LightSYS Quick User Guide
Contents
1. SECURITY PERTH 9313 1881 Light syS Quick User Guide Thank you for choosing LightSYS intruder control panel This quick start guide describes the main user operating actions of the LightSYS To view the full version of the user manual please refer to our website www riscogroup co uk Full Set Part Setting System Unset and Silence an Alarm Partition Full Setting Partition Part Set Partition Unset Duress Unset Panic Alarm Fire Alarm Medical Alarm Quick Omit Zones Activate Output Define Follow Me View Fault View Event Log Keypad Chime On Off Edit User Code Zone Testing Walk Test Code gt _ Code gt LE Code gt aly Code gt n gt Partition No gt a Code gt LE gt Partition No gt ue Code gt al Partition No gt Duress Code gt a ail a Pressing simultaneously for 2 seconds Pressing F simultaneously for 2 seconds amp To lt P Pressing simultaneously for 2 seconds Code gt Zone No Output Control i P iCode Cy Follow Me fal SE Code G7 Activities G2 Define as Code ay View ay Fault ay lt p Code Oy Event Log al 1 Code 7 Activities al Keypad sound al Chime a Code ay Codes Tags dz Define D Code Ch Maintenance C is Walk Test LightSYS Quick User Guide 1 Lignt SYS SECURIT 9313 1881 Indicators g Set RED LED icy Part set Omit Power On System ar2. ating the Menu Returning to previous menu 5IN1539 B 4 LightSYS Quick User Guide
3. ey to toggle among the choices 5 Press to save your settings SMS Control Commands Controlling the System through SMS Note Available only if your LightSYS is equipped with the GSM module Operation SMS Message Structure Example Set all partitions of a user code Code S 1234S Set all partitions to Part Setting Code P 1234P Unset all partitions of a user Code US 1234US code Set by partition Code S Partition No 1234S Part set by partition Code P Partition No 1234P1 Unset by Partition Code US Partition No 1234US1 Omit a zone Code OM zone number 12340M05 Un omit a zone Code UNOM zone No 1234UNOM05 Activate Output Code POON PO No 1234POON1 Deactivate Output Code POOFF PO No 1234POOFF1 Change FM number Code FMPHONE FM serial number 1234FMPHONE 3 NEW New Phone No NEW0529692345 Get system status Code ST 1234ST Get last alarm memory Code AL 1234AL Get SIM credit level for Code CR 1234CR prepaid cards Examples To set the system send SMS 12345 To set partition 1 and 2 send SMS 1234512 To unset partition 1 send SMS 1234US1 1 Command words are not case sensitive they can contain both capital small or mixed letters 2 A separator between command words is not required although it is accepted 3 Default grand master code is 1234 LightSYS Quick User Guide 3 Light sy S SECURIT Yi PERTH 9313 1881 Telephone Control Commands Remark Available on
4. ly if your LightSYS is equipped with the voice module Receiving a call 1 Pick up the phone 2 Say Hello or press You will hear an event announcement message 3 Choose an option from the Acknowledgment menu Calling the System 1 Dial the number of the premises R2 e If an answering machine is present at the premises Let the line ring once hang up and call again If an answering machine is not in use at the premises the system will answer and you will hear a solid tone 2 Enter a 2 digit remote access code immediately after the tone 3 Enter your user code followed by 4 Choose your option from the Operations menu RISCO Group 05 2011 Acknowledgment menu Acknowledge message 1 Acknowledge and stop all dialing 2 User code Enter Operations menu 3 User code Listen In and Talk 6 3 User code Repeat the event message Repeat the Acknowledgment menu Operations Menu Setting all Partitions 1 1 Setting by Partition 1 9 Partition no Unsetting by Partitions 2 2 Unsetting by Partition 2 9 Partition no Omitting Zone Definition 3 Zone no 9 Operating Programmable Outputs 4 PO no Changing FM Numbers 5 FM no 2 New phone no 1 Listening in 6 1 Talking 6 2 Listening in and Talking 6 3 Recording a Messages 7 Exiting the System 0 Repe
5. med Full On System armed at Part On Power OK No faults or Part set set Omitted zones in the Off No power Off System unset system Rapid Flash System fault Slow Flash System isin Off No omit zones Exit Delay vV Ready Rapid Flash Alarm h On Ready to set Fire Off Not ready to set TN On Fire alarm Slow Flash Ready to set with Tamper Off No fire alarm open Exit Entry zone On Tamper alarm Flash Fire fault Off No tamper alarm Edit User Code From the main display press a Enter master code Default code 1234 followed by ar 2 Scroll to the option Codes Tags gt ay Scroll to Define and press CH Select a user and press 9 Select Edit Code and press ay Enter the new code followed by el To edit user label scroll to Edit Label and enter label Repeat the above steps for additional codes Assign Proximity Tag 1 Follow steps 1 5 of the Edit User Code above Select Re Write tag press al a Within 10 seconds approach the proximity tag to the keypad LightSYS Quick User Guide LightSYS Flexible Hybrid System Setting and Changing System Time and Date SECURIT Yet PENITI 9313 1881 1 Press T and enter grand master code followed by GD 2 Using the arrow keys scroll to the option Clock and press 3 The display will show Time and Date Press 4 Enter the correct time in 24 hour format and date For entering the date use the Rr keys to move the cursor and the 2oy amp k
Download Pdf Manuals
Related Search