User's Guide
Contents
1. 7 Help Display No display Try recharging or replacing the battery pack Reset the units Disconnect the battery pack of the parent unit and unplug both the units electrical power then plug them back in Is the unit turned on Press and hold the ON OFF button on the parent unit to turn it ON Is the correct camera selected Change the camera number if necessary Is the video display turned on Press the VIDEO ON OFF button to turn it on When operating using batteries only the Display will go blank after 5 minutes or 50 minutes or 60 minutes to save power depending on video on setting The unit is still active and will give you audio alerts You can reactivate the screen by pressing any button Registration If the Baby Unit has lost its link with the Parent Unit Try recharging or replacing the battery pack If the Baby Unit is too far away it may be going out of range so move the Baby Unit closer to the Parent Unit Reset the units by disconnecting them from the battery and electrical power Wait about 15 seconds before reconnecting Allow up to one minute for the Baby Unit and the Parent Unit to synchronise See 2 4 Registration Pairing if there is a need to re register the units Help 19 Interference Noise interference on your parent unit Your baby and parent units may be too close Move them farther apart Make sure there is at least 1 to 1 5 metre between the 2 units to avoid audio feedback If2. motorola motorola lt User s Guide Digital Video Baby Monitor Models MBP36S MBP36S 2 MBP36S 35 MBP3S6S 4 The features described in this User s Guide are subject to modifications without prior notice Welcome to your new Motorola Video Baby Monitor Thank you for purchasing the MBP36S MBP36S 2 MBP36S 5 MBP36S 4 Now you can see and hear your baby sleeping in another room or you can monitor your older children in their playroom Please retain your original dated sales receipt for your records For warranty service of your Motorola product you will need to provide a copy of your dated sales receipt to confirm warranty status Registration is not required for warranty coverage For product related questions please call 49 0 1805 938 802 in Europe Email motorola mbp tdm de This User s Guide provides you with all the information you need to get the most from your product Before you can use the baby monitor we recommend you insert and fully charge the battery in the parent unit so that it continues to work if you disconnect it from the power supply to carry it to another location Please read the Safety Instructions on page 6 before you install the units ae everything l x Parent unit e 1x Baby unit Camera e 1x Rechargeable Ni MH battery pack 1x Power adapter for the Parent unit e 1x Power adapter s for the Baby unit In multi camera packs you will find one or more addit
3. NOTE The Monitor s power button must be turned ON and CAM pre selected before connecting the AV cable Once the AV cable is connected the Monitor s controls cannot be activated You can hear also your baby in mono mode by connecting the 3 5mm plug wired headset to the AV OUT socket Getting Started 11 5 Using the Baby Monitor 5 1 Setting up Place the baby unit in a convenient location e g on a table and point the camera lens towards the area you want to monitor Adjust the baby unit s head angle by rotating the camera up down left and right until you are satisfied with the image in the parent unit NOTE Do not place the baby unit within the baby s reach If there is interference with the picture or sound try moving the units to different locations and ensure they are not close to other electrical equipment 5 2 Panand Tilt The camera can be remotely controlled from the parent unit 1 Press the A UP button or VW DOWN button to tilt upward or downward 2 Press the lt q LEFT button or RIGHT button to pan left or right 5 5 Night Vision Mode The baby unit has 8 high intensity infrared LEDs for picking up clear images in the dark When the built in photo sensor on the top of the unit detects a low level of ambient light the LEDs will automatically activate and the screen on the parent unit will display in black and white The icon will be displayed at the top of the screen 5 4 Talk Mode Press and
4. and press the OK button to confirm 4 caml cam2 cam3 cam4 will pop up press the amp UP button or W DOWN button to select the desired Camera and press the OK button to delete that registration Note You are not allowed to delete the camera if there is only one registered camera in the system 4 6 5 Scan camera l Press the button and the menu bar will pop up 2 Press the lt q LEFT button or B RIGHT button until is highlighted and the del add view scan menu will pop up 3 Press the amp UP button or W DOWN button to select scan and press the OK button to confirm 4 The screen will then display images from different registered cameras ina loop of cam l cam2 cam3 cam4 changing about every 12 seconds TIP Quick Method to View Cameras instead of entering into the menu bar Directly press OK repeatedly to select cam 1 cam 2 cam 3 cam 4 scan 4 7 Temperature 1 Press the button and the menu bar will pop up 2 Press the lt 4 LEFT button or B RIGHT button until is highlighted 3 Press the A UP button or VW DOWN button to select C or F 4 8 Power Saving mode 1 Press the button and the menu bar will pop up 2 Press the lt q LEFT button or B RIGHT button until is highlighted 3 Press the A UP button or VW DOWN button to select auto video off after o mins 50 mins or 60 mins if not in charging 16 Parent Unit Menu Options 5 Disposal of The Device environment At the end of the
5. Do not install the baby monitor near a heat source Safety Instructions 7 Only use the chargers and power adapters provided Do not use other chargers or power adapters as this may damage the device and battery pack Only insert a battery pack of the same type Do not touch the plug contacts with sharp or metal objects CAUTION Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to their instructions 8 Safety Instructions 2 Getting Started Baby Unit Power Supply ig Connect the small plug of the power adapter to the baby unit camera and the other end to a suitable mains power socket NOTE Only use the enclosed power adapter 5V DC 1000mA 2 Slide the ON OFF switch to the ON position The power LED will light up in green 3 Slide the ON OFF switch to the OFF position to turn the Baby Unit off Parent Unit Battery Installation Red AC Insert the wire tab of the rechargeable battery pack into the contact slot as shown above and fit the battery pack into the compartment Replace the battery cover over the compartment and gently tighten the screw in a clockwise direction using a Small cross head or Flat end screw drivers Getting Started 9 2 5 Parent Unit Power Supply IMPORTANT Installing the rechargeable battery pack and charging it fully before use is recommended Thi
6. and press the OK button to start searching for a camera unit The green audio level LED will flash rapidly while searching 5 Press and hold the PAIR button underneath the baby unit until the parent unit finds the camera beeps and the picture from the camera appears NOTE A camera can only be registered to one parent unit at any one time 4 6 2 View a camera 1 Press the button and the menu bar will pop up 2 Press the lt q LEFT button or B RIGHT button until is highlighted and the del add view scan menu pops up 3 Pressthe A UP button or YW DOWN button to select view and press the OK button to confirm 4 caml cam2 cam3 cam4 will pop up press the A UP button or W DOWN button to select desired Camera and press the OK button to view the picture from that camera TIP Quick Method to View Cameras instead of entering into the menu bar Directly press OK repeatedly to select cam 1 cam 2 cam 3 cam 4 scan 4 6 5 View multi cameras on screen 1 Press the button and the menu bar will pop up 2 Press the lt q LEFT button or B RIGHT button until SH icon is highlighted 3 Press the A UP button or YW DOWN button to select 4 split screen On Off Parent Unit Menu Options 15 4 6 4 Delete a camera 1 Press the button and the menu bar will pop up 2 Press the lt q LEFT button or B RIGHT button until is highlighted and the del add view scan menu will pop up 3 Press the A UP button or Y DOWN button to select del
7. ea eo Pee ene ar EN et meee Ae Oe pee e mec 13 WA sO Ol nrn e re as N E aa rca d eee ea ieeac tart tance 15 a E dG EEPE AE E E EE EEE EE 13 4 6 Camera Control ha eenccartiiaaeceasecanta pan as dasth tela bia cee eth iaaenemdleeateneuseencls Canta 14 4 6 1 Add pair a camera sessessssessesssssesesssssesessssserossssssseessssseeessssss 14 4 6 2 NF TSA Sei came e ere Ee EE EE E 14 4 6 5 View multi cameras ON SCreen essessesessesssescssssssresessseresssseseeesess 14 4 6 4 Delete a tamera sses hoa teestead a retarncachsesuestladuuactac ad utarennuatetaaeus 15 4 6 5 SCAG AS ee ETEA EEEE E EEEE EAEE E EER 15 4 7 WG 1c gt peer ee tre ere eer nr eR ast ate are er eee nT Aare OR Re 1d AB IPGWEF SAVING INOS vieccsvecsesanssaczenraagessasadedanss osduntaag aE iaa ea a eoria 15 5 Disposal of The Device environment sssssseesseesossssssessessscosseecesesssss 16 po fame Gi 1d 0 eran N E R E E SS 17 Da THEN o PAI EEE ENE TT EAE 18 8 Generallnformation ssssssssseooossssssssseeessecccoeccccossssseesssesssessseceeceesseesssss 20 Table of contents 5 1 Safety Instructions N WARNING STRANGULATION HAZARD Keep the unit and adapter cord more than 1 metre from the cot and out of the baby s reach NEVER place camera or cords within the cot Secure the cords more than 1 metre away from the baby s reach Never use extension cords with AC Adapters Only use the AC Adapters provided
8. the baby unit is too far away it may be out of range so move the baby unit closer to the parent unit Make sure the baby and parent units are not near other electrical equipment such as a television computer or cordless mobile telephone Use of other 2 4 GHz products such as wireless networks Wi Fi routers Bluetooth systems or microwave ovens may cause interference with this product so keep the baby monitor away at least 1 5m 5ft from these types of products or turn them off if they appear to be causing interference If the signal is weak try moving the Parent and or Baby Unit to different positions in the rooms Help 8 General Information If your product is not working properly 1 Read this User s Guide or the Quick Start Guide 2 Contact Customer Service 49 0 1805 958 802 in Europe Email motorola mbp tdm de To order a replacement battery pack contact customer service Consumer Products and Accessories Limited Warranty Warranty Thank you for purchasing this Motorola branded product manufactured under license by Binatone Electronics International LTD BINATONE What Does this Warranty Cover Subject to the exclusions contained below BINATONE warrants that this Motorola branded product Product or certified accessory Accessory sold for use with this product that it manufactured to be free from defects in materials and workmanship under normal consumer usage for the period outlin
9. 36S 3 MBP36S 4 Country of Origin China Brand Motorola complies with the essential protection requirements of R amp TTE Directive 1999 5 EC on the approximation of the laws of the Member States relating to Radio Spectrum Matters the Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility EMC and the European Community Directive 2006 95 EC relating to Electrical Safety Directive 2011 65 EC on the restriction of use of hazardous substances RoHS and 2009 125 EC relating to ecodesign requirement for Energy Related Products ErP Assessment of compliance of the product with the requirements relating to the essential requirements according to Article 3 R amp TTE was based on Annex III of the Directive 1999 5 EC and the following standard Radio Spectrum EN300328 V1 7 1 2006 10 EN62311 2008 EMC EN301489 17 V2 2 1 2012 09 EN301489 1 V1 9 2 2011 09 Electrical Safety IEC60950 1 2005 Second Edition Am 1 2009 RF Safety EN62311 2008 The product is labelled with the European Approval Marking CE as show Any Unauthorised modification of the product voids this Declaration Manufacturer Importer Signature of m K i London 20 April 2014 Kad Heinz Mueller Chief Technical Officer Place amp Date General Information 25 Technical Specifications Baby unit Frequency 2 4 GHz to 2 48 GHz Image sensor color CMOS 0 5M Pixels Lens f 2 9mm
10. CAMERA SET UP amp USE Determine a location for the Baby Unit that will provide the best view of your baby in his her cot Place the BABY UNIT ona flat surface such as a dresser bureau or shelf or mount the Unit to a wall securely using the keyhole slots under the stand NEVER place the Baby Unit or cords within the cot Do not place the Baby Unit or cords in the cot or within reach of the baby the unit and cords should be more than 1 metre away WARNING This digital video baby monitor is compliant with all relevant standards regarding electromagnetic fields and is when handled as described in the User s Guide safe to use Therefore always read the instructions in this User s Guide carefully before using the device Adult assembly is required Keep small parts away from children when assembling This product is not a toy Do not allow children to play with it This baby monitor is not a substitute for responsible adult supervision Keep this user s guide for future reference Do not place the baby unit or cords in the cot or within reach of the baby the unit and cords should be more than 1 metre away Keep the cords out of reach of children Do not cover the baby monitor with a towel or blanket Never use extension cords with power adapters Only use the power adapters provided Test this monitor and all its functions so that you are familiar with it prior to actual use Do not use the baby monitor near water
11. F 2 8 IR LED 8 pcs Power Adapter Ten Pao International Ltd S006MV0500100 Input 100 240V 90 60HZ 500mA Output 5 0V 1000mA OR Adapter Kuantech Incorporated Company KSAS0050500100VED Input 100 240V 50 60Hz 500mA Output 5 0V 1000mA WARNING Use only with supplied power supply 26 General Information Parent unit Frequency Display Display colors Brightness control Volume control Power General Information 2 4 GHz to 2 48 GHz 5 0 diagonal TFT LCD 16 7M color LCD 8 steps 8 steps Adapter Ten Pao International Ltd S003IV0500060 Input 100 240V 90 60Hz 150mA Output 5 0V 600mA OR Adapter ShenZhen Frecom Electronic Co LTD FOSW 050060SPAV Input 100 240V 90 60Hz 150mA Output 5 0V 6 00mA WARNING Use only with provided power supply Battery GPI GPRHCH938C021 Ni MH AAA 3 6V 900mAh rechargeable battery pack OR Battery JUSTHIGH Ni MH AAA 35 6V 900mAh rechargeable battery pack WARNING Do not use non rechargeable batteries for the Parent Unit Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the instructions AA motorola Manufactured distributed or sold by Binatone Electronics International LTD official licensee for this product MOTOROLA and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings LLC and are used under license All other trademarks are the property
12. ed below This Warranty is your exclusive warranty and is not transferable Who is covered This Warranty extends only to the first consumer purchaser and is not transferable What will BINATONE do BINATONE or its authorized distributor at its option and within a commercially reasonable time will at no charge repair or replace any Products or Accessories that does not conform to this Warranty We may use functionally equivalent reconditioned refurbished pre owned or new Products Accessories or parts General Information DI What Other Limitations Are There ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY OTHERWISE THE REPAIR OR REPLACEMENT PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INNO EVENT SHALL MOTOROLA OR BINATONE BE LIABLE WHETHER IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR ACCESSORY OR FOR ANY INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS LOSS OF INFORMATION OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW Some
13. es adapter is plugged in 2 4 Registration Pairing The Baby monitor is pre registered to your Parent Unit You do not need to register it again unless the Baby Unit loses its link with the Parent Unit To re register your Baby Unit or register a new Baby Unit follow the procedure below l Press the button of the parent unit and the menu bar will pop up 2 Press the lt d LEFT button or B RIGHT button until is highlighted and the del add view scan menu will pop up 3 Press the A UP button or YW DOWN button to select add and press the OK button to confirm 4 caml cam2 cam3 cam4 will pop up press the A UP button or W DOWN button to select the desired Camera and press the OK button to start searching for a camera unit The green audio level LED will flash rapidly while searching 5 Pressthe OK button to confirm 6 Press and hold the PAIR button underneath the baby unit until the parent unit finds the camera beeps and the video from the camera appears NOTE Ifa particular Baby Unit was registered previously registering this current Baby Unit again will overwrite the old registration 2 5 View Video Through TV Connect a suitable AV cable into the AV OUT socket on the side of the Parent Unit and into the AV input of the TV Scroll to select GJ on the Parent unit Scroll through the AV inputs on the TV menu until the Baby monitor picture is visible AV cable is an optional accessory which is to be purchased separately
14. he Baby Unit to different positions in the rooms Table of contents l Safety Instructions cccccccccsscssccssssssssssssscessssccccecccccceeeeeeceecsessssssessseeeecs 6 2 Getting Stare Ces cciececsscescecesledesdeesassnacsecciocec ce ueansaavoutacnzseesiansecs eine awe 8 2 1 Baby Unit Power Supply vessel esas sxsesvedsosecivus sca tnuenelscuconcsapesevesbavioerstecoueenseees 8 2 2 Parent Unit Battery Installation asics iscsdhcccssatdccisvswcasbesdhvsonsdacssteomoaioatseosaeas 8 2 5 Parent Unit Power Supply s ssesssssesssssessssesssseessseeessseesssseessseeessseeessseeeeseeesss 9 24 R gistrahon PaO ae aart AEEA A EE aA aA ELEA 10 ZO View Video Through TV sessssssssssesesssesssesessseeessssessseeeseseeessseeesseeeseseeessseees 10 5 Using the Baby Monitor essseeeeesssosssssssessssesssccccosessesssssesessecosseeceeesssss 11 e 1112EAN 11 R PAG It E E A EE IAE AEE E AEE EEO AAT EE EEEE AEE EEE 1l Oro NightVision Mode esssssssesessssrserssseseecessssrseessssrecessseseesesssseeeesessseeeesesseee 11 SA STIG CS sees ua vice ies a a E esne es euaeoveee Canoe ll o ERON rics E EE OE E EAE AA E EEE 11 5 6 Temperature Display HH C F or LL C F uu ce eescsscesscreescsreessones 12 4 Parent Unit Menu ODtionsS cccccccccessscessssssssscessceccecceeeeeeeesesssssssseeeecs 13 A VOUE soinen a a a aeaa Te gent iors 15 A Ee AE e E E E EEE EEE E OEE EEEE EEEE 13 LO Yam SU E o eee reer aaa tery Ua
15. hold the amp TALK button on the parent unit to talk to your baby through the baby unit s loudspeaker The amp icon will be displayed at the top of the LCD screen 5 5 Video ON OFF Press VIDEO ON OFF key to turn the LCD display on or off but still leave the audio monitor on 12 Using the Baby Monitor 5 6 Temperature Display HH C F or LL C F The temperature reading from the temperature sensor at the back of the Baby Unit will be displayed at the top of the LCD screen The readings will turn RED if the temperature goes above 29 C 84 F or below 14 C 57 F The reading will change to HH C F if the temperature goes above 56 C 97 F The reading will change to LL C F if the temperature goes below 1 C 34 F Using the Baby Monitor 4 Parent Unit Menu Options 4 1 Volume 1 Press the button and the menu bar will pop up 2 Press the lt q LEFT button or B button until d is highlighted 3 Press the A UP button or YW DOWN button to select the desired volume level from level 0 8 The default volume level setting is level 4 2 Brightness Press the lt LEFT button or B button until 20 is highlighted Press the A UP button or W DOWN button to select the desired brightness level from level 1 8 The default brightness level setting is level 5 4 5 Lullaby 1 Press the button and the menu bar will pop up 2 3 4 1 Press the button and the menu bar will
16. ional camera units with power adapter units and battery packs Overview of the Parent Unit Display LCD screen Up Key A Normal Mode Tilt Up Menu Mode Up Down Key Y Normal Mode Tilt Down Menu Mode Down Left Key lt q Normal Mode Pan Left Menu Mode Left Right Key B Normal Mode Pan Right Menu Mode Right Menu Key Press to open the Menu options OK Key OK Video ON OFF Key Q Press to turn OFF the LCD display Press again to turn ON the LCD display Parent unit menu icons Signal Level 5 Levels Night Vision Mode Screen changes to Black White Talk Mode Battery Level Control 4 Levels 11 12 13 14 15 Talk Key amp Press and hold to speak to your baby Power Adapter Battery LED BLUE when mains adapter power on RED when battery low Unit ON OFF LED Green Audio Level LED Green Orange Red Red Microphone Power Key Press and Hold to turn the unit ON OFF Antenna Lift the antenna for optimal reception Battery cover Stand Speaker USB power adapter socket AV out Audio out Parent unit menu icons cont d Volume Level Control 8 Levels Zoom Level Control LX 2X Brightness Level Control 8 Levels Lullaby Control 5 Song Selections Alarm Setting 6h 4h 2h Off X Temperature Reading HH C F or LLOC F Icon amp readings turn RED gt 29 C 84 F and reading display HH C F gt 56 C 97 F Icon amp
17. jurisdictions do not allow the limitation or exclusion of incidental or consequential damages or limitation on the length of an implied warranty so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights that vary from one jurisdiction to another 22 General Information Products Covered Length of Coverage Consumer Products Two 2 years from the date of the products original purchase by the first consumer purchaser of the product Consumer Accessories Ninety 90 days from the date of the accessories original purchase by the first consumer purchaser of the product Consumer Products and Accessories The balance of the original warranty or that are Repaired or Replaced for Ninety 90 days from the date returned to the consumer whichever is longer Exclusions Normal Wear and Tear Periodic maintenance repair and replacement of parts due to normal wear and tear are excluded from coverage Batteries Only batteries whose fully charged capacity falls below 80 of their rated capacity and batteries that leak are covered by this Warranty Abuse amp Misuse Defects or damage that result from a improper operation storage misuse or abuse accident or neglect such as physical damage cracks scratches etc to the surface of the product resulting from misuse b contact with liquid water rain extreme humidity or heavy perspiration sand di
18. of their respective owners 2014 Motorola Mobility LLC All rights reserved CE Version 1 0 Printed in China
19. pop up 2 3 Press the lt Q LEFT button or button until JJ is highlighted Press the UP button or Y DOWN button to select the desired song from the 5 lullabies available or the cycle option to play all 5 songs in turn If an individual song is selected it will only play once The default setting is lullaby OFF 4 Press OK on the selected lullabies to select the desired song sound level 44 Zoom 1 Press the button and the menu bar will pop up 2 Press the lt Q LEFT button or B button until is highlighted 3 Press the A UP button or Y DOWN button to select the 1X or 2X Zoom The default setting is 1X Alarm 4 1 Press the button and the menu bar will pop up 2 Press the lt d LEFT button or B RIGHT button until is highlighted 3 Press the A UP button or VW DOWN button to select the alarm time 6h 4h 2h The default setting is Alarm OFF 4 fanalarm time is selected the parent unit will beep for about 45 seconds after every 6 4 or 2 hour period 14 Parent Unit Menu Options 4 6 Camera Control 4 6 1 Add pair a camera 1 Press the button and the menu bar will pop up 2 Press the lt q LEFT button or B RIGHT button until is highlighted and the del add view scan menu will pop up 3 Press the A UP button or Y DOWN button to select add and press the OK button to confirm 4 caml cam2 cam3 cam4 will pop up press the A UP button or W DOWN button to select the desired Camera
20. product lifecycle you should not dispose of this product with normal household waste Take this product to a collection point for the recycling of electrical and electronic equipment The symbol on the product user s guide and or box indicates this Some of the product materials can be reused if you take them to a recycling point By reusing some parts or raw materials from used products you make an important contribution to the protection of the environment Please contact your local authorities in case you need more information on the collection points in your area Dispose of the battery pack in an environmentally friendly manner according to your local regulations Disposal of The Device environment 17 6 Cleaning Clean the MBP36S MBP36S 2 MBP36S 3 MBP36S 4 with a slightly damp cloth or with an anti static cloth Never use cleaning agents or abrasive solvents caning and care Do not clean any part of the product with thinners or other solvents and chemicals this may cause permanent damage to the product which is not covered by the warranty Keep your MBP36S MBP36S 2 MBP36S 3 MBP36S 4 away from hot humid areas or strong sunlight and don t let it get wet Every effort has been made to ensure high standards of reliability for your MBP36S MBP36S 2 MBP3S6S 5 MBP36S 4 However if something does go wrong please do not try to repair it yourself contact Customer Service for assistance 18 Cleaning
21. readings turn RED lt 14 C 57 F and reading display LLOC 9F lt 1 C 34 F Cam Control scan view add delete E Screen viewing mode control Single Screen 4 split Screen Q Set Video On Timer 5 min 50 min 60 min Overview of Your Baby Unit 1 Photo Sensor 6 Speaker Night Vision Mode 7 ON OFF Switch 2 Camera Lens 8 Power Adapter Socket Infrared LEDs 9 Antenna 4 Power LED 10 Temperature Sensor 5 Microphone 11 Pair Key Important guidelines for installing your Baby Monitor To use your Video Monitor Baby and Parent Units together you must be able to establish a radio link between them and the range will be affected by environmental conditions Any large metal object like a refrigerator a mirror a filing cabinet metallic doors or reinforced concrete between the Baby and Parent Unit may block the radio signal The signal strength may also be reduced by other solid structures like walls or by radio or electrical equipment such as TVs computers cordless or mobile phones fluorescent lights or dimmer switches Use of other 2 4 GHz products such as wireless networks Wi Fi routers Bluetooth systems or microwave ovens may cause interference with this product so keep the baby monitor away at least oft 1 5m from these types of products or turn them off if they appear to be causing interference If the signal is weak try lifting up the Parent Unit Antenna moving the Parent and or t
22. rt or the like extreme heat or food c use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions or d other acts which are not the fault of MOTOROLA or BINATONE are excluded from coverage Use of Non Motorola branded Products and Accessories Defects or damage that result from the use of Non Motorola branded or certified Products or Accessories or other peripheral equipment are excluded from coverage General Information 23 Unauthorized Service or Modification Defects or damages resulting from service testing adjustment installation maintenance alteration or modification in any way by someone other than MOTOROLA BINATONE or its authorized service centres are excluded from coverage Altered Products Products or Accessories with a serial numbers or date tags that have been removed altered or obliterated b broken seals or that show evidence of tampering c mismatched board serial numbers or d nonconforming or non Motorola branded housings or parts are excluded from coverage Communication Services Defects damages or the failure of Products or Accessories due to any communication service or signal you may subscribe to or use with the Products or Accessories is excluded from coverage How to Obtain Warranty Service or Other Information To obtain service or information please call 49 0 1805 958 802 in Europe Email motorola mbp
23. s will allow the unit to operate on battery in the event of a power failure 1 Connect the small plug of the power adapter to the parent unit and the other end to a suitable mains power socket Only use the enclosed power adapter OVDC 600mA with the slightly smaller DC plug 2 Press and hold the POWER ON OFF button for 1 second to turn ON the parent unit 3 Once the baby and parent units are switched on the display on the parent unit will show the video captured by the baby unit 4 lf there is no connection or you are out of range the video display will go off and the unit will beep every 5 seconds Move the parent unit closer to the baby unit until the link is re established 5 Press and hold the POWER ON OFF button until the progress bar finishes scrolling to turn OFF the parent unit NOTE The battery icon L_ turns RED to indicate that the battery is low and it gives a beep every 16 seconds The battery needs to be recharged The battery pack takes about 12 hours to charge fully When charging 1 During power OFF when adapter is plugged in a adapter logo will display on screen and then a flashing battery logo will display for 45 sec The Blue LED at top left corner light up indicates adapter is plugged in 10 Getting Started 2 During power ON when adapter is plugged in the battery icon on screen s top right corner will show that the battery is charging The Blue LED at the top left corner light up indicat
24. tdm de You will receive instructions on how to ship the Products or Accessories at your expense and risk toa BINATONE Authorized Repair Centre To obtain service you must include a the Product or Accessory b the original proof of purchase receipt which includes the date place and seller of the Product c if a warranty card was included in your box a completed warranty card showing the serial number of the Product d a written description of the problem and most importantly e your address and telephone number These terms and conditions constitute the complete warranty agreement between you and BINATONE regarding the Products or Accessories purchased by you and supersede any prior agreement or representations including representations made in any literature publications or promotional materials issued by BINATONE or representations made by any agent employee or staff of BINATONE that may have been made in connection with the said purchase 24 General Information BINATONE TELECOM PLC 1 Apsley Way London NW2 7HF United Kingdom Tel 44 0 20 8955 2700 Fax 44 0 20 8344 8877 na one e mail binatoneuk binatonetelecom co uk EC Declaration of Conformit We the manufacturer Importer Binatone Telecom Plc 1 Apsley Way London NW2 7HF United Kingdom Declare under our sole responsibility that the following product Type of equipment Digital Video Baby Monitor Model Name MBP36S MBP36S 2 MBP
Download Pdf Manuals
Related Search