USER MANUAL
Contents
1. isn t electvified and again or elecerity the Input Power switch is not cord Overload of the UPS Verify that the load matches the UPS capability specified in the specs failure back up load low more 3 Battery defect due to 3 Replace with the same type high temperature of battery operation environment or improper operation to battery lost between UPS installed well software and computer 2 Cable is not properly 2 Check the RS 232 or USB connected cable is firmly connected to COM1 COM2 of the computer and confirm the setting again LCD display broken properly Specification Blazer Vista MODEL a gt ee ee 800 CAPACITY VA W 400 240 600 360 800 480 Voltage Range 81 145VAC 162 290VAC INPUT Voltage 110 120VAC 220 230 240VAC Voltage Regulation 10 Battery Mode Frequency Regulation 1 Hz Battery Mode Output Waveform Modified Sine wave Battery Type 12V 4 5Ah 12 28W 12V 34W BATTERY Back up Time 10 mins 100W 18 mins 100W 22 mins 100W Recharge Time 8 Hours to 90 after complete discharge TRANSFER TIME Typical 2 6ms typical 10 ms max The LCD will always turn on when UPS work INDICATOR LCD Display Models l Including in off charging mode and fault mode Backup Mode Sounding every 10 seconds Battery Low Sounding every 1 second Overload Sounding every 0 5 seconds ALARM Overload Sounding every 0 5 seconds Battery replace Sounding every 2 seconds Continuous2. display as below Cs CU INPUT OUTPUT A LINE MODE lt 2 anni B 2 When in AVR mode it will display as below And the mark will flicker every 1second qo se E g ZZ VAC 2 gt ai KO INPUT OUTPUT Ge LINE MODE ave 8 ome sept D J 3 When in battery mode it will display as below And the mark 3 will flicker every 156600 ETE D LIRA INPUT OUTPUT annl EZI BACKUP MODE RD Note If I P V lt 40V gt input voltage will display 000 4 When in off charging mode it will display as below ET ERE LL 1 INPUT OUTPUT ume Note the output voltage always is displayed as 000 in off charging mode 5 When in fault mode it will display as below FAULT character and the reason of fault only Note the fault code will be showed in fault mode 6 Load level definition Load LEVEL Load bar Indication 0 25 7 Battery capacity definition Battery LEVEL Battery bar Indication Battery voltage lt 11V 8 When over load the mark 4 will flicker every 1second 9 When battery low the mark E will flicker every 1second Software Installation WinPower WinPower is a brand new UPS monitoring software which provides user friendly interface to monitor and control your UPS This unique software provides safely auto shutdown for multi computer systems while power failure With this software users can
3. monitor and control any UPS on the same LAN no matter how far from the UPS 15 WinPower Manager Ver 1 0 ZZ zloj x System Logs UPS Tools Monitor Preference Language Help Root 9 BILAN 9 cs 2000 UPS Status UPS Normal 14 45 a n On Battery g300 E Load 210 Ge GL backup Er AC LINE e UPS p LOAD AN GB WAN Model OFF LINE gt PS gt PS SN Com Port COMI 4 err Standard 120 N Temp 330 C 4 Capacity 1000 2004 01 20 14 44 33 Agent Start GEO Installation procedure 1 Go to the website http www ups software download com winpower htm Choose the operation system you need and follow the instruction described on the website to download the software When downloading all required files from the internet enter the serial No 511C1 01220 0100 478DF2A to install the software When your computer restarts the WinPower software will appear as a green plug icon located in the system tray near the clock Trouble Shooting Use the table below to solve minor UPS installation or operation problems If any abnormal situations occur that are not listed above please call service people immediately Symptom Possible Cause No LED display on 1 Missing battery 1 Charge battery up to 8 the front panel hours 2 Battery defect 2 Replace with the same type of battery 3 When the Input cord 3 Press the power switch
4. sounding Buck boost with Sounding every 0 5sec after 25min gt 70 SPS load And fault after 30 mins Discharge Overcharge short circuit PROTECTION Full Protection and Protection PHYSICAL Dimension DxWxD 330 100 140 mm WEIGHT Net Weight 4 4Kg 5 6Kg 6 1Kg Operating daget scare ZE E ENVIRONMEN 0 40 C 0 90 Relative Humidity non condensing INTERFACE SmartRS 232 Windows family Sun Solaris IBM Aix Compag True64 optional UnixWare FreeBSD HP UX Linux and MAC USB optional For Windows family amp Mac
5. Plug the unit into an appropriate power supply and allow the UPS to charge fully by leaving it plugged in for 8 hours 4 Computer Connection Connect one computer related device into each of the power receptacles supplied on the back of the UPS maximum of three devices 5 Modem Phoneline Connection Plug incoming internet line into the In socket at the back of the UPS Use one more Internet line cable and plug one end of the Internet line cable to the Out socket at the back of the UPS Plug the other end to the modem input socket as shown Ti Modem Fax Phone 6 Serial Cable Connection To allow for unattended system shutdown for your operating system connect the serial cable as per diagram below 7 Turn On Off To turn on the UPS unit press the power switch lightly To turn off the UPS unit press the power switch again When Swith The LED lighting 8 LCD Display Specification The LED will always turns on when UPS works including in off charging mode and fault mode When LCD start to work it will display all information for 3s INPUT BATTERY ITZA Lee gt Unit VDC Hz VAC Ls LE E LL a Si Bia OUTPUT LOAD FAULT INPUT BATTERY OUTPUT LOAD FAULT Unit HZ VAC So ume mope ave 2 MM LOAD LEVEL EZ Backup mone G BATTERY CAPACITY ee ee LINE MODE AVR BACKUP MODE 1 When in normal mode it will
6. USER MANUAL Blazer Vista 400 600 800VA Uninterruptible Power System IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions for models Blazer Vista 400 600 800VA that should be followed during installation and maintenance of the UPS and batteries Safety CAUTION This UPS utilizes voltages that may be hazardous Do not attempt to disassemble the unit The unit contains no user serviceable parts Only factory service personnel may perform repairs Internal battery voltage is 12Vdc Sealed lead acid 6 cells battery 6 Connection to any other type of receptacle other than a two pole three wire grounding receptacle may result in s shock hazard as well as violate local electrical codes In the event of an emergency turn the power switch to the of position and disconnect the power cord form the AC power supply to properly disable the UPS 6 Do not allow any liquids or any foreign object to enter the UPS Do not place beverages or any other liquid containing vessels on or near the unit 6 This unit intended for installation in a controlled environment temperature controlled indoor area free of conductive contaminants Avoid installing the UPS in locations where there is standing or running water or excessive humidity Do not plug the UPS input into its own output Do not attach a power strip or surge suppressor to the UPS 6 Do not attach non computer related items
7. ipment it should be assured that the sum of the leakage currents of the UPS and the connected loads does not exceed 3 5mA The mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily accessible System Description Front Panel 1 LCD Back Light 2 Power ON OFF Switch Back Panel 1 Communication Port optional 2 Modem Phone LineSurg Protection 3 AC Output 4 AC Input Installation and Operation Installing the UPS is as easy as following the steps shown Be aware of the Power Switch must be kept in the ON position otherwise the UPS will be disabled and your equipment will not be protected during a power failure 1 Inspection Remove the UPS from its packaging and inspect it for damage that may have occurred during shipping If any damage is discovered repack the unit and return it to the place of purchase 2 Placement Install the UPS unit in any protected environment that provides adequate airflow around the unit and is free from excessive dust corrosive fumes and conductive contaminants Do not operate your UPS in an environment where the ambient temperature or humidity is high On the other hand place the UPS unit away from monitor at least 20cm to avoid interference 3 Charging This unit is shipped from the factory with its internal battery fully charged however some energy may be lost during shipping so the battery should be recharged before using it
8. such as medical equipment life support equipment microwave ovens or vacuum cleaners to UPS To reduce the risk of overheating the UPS do not cover the UPS cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces Unplug the UPS prior to cleaning and do not use liquid or spray detergent Do not dispose of battery or batteries in a fire The battery may explode Do not open or mutilate the battery or batteries Released electrolyte is harmful to the skin and eyes It may be toxic A battery can present a risk of electrical shock and high short circuit current The following precautions should be observed when working on batteries 1 Remove watches rings or other metal objects from the hand 2 Use tools with insulated handles 3 Wear rubber gloves and boots 4 Do not lay tools or metal parts on the top of batteries 5 Disconnect charging source prior to connecting or disconnecting batteries terminal Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions Keep unauthorized personnel away from batteries When replacing batteries replace with the same number of the sealed lead acid batteries This pluggable type A equipment with battery already installed by the supplier is operator installable and may be operated by laymen During the installation of this equ
Download Pdf Manuals
Related Search