SF-1000R Security Smoke Generator (Wireless Control) User Manual
Contents
1. will flash When smoke liquid bladder is not installed It takes about 20 minutes for machine to complete heat up process The exact needed time depends on power offered and surrounding temperature 3 Smoke liquid bladder installation and replacement e The 500c c smoke liquid is packed by a specific bladder and it is put inside of machine upside of heater Please do plug in power before install and replace bladder By doing this the timer can be reset automatically and the timer can record the operation time and warn Low Fluid Level correctly e Please release the bag clamp and take out the old bladder when replacing bladder e Please insert the needle Fluid pipe connecter into bladder completely Note needle should go into OUT position and then place bladder into the bladder chamber well Make sure the neck of bladder reset the micro switch inside the chamber and screw the bag clamp firmly Fluid Pipe Connecter Fluid Timer Reset Micro switch 4 Function instruction e This model can be controlled by wireless control only The source of wireless control can be wireless PIR motion detector wireless window sensor and wireless remote controller etc This unit is a dual power model Therefore when the AC main power is cut off the power from UPS Un interrupted Power Supply can provide power to the PC board and pump of the unit to make it keep working However it can not provide power to heater Thus if the2. SF 1000R Security Smoke Generator Wireless Control User Manual Warning Hot nozzle Keep at least 50 cm distance from nozzle The heater of the generator is extremely hot Please be careful when the front cover is open No user serviceable parts inside Please contact with an authorized dealer when maintenance is required Please disconnect power before changing fuse Please operate only with adult supervision We X X X Only Weiyang security specific smoke liquid should be used Other fluid may damage the equipment or cause dangers to human physical safety x Do not use without smoke liquid For indoor use only Please keep dry Please clear smoke away from room after a smoke ejectment Otherwise residue might be caused Package Before starting installation Weiyang security smoke generator please make sure that you have all the following equipments 1 x security smoke generator 1 x 500c c Smoke fluid bladder 1 x Mounting set Hanging Bracket and Screws 1 x Wireless 4 key controller 1 x Wireless PIR Motion Detector 1 Prior to installation Open packing carton and check whether smoke generator and all accessories are intact Please check the technical label in the back of machine and make sure to operate the unit at rated voltage and frequency 2 Machine installation instruction Once plug in the unit the build in buzzer will Keep beeping for 30seconds Also the orange LED light in the side of machine
3. main power is cut off and the smoke machine is set off once the smoke machine can not offer second smoke output When the smoke liquid is run out the LED and buzzer will flash and beep to remind users Please see below LED and buzzer status table and stop producing smoke In order to protect pump and ensure a longer lifespan of pump x Please place a whole new full smoke liquid bladder when replacing bladders Otherwise it will cause the timer record wrong operation time and damage pump 5 Action instruction Wireless Remote Controller amp PIR motion detector The 4 key wireless remote controller In order to avoid incorrect actions caused by unintentional touch the buttons of wireless controller are designed specifically hard to press Thus please press buttons hard and press at least 2 seconds per time 1 Press AWAY key can make the machine enter guarding status LED green light flash slowly under guarding status Under guarding status the wireless PIR motion detector starts to work x Please remember to open the front cover of the PIR and switch on the PIR power 2 Press HOME key can release guarding status or stop smoke output which is triggered by PIR 3 Press PANIC key can force the smoke machine to eject smoke and press PANIC key again to stop smoke output which is set off by PANIC key 4 The UNLOCK key is the testing key Under guarding status press UNLOCK key can test the smoke machine and press HOME key to stop sm
4. oking test 5 After smoke output press AWAY key can re enter guarding status and press AWAY key and than press HOME key can enter ready status PANIC KH HOME AEA gt AWAY 3k AWAY UNLOCK UNLOCK BE dp E38 6 Inner structure design PUMP Thermostat DOWN UP PCB Fluid Bag Chamber 7 PCB Schema 24 2 5 26 Power input 1 UPS Power Neutral 2 UPS Power Line 3 AC Main Power Line 4 AC Main Power Neutral Power output 5 Heater Neutral 0 Heater Line 23 Pump Connection Fuse 24 F800MA 250V 220V 240 F1A 250V 100V 120V 25 F2A 250V 100V 120V F1A 250V 220V 240V 26 T5A 250V 220V 240V T7A 250V 100V 120V Terminals 7 Fluid Timer Reset Switch 889 Micro Switch Tamper 10 Buzzer 11 Jumper Switch off buzzer 19 Connect to Wireless Remote Receiver 13 No Function 14 Connect to Temperature Sensor Wire 15 Three color LED light 16 DIP Switch 1 amp 2 17 Button PB2 For Switching on off UPS Function For Testing 4 Setting Smoke Output Duration 20 No Function 21 Memory IC Others 22 Transformer 12 Jumper 8 Switching on off UPS Un interrupted Power Supply function Switch the DIP Switch 2 Number 16 on PCB schema to ON position the LED Number 15 on PCB schema will start to flash red and green lights together At this time keep pressing button PB2 Number 17 on PCB schema for 5 seconds can switch off
5. the UPS Un interrupted Power Supplier mode Please note if the UPS is switched off then pressing button PB2 Number 17 on PCB for 5 seconds can switch on the UPS Un interrupted Power Supply mode 9 Setting Smoke Output Duration Time Switch the DIP Switch 2 Number 16 on PCB schema to ON position the LED Number 15 on PCB schema will start to flash red and green lights together At this moment keep pressing button PB1 Number 18 on PCB schema for 10 seconds can reset the smoke output duration time The original setting is at 15 seconds per ejection Pressing PB once can add 15 seconds smoke output duration The maximum is to press 23 times PB1 to set a 6 minute non stop smoke output duration Xx Please note when switching the DIP Switch 2 Number 16 on PCB schema to OFF position the button PB 2 Number 17 on PCB schema is no function 10 Testing Machine When the machine is well installed and completes the heating process LED green light on permanently press button PB 1 Number 18 on PCB schema can test the unit Keep pressing button PB1 can make the unit eject smoke and release button PB1 to stop smoking test 11 LED amp Buzzer Status Table swr Process incomplete Long beep for 30 sec and then 3 short Permanent red beeps every 5 min DIP 2 switch DIP2switchtoON O DIP2switchtoON O No buzzer buzzer Red and green Red and green flash together Red and green flash together Thank you ver
6. y much again for your patience and reading this manual If you have any further question about our products please do not hesitate to contact your local distributor or Weiyang directly Weiyang contact information Email sales weiyang com tw Tel 886 2 2269 3323 Fax 886 2 2269 3325 No 13 Datong Street Tucheng District New Taipei City Taiwan 5
Download Pdf Manuals
Related Search