0.07.B.0020 I5 user guide insert-6Jul2012-NG
Contents
1. here could compromise the service life operation of the product and or be a source of danger 7 Anything not expressly specified in these instructions is not permitted P3 fcons used in this guide ee ee This icon denotes variations and other aspects that should be considered during installation T This icon indicates warning caution or attention Please take special note of critical aspects that MUST be adhered to in order to prevent injury P4 Operation The i5 infrared beam consists of a transmitter and receiver unit mounted on opposite sides of an entrance The transmitter sends a modulated infrared beam to the receiver module When the beam is interrupted the receiver changes the state of an internal relay The contacts of the relay are potential free and can be wired as normally open or normally closed 5 Technical specifications X eee 12V 24V DC AC Transmitter 21mA Receiver 43mA 12V Maximum distance 40m Automatic 9m 10m 5A 220V AC non inductive 15 Cto5o7G 0 90 non condensing Power supply Power consumption Alignment Output contact rating Operating temperature Operating humidity Degree of protection 1P54 6 I nstallation 1 The first step when installing the i5 infrared beams is to obtain maximum alignment The transmitter and receiver are typically mounted directly opposite one another but some leeway is given in the form of a w2. hown in the wiring diagram AABIFY GU VuANI S TA 98d Receiver 12 Terminate wires on INPUT VOLTAGE 12V 30V AC OR DC to the receiver PCBs prior to clipping back into enclosure as shown in the wiring diagram VEALLLIWSNVUL GFY VEINI PTA S8d gt 13 Replace the cover and screw back the fastener and the screw hole cover Indicators e Both the receiver and transmitter are fitted with a green LED indicator e The LED in the transmitter illuminates when the power supply is ON and the receiver LED illuminates when the beams are aligned e A separate wire should be used to obtain COMMON as this ensures the beams are tested accurately by the Beam Test function inherent in many of the later CENTSYS gate operator controllers
3. i5 Infrared beams Pocket installation guide CENTSYS SAFETY DEVICES FOR AUTOMATED GATES CENTSYS S J Q 0 07 B 0020 I5 user guide m inm insert 6J ul2012 www centsys com au PT Introduction per The i5 infrared beams are designed to provide optimum safety by detecting the presence of a person or vehicle traversing the path of a moving gate or door The beams can be interfaced with most automation equipment They can also be used to enhance the security of the automation by enabling the Intruder Detection Alarm function inherent in many of the later CENTSYS gate operator controllers as well as external alarms and buzzers by means of either a normally open or normally closed potential free contact 2 Safety Instructions a te 1 All installation repair and service work to this product must be done by a Suitably qualified person 2 Do not in any way modify the components of the system 3 Do not leave packing materials plastic polystyrene etc within reach of children as such materials are potential sources of danger 4 Dispose of all waste products like packaging materials according to local regulations 5 CENTSYS does not accept any liability caused by improper use of the product or for use other than that for which the automated system was intended 6 This product was designed and built strictly for the use indicated in this documentation Any other use not expressly indicated
4. ide beam being cast should absolute alignment not be possible Position Rx and Tx to be in line and level with each other height of the beam must be tailored to suit the specific requirements of the installation rt CENTSYS recommends the height of 750mm but the Remove cover and prepare for mounting Screw hole ONT a 2 Unclip screw hole cover piece 3 Unscrew cover retaining fastener 4 Lift off cover Unclip PCB and remove 6 Place self adhesive pads onto back of enclosure Self adhesive pads Enclosure or Ring Mounting 7 Mark position of unit 8 Use 5mm masonry bit to drill hole in wall Rawl plug Fastener Height typically 750mm above the ground 9 Mount using fastener provided Wiring Route Option 1 External wire 10a Route the cables through the cable cut out as shown in the illustration providing 12 24 V DC AC to both the receiver and transmitter Cable saddle for cable Option 2 Reticulated wire 10b The cable can also be routed through the hole in the moulding of the back of the enclosure Cable conduit PCB connections It is very important to align the transmitter and the receiver beams Under certain conditions distance gt 10m it may be necessary to fit the cover to achieve alignment NT72C S10 Relay Transmitter 11 Terminate wires on to the transmitter PCBs prior to Suz clipping back into enclosure as s
Download Pdf Manuals
Related Search