Operating Instructions K 3.800 eco!ogic
Contents
1. frost if there is any water residues in them To avoid damage to them gt Completely drain all water from the ap pliance Switch the appliance on with detached high pressure hose and de tached water supply max 1 minute and wait until no more water exits at the high pressure connection Turn off the appliance gt Store the appliance and the entire ac cessories in a frost free room Maintenance and care A Danger Turn off the appliance and remove the mains plug prior to any care and mainte nance work Care Prior to longer periods of storage e g in the winter gt Remove filter from suction hose for de tergent and clean under running water gt Pull out the sieve in the water connec tion using flat nose pliers and clean un der running water Maintenance The appliance is maintenance free Spare parts Use only original KARCHER spare parts You will find a list of spare parts at the end of these operating instructions Troubleshooting You can rectify minor faults yourself with the help of the following overview If in doubt please consult the authorized customer service A Danger Tum off the appliance and remove the mains plug prior to any care and mainte nance work Repair works may only be performed by the authorized customer service Appliance is not running gt Pull on the lever of the trigger gun the device will switch on gt Check whether the voltage indicated on the2. gt Check the detergent suction hose for kinks Customer Service Australia KARCHER Pty Ltd 40 Koornang Road Scoresby Victoria 3179 1800 675 714 Free Call www karcher com au 10 English Technical specifications Electrical connection Voltage 240V 1 50 Hz Connected load 1 7 KW Protection class IP X5 Protective class I Mains fuse slow blow 10A Water connection Max feed pressure 0 8 MPa Max feed temperature 40 C Min feed volume 10 I min Max Suction height 0 5m Performance data Working pressure 11 MPa Max permissible pressure 12 MPa 1800 psi Water flow rate 6 3 l min Detergent flow rate 0 3 I min Recoil force of trigger gun 15N Dimensions and weights Length 285 mm Width 309 mm Height 867 mm Weight 11 3 kg Values determined as per EN 60335 2 79 Hand arm vibration value lt 2 5 m s Uncertainty K 0 3 m s Sound pressure level Lpa 77 dB A Uncertainty Kpa 3 dB A Sound power level Lwa Un 93 dB A certainty Kwa Subject to technical modifications Spare Parts 2 642 172 0 6 392 321 0 363 410 0 4 760 534 0 X English 11 KARCHER www karcher com au
3. mA m This appliance was designed to be used with detergents which are sup plied or recommended by the manufac turer The use of other detergents or chemicals may compromise the safety of the appliance 4 English Safety Devices Caution Safety devices protect the user and must not be modified or bypassed Power switch The appliance switch prevents unintention al operation of the appliance Lock trigger gun This lock locks the lever of the trigger gun and prevents the inadvertent start of the ap pliance Overflow valve with pressure switch The overflow valve prevents the permissi ble working pressure from being exceeded If the lever on the trigger gun is released the pressure switch turns off the pump the high pressure jet is stopped If the lever is pulled the pump is turned on again Prerequisites for the appliance s stability Caution Create stability for the appliance prior to all work on or with the appliance to prevent ac cidents or damage The stability of the appliance is warrant ed when it is placed onto an even sur face Description of the Appliance Coupling element for water connection Suction hose Slide out preventer High pressure hose Quick coupling for high pressure hose Water connection with integrated sieve Appliance switch 0 OFF 1 ON eco Transport handle detachable Accessory net 10 Storage for accessories 11 Mains cable with mains plug OONDQUIDSWN 12 Dete
4. transport damage please contact your dealer Safety instructions A n Danger Never touch the mains plug and the socket with wet hands The appliance must not be used if the power cord or important parts of the ap pliance e g high pressure hoses trig ger gun or safety devices are damaged Check the power cord and mains plug for damage before every use If the power cord is damaged please arrange for it to be replaced immediately by an authorised repair agent or a skilled electrician Check the high pressure hose for dam age before every use Please arrange for the immediate replacement of a damaged high pressure hose The appliance may not be used in areas where a risk of explosion is present If the appliance is used in hazardous ar eas e g filling stations all of the safety provisions and operating instructions detailed in this manual must be ob served High pressure jets can be dangerous if improperly used The jet must not be di rected at persons animals live electri cal equipment or at the appliance itself The high pressure jet must not be di rected at other persons or directed by the user at him herself to clean clothing or footwear Never use the appliance to clean ob jects containing hazardous substances e g asbestos Vehicle tyres or tyre valves are suscep tible to damage from the high pressure jet and may burst The first indication of this is a discolouration of the tyre Dam aged veh
5. type plate corresponds to the volt age of the mains supply gt Check the mains connection cable for damages Pressure does not build up in the appliance gt Check setting at the spray lance gt Appliance ventilation Switch the appli ance on with the high pressure hose detached and operate max 2 minutes until the water exits the high pressure connection without bubbles Switch off appliance and reconnect high pressure hose Check the water supply Pull out the sieve in the water connec tion using flat nose pliers and clean un der running water gt Suction height of 0 5 m when vacuum ing from open container has been ex ceeded Appliance does not start motor hums Cause Voltage reduction due to weak mains supply or when using an extension cable gt When switching on first pull the lever of the hand spray gun and then switch the appliance switch to I ON or eco yy English 9 Strong pressure fluctuations gt Clean high pressure nozzle Remove dirt and debris from the nozzle bore us ing a needle and rinse through with wa ter from the front gt Check water flow quantity Appliance is leaking gt Slightleakage from the appliance pump is normal If the leakage increases con tact the authorized customer service No detergent infeed gt Use spray lance with pressure regula tion Vario Power Turn the spray lance to Mix position gt Clean the detergent suction hose filter
6. K 3 800 ecologic KARCHER lee Operating Instructions Before first use of the unit read these operating instructions and act in accordance with them ZN LL 59662500 04 14 General information 2 Safety instructions 3 Description of the Appliance 5 Operation eee 6 TANSPOM cucee dace gaia rini 8 Storage 8 Maintenance and care 9 Troubleshooting 9 Customer Service 10 Technical specifications 10 Spare Parts 11 General information Dear Customer A Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent own ers Proper Use This high pressure cleaner is designed for domestic use only to clean machines vehicles buildings tools facades terraces garden equip ment etc using a high pressure water jet and detergents if required with accessories replacement parts and detergents approved by KARCH ER Observe the instructions provided with these detergents Symbols in the operating instructions A Danger Immediate danger that can cause severe injury or even death A Warning Possible hazardous situation that could lead to severe injury or even death Caution Possible hazardous situation that could lead to mild injury to persons or damage to prop
7. ay leak from the connections after operation gt Lock the lever on the trigger gun gt Pull out the mains plug 8 English Caution In order to prevent accidents or injuries keep in mind the weight of the appliance during transport see Specifications When transporting by hand Illustration I gt To push the appliance the transport handle must be pulled all the way up it will lock into place audibly gt Pull the appliance by its transport han dle gt Lift appliance by the carrying handle and carry it When transporting in vehicles gt Secure the appliance against shifting and tipping over Caution In order to prevent accidents or injuries keep in mind the weight of the appliance when selecting a storage location for it see Specifications Storing the Appliance gt Park the machine on an even surface gt Press the disconnect on the trigger gun and remove the high pressure hose from the trigger gun gt Push the casing of the quick coupling for the high pressure hose toward the rear and disconnect the high pressure hose from the appliance gt Stow away the mains cable the high pressure hose and accessory on the appliance Prior to extended storage periods as dur ing the winter also observe the instructions in the Care section Frost protection Caution Protect the appliance and its accessories against frost The appliance and its accessories can get destroyed through
8. erty 2 English Symbols on the machine The high pressure jet may not be directed at persons ani mals live electrical equipment or at the appliance itself Pro tect the appliance against frost Environmental protection Oy The packaging material can be recy cled Please do not place the packag ing into the ordinary refuse for disposal but arrange for the proper recycling Old appliances contain valuable ma terials that can be recycled Please m arrange for the proper recycling of old appliances Please dispose your old appliances using appropriate collec tion systems D The extraction of water from public waters is prohibited in some coun tries D Work with detergents must only be performed on liquid tight work surfac es with connections to the wastewa ter runoff Do not let release detergent into waters or earth D Cleaning operations which produce oily waste water e g engine washes underbody washes may only be car ried out using washing stations equipped with an oil separator D Lower water and energy use thanks to the eco setting see chapter Op eration Notes about the ingredients REACH You will find current information about the ingredients at www kaercher com REACH Scope of delivery The scope of delivery of your appliance is il lustrated on the packaging Check the con tents of the appliance for completeness when unpacking In the event of missing accessories or any
9. ffocation The operator must use the appliance correctly When working with the appli ance he must consider the local condi tions and pay due care and attention to other persons in particular children who are nearby Do not use the appliance when there are other persons around unless they are also wearing safety equipment English 3 M Wear protective clothing and safety goggles to protect against splash back containing water or dirt Caution E ncaseofextended downtimes switch the appliance off at the main switch ap pliance switch or remove the mains plug m Donotoperate the appliance at temper atures below 0 C m Observe a distance of at least 30 cm when using the jet to clean painted sur faces to avoid damaging paintwork m Never leave the appliance unattended when it is in operation m Make sure that the power cable or ex tension cables are not damaged by run ning over pinching dragging or similar Protect the power cable from heat oil and sharp edges m All current conducting parts in the work ing area must be protected against jet water m The appliance may only be connected to an electrical supply which has been installed in accordance with IEC 60364 E The appliance may only be connected to alternating current The voltage must correspond with the type plate on the appliance m Forsafetyreasons we recommend that you operate the appliance only via an earth leakage circuit breaker max 30
10. icle tyres tyre valves are high ly dangerous Ensure that a distance of at least 30 cm is observed when clean ing with the jet Risk of explosion Do not spray flammable liquids Never draw in fluids containing solvents or undiluted acids This includes petrol gt paint thinner and heating oil The spray mist thus generated is highly inflamma ble explosive and poisonous Do not use acetone undiluted acids or sol vents as they are damaging to the ma terials from which the appliance is made Warning The mains plug and the coupling of an extension cable must be watertight and must never lay in the water Unsuitable electrical extension cables can be hazardous Only use electrical extension cables outdoors which have been approved and labelled for this pur pose and have an adequate cable cross section 1 10 m 1 5 mm 10 30 m 2 5 mm Always fully unroll electrical cables from the cable drum High pressure hoses fixtures and cou plings are important for the safety of the appliance Only use high pressure hos es fixtures and couplings recommend ed by the manufacturer This appliance is not intended for use by persons with reduced physical sen sory or mental capabilities The appliance must not be operated by children or persons who have not been instructed accordingly Children should be supervised to pre vent them from playing with the appli ance Keep packaging film away from children risk of su
11. ion hose in a container filled with detergent English 7 gt Use spray lance with pressure regula tion Vario Power gt Turn the spray lance to Mix position Note This will mix the detergent with the water stream Note If required the washing brushes can be used to work with detergent Recommended cleaning method gt Spray the detergent sparingly on the dry surface and allow it to react but not to dry gt The Dirtblaster reaches its maximum cleaning performance in standard mode Interrupting operation Release the lever on the trigger gun Lock the lever on the trigger gun During longer breaks more than 5 min utes also turn the appliance off using the 0 OFF switch gt Insert the trigger gun in its holder VI Finish operation Caution Only separate the high pressure hose from the trigger gun or the appliance while there is no pressure in the system gt After working with detergent suspend detergent suction hose in a container filled with clear water switch the appli ance on for around 1 minute once the spray lance has been removed and rinse until water runs clear gt Release the lever on the trigger gun gt Turn off the appliance 0 OFF gt Turn off tap gt Press the lever on the trigger gun to re lease any remaining pressure in the system gt Detach the appliance from the water supply Caution When disconnecting the supply or high pressure hose hot water m
12. rgent suction hose with filter 13 Wheels 14 Trigger gun 15 Lock trigger gun 16 Key to detach the high pressure hose from the trigger gun 17 Spray lance with Dirtblaster 18 Spray lance with pressure regulation Vario Power Optional 19 Water filter order no 4 730 059 English 5 Operation Switch position eco There are the switch positions 1 ON and eco to switch the appliance on Note The switch position eco allows the control of pressure and leads to water and energy savings of approx 20 by using the spray lance Recommended application ranges for switch position eco eo T W S 5 wll Before Startup Mount loose parts delivered with appliance prior to start up Illustrations on Page 5 Install wheels gt Illustration IN Secure the wheels using the included plug Align the plug properly Install the transport handle gt Illustration E Place the transport handle into the in take until you feel resistance Use the heel of your hand or a soft rubber mallet to position it Attach the accessories net gt Illustration Hook the accessories net into the hooks shown in the illustration 6 English Connect the high pressure hose to the trigger gun gt Illustration DI Push the high pressure hose into the trigger gun until it locks audibly Note Make sure the connection nipple is aligned correctly Check the sec
13. spray lance firmly gt Pull on the lever of the trigger gun the device will switch on Note Release the lever of the trigger gun the device will switch off again High pres sure remains in the system Spray lance with pressure regulation Carrying out the most common cleaning tasks The work pressure can be infinitely regulated between Min and Max gt Release the lever on the trigger gun gt Turn the spray lance to the desired po sition Suitable for working in switch position eco Note Suitable for working with detergent for this turn the spray lance to the Mix po sition Spray lance with Dirtblaster For particularly dirty items or areas Caution Car tyres paint or sensitive surfaces such as wood should not be cleaned with the dirt blaster as there is a risk of damage Not suitable for use with detergents Not suitable for working in switch posi tion eco Working with detergent Please use exclusively KARCHER deter gents and care products to carry out the re spective cleaning task as these were specifically developed for your appliance The use of other detergents and care prod ucts may lead to premature wear and can invalidate your warranty claims Please ob tain information at your local dealer or re quest information directly from KARCHER gt Illustration E Pull detergent suction hose as far as is required out of the housing Suspend end of detergent suct
14. ssure pump and accessories For protection the use of the KARCHER water filter optional accessory order no 4 730 059 is recommended gt Fill the suction hose with water gt Figure Screw the suction hose into the water connection of the appliance and insert it into the water source e g rainwater drum Start up Caution Dry runs lasting longer than two minutes lead to damages to the high pressure pump If the appliance does not build up pressure within two minutes switch it off and proceed as instructed in the Chapter Troubleshooting Insert the mains plug into the socket Set the appliance switch to 1 ON Unlock the lever on the trigger gun Pull on the lever of the trigger gun the device will switch on Switch the appliance on for a max of 2 minutes and wait until the water exits at the hand spray gun without bubbles Release the lever on the trigger gun Set the appliance switch to 0 OFF VIVI yy Operation Caution Prior to cleaning make sure that the high pressure is placed safely on level ground Wear protective goggles and protective clothing during the cleaning process gt Illustration A Push the spray lance into the trigger gun and fasten it by turning it through 90 gt Set the appliance switch to 1 ON A Danger The trigger gun is subjected to a recoil force when the water jet is discharged Make sure that you have a firm footing and are also holding the trigger gun and
15. ure connection by pulling on the high pressure hose Connect high pressure hose to the appliance gt Illustration B Insert the high pressure hose tightly into the quick coupling on the appliance it will lock in audibly Note Make sure the connection nipple is aligned correctly Check the secure connection by pulling on the high pressure hose Water supply A Warning According to the applicable regula tions the appliance must never be used on the drinking water supply without a system separator Use a suitable system separator manufactured by KARCHER or as an alternative a system separator as per EN 12729 Type BA Water flowing through a system separator is con sidered non drinkable Caution Always connect the system separator to the water supply never directly to the appli ance Water supply from mains Observe regulations of water supplier For connection values see type plate tech nical data gt Use a fibre reinforced water hose not included with a standard coupling Minimum diameter 1 2 inch 13 mm minimum length 7 5 m gt Figure Gl 1 Screw the coupling element to the wa ter connection on the appliance 2 Push the water supply hose onto the coupling unit gt Connect the water supply hose to the water supply gt Completely open the water tap Drawing in water from open reservoirs Note The max suction height is 0 5 m Note Impurities in the water can damage the high pre
Download Pdf Manuals
Related Search