Intense PC Owners Manual
Contents
1. Intense PC Owner s Manual Intense PC Owner s Manual 01 July 2012 Introduction Package contents Hardware specifications Intense PC features Quick start guide Connecting Intense PC Booting Linux Booting Windows 7 Maintenance Opening service door Service bay BIOS Setup Utility Warranty and RMA Warranty RMA Tips for saving power General In Operating System For more information and to obtain the latest revision of this document please visit www fit pc com Introduction Package contents 3 5mm to RCA cable for S PDIF 1 Intense PC computer 2 12V DC power supply 3 AC cord Standard North American plug 4 HDMI to DVI adapter 5 6 2 WiFi antennas in some models To use Intense PC you will need e A display with DVI HDMI or DisplayPort input DVI HDMI or DisplayPort cable USB keyboard and mouse Hardware specifications CPU Chipset RAM Storage Display Audio Wireless LAN USB Serial Power Operating temperature Intel Core CPU 827E 847E i3 2340UE i7 3517UE Intel 6 7 Series System Controller Hub 2x DDR3 1333 SO DIMM sockets up to 16 GB Internal bay for 2 5 9 5mm thick SATA 3 HDD HDMI DVI DisplayPort in dual head configuration S PDIF in out 7 1 channels Stereo line out and stereo line in 802 11b g n 2 antennas BT 3 0 2x 1000BaseT RJ45 2x USB 3 0 5 Gbps 2x USB 2 0 480 Mbps 4x USB 2 0 in front RS232 full UART mini connector c2. Turn off the Intense PC Turn on while holding down the F2 key Bios Features See http fit pc com wiki index php IntensePC BIOS Documentation Warranty and RMA Warranty e CompuLab guarantees products against defects in workmanship and material for a period of 24 months from the date of shipment e Your sole remedy and CompuLab s sole liability shall be for CompuLab at its sole discretion to either repair or replace the defective product at no charge e This warranty is void if the product has been altered or damaged by accident misuse or abuse RMA Keep the original package for shipping in case of hardware failure In case of HW failure of an Intense PC under warranty please contact the seller of that Intense PC Please provide the following required information Intense PC serial number Name of purchaser e Address e Problem description If the Intense PC was purchased directly from CompuLab please email rma fit pc com Tips for saving power General e Working without a connected display automatically disables the graphics controller saving power Disconnect external USB devices when not in use In Operating System Use power scheme as follows Turn of monitor after several minutes not in use Turn off hard disk after several minutes not in use System standby after an hour not in use
3. able sold separately 12V DC 0 50 C Local resellers may supply Intense PC with other AC cord types Intense PC features On Off USB 3 RS232 eSATA HDMI S ps lt P dini WLAN Line out Line in USB2 DC12V Display GbE WLAN S PDIF out S PDIF in Port Front panel The features of the front panel of Intense PC depend on specific FACE Module used and are documented separately Power Intense PC has a tactile power push button Itis used for turning on off the PC and for standby resume when supported by the operating system A push of at least 5 seconds will always turn off the Intense PC Display Intense PC has dual display interface with support for dual head 1 Standard HDMI with audio support 2 DisplayPort To connect Intense PC to a DVI display use the provided HDMI to DVI D adapter Use a DVI cable to connect the adapter to the display To connect Intense PC to a VGA display use fit VGA sold separately Audio There are 2 standard 3 5mm jacks on the back panel Right Stereo line in using a standard 3 5mm plug S PDIF 7 1 in using provided cable Left Stereo line out using a standard 3 5mm plug S PDIF 7 1 out using provided cable LAN Intense PC features two 10 100 1000BaseT Ethernet ports using standard RJ45 connectors Use a standard Ethernet cables to connect The connectors feature built in LEDs that are lit when a connection is detected WLAN 2 WLAN antennas are suppl
4. g Windows 7 Upon first power up you will be guided through the Windows Welcome procedure which is self explanatory The Windows 7 serial number is printed on the Windows 7 label on the bottom of your Intense PC Maintenance Intense PC requires no maintenance You should not take the Intense PC apart other than opening the service door Taking Intense PC apart will void its warranty The following operations can be conducted by the user Opening service door 1 Unscrew marked Philips screw at the bottom to release service door 2 Slide out service door until it stops about 10 mm 3 Service door is now detached Lift edge of service door to completely remove Re assemble in reverse order Hard disk connects by sliding in the service door Service bay 2 The service bay provides easy access to hard disk RAM and mini PCle sockets incl WLAN module Hard disk is 2 5 9 5mm SATA It is screwed to service door by 4 screws 2 on each side It is recommended to use 5400 RPM hard disk or SSD 7200 RPM or higher is not recommended due to higher power consumption and risk of overheating RAM use DDR3 1333 SO DIMM modules Mini PCle the half size mini PCle is normally used for WLAN If you remove the WLAN module make sure to isolate the ends of antenna cables with some tape to avoid short circuit The full size mini PCle is available for any use BIOS Setup Utility Entering BIOS Setup Utility
5. ied in models with integrated WiFi and should be screwed into the standard SMA connectors USB There are 2 USB 3 0 ports 5 Gbps and 2 USB 2 0 ports on the back panel All USB ports support current up to 1A Ports on the back are upside down note when connecting USB plugs Depending on the FACE Module used some models incorporate additional 4 USB 2 0 ports in the front Serial port The RS232 mini serial port is located on the back panel Mini serial to DB9 cable to connect to standard serial devices is sold separately eSATA Intense PC features two eSATA ports Ports are located on the back panel Quick start guide Connecting Intense PC Turn off the display and connect it to the Intense PC HDMI connector use the HDMI to DVI adapter if needed e Connect the USB keyboard and mouse to USB 2 connectors Plug the Ethernet cable into the Ethernet connector e In Intense PC models with WiFi Mount the WiFi Antennas on the SMA connector by turning it clockwise repeatedly until the antenna holds firm e Insert the DC plug into the Intense PC DC in jack Rotate clockwise 90 to secure ca e Plug the speakers into the line out jack e Connect the power supply to the AC cord and plug the cord into AC outlet The front panel logo should light up as the Intense PC boots Booting Linux Linux loads automatically on power up Upon boot you will be guided through the Linux Mint first boot setup procedure Bootin
Download Pdf Manuals
Related Search