Hand-Held Scanner User's Manual
Contents
1. Q Why do all the images I scan have the same date when saved on the memory card A The device does not have an internal clock to keep real time so the date amp time attributes are always a fixed date amp time assigned during production not current date amp time Q Why are my scanned images distorted A You may be scanning too fast scan again at a lower speed 5 2 User s Manual How can I tell if the scanner is scanning at 300 dpi or 600 dpi The scan indicator light indicates the selected resolution Green 300 dpi Orange 600 dpi Why there are strange lines on the scanned document Please check the following 1 Are there scratches on the original or is the original clean 2 Remove any stains or dust from the original before scanning 3 Clean the rollers and glass with the included cleaning cloth Refer to the section Cleaning the Rollers and Glass Will the scanner recharge my rechargeable batteries No the scanner does NOT recharge rechargeable batteries You must use your own battery charging device Why there is a red or gray background with lines on my scanned image The scanner does not enough power to perform a scan Charge your batteries and restart the scan Should the scanner feel warm to the touch It is normal for the scanner to emit a small amount of heat after prolonged use However if there are strange odors coming from the scanner or the scanner feels a lit2. Note 1 Refer to the following list for a proper scan speed based on an A4 size paper 0 6 second B amp W 300 dpi 1 6 second Color 300 dpi 2 4 seconds B amp W 600 dpi 6 5 Color 600 dpi 2 If you hold the scanner vertically and scan your original from right to left or from left to right your image will be rotated 90 Please use the included software application or other image editing software application to rotate the scanned image correctly 3 2 User s Manual 3 5 Start Sheet Fed Scanning with Feeder Dock By attaching the feeder dock into the scanner the whole unit allows you to start auto scan as soon as your document is inserted to the feed slot When the scan is finished the image is saved in the memory card Note e Only MiWand 2L Pro MiWand 2 Pro comes with a feeder dock e When the scanner is attaching to the feeder dock no battery is required to operate However you must connect the supplied power adapter to get the power Installation Press and HOLD the latch at the left end Plug the right end of the scanner to the right end of the feeder dock with the copper Strips inserting into the hole 3 Place the left side of the scanner to the slot Release the latch 5 Connect the power a From a power outlet through a power adapter Simply plug the small end of the power adapter to the power jack of the ducking unit and the other end to a power outlet Power Adapter Ava
3. 1 With the screen displayed press VN to enter the Menu mode 2 Press BA to scroll to Color Mode and then press to select it 3 Press bA to focus on your desired mode and then press to select it 4 Press Be to exit User s Manual 3 10 3 Save Format The scanner offers two types of file formats for your scanned image J PEG default fits for photos and PDF fits for text document Follow these steps to select your desired file format 1 With the screen displayed press VN to enter the Menu mode 2 Press bA to scroll to Save Format and then press to select it 3 Press BA to focus on your desired format and then press to select it 4 Press e to exit 3 10 4 LCD Off To let the scanner enter power saving mode the scanner provides option to turn off the LCD screen after idle for a specified time without turning off the power The choice includes 45 seconds default 90 seconds and 3 minutes To turn the LCD screen back on simply press any button Follow these steps to change the setting 1 With the screen displayed press VN to enter the Menu mode 2 Press bA to scroll to LCD Off and then press to select it 3 Press BA to focus on your desired setting and then press to select it 4 Press to exit 3 10 5 Power Saving To conserve power the scanner automatically shuts off after left idle for a specified time 90 seconds 3 minutes or 5 minutes Follow these st
4. t connect the battery to an electrical outlet directly Don t connect the positive and negative terminal directly with metal objects such as wire Short terminals of battery is strictly prohibited it may damage battery Do not transport and store the battery together with metal objects such as necklaces hairpins Do not strike throw or trample the battery Do not directly solder the battery and pierce the battery with a nail or other sharp object Do not use lithium ion battery and others different lithium polymer battery model in mixture Prohibition of use of damaged cells Don t bend or fold sealing edge Don t open or deform folding edge Don t fillet the end of the folding edge Don t fall hit bend battery body Battery pack designing and packing Prohibition injury batteries Never disassemble the cells Keep the battery away from babies Any components contacting these two edges they must be insulated Caution User s Manual Risk of explosion if battery is replaced by an incorrect type Dispose the battery according to local regulations Never place batteries or devices on or in heating devices such as microwave ovens stoves or radiators Batteries may explode when overheated or its performance will be degenerate and its service life will be decreased Do not use it in a location where is electrostatic and magnetic greatly otherwise the safety devices may be damaged causing hidden trouble
5. latched micro SD card Note e The scanner only accepts micro SD card in FAT16 or FAT32 format NTFS and other file formats are not supported e Always insert a micro SD card before calibrating and scanning 2 7 User s Manual cr Operation 3 1 Suitable and Unsuitable Original Types Suitable for Wand Scanning The scanner used as a wand scanner without the feeder dock is designed to obtain the best scanning results with photo and document up to 8 5 x 14 size Suitable for Feeder Dock The scanner used with the feeder dock is designed to obtain the best scanning results with the following types of originals e Photos and documents 3 x5 4 x6 5 x7 8 x14 e Business cards standard 3 5 x 2 or larger Unsuitable for Feeder Dock Do not use the following types of originals for scanning in the feeder dock otherwise the feeder dock may malfunction or cause the original to jam in the slot Originals thicker than 1 0mm Original with either side shorter than 55mm Originals with lots of black or dark colors Original with dark colors surrounding the edges Printed media newspapers magazines etc Soft and thin materials thin paper cloth etc Curl or wrinkle originals Originals with staples or paper clips Originals that exceed acceptable size 8 width x 14 length 216 mm x 356 mm 3 2 Turn on the Scanner Press to turn on the scanner The LED will
6. order they are stored on the SD card 3 Press PVA to view previous or next image 4 Press B to exit the Display mode and return to the Scan Ready screen 3 7 View or Download the Scanned I mages Windows 1 To view or download your scanned images you can either remove the micro SD card and connect it to a card reader or connect the scanner to your computer via the Supplied USB cable be sure to turn on your scanner When the scanner and your computer is connected successfully all tasks are interrupted and the USB connection screen is display Warning It is recommended to download the scanned images by removing the memory card from the scanner and then inserting the memory card to your computer instead of connecting the scanner directly to your computer with the USB cable since this may require a lot of battery power 2 Your computer should recognize the card or the scanner as a Removable Disk 3 Click the Removable Disk and you will find a folder of DCI M is created and all the PDF files will be stored in the subfolder of 200DOC and the JPEG files in the subfolder of LOOPHOTO File name starts from IMG_0001 pdf or IMG OO001 jpg 3 7 Each scanned image is given a file name with the prefix IMG_ followed by a 4 digit sequential number in the order the images are stored For example IMG_ 0001 jpg IMG 0002 jpg IMG_OOO1 pdf IMG_ 0002 pdf etc J PG files are stored in a sub folder titled
7. scanner will be displayed in iPad in 3 seconds 3 Choose Import All to load the scanned images to the album of your iPad iPad Camera Connector not included 3 9 Use the OCR Software Application The bundled software application allows you to convert image text to editable or searchable text through the OCR Optical Character Recognition process For detailed information on how to use the function please refer to the user s manual or the online help of the software application contained in the CD 3 9 3 10 Customize Your Scan Settings You can customize scanner settings through the Menu screen to fit different document types 3 10 1 Resolution The scan resolution is measured in dpi dots per inch The higher the resolution the more details the scanned image will be displayed However a higher resolution may require more disk space stored in the SD card The scanner offers two resolution modes 300 default normal or 600 dpi high quality Follow these steps to select your desired resolution 1 With the screen displayed press VN to enter the Menu mode 2 Press to select Resolution 3 Press bA to focus on your desired resolution and then press to select it 4 Press e to exit 3 10 2 Color Mode The scanner offers two color modes for your scanned image Color default fits for photos and Black and White fits for text document Follow these steps to select your desired color mode
8. you reformat your memory card all existing files on the card will be deleted To format your SD card Sean Ready 1 With the f screen displayed press VN to enter the Menu mode i Monu Dis ply 2 Press bA to scroll to Card Format and then press to select it 3 Press to select Yes 4 To confirm press VN 5 After successful format the Menu screen is displayed 6 Press e to exit User s Manual 3 10 8 Auto crop sheet fed scan only When using the feeder dock the whole unit has a built in cropping function to capture an image according to the actual size of your original as illustrated below This feature is available when using sheet fed scan with the feeder dock Original Auto crop on default Auto crop off Depending on the shape and size of your original you may want to perform additional manual cropping on the scanned image to achieve your desired final image Follow these steps to disable the auto crop feature 1 With the screen displayed press PN to enter the Menu mode 2 Press kd to scroll to Auto crop and then press to select it 3 Press to focus on desired mode and then press to select it 4 Press P to exit 3 10 9 Calibration If the scanned image has vertical lines or discolorations the scanner may need to calibrate in order for the Contact Image Sensor CIS to resume its color amp sharpness precision For calibration instructions see the Cali
9. DCI M LOOPHOTO The folder stores 9999 photo files and then automatically creates another sub folder titled LOLPHOTO and so on to 199PHOTO PDF files are stored in a sub folder titled DCI M 2O0ODOC The folder stores 9999 document files and then automatically creates another sub folder titled 201DOC and so on to 299DOC 3 7 1 Computer System Requirements for USB Connection Operating system Windows XP Windows Vista Windows 7 Mac 10 5 or above Mac is used only for data transferring USB port USB 2 0 USB 1 1 3 7 2 After Successful Connection When the scanner connects with the PC an additional drive is listed in the Explorer window titled Removable Disk drive letter or the personalized title you may have previously assigned to your microSD card 3 7 2 1 Safely Disconnect Scanner micro SD Card From PC i 2 On the Windows System Tray click the hardware removal icon Click the Safely remove USB mass Storage device message with the corresponding Drive When the Safe to Remove Hardware message appears you can safely remove the scanner s USB cable 3 8 User s Manual 3 8 View or Download I mages with iPad 1 Plug the iPad Camera Connector not included to iPad dock connector Plug the mini USB connector of the supplied USB cable to the Mini USB port of your scanner and plug the USB connector of the supplied USB cable to iPad Camera Connector 2 The Ske images in the micro SD card of your
10. Hand Held Scanner User s Manual Regulatory model HF 1115B HF 1116B Avision Inc manual en 250 0746 E miwand2all vl Trademarks Microsoft is a U S registered trademark of Microsoft Corporation Windows Windows XP Windows Vista and Windows 7 are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries IBM IBM PC are registered trademarks of International Business Machines Corp Other brands and product names herein are trademarks or registered trademarks of their respective holders Copyright All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of Avision Inc Material scanned by this product may be protected by governmental laws and other regulations such as copyright laws the customer is solely responsible for complying with all such laws and regulations Warranty The information contained in this document is subject to change without notice Avision makes no warranty of any kind with regard to this material including but not limited to the implied warranties of fitness for a particular purpose Avision shall not be liable for errors contained herein or for incidental or consequential dam
11. ace the calibration sheet back into the plastic cover and store it in a safe place for future use 4 1 During calibration move the scanner only in the white area Warning Do not interrupt the calibration sequence or try to shut off the device while it is calibrating If you stop the calibration before it has completed a calibration error may occur As a result when you next power up the unit an error message may be displayed and you will have to power off the unit and repeat the instructions in this section Calibrate the scanner only when color of the scanned image looks abnormal Make sure the memory card is inserted Keep the calibration sheet from dust and debris Any dirt may make the calibration chart invalid or impact the calibration result Use only the included calibration sheet to calibrate the scanner 4 2 Clean the Scanner and Feeder Dock It is recommended to clean the scanner and feeder dock approximately every 200 scans or if vertical lines or stripes appear on the scanned image Use only the recommended or supplied tool to clean the scanner and feeder dock Cleaning steps Clean the wand scanner 1 Remove the scanner from the feeder dock Turn the scanner over to reveal the rollers and glass Wipe the rollers and the glass with the included cleaning cloth Wipe the scanner with a dry and clean lint free cloth Rollers Glass Wand Scanner 4 2 User s Manual Clean the fee
12. ages in connection with the furnishing performance or use of this material Disposal of Waste Equipment by Users in Private Union a This symbol on the product or on its packaging indicates that the product can not be disposed of with your other household waste Instead it should be sent to appropriate facilities for recovery and recycling in an effort to protect human health and the environment Fore more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or the shop where you purchased the product il User s Manual FCC Radio Frequency Interference Statement This product has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The FCC Class B limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment d
13. and hold for 3 seconds to turn off the scanner Enters Display mode from Scan Ready screen Navigate forward through images and menu options Return to previous screens or exists from Display mode or Menu option 7 Battery Slide to remove the cover compartment 1 3 1 4 Rear View Used to plug the mini end of the USB cable to oe connect to PC Memory card slot Used to insert a memory card 1 5 Bottom View The rollers are sensors and should only be rolled in 1 ela one direction Do NOT roll back and forth while rollers scanning except during calibration gt Glass While rolling scanner over a document the optical sensor in the glass reads and scans the image 1 4 User s Manual 1 6 Front View with Feeder Dock Item Description 1 Guide Slide Slide the guide to fit your document size gt Feed Slot Used to insert original into the feed slot to begin scanning Used to disengage the wand scanner from the 3 feeder dock 4 DC Jack Used to plug power adapter 1 5 1 7 Scanner Indicator Light Scanner 7 760 3 mere i Status Indication Off Scanner is off or scanner is on and ready for use Orange briefly Powering on for initialization Green steadily on scanning In progress in 300 dpi Orange steadily on Scanning in progress in 600 dpi Green or Orange Processing scanned image flashing Red flashing No SD card SD card full card
14. and then press to select it 3 Press to focus on desired mode and then press to select it 4 Press e to exit 3 17 4 User s Manual Maintenance 4 1 Calibrate the Scanner Calibrate only if the scanned image looks fuzzy the color looks abnormal e g darker than normal after 8K scanned or the scanner has been stored without use for a long time The calibration process resets the Contact Image Sensor to resume its color and sharpness precision Calibration can only be performed with the wand scanner out of the feeder dock When the scanner is attached to the feeder dock the calibration feature is disabled To calibrate the scanner complete the following steps 10 Make sure the battery is fully charged and a memory card is inserted Remove the calibration sheet from its plastic cover and lay it on a flat surface with the printed side UP Remove the scanner from the feeder dock Place the scanner on the white area of the calibration sheet at the top of the white area Make sure the sheet is clean i e no debris or colored objects With the screen displayed press VN to enter the Menu mode Press kd to scroll to Calibration and then press to select it Press to select YES The scanner enters Calibration mode Slowly slide the scanner down over ONLY the white area of the calibration sheet The scanner completes the calibration sequence and automatically powers off Carefully pl
15. be flashing and then extinguished The Scanner Ready screen will be displayed as illustrated Scan Ready pm Scan to card amp Menu ETEN Press again for about 3 seconds to turn off the scanner The scanner will be automatically shut off if it is left idle for 3 minutes 3 1 3 3 Choose Your Desired Scan Settings 1 On the Scan Ready screen press FN to enter the Menu mode Scan Ready 2 A list of menu options is displayed The options include a oe Resolution Color Mode Save Format LCD Off and so on FC Abel 3 Press bA to focus on your desired option such as Save Format and then press to select it Resolution 4 Press kd to focus on your desired item such as PDF and Color Mode then press to select it Save Format LCD Off 5 Press to exit r W Enter To increase ease of use please first go to Menu and then choose Language to select your desired language on the screen Default settings Resolution 300 dpi Color Mode Color File Format JPEG LCD Off 45 sec 3 4 Start Wand Scanning Hand Held 1 Place your document on a flat surface 2 Press to start a scan 3 Hold the scanner and glide the scanner gently over the surface of the page as illustrated 4 Press to stop the scan By default the Preview mode is on allowing you to view the scanned images for 2 seconds immediately after scanning available for J PEG file format only
16. brate the Scanner section Calibrate the scanner only when the color of the scanned image looks abnormal 3 15 3 10 10 Language The scanner offers multi lingual text for LCD screen Choice includes English German French Dutch Italian Spanish Chinese Traditional Chinese Simplified Japanese Korean and so on However the availability of the languages varies based on your area Follow these steps to choose your desired language 1 With the screen displayed press VN to enter the Menu mode 2 Press kd to scroll to Language and then press to select it 3 Press to focus on desired language and then press to select it 4 Press e to exit 3 10 11 Factory Default At any time you can reset all menu settings back to the factory defaults To reset to defaults 1 With the screen displayed press VN to enter the Menu mode 2 Press bA to scroll to Factory Default and then press to select it 3 Press to select YES 4 To confirm press VN 5 After a successful reset the scanner automatically shuts off Press to turn the scanner back on 6 Press to exit User s Manual 3 10 12 About The About option lists the current Firmware and Calibration versions You may need this information if you contact our Customer Support Follow these steps to view the About information 1 With the screen displayed press VN to enter the Menu mode 2 Press kd to scroll to About
17. der dock 1 Remove the scanner from the feeder dock 2 Wipe the rollers with the included cleaning cloth 3 Wipe the feeder dock with a dry and clean lint free cloth Rollers Note e Adding some isopropyl alcohol 95 on the cleaning cloth is more efficient when cleaning the rollers Do not use any solvents or corrosive liquid i e alcohol kerosene etc to clean any part of the scanner otherwise the plastic material will be permanently damaged Make sure the surface of the document or photo doesn t have any paper clips etc or this could damage the scanner glass lens 4 3 User s Manual 5 Troubleshooting 5 1 Error Messages If there is error during scanning the LED light will be flashing in red color and error message will be displayed Refer to the following table to clear the error conditions Error Message Root Cause Code Purpose How to restore Insert Memory 1 No memory card inserted Insert a memory card Card 2 Card not recognized 2 Try a different card Card is full can t save scanned Free more space or insert a new Card Full image to inserted memory card micro SD card Low battery Battery power getting low Replace batteries or recharge if using rechargeable batteries Wait until message disappears 2 Scanner time out Format Fails 1 Memory card not recognized Use a different card 2 File system is not FAT16 FAT32 Calibration Fails Internal check failed and
18. dually or as a slideshow 3 6 1 Set Preview Mode By default the Preview mode is on allowing you to view the scanned images for 2 seconds immediately after scanning available for J PEG file format only Two options appear on the screen with the image allowing you to press VN to Save default or press A to Delete the image immediately When Preview mode ts off the JPG scanned image is saved immediately without displaying a preview Scans performed with Preview mode off use less battery power so you can expect more scans with Preview mode off Follow these steps to disable the Preview mode 1 With the screen displayed press VN to enter the Menu mode 2 Press kd to focus on Preview and then press to select it 3 Press bA to focus on Off and then press to select it Aii w N AA The Preview Screen 4 Press to exit Wi We View Scanned J PEG images as Slideshow 1 With the screen displayed press bA to enter the Display mode 2 The slideshow automatically begins and displays the images in the alphanumeric order they are stored on the SD card 3 To pause the slideshow press to restart the slideshow press again 4 Press at any time to exit the slideshow 3 6 User s Manual View Scanned J PEG images Individually 1 With the screen displayed press kd to enter the Display mode 2 The slideshow automatically begins and displays the images in the alohanumeric
19. eeeeseneeneenees 3 2 3 5 Start Sheet Fed Scanning with Feeder DOCK cc cece cece cece eeeeeeeeeenes 3 3 3 6 Preview Scanned Images on the LCD Screen cc cece cece ects eeeeeeeneeees 3 6 3 7 View or Download the Scanned Images Windows ccceeeeseeeeeeeeees 3 7 3 7 1 Computer System Requirements for USB Connection 3 8 3 7 2 After Successful CONNECTION cccccc cess cece cece Eirik ar E 3 8 3 8 View or Download Images WIth iPad cece cece ee ceee seen eee eeeteeeeeennnnenes 3 9 3 9 Use the OCR Software Application c cece cece cece eeeeeeeeeeeeeeeeeeneeneenees 3 9 3 10 Customize Your Scan Settings ssssesererrrrererrererrrrererrrrerrrrrrerrrrre 3 10 SELON REC OURO canieint ee cara eesarestaerqnuipanorence rer A einen 3 10 AO COO WO Sa eeprom E nea E O ETE a 3 10 SOS Save ForMal eesriie enri e Rra EAA EENE EENES TREE 3 11 2AA CCD O een ee ee nt a E A E 3 11 3 10 5 Power Saving ssssessrerrererrrrerrrrrrererrerrrrrrererrrrrrerrrrerrrrne 3 12 3 10 6 Anti mirror wand scans only s sesesesrerererrererrererrrrrrererrne 3 13 SO Care FON Eear AE ANN 3 14 3 10 8 Auto crop sheet fed scan ONIy c cece cece cece eeeeeeeeeeeeeeeeas 3 15 SOF CDa sajacang tas ciave AAA EOE 3 15 SALO MGM OUA OC waar a R see een wasnt areca E E G 3 16 JA nt Fac Dela UG eicaeaeice inten cede O LEE EErEE 3 16 AA ADOT epveasates cis E E aerate eae 3 17 vi User s Man
20. eight Dimensions WxLxH Operating Environment Storage Environment Description HF 1115B HF 1116B MiWand 2L MiWand 2L Pro HF 1115B MiWand 2 MiWand 2 Pro HF 1116B Contact Image Sensor CIS 1 8 TFT LCD 16MB 8 x 14 216 x 355 mm 3 minutes J PEG PDF 300 dpi 600 dpi Rechargeable Li ion battery compatible with NP45 3 7V 700mAh CA NP45 3 7V 700mAh 2x AA alkaline batteries or 2 NiMH rechargeable batteries Warning Never mix battery types as this could cause damage or fire The scanner does not recharge rechargeable batteries AC Adapter 100 240V 50 60 Hz input 5Vdc 1 0A output Wand Scanner 250 g Feeder Dock 413 g Wand Scanner docked 663 g Wand Scanner 41 x 258 x 36 mm Feeder Dock 69 x 322 x 57 mm Temperature 52C 352C 592F 95 F Humidity 20 85 RH Temperature 20 C 602C Humidity 20 85 RH 6 1
21. eps to change the time setting Sean Ready 1 With the jee screen displayed press PN to enter the Menu mode h Monu WF Diapliy 2 Press kd to scroll to Power Saving and then press to select it 3 Press kd to focus on your desired setting and then press to select it 4 Press e to exit 3 12 User s Manual 3 10 6 Anti mirror wand scans only When the Anti mirror feature is turned on default the scanner allows you to scan an Original either from top to bottom or from bottom to top In either way you can obtain a correct scanned image The scanner automatically detects your scanning direction and if you scan your original from bottom to top the scanned image will be automatically flipped and rotated upside down When Anti mirror is turned off if you scan your original from bottom to top your scanned image will be upside down and mirrored the right side and left side of your image will be reversed This feature is only available when using the scanner as a hand held wand scanner Scanning direction Anti Mirror on The Scanned I mage Top to bottom Bottom to top Follow these steps to turn Anti Mirror off 1 With the screen displayed press VN to enter the Menu mode 2 Press bA to scroll to Anti Mirror and then press to select it 3 Press bA to focus on your desired setting and then press to select it 4 Press e to exit 3 13 3 10 7 Card Format Warning If
22. error no scan performed after initiating wand scan mode or low battery 1 6 User s Manual 2 Installation 2 1 Precautions Keep the product out of direct sunlight Direct exposure to the sun or excessive heat may cause damage to the unit Do not install the product in a humid or dusty place Place the product securely on an even flat surface Tilted or uneven surfaces may cause mechanical or paper feeding problems o Retain the product box and packing materials for shipping purposes 2 2 Remove Scanner from the Feeder Dock 1 Press and hold the latch 2 Lift the left end of the scanner 1 3 Detach the right end of the scanner from the feeder dock Warning Do not lift the scanner too high and avoid using force to detach the scanner from the feeder dock in case the connector may be damaged 4 Remove the protective tapes on the scanner and inside the feeder dock as indicated Protective Tapes 2 1 2 3 Install the Batteries For the model of MiWand 2 MiWand 2 Pro 1 Push and remove the battery cover on the scanner 2 Insert 2x AA batteries into the battery compartment Make sure the batteries are inserted with the correct polarity note correct direction 3 Insert the battery cover Note e The LED light on the charger does not turn off when charging is complete It turns off only when the safety time 18 hours expires e The scanner does no
23. found Recalibrate the scanner see the calibration data error Calibrate Scanner section Scanned speed Images look distorted Moving Move the scanner over the too fast wand scanner over original too fast original slower and if necessary rescan the original Paper jam Original has become stuck in Remove the scanner from the the feeder dock feeder dock and then gently pull the original out of the feed slot Or you may press to eject the original Original exceeds max length 14 Warning 1 If low battery is indicated on the LCD display it is recommended to replace the batteries to prevent possible incomplete scanned images or other operational problems 2 If 2 AA Alkaline batteries have been used when battery power is low you may obtain incomplete scanned images or encounter operational problems before low batteries is indicated on the LCD display 5 1 5 2 Frequently asked questions and answers Q Why does not my scanner turn on A 1 The scanner may not be engaged with the feeder dock correctly 2 The batteries may not enough power or may not be inserted correctly Q The image can not be saved into the memory card while scanning a Make sure you have a microSD card inserted correctly and that it has adequate space Q Why doesn t my computer recognize my scanner when It s connected via USB cable A Make sure the cable connection is correct and secure Restart the computer if necessary
24. ilable for full version only 3 3 b From a power outlet through a USB power adapter not included Simply plug the small end of the power adapter to the power jack of the ducking unit and the other end to a power outlet through a USB power adapter not included USB Power Adapter O not y Te included a C From a computer through a USB cable Plug the small end of the USB power cable to the power jack of the ducking unit and the USB connector to the USB port of your computer D From a USB power bank not included Plug the small end of the USB power cable to the power jack of the ducking unit and the USB connector to the USB port 5V 1A of your USB power bank 3 4 User s Manual Operation 1 Press to turn on the scanner 2 Refer to the section Customize Your Scan Settings to select your desired scan settings 3 Insert a page FACE UP and align it to the left edge of the feeding slot The scan is automatically started when your document is fed into the feeding slot When the scan is finished the image is saved in the memory card By default the Preview mode is on allowing you to view the scanned images for 2 seconds immediately after scanning available for J PEG file format only 3 5 3 6 Preview Scanned I mages on the LCD Screen You can quickly and easily preview your J PEG images on the LCD screen immediately after a scan or at any other time You can also view all images indivi
25. oes cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user iS encouraged to try to correct the interference by one or more of the following measures m Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult your point of purchase or service representative for additional suggestions CE European Union Regulatory Notice Products bearing the CE marking comply with the following EU Directives Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC CE compliance of this product is valid if powered with the correct CE marked AC adapter provided by Avision This machine is certified as Class 1 LED product This means that this machine does not produce hazardous laser radiation ill Warning and Precautions of the lithium ion battery Warning Danger warning to prevent the possibility of the battery from leaking heating explosion please observe the following precautions Don t immerse the battery in water and seawater Please put it in cool and dry environment if no using Do not discard or leave the battery near a heat source as fire or heater Being charged using the battery charger specifically for that purpose Don t reverse the positive and negative terminals Don
26. of safety If the battery leaks and the electrolyte get into the eyes Do not wipe eyes instead rinse the eyes with clean running water and immediately seek medical attention Otherwise eyes injury can result If the battery gives off an odor generates heat becomes discolored or deformed or in any way appear abnormal during use recharging or storage immediately remove it from the device or battery charge and stop using it Avoid charging batteries for more than a week as overcharging may shorten battery life Over time unused batteries will discharge and must be recharged before use Disconnect chargers from power sources when not in use Use batteries only for their intended purposes Store the battery at 0 C to 40 C Avoid exposing your device and batteries to very cold or very hot temperatures Extreme temperatures can cause the deformation of the device and reduce the charging capacity and life of your device and batteries Prevent batteries from contacting metal objects as this can create a connection between the and terminals of your batteries and lead to temporary or permanent battery damage In case the battery terminals are dirt clean the terminals with a dry cloth before use Otherwise power failure or charge failure may occur due to the poor connection with the instrument Be aware discharged batteries may cause fire Follow all local regulations when disposing of used batteries or devices Never crush o
27. r puncture the battery Avoid exposing the battery to high external pressure which can lead to an internal short circuit and overheating Table of Contents Bi Re arii 1 1 LL TATOU erene A E AE SA 1 1 l 2 Package GOMMCIUS ascsanceacnssieves anenivh oesdaieis aoe EDE AO seen tases E EE 1 1 LS LOD VICW een EE E 1 3 LA RE WCW ee E E A E EEA 1 4 to BOO VION reee ea E hiss riaw ara entire EEE EEE 1 4 1 6 Front View with Feeder Dock ccccccccseeee nese eeseeeeeeeeeeeeesseeeesneenenees 1 5 1 7 Scanner Indicator Light cece ener e eee 1 6 Es TAERAA ee pei bh ee ate ck de ceeenee tee cannedeceeausiseenanssatens 2 1 2L FPR CUON carectrceiera set vatice vases E TA agains deeded E E E EE A rena 2 1 2 2 Remove Scanner from the Feeder DOCK essanesuesrererrerererrererrrrrrerrrrerrrre 2 1 2 5 Instal the Dat CNleS secerneren e eE ren eeu EE aA 2 2 2 4 Charge the Batteries sssnenerrerererrrrrrerrrrerrrrrrerrrrrrererrrrerrrrrrerrerne 2 4 LAAL VaMe USB CADOG osea NEE 2 5 2 4 2 Via the power adapter or USB power cable cccceeeee eee eee 2 5 2 3 Install micro SD Cardessa uina EE gone 2 7 Se D a ice eee ree 3 1 3 1 Suitable and Unsuitable Original Types nsssssererrerererrererrrrererrrrerrrre 3 1 I2 TUMON S Cane erinrar E EAE E AEE EE ER EERE 3 1 3 3 Choose Your Desired Scan Settings sssessrerrererrrrererrererrrrrrerrrrererre 3 2 3 4 Start Wand Scanning Hand Held cccc cece eee eeesseeeeeeeee
28. ries or 2 NiMH rechargeable batteries AA battery charger Available for full version only 2 4 User s Manual For MiWand 2L MiWand 2L Pro There are two methods to charge the batteries through the USB cable to the computer or through the power adapter or the USB power cable to the electric outlet 2 4 1 Via the USB cable 1 Turn off the scanner 2 Connect the mini USB connector to the USB port of the scanner 3 Connect the other USB connector to the USB port on your computer Important e Do not turn on the scanner power when charging the battery e Charge the batteries for at least 2 hours until green LED goes off before using the scanner 2 4 2 Via the power adapter or USB power cable 1 Turn off the scanner 2 Insert the scanner in the feeder dock 3 Insert the small end of the power adapter to the feeder dock and the other end to a power outlet 2 5 Or 3 Insert the small end of the USB power cable to the feeder dock and the other end to a computer or a power outlet through a USB power adapter not included USB Power Adapter not included Important e Do not turn on the scanner power when charging the battery e Charge the batteries for at least 2 hours until green LED goes off before using the scanner 2 6 User s Manual 2 5 Install micro SD Card You must install a micro SD card to the SD slot of the scanner to store your images Gently press in until the SD card is
29. t recharge the rechargeable batteries 2 2 User s Manual For the model of MiWand 2L MiWand 2L Pro with Li lon Battery 1 Push and remove the battery cover on the scanner 2 Load the battery into the battery container Make sure the battery is loaded with the correct polarity Note the copper strips on the battery should be touching the copper strips on the device inside the battery container Note Please use only the supplied battery 3 Insert the battery cover 2 3 2 4 Charge the Batteries For MiWand 2 MiWand 2 Pro The scanner comes with a battery charger and 2 pieces of AA rechargeable batteries to let you reuse batteries Please follow these steps to recharge the rechargeable batteries 1 Insert 2 rechargeable batteries into the battery charger Make sure the batteries are inserted with the correct polarity note correct direction 2 Plug the battery charger into an electrical outlet A green LED light appears on the charger while the batteries are charged Note every time the batteries must be charged for 7 hours 3 When charging is complete unplug charger and remove batteries to prevent overcharging and cause damage to the batteries Note 1 The LED light on the charger does not turn off when charging is complete It turns off only when the safety time 18 hours expires 2 The scanner does not recharge the rechargeable batteries 3 The scanner can only run on 2x AA alkaline batte
30. t your checklist If you do not receive all the items please contact your authorized local dealer immediately 1 2 Package Contents eo B microSD Card User s Manual Standard package items USB Cable Cleaning Cloth Feeder dock Software CD USB Power Cable Rechargeable Charger Power Adapter 1 1 Package items vary based on your scanner model MiWand 2 2xAA batteries battery charger MiWand 2L Li lon battery CD MiWand 2 Pro Feeder dock 2xAA batteries battery charger USB power cable power adapter MiWand 2L Feeder dock Li lon battery USB power cable power adapter CD Pro The model names of MiWand 2 and MiWand 2 Pro apply for the regulatory model number of HF 1116B The model name of MiWand 2L and MiWand 2L Pro apply for the regulatory model number of HF 1115B x The SC version of that model does not include this item Note Retain the scanner box and packing materials in case you may use them for shipping purposes 1 2 1 3 Top View User s Manual Indicates the operating warning status of the scanner 1 System indicator light 2 LCD display Displays preview pictures and settings menus Power Scan button Down arrow 5 Enters Menu screen from Scan Ready screen Navigate backward through images and menu options Press to turn on the scanner Press to start or end a scan Accept option choice in Menu and Preview options Press
31. tle bit hot to the touch turn the scanner off immediately 5 3 5 3 Technical Service Before contact Avision please prepare the following information Scanner serial amp revision number located on the bottom of the scanner m Hardware configuration e g your host CPU type RAM size free disk space display card interface card Avision Inc No 20 Creation Road Science Based Industrial Park Hsinchu 300 Taiwan ROC TEL 886 3 578 2388 FAX 886 3 577 7017 E MAIL service avision com tw Web Site http www avision com tw Avision Labs Inc 6815 Mowry Ave Newark CA 94560 USA TEL 1 510 739 2369 FAX 1 510 739 6060 E MAIL sSupport avision labs com Web Site http www avision com Hongcai Technology Limited 7A No 1010 Kaixuan Road Shanghai 200052 P R C TEL 86 21 62816680 FAX 86 21 62818856 E MAIL sales avision net cn Web Site http www avision com cn Avision Europe GmbH Bischofstr 101 D 47809 Krefeld Germany TEL 49 2151 56981 40 FAX 49 2151 56981 42 E MAIL info avision europe com Web Site http www avision de 5 4 User s Manual 6 Specifications Specifications are subject to change without notice item Regulatory model number Image Technology Scanner Display Memory Max Document Size Auto power off Output File Format Resolution Power Wand Scanner MiWand 2L MiWand 2L Pro MiWand 2 MiWand 2 Pro Feeder Dock Net W
32. ual MEIN CNENCG hindi A A E A 4 1 4 1 Calibrate the Scanner oo ccc cc cece eee eee eee eee eeeeeeteeeeeneeueeteenventeenentaes 4 1 4 2 Clean the Scanner and Feeder DOcK c ccccc cece ce cece scenes eeeeeeeeeeeeeeeneenes 4 2 TPEGUDICSNOOENIG icccoverrcesesssesesexier enikan 5 1 Sele EOE MICS GOS a ops connec Gerretse ences tse tesneeoce cues EEEE AEEA 5 1 5 2 Frequently asked questions ANd ANSWETSS cccee cece seeeeeeeeeeeeeeeeteneeneees 5 2 5 3 Technical Service cccccccccecccceeeeeeeeeeeeeeeeeeeeeeeeteeueeteeueeteeuueteeunentennenns 5 4 S INE RGA E aA 6 1 Vil User s Manual i Overview 1 1 Introduction Congratulations on your purchase of the portable handheld scanner With this scanner you can scan and store your photos or documents directly to a micro SD card without any computer Simply turn on the scanner press the Power Scan button to start and slide the scanner on the surface of your document and press the Power Scan button again to stop The scanned image is stored into your micro SD card What is best the scanner allows you to preview your scanned images with a built in color LCD display to confirm the document you have just captured Before you install and operate the product please take a few minutes to read through this manual It provides proper instructions for you to install operate and maintain the product The following figure indicates the package contents Please check all the items agains
Download Pdf Manuals
Related Search