 Cleaning the DIfTUSOr 2er etna tkt dnx red ixn x ee 38 Cleaning the Rollers cei ener d tke tane niodo cim sa Lern tania dn EN en 38 Maintenance iaia aaa s liiiei EAR RicrEIeR RER A EERR Rene 39 Appendici indivi 40 A Fixing Film Jarris oec ved cns e teretesiea deni enn attain vite dunt nne e mdi a ise 40 B Troubleshooting iaia 41 C Optional Auto Film Feeder AFF seseseeeme 42 Installing the Auto Film Feeder AFF esee 43 Positioning the X ray Films mme 45 Scanning X ray Films using the Auto Film Feeder AFF 48 D Specifications cire rece aero iii ia ci 50 12 Medi 6000 Plus User s Manual Knowing aboutYour Film Digitizer The Medi 6000 Plus is a sheet fed transparency film digitizer that can easily transfer radiographs and x ray films into a digital format The digitized images are intended for the use in primary second
6. abrasive lint free cloth clean the inner glass surface on the digitizer Medi 6000 Plus User s Manual 37 Cleaning the Diffuser The diffuser is used when you scan a X ray film or transparent material The cleanness of the diffuser decides whether your digitizer may deal with the right lightness of scanned transparent materials To clean the diffuser 1 Push down two buttons at both sides of the front cover of the digitizer and open the front cover When opening the front cover support the both sides of the front cover with your hands avoiding suddenly falling down of the front cover 2 Use the same kind of cloth for cleaning the digitizer glass surface to clean the white diffuser located at the middle of the front cover Cleaning the Rollers Prolonged used of the digitizer may result in accumulation of ink and other residue on the feeder s rollers affecting their efficiency Clean the rollers periodically to maintain performance Rollers are found in two areas of the Medi 6000 Plus Directly on the digitizer and on the side of the front cover To clean the two sets of rollers 1 Push down two buttons at both sides of the front cover of the digitizer and open the front cover When opening the front cover support the both sides of the front cover with your hands avoiding suddenly falling down of the front cover 38 Medi 6000 Plus User s Manual 2 Clean the rollers with a lint free cloth or a swab
7. or disconnecting the cables A A e Insert the plug completely into the outlet as a loose connection may cause arcing and result in fire e Ensure to hold the plug or connector to disconnect the cable otherwise if you pull the cable only it may damage the core wire and result in fire or electric shock A e Place and route the power supply cord such that it is not likely to be walked on or pinched by items placed upon or against them paying particular attention to the cord near the power plugs convenience receptacles and at the point where it exits from the outlet A e When the digitizer is left unattended and unused for long periods of time unplug it from the wall outlet Moving and Storing the Film Digitizer A e Always ensure that the digitizer is stored properly before shipping or moving it Quick stops excessive force and uneven surfaces may cause the product to overturn when moving A A e Do not hit or drop the digitizer The digitizer may be damaged if it receives a strong jolt which may result in fire or electric shock if the digitizer is used without being repaired A e Do not place the digitizer on any slippery slanted or unstable surface The product may slide or fall causing serious injury to people as well as serious damage to the product Medi 6000 Plus User s Manual 7 A A e Do not use the digitizer near water Never spill liquid of any kinds on the product or it may result in electric shock or oth
8. Cord PN EU 121 46 032005 cD PN US 121 46 500000 PN 141 016511 Hi Speed USB Cable PN TWN 121 46 570000 PN 121 44 150504 _ gt ii A 18 Medi 6000 Plus User s Manual Output Basket PN 141 014482 Medi 6000 Plus User s Manual 19 How to Repack Your Film Digitizer for Shipping To ship back your Medi 6000 Plus for repairing maintenance services or other reasons in order to not damage your Medi 6000 Plus it is strongly recommended that using the original carton and other packing materials Follow the steps below to repack your Medi 6000 Plus correctly 1 Wrap the digitizer with the plastic bag and then insert it into one foam support gt WS 2 Cover down the other foam support on the tops of the digitizer 20 Medi 6000 Plus User s Manual 3 Turn over the foam supports and make it stand horizontally 5 With both hands hold the two sides of the scanner machine body with the foam soupports and then insert them into the shipping carton Put the accessory box at the top of the scanner Finally close the top cover of the shipping carton and seal it with tape Medi 6000 Plus User s Manual 21 Taking a Closer Look Front Top Bottom View No Names of Parts Functions of Parts 1 Feed Tray Holes Uses to hook the Feed Tray onto the digitizer 2 Power Switc
9. GHz Rated maximum output power of transmitter w SNF da WP d t LP V E E 0 117 017 0233 0369 amp 0369 02738 11607 1107 2333 J 36900 amp 36900 737 11 667 11667 23 333 For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer NOTE 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people The ME declaration electromagnetic immunity 1 The ME system is intended for use in the electromagnetic environment specified below The customer or the user of the Model 006 should assure that it is used in such an environment Immunitytest IEC 60601 TestLevel Compliance level Electromagnetic environment guidance Conducted RF 3 Vrms Portable and mobile RF communications equipment IEC 61000 4 6 150 kHz to 80 MHz should be used no closer to any part of the ME EQUIPMENT or ME SYSTEM including cables than the recommended separation distance calculated Radiated RF 3 Vim from the equ
10. MICROTEK ff Medi 6000 h5 Film Imaging Digitizer User s Manual www microtek com Preface Copyright 9 2013 Microtek International Inc all rights reserved This document may not be reproduced or copied in any way stored electronically or translated into any language without the permission of Microtek International Inc Trademarks Microtek ScanMaker ArtixScan ScanWizard and ColoRescue are trademarks or registered trademarks of Microtek International Inc All other trademarks or registered trademarks are the property of their respective holders Specifications software and hardware bundles are subject to change without notice Not responsible for typographical errors Disclaimer The contents of this manual have been checked carefully for accuracy and every effort has been made to ensure that there are no errors However Microtek makes no guarantee as to the accuracy of the contents of this document and reserves the right to make changes to the contents without prior warning 149 004924 B September 2013 Microtek International Inc No 6 Industry East Road 3 Science Based Industrial Park Hsinchu Taiwan EVESTAR GmbH D 47877 Willich Germany Microtek International Inc 6 Industry East Road 3 Science Based Industrial Park Hsinchu Taiwan Tel 886 3 5772155 Fax 886 3 5772598 http www microtek com 2 Medi 6000 Plus User s Manual CE 0120 A CE 0120 Compliant Device FDA 510
11. USB USB 2 0 port Hi Speed USB USB 2 0 is capable of high data transfer rates of up to 480 Mbit sec e Easy to operate clean and maintain The Medi 6000 Plus requires virtually no routine maintenance and no daily cleaning which is ideal for busy radiology departments e Microtek ScanWizard Medi software The friendly user interface of ScanWizard Medi stores X ray pictures in a computer readable format offering an easy and quick access and management Auto scan With this feature the Medi 6000 Plus automatically performs a scan job once when it detects a X ray film put on the Feed Tray No matter a novice or an expert can start scanning immediately Medi 6000 Plus User s Manual 13 Auto crop This feature automatically detects the size of the original image crops the full scan frame to fit the image and removes unwanted black borders Auto density This feature enables the digitizer to optimize the image density automatically when scanning a X ray film It automatically defines the lightest and darkest pixels in a scanned image and then redistribute the intermediate pixel values proportionately Customized exposure This manual setting tool allows you to customize an exposure time for the scanned image It enhances the visibility of extreme dark film delivering a better scanning result and improving the quality of saved files System Requirements In order to use your Medi 6000 Plus your comput
12. ary and over reading applications This device is not to be used for primary image diagnosis in mammography Also it is specifically designed for the trained medical professionals or staff The Medi 6000 Plus can capture details in bright and dark areas of x ray films and provide the medical professionals a convenient method to digitize the roentgenogram for the electric data storage Features of the Medi 6000 Plus The Medi 6000 Plus comes with several important features including the following e Premium Image Quality With a high optical resolution of 600 dpi a dynamic range of 4 0 Dmax and the 16 bit grayscale the Medi 6000 Plus allows users to get better image details in just seconds e Energy saving LED light source Adopting LEDs as the light source when the digitizer is detected by the system there are no requirements for any warm up time before carrying out the scan which boots your productivity and reduces energy costs amazingly With its stable performance the image quality will remain consistent even after used for a certain period of time e Various sizes of x ray films The Medi 6000 Plus covers various sizes of sheets or x ray films from 2 5 x 2 5 to 14 x 35 which offers more flexibility to digitize old records or x ray films e Ultra high scanning speed The Medi 6000 Plus increases your productivity with fast scanning speed which is less than 12 seconds at 300 dpi for grayscale scans e Hi Speed
13. ation applicable to the frequency of the IEC 61000 4 3 80 MHz to 2 5 GHz transmitter Interference may occur in the vicinity of equipment marked with the following symbol 4 Medi 6000 Plus User s Manual The ME declaration electromagnetic immunity 2 the Model 006 should assure that it is used in such an environment i Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 95 Mains power quality should be that of a typical commercial or hospital environment 1kV line s to x Mains power quality should be that of a line s typical commercial or hospital 2kV line s to earth environment Mains power quality should be that of a typical commercial or hospital environment If the user of the Model 004 image intensifier requires continued operation during power IEC 61000 4 11 mains interruptions it is recommended that the Model 004 Image Intensifier be powered from an uninterruptible power supply or a battery gt 95 dip in Ur for5s If image distortion occurs it may be necessary to position the Model 004 image intensifier further from sources of power frequency magnetic fields or to install magnetic shielding The power frequency magnetic field should be measured in the intended installation location to assure that it is sufficiently low The ME declaration electromagnetic immunity 3 The ME system is intended fo
14. e that the Output Tray i e Output Basket has been installed correctly on your Medi 6000 Plus too otherwise improper outputs of piles of films may cause jams of films and bring damage to your digitizer Refer to the previous section Installing the Output Tray for the details about how to assemble the Output Tray onto your Medi 6000 Plus Medi 6000 Plus User s Manual 47 Scanning X ray Films Using the Auto Film Feeder AFF 1 Load the films to be scanned into the AFF Tray 2 Launch ScanWizard Medi either as a stand alone by clicking the program icon on the desktop or by using the File Import or Scan command from an application program Smart Scan 3 Activate the Auto Film Feeder mode Auto Scan w Auto Film Feeder In the Preview window click and hold the arrow on the Auto Scan button then choose Auto Film Feeder from its option menus 4 Select your image output type as Gray Scale Gray Scale 12 bit or Gray Scale 16 bit from the Type drop down menu 5 Select your desired image output resolution in the Resolution drop down menu The recommended resolution is 300 dpi or above 6 Specify your scan frame to meet your X ray film size by using the Scan Frame tool button in the Preview window and then resize the size of the scan frame by dragging on the edge or corner of the scan frame 7 f necessary use the Window Expansion button to enable the image correctio
15. e by clicking the program icon on the desktop or by using the File Import or Scan command from an application program Make sure the Auto Scan Mode has been activated If not click and hold the arrow on the Smart Scan button in the Preview window then choose Auto Scan from vA its option menus Select your image output type as Gray Scale Gray Gray Scale Scale 12 bit or Gray Scale 16 bit from the Type v Gray Scale 12 bit drop down menu Gray Scale 16 bit Select your desired image output resolution in the Resolution drop down menu The recommended resolution is 300 dpi or above Specify your scan frame to meet your X ray film size by using the Scan Frame tool en button in the Preview window and then resize the size of the scan frame by dragging on the edge or corner of the scan frame If necessary use the Window Expansion button to enable the image correction tools to EE TI M adjust image quality Type Gray Scale 12 bit Resolution 200 gt For example Scan Frame x Scaling Output wpa _ um uam EN rg E Enable auto density function from the Density drop down menu ingens SN Specify a customized Exposure Time in in A the Exposure Time drop down menu Reset Load the film to be scanned into the Feed Tray and the digitizer will start scanning automatically After loading the film the digitizer starts to detect for the film automatically O
16. eee e eee e eee ee enee 6 Safety Precautions ua IRR ARIA RP E E ERE IARE 7 Labels and Markings 2 rt arrepta aa n REG ES 9 O Th bI 19 On The Package Carton eerta kan aa a 10 Knowing about Your Film Digitizer ee 13 Features of the Medi 6000 Plus sese 13 System Requirements Li 14 Unpacking Your Film Digitizer s s s 1 s s00 ricci 15 Looking for Darmiage ize see Exe d retos ai gates 15 Unpacking Package Contents sssessssssee mme 15 Package Contents a a siae prse e nu pra eI PEN 16 How to Repack Your Film Digitizer for Shipping 0 20 Taking a Closer Look 1 s srrriei iii iii 22 Front Top Bottom View meme rennes 22 R at Side VIEW seisis rennen tenian cie usd e LR pira 23 Assembling Your Film Digitizer eeeeeeeeeeeeeeeeee 24 Installing the Feed Tray i 24 Installing the Output Tray cece eect teeters neta eee eee ee nae 25 Installing Your Film Digitizer Leere eres 26 Installing the Software alia iii 26 Connecting the Film Digitizer esee 27 To the Power CORD sce eene menn nnnm cene tef eed e d Ra 27 To the Hi Speed USB Cable sess 27 Medi 6000 Plus User s Manual 11 Digitizing Your
17. er hazards IN e This digitizer should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat IN e Do not store the digitizer in which it may be exposed to direct sunlight Using the Digitizer A e Before using the digitizer make sure the area of the front cover is clear from any objects that may cause jams inside IN A e When using the digitizer if your hairs have been jammed into the front cover of the digitizer turn off the power switch immediately Do not attend to remove your hairs from the front cover when the digitizer is still turned on Maintenance and Service e When the digitizer is going to be cleaned ensure to turn off the power of each device and unplug the power cable from the AC outlet e When you need a repair service unplug the digitizer from the power outlet and consult qualified service personnel When replacement parts are required use replacement parts that are specified by the manufacturer or have the same characteristics as the original parts D pe wp e For safety reasons ensure to inspect the device before using it In addition carrying out a regular inspection at least once a year 8 Medi 6000 Plus User s Manual Labels and Markings On The Device n MICROTEK A canon A C Microtek International Inc BABS SA RX To pr trical do
18. er must satisfy the following system requirements CD ROM drive for installing software Color display with 24 bit color output capability 512 MB RAM or above Pentium IV PC or higher with Hi Speed USB USB 2 0 port Microsoft Windows XP Vista Windows 7 or Windows 8 14 Medi 6000 Plus User s Manual Unpacking Your Film Digitizer Looking for Damage While unpacking your digitizer inspect the shipping carton for any signs of mishandling or damage The digitizer s packing carton and padding material have been carefully chosen to prevent damage to the unit in shipping and can withstand a reasonable amount of pressure After unpacking your digitizer package refer to the later section to ensure that you received all of the parts necessary for digitizer setup If there are any damaged or missing parts notify the shipper immediately or contact customer service NOTE Save the carton and all packing materials If you need to ship the digitizer later it is recommended that you should repack it using the original wire ties plastic bags foam supports and cartons which protects your digitizer from unnecessary damage Refer to the later section How to Repack Your Film Digitizer for Shipping for the detail Unpacking Package Contents After unpacking the shipping carton follow the steps shown below to take out your digitizer and other accessory components 1 Ensure that you put your shipping carton toward the right directi
19. h Turns the digitizer on or off 3 Front Cover Uses to cover inner components of the digitizer 4 Green Orange LEDs Indicates the status of the digitizer For more details refer to the Troubleshooting section of this manual 5 Output Tray Holes Uses to hook either the Output Guide or the Output Basket onto the digitizer 6 Release Buttons Releases the front cover to open the lamp holder There are two Release buttons located on each side of the front cover Press the buttons down simultaneously to release the front cover 22 Medi 6000 Plus User s Manual Rear Side View No Names of Parts Functions of Parts 1 Hi Speed USB Port Connects the Hi Speed USB 2 0 cable to the computer Power Connector Connects the digitizer to the power cord AFF Connector Connects the Auto Film Feeder AFF to the digitizer Medi 6000 Plus User s Manual 23 AssemblingYour Film Digitizer Installing the Feed Tray Coming with your digitizer there is a separated Feed Tray which holds the X ray films to be fed into the digitizer Before using the Feed Tray with your digitizer you need to assembly it onto the digitizer Follow the instructions and graphs below to correctly install the Feed Tray 1 Look for two sets of the Feed Tray Holes at both ends of the front top of the digitizer 2 Insert and push down both sides of the Feed Tray into its compartment holes
20. hu Taiwan 30077 R O C Declares that Type of Equipment Medical Image Digitizer Model Number MSS 600XU2LAF Complies with following Standard Directive IEC60601 1 2005 CORR 1 2006 CORR 2 2007 93 42 EEC EN 60601 1 2 2007 93 42 EEC Emissions ENS5011 2007 A2 2007 Group 1 Class B EN 61000 3 2 2006 A2 2009 Class A EN 61000 3 3 2008 Immunity IEC 61000 4 2 Ed 2 0 2008 IEC 61000 4 3 Ed 3 2 2010 IEC 61000 4 4 Ed 2 1 2011 IEC 61000 4 5 Ed 2 0 2005 IEC 61000 4 6 Ed 3 0 2008 IEC 61000 4 8 Ed 2 0 2009 IEC 61000 4 11 Ed 2 0 2004 Declared by Derek Tang Name Surname R amp D center Vice President Position Title Derek i amg Legal Signature Hsinchu Taiwan 02 04 2013 Place Date 6 Medi 6000 Plus User s Manual Safety Precautions Before using your digitizer read the following safety guides carefully which detail the proper operation of the digitizer and its accessories to prevent injuries or damage to users or equipment Meanings of Symbol Signs This indicates hazardous situation which if not payed CAUTION attention could result injury or damage to users or equipment J This indicates hazardous situation which if not payed WARNING attention could result serious injury or death to users Power Supply A e Use a power source only with a power rating specified on the marking label A A e Ensure to turn off the power of each device before connecting
21. ions Scanner Type Model Type Light Source Scanning Modes Resolution Scanning Area Film Size Lamp Life Product Life Cycle Interface Dimensions L x W x H Weight Voltage Power Consumption Environment Important Sheet feed film digitizer MSS 600XU2LAF LED Light Emitting Diode Grayscale in a single scanning pass Input 8 bit grayscale Approx 256 shades of gray 16 bit grayscale Approx 65 536 shades of gray Output 8 bit grayscale Approx 256 shades of gray 12 bit grayscale Approx 4 096 shades of gray 16 bit grayscale Approx 65 536 shades of gray 600 dpi 14 x 35 355 6 mm x 889 mm Min 2 5 x 2 5 63 5 mm x 63 5 mm Max 14 x 35 355 6 mm x 889 mm 1 000 000 scans at 300 dpi 100 000 scans or 5 years Hi Speed USB USB 2 0 10 2 x 18 7 x 9 3 260 mm x 474 mm x 235 mm 19 82 Ibs 9 kg AC 100V to 240V 47 63 Hz 1 5A Max Input 54 9 W Max Operating temperature 50 to 104 F 10 to 40 C Relative humidity 2096 to 8596 Storage temperature 14 to 140 F 10 to 60 C Relative humidity 2096 to 9596 Atmosphere pressure 70 101 3 kPa 700 1013 hPa Altitude 22000 m Specifications software bundles and accessories are subject to change without notice Not responsible for typographic errors 50 Medi 6000 Plus User s Manual
22. k Certification 510 k Number K091288 Taiwan FDA Certification Certified Number 003518 WEEE Compliance Statement Microtek International Inc operates under full compliance with the WEEE Directive Among the requirements of the Directive are the marking of any applicable equipment placed in the EU market with the WEEE symbol a crossed out wheeled bin as shown at left demonstration of the implementation of a take back program and meeting recycling targets ISO Compliance Statement Comply with the requirements of the international standard ISO 9001 2000 and ISO 13485 2003 Medi 6000 Plus User s Manual 3 Guidance and Manufacturer s Declaration for EMC Directive For EQUIPMENT or ME SYSTEM that are not LIFT SUPPORTING Recommended separation distances between portable and mobile RF communications equipment and the ME EQUIPMENT or ME SYSTEM The ME EQUIPMENT or ME SYSTEM is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of the ME EQUIPMENT or ME SYSTEM can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the ME EQUIPMENT or ME SYSTEM as recommended below according to the maximum output power of the communications equipment Separation distance according to frequency of transmitter m 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5
23. ll On Ready to scan Green LED Orange LED First make sure that you have followed steps as described in the Assembling Your Film Digitizer section of this document Then if your problem is listed here try the suggested solution 1 No light comes on when the digitizer is turned on Make sure your digitizer is connected to your computer and plugged into a power source 2 The Add Remove Hardware Wizard appears on your screen Click the Cancel button and close the ScanWizard Medi scanning software Disconnect the Hi Speed USB cable from your computer and refer to the installation instructions in this document 3 When trying to scan an error message appears on your screen that reads Can t Find Scanners Make sure your digitizer is connected to your computer and plugged in to a power source see Connecting the Digitizer in the Assembling Your Film Digitizer section Uninstall and reinstall the ScanWizard Medi software 4 After clicking Scan a blank screen appears Uninstall and reinstall the ScanWizard Medi software 5 When trying to scan an error message appears on your screen that reads Code 204 Scanning lamp or image sensor circuit failure Please don t select fast preview or draft scan This error message appears when the luminance of lamps is insufficient or surpassed Click OK first then contact the professional technician for the further help Medi
24. making sure the Feed Tray snaps into place Feed Tray Feed Tray Holes 24 Medi 6000 Plus User s Manual Installing the Output Tray Coming with your digitizer there are two kinds and separated Output Trays which store the stacked x ray films which have been digitized One of them is called Output Guide used to guide the digitized materials staying on the table The other is called Output Basket used to store and keep the digitized materials in a basket You may use only one of them as an output tray at a time Before using them with your digitizer you need to assembly them onto the digitizer 1 Look for two sets of Output Tray Holes at both ends of the front bottom of the digitizer 2 Insert and push down both sides of the Output Guide into its compartment holes making sure the Output Guide snaps into place Or Insert and push down both sides of the Output Basket into its compartment holes making sure the Output Basket snaps into place Output Guide Output Basket Medi 6000 Plus User s Manual 25 Installing Your Film Digitizer Installing the Software Important You must install software before connecting your digitizer Always close any open programs and turn off Anti virus utilities before installing software 1 Turn on your computer 2 Place the Microtek CD into your CD ROM drive 3 Follow the on screen instructions to install the dri
25. moistened with alcohol or ECO cleaner as shown in the graphic below Remember to clean the rollers on the digitizer and the front cover at the same time Rollers on the digitizer Rollers on the front cover of the digitizer Maintenance After usage for a period of time the parts inside your digitizer such as rollers or light source may become worn out and a problem such as insufficient light supply may occur In this cases contact your local dealers or wholesales for the maintenance services Note Your digitizer need a professional to perform the required service or maintenance Do not attend to fix or perform the maintenance by yourself or it may cause dangers to you or the digitizer Medi 6000 Plus User s Manual 39 Appendix A Fixing Film Jams 1 Open the front cover by pressing the Release buttons on the both sides of the front cover 2 After opening the front cover let the jammed film fall into the output basket and then remove it from the output basket Note To remove the jammed film from the digitizer you have to open the front cover first Otherwise your film may be damaged if they are forcedly removed 40 Medi 6000 Plus User s Manual B Troubleshooting The LEDs on the front right panel of the digitizer indicate the status of the digitizer C LL At Off Digitizer is off i Flashing Orange Starting up the L scanning Lid L Orange off Scanning L BI 7 A
26. mport or Scan command from an application program 2 Make sure the Auto Scan Mode has been activated If not click and hold the arrow on the Smart Scan button in the Preview window then choose Auto Scan from its option menus 3 Load the film to be scanned into the Feed Tray When the film is detected by the digitizer the ScanWizard Medi will automatically recognize auto crop and perform a scan of the film and save it in your preferred folder or application e f ScanWizard Medi is launched as a stand alone program the scanned image can be saved to a file or opened in an image editing program To view the scanned image double click the MSmart Images icon on your desktop e f ScanWizard Medi is launched as a Plug In from an image editing program the scanned image is delivered to your application where the image can be saved printed or modified further Medi 6000 Plus User s Manual 31 ysibug Untitled1 bd Gray Scale 12 bit v x0 fell mi o7 Eu 100 v po inch v Ne os ome X Settings window Auto Scan mode 2 fagnify Pan Overview Preview window 32 Medi 6000 Plus User s Manual B Scanning with Custom Settings If this method is selected a scan job will be carried out automatically with customized settings These customized settings can be adjusted or selected in the Settings window 1 Launch ScanWizard Medi either as a stand alon
27. n tools to adjust image quality For example Enable auto density function from the Density drop down menu Specify a customized Exposure Time in the Exposure Time drop down menu 8 Click the Auto Film Feeder button in the Preview window to scan all the films loaded on the AFF Tray e If ScanWizard Medi is launched Microtek ScanWizard Medi Scan To Save As as a stand alone program a Save in C3 My Images window Stan To Save As oa dialog box will appear Click the qu Save button then the scanned A Image004 tif To Image005 tif image can be saved into your selected folder or sent to your selected application Tis seed Save as type Tagged Image File Format tif M Cancel To view the scanned image m double click the MSmart Images r e icon on your desktop default Send image to application ater saving folder assigned by the software E Adobe Photoshop or retrieve it from your assigned folder e If ScanWizard Medi is launched as a Plug In from an image editing program the scanned image is delivered to your application where the image can be saved viewed or modified further 48 Medi 6000 Plus User s Manual Gray Scale 12 bit v o Fl si cl favo um Foo Lee Verview vs No Correction No Correction db Custom Settings window Preview window Medi 6000 Plus User s Manual 49 Specificat
28. nce the film is detected the ScanWizard Medi will automatically recognize auto crop and perform a scan of the film and save it in your preferred folder or application Medi 6000 Plus User s Manual 33 ysibug Untitled vi Gray Scale 12 bit M LN LN Foe ara ce No Correction ie No conection f NoCorecion emm 200 p ___v EM Verview 34 Medi 6000 Plus User s Manual Scanning X ray Films in Smart Scan Mode In the Smart Scan mode ScanWizard Medi will automatically recognize auto crop and perform a scan of the film after the Smart Scan button is pressed 1 2 Load the film to be scanned into the Feed Tray Launch ScanWizard Medi either as a stand alone by clicking the program icon on the desktop or by using the File Import or Scan command from an application program Activate the Smart Scan mode v smart Auto Scan Auto Film Feeder In the Preview window click and hold the arrow at the right bottom corner of the Auto Scan button then choose Smart Scan from its option menus Follow the procedures steps 3 through 6 for Scanning with Customized Settings in the previous section to specify your scanning requirements Click the Smart Scan button to start scanning e If ScanWizard Medi is launched Microtek ScanWizard Medi Scan To Save As as a stand alone program a Save in My Images window Scan To Save A
29. on Then lift up the top cover Medi 6000 Plus User s Manual 15 2 Remove each cardboard from four sides of the shipping carton Sa SD 3 Take the accessory box at top out from the shipping carton f JL gt pd p Y S 4 With both hands hold the both sides of the scanner machine body and then lift up the scanner with foam supports firmly from the carton Before putting down the package on a steady surface do not go off either of hands from holding the foam supports Note The package of the contents is heavy almost 33 pounds Due to the heavy weight of the package about 33 pounds make sure you can handle it properly before removing it from the carton 16 Medi 6000 Plus User s Manual 5 Turn over the foam supports and make them stand vertically 6 Liftup the upper foam support 7 Pull out the digitizer from the bottom foam support Then remove the digitizer from the wrapped plastic bag Medi 6000 Plus User s Manual 17 Package Contents After you have unpacked your digitizer package please check for the major components listed below Accessory Box 219 31 500403 Medi 6000 Plus Film Digitizer I41 016546 NZ Feed Tray PN 215 21 360307 4 o l z Output Guide PN 141 015324 Power
30. r use in the electromagnetic environment specified below The customer or the user of the Model 006 should assure that it is used in such an environment Immunity test IEC 60601 Test Level 1 Electromagnetic environment guidance Dems 9 nmuertret Meat ctu ssomen maria CISPR 11 intended function Nearby electronic equipment may be affected i ME system must be used only in a shielded location with a minimum RF shielding effectiveness and for each cable that exits the shielded location a Harmonic emissions minimum RF filter attenuation of 80 dB from IEC 61000 3 2 10 MHz to 20 MHz 100 dB from 20 MHz to 80 MHz and 80 dB from 80 MHz Voltage fluctuations Applicable to 100 MHz The minimum at 20 MHz is 100 dB and the minimum at 80 MHz flicker emissions is 80 dB IEC 61000 3 3 The ME system when installed in such a shielded location is suitable for use in all establishments other than domestic and those directly connected to the public low voltage power supply network that supplies buildings used for domestic purposes Medi 6000 Plus User s Manual 5 CE Declaration of Conformity CE DoC Microtek International Inc I R TEK 6 Industry East Road 3 Tel 886 3 5772155 Science Based Industry Park Fax 886 3 5772598 Hsinchu Taiwan 30077 R O C DECLARATION OF CONFORMITY DoC Supplier Name Microtek International Inc Address No 6 Industry East Road 3 Science Based Industrial Park Hsinc
31. s Geral Zi Image tif dialog box will appear Click the E magan t Save button then the scanned EU image can be saved into your 8 ImageQ0s ti selected folder or sent to your selected application Filename My Images Save Save as type Tagged Image File Format tif xl Cancel To view the scanned image 3 double click the MSmart E E Images icon on your desktop default folder assigned by the software or retrieve it from your assigned folder Send image to application after saving E Adobe Photoshop e If ScanWizard Medi is launched as a Plug In from an image editing program the scanned image is delivered to your application where the image can be saved viewed or modified further Medi 6000 Plus User s Manual 35 ysibug Untitled b Gray Scale 12 bit hd LN ro fo ro era Lei vel women em No Correction vi 5 non J9 20000 gt 36 Medi 6000 Plus User s Manual Care and Cleaning To ensure optimal performance from the Medi 6000 Plus it is important to clean several critical parts of the digitizer on a regular basis Cleaning the Glass Surface 1 Push down two Release buttons at both sides of the front cover of the digitizer and open the front cover When opening the front cover support the both sides of the front cover with your hands avoiding suddenly falling down of the front cover 2 Using a soft and non
32. s before placing the film into the Feed Tray DO NOT use the digitizer to scan your X ray film with clips or staples because they may cause film jams or damage the digitizer 30 Medi 6000 Plus User s Manual Using ScanWizard Medi The ScanWizard Medi is a scanning software designed for the use of the X ray film scanning Its easy and user friendly interface enables you to easily start the scanning process Refer to the ScanWizard Medi software manual for more details The following sections will show you how to scan a X ray film by using the Medi 6000 Plus with ScanWizard Medi step by step Warning Do not place more than one piece of X ray film on the Feed Tray for doing so will damage the original film during the feeding process Scanning X ray Films in Auto Scan Mode The Auto Scan mode is the default scanning mode after the ScanWizrd Medi is launched at the first time enabling the Medi 6000 Plus detects the X ray film on the Feed Tray automatically and then perform a smart scan directly The Auto Scan mode is always displayed on the screen unless you switch the scanning mode to the Smart Scan mode To scan X ray films in Auto Scan mode using one of the following methods A Scanning with Default Settings If this method is selected a scan job will be carried out automatically with factory default settings 1 Launch ScanWizard Medi either as a stand alone by clicking the program icon on the desktop or by using the File I
33. ver and software NOTE If the Microtek Software Installer screen does not come up automatically double click the following in succession My Computer the CD ROM icon then cdsetup exe to start the installer program 4 Click EXIT on the Microtek Software Installer screen when all the software have been installed 5 Restart your computer Drivers amp Software Upgrades After you finish the installation of software if you found that the installed drivers and software cannot run your product or your computer system properly later please go to the Microtek Download Service site at ww7 microtek com tw service php to download and install any updates you may require For additional information about Microtek products please visit our website at www microtek com 26 Medi 6000 Plus User s Manual Connecting the Film Digitizer To the Power Cord 1 Connect the power cord to the left side of the digitizer 2 Plug one end of the power cord into a wall outlet or other power source To the Hi Speed USB Cable 3 Connect one end of the Hi Speed USB cable to your computer 4 Connect the other end of the Hi Speed cable to the digitizer s USB port locating at the left side of the digitizer Medi 6000 Plus User s Manual 27 5 Turn the power switch at the front left panel of the digitizer to On once the scanner is detected by your system the LED lights on the front panel will
Download Pdf Manuals
Related Search