GUARDIAN ANGEL USER MANUAL
Contents
1. GUARDIAN ANGEL USER MANUAL Guardian Angel is a digital wireless personal tracking device that keeps children pets keys and other valuables close by your side The Guardian Angel comes with a Base tracking unit and four Tag units that are each attached to tracked items e g keys This product can alert you when a tracked item goes out of range and can search for the item within a 1 600 foot radius A child or an elderly person can also press a panic button on the Tag unit to call alert the Base unit KEY FEATURES Works indoors and outdoors Lightweight and easy to use No assembly or installation only batteries Uses safe 2 4 GHz RF technology Base unit tracks up to four tags Out of range distances for a Tag unit can be configured at 16 feet 32 feet or 64 feet with some variability due to terrain and other factors 1 600 foot search radius distance will vary depending on terrain and other factors Base unit has a direction indicator to facilitate tag search Alerts are issued with a 95 dB alarm and vibration Tag units can issue a Panic Stress alert to the Base unit SPECIFICATIONS Model Name 807G Search Range 0 500m 1600 ft Function Alarm amp Search 1 to 4 Tags Alarm Distance Near 32 16 Middle 64 32 160 64 Base Unit Tag Unit Specs Base MO7A Tag S08A Battery Type AAA x 2 CR2032 Battery Life Time on Standby 60 days 8 hrs 30 days 8 hrs Beep Sound at 10 cm 3 92. Tag unit the Signal Strength lights will all be illuminated however if you are right on top of or very close to the Tag unit the Direction Indicator may give inaccurate readings At this point you should mute the Base unit Mute button on the side of the Base unit and follow the Tag unit s beep in order to pin point its location 7 Once the Tag unit is found press the Press and Search Set button on the Base unit again release to cease the search function SILENT SEARCH In quiet areas e g libraries it is possible to conduct a silent search where both the Base and Tag units are muted To do this simply turn on the Mute button on the Base unit before pressing the Search Set button and then use the Direction Indicator and Signal Strength lights MUTE MODE on the Base unit The Mute button on the side of the Base unit can be switched on at any time to silence the Base unit to avoid distraction in quiet areas e g libraries Page 7 The Tag units have an additional function of allowing a child or elderly dependent to call the Base unit for help To activate the Panic alert press and hold down the panic button on the Tag unit the Base unit will beep and vibrate and a solid bright red blinking Connect Status light on the Base unit will clearly indicate which Tag has activated the panic alert When the Base unit or Tag unit is not in use it is advised that you turn
3. pocket with other items blocking the signals Why is range alarm distance not consistent Because radio signal strength and signal reflection are affected by the environment and terrain users may need to adjust the out of range distances to compensate for environment factors No Alert when the Tag unit is out of range Check whether the Tag unit is Disalarmed on the Base unit Check for low battery on both units Check the out of range distance if the Tag unit is set for Far you may need a greater distance before setting off an Alert Page 9 8 1 If you want to use the device during air flight please comply with the air safety regulations for each respective country 2 We reserve the right to change the hardware software specifications and designs and the information in the manuals at any time without prior notice 3 Proper operating temperatures for this product are between 14 F 140 F 10 C 60 C Proper Storage Temperatures are between 4 F 185 F 20 C 85 C 4 The Batteries provided in this product should be disposed of properly according to national or regional recycling regulations contact local authorities for more information Warning Do not expose the batteries to fire or heat this may result in danger from explosions This equipment has been tested and proved to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits a
4. them off to conserve battery power When the Base unit or Tag unit battery charge runs low both units will issue a low level beep every 2 minutes alerting you to change the batteries If you run your units on low batteries operations may become unpredictable or results may be innacurate The Base and each of the Tag units are Paired before shipment that is each Base to Tag combination must have it s own unique communication handshake so that the Base does not get confused between the Tag units The procedures below are used to re establish the Pairing in case a Tag unit is replaced or a Tag unit cannot communicate with the Base unit For this example we Pair the Base unit and Tag 2 red follow the instructions below 1 Make sure the Base unit and ALL the Tag units are turned off 2 To enter Registration mode hold down the Configuration button on the Base unit and the Search button for Tag 2 also on the Base unit and then at the same time turn on the Base unit as soon as the red light above the Search button for Tag 2 flashes exactly twice release the buttons if you ve already reached the 3rd flash you have to start again If you ve entered the Registration mode successfully the light above Search button and the light below the Dis alarm light on the Base unit will flash together Finally bring Tag 2 to within 10 cm of the Base Unit and turn
5. ar by 2 You must first calibrate the Base to the current environment Hold the Base unit in front of you at chest level and scan the area slowly in a circular direction from right to left for 360 and again from left to right one 360 turn in 3 4 seconds Note If the Direction Indicator illuminates green on the Base unit during this calibration process it does not yet indicate a Tag unit s direction 4 Next slowly scan a third time from right to left The Direction Indicator on the Base Unit will illuminate green when it establishes the direction of the tagged item location Note You don t have to scan a full 360 you can use a narrower search angle e g 180 but you must still calibrate the Base Pressand unit from left to right right to left and then release scan to search Page 6 SEARCHING FOR A MISPLACED TAGGED ITEM continued 5 Move in the direction in line with where the front of the Base Unit points when the Green light is lit As you move closer and closer to the Tag unit the Base unit chirp intervals will increase in frequency and the Signal Strength lights will display additional red lights If the Base unit chirp intervals slow and the red Signal Strength lights become fewer you may be moving in the wrong direction and losing signal strength at this point you may Press and need to stop and recalibrate again Y release 6 As you become very close to the
6. e unit The blue Tag unit is associated with the far left status light 1 the red with the second the green with the third and the yellow with the fourth light If a single Tag unit goes out of range the respective Connect Status light will blink a bright red color On the Base unit below each Connect Status light is an fl Connect Status associated Search Set button Il Lights dedicated to one of the tag units In subsequent sections Search Set Buttons you will use this button to manage individual Tag units from the Base unit Page 4 SET OUT OF RANGE DISTANCES NEAR MIDDLE AND FAR The Base unit can configure more or less tolerable out of range distance limits Near Middle Far for each individual tag You can also deactivate the tracking function DISALARM to a certain Tag Unit 1 Hold down the the Configuration button on the side of the Base unit One of the Connection Status lights will illuminate red indicating one of the Tag units If it is NOT the Tag unit you want to configure then let go of the Configuration button and press down on it again the Connection Status light will illuminate for the next Tag unit in sequence Do this until you reach the desired Tag unit 2 While continuing to hold down the Configuration Button on the Base unit press the Search Set button underneath the illuminated Connection Status light Notice t
7. hat the illuminated Strength indicator light will change from Near Middle Far and Disalarm as marked on the Base Unit each time you press the Search Set button When you arrive at the desired setting let go of the Configuraton button and the changes will take effect for that Tag unit Note You can configure the out of range distance for a Tag unit only if that Tag unit and the Base unit are currently linked DISALARMING A TAG UNIT If there are one or more Tags that are not in use you can deactivate or Disalarm them so that the Base will not issue any alerts for them In the instructions above for setting out of range distances there is a fourth option marked Disalarm on the Base Unit You can set a Tag to this option if want the Base unit to disregard that Tag unit Page 5 When a tagged item is misplaced you can use the Base unit to search for it if it is within a 1 600 foot 500m radius Test this for Tag unit 1 in an open area e g large room or in your yard 1 On the Base unit press the Search Set Button once for Tag unit 1 one or more of the 5 Signal Strength lights will illuminate on the Base unit indicating the relative distance from Base to Tag The Base unit will also begin to chirp at regular j Press and intervals release The Tag unit will also begin to beep allowing you to follow the audible to pin point its location if it is ne
8. inches 95 dB 95 dB Vibration Vibration Motor None Dimensions L W H 3 75 x 2 56 x 0 56 2 38 x 1 5 x 0 42 Page 1 PACKAGE CONTENTS Model Name 807G2 807G4 Base Unit 1 pc 1 pc Tag Unit 2 pc 4 pc AAAx2 AAAx2 Batteries CR2032x2 CR2032x4 Strap 2 3 Hook Ring 1 1 1 1 User manual v v OVERVIEW Base Unit Front Back Strap attachment Connect status LED Power switch Search Set button Direction indicator Configuration button Signal strength lights Mute button Speaker Clip Battery cover Ring attachment Speaker Connect status LED Panic button Power switch Battery cover SUGGESTED LOCATION TO PLACE BASE TAG units Base Unit Tag Unit This section shows how to quickly setup and trigger an alert condition when the Base unit is separated from the Tag units 1 Insert the batteries into the Base unit and the four Tag units Slide out remove the battery covers on the Base and Tag Units Insert batteries included according to the polarity markings in the battery compartments Replace the battery compartment covers on both units Base unit Install Battery Remove Cover x Ga ad Replace Cover K 2 Switch On the power button on the Base and Tag units Disregard any alerts while the Base unit and 4 Tag units are linking up After the Base and all Tags link
9. it on The Tag unit will beep twice indicating a successful Pairing oO Page 8 Q In search mode why does the Base unit show the Tag location to be in A several directions The Base unit collects and compares RF signal strength from the Tag unit to determine location However when the Tag unit is already very close to the Base unit the signals can appear emanating from several directions This can also occur when both units are in an enclosed environment which causes signal reflection off of walls from different directions indicating a false location If this is the case you can mute the Base unit and simply follow the audio beep issued by the Tag unit during search mode Why does the Base unit occasionally indicate a false direction This is also caused by the reflection or blockage of the signal Signal reflection from walls or wire fences sometimes may indicate a false location A body of water e g fish tank for even people may block the signal and weaker reflected signals from surrounding metal objects may indicate a false direction To remedy this problem try adjusting your position wait for the Status Indicators to settle and try your search again What can cause false out of range alarm False alarms are caused by Base and Tag units are too close to each other Low battery power will cause unpredictable behavior such as false alarms Either the Base or Tag unit has been placed in a
10. re designed to provide reasonable protection against harmful interference in a residential installation This FCC Certifications equipment generates uses and can radiate radio frequency energy if not installed and used in accordance with the instructions it may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determinedly turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures m Reorient or relocate the receiving antenna FC m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected m Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept an interference received including interference that may cause undesired operation FCC Caution Any changes or modifications are not expressly approved by the party responsible for compliance which could void the user s authority to operate this equipment Page 10
11. up they will display blinking lights at regular intervals Replace Cover 3 Place the Tags in a stationary location and with the Base unit in hand walk away from the Tags At about 64 feet the Base unit will begin to vibrate and beep The Tag units will also beep 4 Return the Base unit to the vicinity of the Tag units and all beeping will cease D I ww 64 Feet Page 3 ADDITIONAL NOTES ON OUT OF RANGE ALERTS a When the Base loses the signal to a Tag unit i e out of range the Base unit beeps and vibrates for 10 seconds the Tag unit beeps for 15 seconds The Base unit will not alert continuously while the Tag is out of range but will continue to issue a beep every 30 seconds and try to relink to the Tag at regular intervals b When the Tag Units and Base Unit are within close proximity lights on all units blink dimly at regular intervals indicating active link statuses between Base and Tag units this is referred to as Standby Mode c You can Mute the Base unit alarm at anytime by pressing the Mute button on the right side MANAGING ALL 4 TAG UNITS FROM THE BASE UNIT In the Getting Started section you learned how to set off the out of range alerts for all the Tag units You now need to be prepared to manage all 4 tagged items from the Base unit at the same time with a little practice operations can easily be mastered There are 4 Connect Status lights on the Bas
Download Pdf Manuals
Related Search