CM67NG user guide (Int English).p65
Contents
1. really require it Honeywell COV RF Chronotherm What is an RF Chronotherm A Honeywell Radio Frequency RF communicating Chronotherm is a programmable thermostat that controls your heating system so that you can have comfortable temperatures when you are at home and energy savings when you are out With RF communication there is no need to provide wired connection between thermostat and boiler The Chronotherm can therefore be installed without disrupting your room decor Instead of wired connection the Chronotherm sends a radio frequency signal directly to the relay box installed next to the boiler These instructions explain how to program and operate your Chronotherm to get the most comfort at the least cost What will the CM67NG Chronotherm do for me Wireless connection to the boiler allows you to mount the Chronotherm in your room without decor disruption Armchair programming feature lets you program your Chronotherm while resting comfortably in your armchair Attractive slim styling makes it ideal for location in any room in your home 7 day program lets you set the CM67NG to match your weekly lifestyle 6 daily independent temperature levels let you set any 6 temperatures from 5 to 30 C at any time each day to match your daily lifestyle Party button lets you temporarily maintain or adjust the current temperature for 1 23 hours Useful when you have friends round or go out of the hous2. display indicating they can be changed 2 Press the or button until the correct time is displayed Each button press will change the time by one minute and stop the display from flashing Holding the button down for a few seconds will change the time slowly at first then quickly 3 Press the DAY 1 7 button until the day marker is positioned under the correct day DAY 1 is Monday Each button press moves the day marker by one day How do I get started with the built in tempera ture program Move the slider to the AUTOmatic position The Chronotherm will now control your heating using the built in temperature program Monday to Friday Program 1 2 3 4 5 6 Time 06 30 08 00 12 00 14 00 18 00 22 30 Temperature 21 C 18 C 21 C 18 C 21 C 16 C Program 1 2 3 4 5 6 Time 08 00 10 00 12 00 14 00 18 00 23 00 Temperature 21 C 21 C 21 C 21 C 21 C 16 C How do I set my own temperature program for each day of the week 1 Move the slider to the PROGram position You will see the first temperature change time and temperature level for Monday s program the two small arrows are displayed only when the programmed temperature level is shown The flashing display indicates that you can make changes DAY L gt PROG AUTO TNN pa l re MAN JEE AT OFF 2 Press the or button to adjust the first temperature change time Holding the button down wil
3. holiday days counter will be reduced by one until the selected number of days have passed The unit will then return to normal control as set by the MANual or AUTOmatic slider position To cancel the HOLIDAY setting press the I button a second time or move the slider How can I switch the RF Chronotherm off Move the slider to the OFF position The unit has an intelligent built in frost protection feature so that if the temperature falls below 5 C it will automatically switch back on to prevent your pipes from freezing How do know when the batteries need changed and how do I change them Your RF Chronotherm has built in electronics that constantly monitor the battery power level With no other accessories fitted the batteries should last about 3 years When the batteries need replaced a flashing symbol will be displayed To change the batteries 1 Lift up the front flap to reveal the battery compartment Open the battery compartment by inserting a coin underneath the bottom right edge of the flap and lift it out 2 Replace the used batteries with 2 new AA LR6 Alkaline Batteries Duracell are recommended and push the battery compartment firmly back into the front of the unit RESPECT YOUR ENVIRONMENT Take care to dispose of used batteries carefully The RF Chronotherm has a permanent memory to keep your program settings while you change the batteries you should never need to reprogram However if you take more tha
4. When do I need to use the push button During the normal system operation there is no need to use HC60NG push button You can control your boiler manually using your CM67NG room unit 1 Move the slider to the MAN position 2 Switch the boiler ON or OFF by pressing the TEMPerature or w button to increase or decrease the programmed temperature You should use the push button to control your_ boiler only when the radio frequency communication is lost see the CM67NG Trouble Shooting Guide Automatic Time Setting ATS Add On Module The ATS module picks up a daily time signal from a transmitter in Central Europe and corrects the time on the RF Chronotherm display So e You never need to set or adjust the time e There is no need to adjust the unit by 1 hour in summer winter since the unit does this automatically e Your Chronotherm is the most accurate clock in your home so you can use this information to set up all your other clocks Not available in all Geographic Regions depending on transmitter range and home location Can use my Chronotherm to control my air conditioning system Yes Please refer to your installer for more information How can I enhance comfort and save energy with Honeywell RF multi zone system We are quite used to switching the lights on in our houses using individual switches in every room It is common that we even use more than one light switch to control the lights in t
5. but heating does not Boiler switched off switch on HC60NG LEDs are off or green one is on Wrong electrical connection HC60NG red LED is constantly on or RF communication lost due to the flashing wrong location of the room unit RF communication fault Heating switches on or off too slowly or too quickly Temperature swings between too hot and too cold Display show spanner symbol Fault in the Chronotherm What is required to install a zoning system First your heating system has to be laid out in a way that allows control of the heat supply to a zone by means of zone valves or pumps see drawing ask you installer for details If this condition is fulfilled the rest is easy Ask your installer to add additional zone controller s and a boiler controller Zone 2 Multi zone System Plan Note You can extend the system to control up to 4 zones Remedy Check that the batteries are in the battery compartment and that the paper tab has been pulled out Check that the batteries have been installed in the correct orientation Replace batteries Remove battery compartment and re insert Change batteries as described previously The heat demand is send to the relay box as a value between 0 100 The relay box will adjust the boiler on time to meet this requirement That is why the heating will be off sometimes even if the flame symbol is displayed To check if RF system is communicating properly press the TEMPeratu
6. e for a short while Day Off button copies Sunday s program into tomorrow so that you can make the CM67NG follow the Sunday program if you have a day off during the week Holiday button saves energy by letting you reduce the tempera ture for 1 to 99 days while you are on holiday returning to normal operation on the day you return Memory holds the user program indefinitely so that it is never lost even if you remove the batteries How do install the batteries 1 Lift up the front flap to reveal the battery compartment Open the battery compartment by inserting a coin underneath the bottom right edge of the flap and lift it out 2 Pull the paper tab out to activate the 2 AA LR6 Alkaline Batteries included and push the battery compartment firmly back into the front of the unit After a pause the unit will now display information 42010476 001 R1 CM67NG Controls Display Layout The diagram below details the key button functions and display information Battery Low Day Marker Time Display Heat Demand Temperature Indicator Indicator Display Day Information Button Enquiry Button Copy Day Button Temperature Change Time Buttons Change dy increase Buttons WW decrease Battery Setting Compartment Slider Party Button Day Off Button Holiday Button Program Buttons How do I set the time and day 1 Move the slider to the DAY position The time and day marker will now be flashing on the
7. he room Yet we still expect that one room thermostat will control heating in the entire house providing comfort for all inhabitants and maximum energy efficiency of the heating system Certainly just one room thermostat can not meet these requirements To address the needs of modern households Honeywell developed FCM60NG simple and practical heating controller for up to 4 zones Why do I need a multi zone system We can all distinguish at least two functional zones in our houses A day time zone where we spent our time when we are active and the night zone where we sleep Sometimes we can define more zones e g study zone or teenager s zone This functional division of the house into zones dictates the need for different temperatures at different times of the day Therefore our heating control system should allow us to set and program temperatures individually for each zone What if something happens to my heating system How can check that the Chronotherm is working See the troubleshooting guide below If you need assistance after this call your installer T CM67NG Trouble Shooting Guide Symptom Possible Cause Blank display No batteries Wrong battery orientation Exhausted batteries Display shows flashing battery symbol Improper battery compartment insertion Batteries need replacing Display shows flame symbol but The heating is not required at this heating does not switch on moment Display works
8. isplay will show the programmed temperature with the two small arrows How do I set one temperature for the whole day To operate as a simple thermostat with one temperature throughout the day move the slider to the MANual position Adjust the manual temperature by pressing the TEMPerature or w button The manual temperature can be set anywhere from 5 C to 30 C in 0 5 C steps I am having some friends round for coffee How can extend my heating program for a few hours When the slider is in the AUTOmatic position the temperature can be adjusted temporarily by pressing the gs PARTY button Set the party time 1 23 hours by pressing the or button Set the party temperature 5 C 30 C by pressing the TEMPerature a or w button The Chronotherm will control to the new temperature for the set number of hours and then go back to the normal temperature program To cancel the PARTY setting press the button a second time or move the slider The amp button can also be used when you go out shopping out with friends for coffee or to another party and want to reduce the tempera ture for a few hours to save energy have a day off work tomorrow and I am staying at home do I have to re program the CM67NG No with one button press the CM67NG will remember that tomor row is a day off Tomorrow the CM67NG will control the temperature using Sunday s program When the slider is in the AUTOmatic po
9. l change the time quickly The change time can be set in 10 minute steps from 03 00 in the morning The change time can be adjusted to any time up to 02 50 on the next morning so you can maintain the evening temperature after midnight Note If you are pressing the button and the display flashes the next change time number 2 it means the next change time 2 will be pushed forward if you continue to press the button 3 Press the TEMPerature or w button to adjust the first temperature level Holding the button down will change the temperature quickly The temperature can be set in 0 5 C steps from 5 C to 30 C 4 Press the PROGram 2 button to display the second temperature change time and temperature level for Monday Set these by pressing the or button and TEMPerature or w button 5 The remaining temperature changes for Monday can be displayed by pressing PROGram buttons 3 4 5 and 6 and adjusted by using the or button and TEMPerature or w button If you don t want to use all the temperature change times 2 3 4 5 or 6 refer to the next question What if don t want to use all 6 temperature change times You now have a choice to set the program for the next day 6a Press the COPY DAY button to copy Monday s program into Tuesday To set several days of the week to the same program press the COPY DAY button repeatedly 6b Press the DAY 1 7 button to step the day marker to Tue
10. n one minute to change them you may need to correct the time by moving the slider to the DAY position and pressing the button want to use the table stand instead of wall mounted bracket Where can I position the room unit It is important to keep the room unit in a location where reliable RF communication was proven Advise your installer where would you like to position the room unit and he will check if the RF communication is reliable in the selected location s How do I remove the RF Chronotherm from the table stand or wall bracket After programming is finished always replace the RF Chronotherm back on the wall holder or table stand HC60NG Relay Box Controls Layout Push button and relay status LED s What does it mean when the HC60NG relay box green LED is ON Green LED indicates normal operation of the radio frequency system When the green LED is ON the boiler is also ON When the LED is OFF the boiler is OFF
11. re UP button to increase the set temperature a few degrees above the current temperature The heating should come on after a few seconds Switch the boiler on Call electrical installer to check the boiler and relay box power supply as well as the connection between the boiler and the relay box Hook the room unit back on the wall bracket or replace the room unit on the table stand to the position where RF communication was reliable Call installer NOTE You can control the boiler manually when the RF communica tion is lost Press the HC60NG push button to switch the boiler on and off When the green LED is on the boiler is on Call installer Call installer Remove the battery compartment and re insert it If the spanner symbol does not clear itself in a few minutes call the installer Is the Honeywell zoning system easy to use It is very easy to use In fact it is just an additional room unit exactly the same as standard FCM60NG As the system is using RF commu nication you do not have to install the room unit on the wall in the second zone Just mount it on the table stand and find suitable location where the communication is always reliable What are the benefits of installing Honeywell multi zone system Enhanced comfort you can now control temperature individually in each zone Improved efficiency of your heating system your multi zone RF system will save energy delivering heat only to the zones which
12. sday Day 2 The program for Tuesday can then be set as described in steps 2 to 5 Programs for Wednesday Day 3 to Sunday Day 7 can be set in the same way using the DAY 1 7 button 7 Move the slider to the AUTOmatic position when you have completed steps 6a or 6b The Chronotherm will now control the room temperature to match your program What if don t want to use all 6 temperature change times The built in program uses 6 temperature change times as indicated by the numbers 1 2 3 4 5 and 6 on the display With the slider in the PROGram position unwanted change times can be deleted by holding the appropriate PROGram buttons 2 3 4 5 or 6 down for a few seconds The change time will be removed and the display will show dashes instead of a time temperature display Deleted temperature change times can be brought back again by pressing the appropriate program button 2 3 4 5 or 6 for a few seconds with the slider in the PROGram position Can I change the programmed temperature for a short time When the slider is in the AUTOmatic position the temperature can be adjusted temporarily by pressing the TEMPerature or w button This temperature will return to the programmed value at the next temperature change time How do I check the programmed temperature In normal operation the temperature displayed is the actual room temperature To check the programmed temperature press the INFOrmation ii button and the d
13. sition press the lt DAY OFF button A lt symbol will appear and the day marker for tomorrow will flash This indicates that the Sunday temperature program will be followed tomorrow Tomorrow the amp symbol will still appear but without the flashing day marker the CM67NG will control tomorrow s temperatures using Sunday s program To cancel tomorrow s DAY OFF press the g button twice or move the slider If you have 2 or more days off press the button each night before going to bed DAY PROG a _ AUTO MAN OFF Display Tomorrow If you have a DAY OFF today and want to control the temperature using Sunday s program press the button twice To cancel any DAY OFF setting either press the lt f button repeatedly until the lt f symbol disappears or move the slider lam going on holiday for a few days How do save energy but ensure that the house is warm when I return 1 Move the slider to the operating position you require on returning from holiday AUTOmatic or MANual position 2 Press the I HOLIDAY button to display the holiday days counter and temperature 3 Press the or button to set the holiday time 1 99 days An extra flashing day marker shows you the holiday return day 4 Press the TEMPerature or w button to set the holiday temperature 5 C 30 C The unit will control to the new temperature for the set number of days holiday At midnight the
Download Pdf Manuals
Related Search