User Manual
Contents
1. When the Host receives RF signal from Sensor the red light on the tire will extinguish one after one 4 Operation and Settings DD 4 1 Function Key and Set up Key Operation Functi NY Do not Showing battery power press Press Set temperature warning of tire once and the limited range is available from 60 100 C Press 2 Upper Limit settings of tire times pressure Bar H High right click can set value range from 2 8 4 2 Bar Press 3 Lower Limit settings of tire times pressure Bar L Lower and the range is available from 1 8 3 2 Bar DDH 4 2 Warnings and Legends Display on the Host Unit Tire Pressure Warning Legend When the tire pressure is too low or too high every 10 seconds prompted two short beeps for one minute and at the same time the tire pressure warning icon flashes Tire Temperature Warning Legend When the tire temperature is too high prompted two beeps every 10 seconds and for one minute Tire temperature alarm icon flashes Insufficient electricity power of tire warning Legend When individual tire pressure is less than 2 6 Volt the tire chartShown and the battery icon flashes and prompts every 10 seconds two short beeps for one minute and you can press the set button to enter the battery voltage view the tire and replace with new ones Please note When battery power of Sensor is less than 2 6 Volt Sensor will be unable to work which has influences on RF sig2. and paste its label on the Sensor LF L1 RF R1 1 Remove the plastic gas nozzle on the tire first and fasten it up with anti theft nut make sure Sensor s tire position labels are matched in tires positions then install and fasten them on the gas nozzle Figure 18 21 Precaution please must fasten sensor and gas nozzle it might have gas leakage if failed to do Figure 21 Figure 20 Step 4 Sensor Fasten up Instruction 1 Swivel the anti theft nut toward direction of the sensor Figure 22 2 Take the wrench to buckle anti theft nut with one hand and seize sensor with another hand to fasten up with each other inward Figure 23 24 3 Check if Sensor has been installed and fastened correctly K atl a M Figure 22 Figure 23 7 Figure 24 FAQ 1 After HUD is power on for 5 minutes it remains failure of receiving wireless signal unable to receive signal transmitted from 4 pieces of Sensor in 5 minutes Resolution 1 Please make sure if the batteries are in reverse Negative is poured at bottom side and positive at upper side 2 Please make sure the snap of battery is fastened and in close of the batteries Figure 25 26 3 Please make sure if voltages in the batteries are enough please replace with new ones if less than 2 6V 4 Please disassemble the battery replace the battery once 5 Please swivel the lid and check if penetration of any vapor occurred which
3. caused battery snap or rust and malfunction Please be sure to fasten up the lid and adhere it with rubber ring to avoid penetration of vapor Battery Snaps adhere Figure 25 Figure 26 Precautions The system is operated on wireless signal under certain situation the system may be unable to receive or reduce down the wireless signal as a result of environment intervention mistakes made during operation and improper installation When the tire cannot receive updated RF signal in 5 minutes consecutively its red legend light will be on to warn drivers When any of following situation happened please 1 Drive away the car it might be strong wireless signal intervention nearby 2 Please check if battery of Sensor is running out less than 2 6Volt please replace it with new one 3 Please contact with your dealer for assistance FAQ 2 What should do when the Sensor is with problems caused from lack of tire position labels tire position duplication or labels drop Resolution 1 We have done ID code settings on display and 4 pieces of Sensor while in delivery in case of 8 aforesaid problems please consult with your dealer for reset to avoid misplacements DDD 3 2 Wireless Signal Reception Start the engine power turned on For turn on the power switch open Host at the power switch Into the enter the receiving state Received all RF signals from 4 pieces of Sensor TPMS is ready
4. Head Up Display of Wireless Tire Pressure Detector User Manual Table of content 1 Before Use 1 1 Introduction of Product Safety 1 2 Check Accessories 1 3 Introduction of Product Function 2 Method of Installation 2 1 HUD of Installation 2 2 Sensor Installation 2 3 Troubleshooting for Installation 3 Installation Accomplishment 3 1 Wireless Signal Reception 4 Operation and Set up 4 1 Function Key and Set up Key Operation 4 2 Warnings and Legends 4 3 Tire Status Check up 5 Electric Utensil Regulation 5 1 Head Up Display 5 2 Sensor 1 Before Use gt gt gt 1 1ntroduction of Product Safety Head Up Display of Wireless Tire Pressure Detector HUD is security gear in of wireless detection of tire pressure It can project all critical information such battery and temperature pressure specified in every tire and voltage of battery on the front windshield which reminds drivers of being alert to the information about the travel and status of tire so as to reduce down incidence rate of break down and safety issues While any abnormal condition is detected the value in the voices lights issued a warning to drivers attention gt 1 2 ssories List Parts Quantity 1 HUD Host Unit Power Cable USB cigarette lighter Connector Reflective Film Velcro Tape Sensor roRt62a Baty animet sp ween Usermana O 1 3 Introduction of Product Function Photosensitive Power switch Test Area P
5. ick with clean wiper Figure 10 2 Tear off the release film at the reverse side of reflective film and spray a little bit of neutral soap water on glass projection area and reflective film surface Figure 11 12 3 Stick the reflective film onto front windshield and align it appropriately Figure13 4 Scratch out any drops of water between reflective film and glass with scratch board card and wipe it with clean wiper Figure 14 15 5 HUD installation is in completion Figure 11 Figure 12 Figure 15 Figure 14 Figure 13 DDH 2 2 Sensor Installation Step 1 Make sure four Sensor are pasted with tire position sticker Instruction 1 Take 4 Sensor and make sure if stickers marking 4 different positions of tires are pasted onto R 1 Right Front R2 Right Rear L1 Left Front L2 Left Rear Figure 16 LF L1 p B RF R1 LR L2 g B arin Figure 16 Step 2 Install Battery of SENSOR Instruction 1 Put batteries and snaps into Sensor by sequence and fasten up the lid Figure 17 Precaution 1 Negative pore of the battery shall be at bottom side and positive pore at upper side it will discharge instantly and run out of power if in reverse placement 2 Please fasten up the lid completely to avoid penetration of vapor Figure 17 Step 3 Install Sensor on the Tire Instruction Every piece of Sensor is identified by a unique ID Code tire positioned with HUD
6. nalreception Please replace with new batteries immediately gt gt 4 3 Tire Status Check up Press Set up key and it will show pressure temperature of every tire electric power of battery in a Sensor every value delays at 5 seconds 1 Tire 2 Tire Pressure Temperature O 3 Voltages of Battery 5 Electric Utensil Regulation gt gt gt 5 1 Head Up Display Voltage in Work 9 16V Electric Current in Temperature in oe i Storage gt gt 5 2 Sensor Temperature in nih Storage Battery konge in 2 EV 3 3V Detection
7. ower connector lt Function Key lt Set up Key 1 3 1 Function Key Press Function key under normal mode to display settings in a cycle 1 3 2 Set up Key Move to the function mode desired with Function Button and press Set up Button to reset press Function Button to exit settings once accomplishment 2 Installation DDH 2 1 Host Unit Installation First Step Search position of Host Unit Cigarette lighter Connector Figure 2 j Figure l Figure 2 Instruction 1 Circular connector connected host the rear cigarette lighter connector connected to the car cigarette lighter socket Second Step Turn on the power the display will start Figure 3 4 a n Figure 3 Figure 4 Instruction 1 If Cigarette lighter turn off the engine the power will be shut down the host switch normally open If engine is shut down the power will not turn off will be required to host the rear of the switch to turn off or unplug the cigarette lighter plug to prevent battery power depletion Figure 5 6 Figure 5 Figure 6 Step 3 Stick the Velcro Tape Instruction 1 Stick the velcro tape at bottom side of host unit then tear off the release film at bottom layer and place it on the site driver wants to project Figure 7 8 9 Figure 7 Figure 8 Figure 9 Step 4 Stick the Reflective Film Instruction 1 Wipe the site a reflective film is desired to st
Download Pdf Manuals
Related Search