Electrician Installation Manual National Warranty Line
Contents
1. ERNATION AL k Checklist Electricians make sure everything on this checklist is ticked off before you leave the installation site If you have trouble installing our product please refer to the trouble shooting section on the previous page first then phone the Hunter Pacific Warranty Line on 1300 360 280 open 9am to 5pm EST DO NOT uninstall the fan and DO NOT return fan to retailer 10 WARNING Ceiling fan is not installed to a solid state wall controller Neither leading nor lagging edge controllers will give satisfactory performance Wall controllers must only be types approved for use by Hunter Pacific International The fan optional fan light and bracket is earthed Fan and optional fan light are run from the same final circuit Mounting bracket must be firmly secured to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for certain types of installation Fan blades are at least 2 1m feet above floor level If fan is installed on a wall controller or pull cord check the fan is operating correctly on all three speeds If light is installed Check light switch is functioning properly f remote control is installed Check the fan and light if installed is responding to the remote control correctly If remote control is installe2. If you have any difficulties installing our product we recommend you to call our warranty line on 1300 360 280 for advice 132cm 52 Majestic Madagascar Burnt Copper 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC INTERNATIONAL Electrician Installation Manual Majestic Madagascar Ceiling Fan Installation Instructions Assembling the fan STEP 1 Fig 1 ONLY PERFORM THIS STEP IF FAN WIRES HAVE NOT BEEN FED THROUGH DOWN ROD a Loosen the ball joint screw and remove the ball joint pin to separate the down rod from the ball joint b Feed wires from motor housing up and through the down rod c Insert the cotter pin through the connection collar and the down rod avoid pinching wires Then lock the down rod using the cotter key and washer Secure down rod with the two down rod screws provided d Slide on canopy cover and refit the ball joint e If extensions rods need to be installed please go to page 8 STEP 3 Fig 3 Hanger Timber Nogging Bracket Hex Head Screw STEP 2 Fig 2 a Drill a hole in the ti
3. or Winter position Fan is not corresponding to the remote control Check for flat battery Make sure the dipswitch settings in the hand piece and the remote receiver for the same fan are corresponding Fan is wobbling Check the ball joint slot is locked into the hanger bracket groove Make sure blades are a matching set the letters on matching sets of blades should be identical with the numbers varying within 3 grams of each other Check blade screws are tightened firmly If necessary use balancing kit provided to settle the wobble Fan is noisy Check all screws and parts are secured firmly Ensure there are no loose parts moving inside the motor housing Make sure fan is installed with a Hunter Pacific wall controller only do not use solid state controllers as they can cause unpleasant motor noises National Warranty Line 1300 360 280 WARNING Monday to Friday from 9am to 5pm EST Only available within Australia Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 11 HUNTER PACIFIC IN T Quic Electrician Installation Manual Majestic Madagascar Ceiling Fan
4. Electrician Installation Manual Majestic Madagascar Ceiling Fan HUNTER PACIFIC INTERNATIONAL ols a o r m 7 os a a a n CEILING FAN MUST BE INSTALLED BY A LICENSED ELECTRICIAN NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN After installation electricians must tick off all items on the quick checklist and fill out their details onto the back page of the Fan Owner Warranty amp Operations Manual ELECTRICIANS TO PROTECT YOUR CUSTOMER S WARRANTY PLEASE READ PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Hunter Pacific International Pty Ltd Building 8 256 New Line Road Dural NSW 2158 Australia ABN 18 063 521 666 1 Electrician Installation Manual Majestic Madagascar Ceiling Fan HUNTER PACIFIC N TERNATIONAL IMPORTANT INFORMATION ELECTRICIANS MUST READ PRIOR TO INSTALLATION Distributor and installer_details and purchase receipts are essential for on site warranty claims and must be presented to repair personnel make sure you record your details in the Fan Owner Warranty and Operations Manual Fans and fixed wiring products must only be installed by persons who are appropriately licensed by the applicable State regulatory body Therefore to protect our repair personnel on site warranty claims will not be accepted if products have been installed by u
5. d Check where possible a separate isolation switch has been installed for the fan Check electrician s details have been recorded onto the back page of the Owner s Operations and Warranty Manual 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 12
6. f WARNING the fan If only one blade is damaged you are still required to replace with a new set 10 HUNTER PACIFIC Electrician Installation Manual Majestic Madagascar Ceiling Fan INTERNATIONAL Trouble Shooting Tips Fan Fan will not start Check that the reversing switch is pushed into its Summer or Winter position Check wire connections in the wall switch and terminal blocks ensure all wires are making proper contact If it is a Typhoon fan check and ensure the reversing switch plate under the switch cover is not bent also check the 3 wires coming from the switch plate are straight Occasionally the switch plate may get bent during transportation this allows the switch cover to press against the plate and stop the fan from working If it is a Typhoon fan check the nine pin plug under the switch cover is properly connected and the colours on the plug are corresponding If it is a Concept fan and it has an external start up capacitor check that this external capacitor is properly connected Fan speed is not corresponding to the wall controller Check the speeds on the wall controller has been wired correctly and are making proper contact Brown speed 1 Purple speed 2 Red speed 3 Check wires in the terminal block are connected properly connection wires should be stripped back at the connection point and unused wires should be sealed and capped off Check that the reversing switch is pushed into its Summer
7. h as T hooks are available for certain types of installation e After installation fan blades must be at least 2 1 m 7 feet above floor level f The use of these products by children and the infirm must be under supervision IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY HOT LINE NUMBER 1300 360 280 BEFORE LEAVING THE JOB SITE PLEASE DO NOT REMOVE THE FAN FROM THE CEILING ONCE INSTALLED UNLESS INSTRUCTED TO DO SO Electrician Installation Manual Majestic Madagascar Ceiling Fan HUNTER PACIFIC INTERNATIONAL Parts List Majestic Madagascar Hex Head Screw Blade Screw Blade Washer Motor Housing Pull Cord CC yy Pi Assembly Kit Blade Holder i Washer amp Screw Part Qty Part ty Blades Canopy Cover Screws 0 Canopy Cover a y art L mp lt ex Head Screw Ball Joint 15cm Down Rod Down Rod Cotter Washer Ball Joint Screw Down Rod Cotter Pin Down Rod Screws Ball Joint Pin Down Rod Cotter Key these parts come preassembled Pull cord Assembly Kit Comes preassembled 1x pull cord assembly 1x start up capacitor 1x speed capacitor 1x pull chain 3x screws and 2x lights wires 3 N Electrician Installation Manual Majestic Madagascar Ceiling Fan HUNTER PACIFIC INTERNATIONAL IMPORTANT INFORMATION The table below contains information that can help you quickly identify the product you are installing
8. light kit screws to separate the top cover from the lower part of the light kit b Feed light wires through thread and Sa LKE into the light kit Thread Aes c Attach the light kit to pull cord 4 assembly kit by tightening the thread clockwise as shown in figure 11 d Connect light wires to terminal block in lower part of the light kit of Light Kit e Reattach lower part of the light kit to the top cover of the light kit using the three screws removed from step 2 a Terminal Block Lower Part of Light Kit 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC INTE Electrician Installation Manual Majestic Madagascar Ceiling Fan RNATIONAL Installation Instructions Attaching an accessory light kit Motor Housing _ Nine Pin Plug Connectors Pull Cord STEP 3 Fig 12 Assembly Kit a Connect the two ends of the nine pin plug together Make sure the colours on A Screw the plugs are corresponding b Secure the pull cord assembly kit with the light attached to the motor housing using the 3 screws p
9. mber nogging for wiring b Secure the hanger bracket onto the timber nogging using the two hex head screws provided The timber nogging should be supplied by the installing electrician and must be supported between the two ceiling joists as shown in the diagram above Hanger Bracket a Hang the ball joint into the hanger bracket Ensure the groove on the hanger bracket is locked into the slot on the ball joint This is important to ensure the fan will not wobble and the weight of the fan is supported 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Majestic Madagascar Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan STEP 4 Fig 4 amp 5 a Connect wires from the fan with wires in the ceiling via the terminal block on the hanger bracket refer to figure 4 and 5 b Make sure earth wires are also connected c Connect light wires red white if a light fitting is going to be used Cap seal light wires if a light fitting is not going to be used Wiring Instructions
10. n Instructions Attaching an extension rod Hunter Pacific rods to be used ONLY Motor Housing Cap Ball Joint Connection Collar NN Down Ro all gt F pt Cotter Step 2 Fig 11 Loosen the ball joint screw take out the ball joint pin and remove the ball joint Then slide off the canopy cover Step 1 Fig 10 Loosen the down rod screws and unlock and remove the cotter pin to remove the standard down rod from the motor housing Ball Joint Pin Ball Joint Motor Housing Cap Cotter A kt A _ Connection Collar Tighten Ball Ch kh Joint Screw iis I S _ Cotter Key N Down Ro S l DK Cotter Pin EAN T Step 3 Fig 12 amp 13 Now install the extension rod and reverse step 1 amp 2 to secure the rod to NOTE If the extension rod needs to be shortened cut the rod to the required length and drill the appropriate hole size to fit the ball joint pin The cut end of the rod should be used on the ball joint end only When installing a 1 8m extension rod the wiring will need to be extended and joined This should be done using crimp style connectors 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance o
11. nlicensed persons Damage caused by incorrect installation force majeure electrical surges lightning power grid fluctuations water or by connection to alternative power supply sources such as solar inverters etc is not eligible for warranty repair Blades must be replaced only as a complete set Blades are supplied only as a pre balanced set and the replacement of individual blades may void the warranty by causing mechanical damage to the motor excessive noise or premature wear When products are installed in a location requiring special access equipment such as scaffolding or scissor lifts etc the cost of providing installing and operating _special access equipment must be borne by the site owner For safety and to protect your customers warranty the following must be taken into account when installing and operating the product s a DO NOT USE SOLID STATE WALL CONTROLLERS Neither leading nor lagging edge controllers will give satisfactory performance Wall controls must only be types approved for use by Hunter Pacific International b The fan light and bracket must be earthed c Fan and light must be run from the same phase and preferably the same final circuit d Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts suc
12. rovided c Attach the pull cord handle to the pull cord chain Trouble Shooting Tips Light WARNING Light will not turn on Make sure globe has not blown and it is properly fitted between the metal prongs Check all light wires in the light kit canopy cover terminal block and wall switch has been connected together correctly Light is not corresponding to remote control Make sure globe has not blown and it is properly fitted between the metal prongs Check all light wires in the light kit canopy cover terminal block and wall switch has been connected together correctly Check dip switch settings in remote hand piece and remote receiver are corresponding Light wires appears to be missing or too short Wires may be stuck in the motor housing Carefully pull wires out of the motor housing careful not to strip the wires as this may cause the fan to short Light flickers or flashes Check globe is secured between the metal prongs in the light kit Make sure you are using the globes specified 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of Electrician Installation Manual Majestic Madagascar Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installatio
13. ten the canopy covers screws this will stabilise the canopy cover lt GO SF eS GE P Blade with J Holder attached Motor Housing Blade Holder Screw STEP 7 Fig 8 a Attach blade holders to the motor housing blades should already be attached STEP 8 Fig 9 a Unscrew the pull cord screws to separate the pull cord assembly kit from the motor housing b Make sure the two ends of the nine pin plug are connected together and the colours on the plugs are corresponding c Use pull cord screws to re secure the pull cord assembly kit to the motor housing d Attach the pull cord handle to the pull cord chain 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Majestic Madagascar Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Attaching an accessory light kit NOTE These instructions follow from step 7 of the Assembling the Fan section on page 3 STEP 1 Fig 10 a Use thumb to push out the plug in the pull cord assembly kit see figure 10 STEP 2 Fig 11 a Loosen and remove the
14. with and without accessory light Brown Active Wire Blue Neutral Wire Brown Active Wire E Red White for Light Brown for Fan Green Earth Wire Light Controlled from Wall Controller T and Fan Controlled by Pull Cord Fig 5 Blue Neutral Wire Fan Motor Light Active Brown Light Fitting 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC INTERNATIONAL Electrician Installation Manual Majestic Madagascar Ceiling Fan Installation Instructions Assembling the fan pe Hanger Bracket Y Canopy Cover Canopy Cover Screws Blade Screw Blade Washer STEP 6 Fig 7 a Attach blades on to the blade holders as shown in figure 7 e Pull Cord Screw N Base of Motor Housing Nine Pin Plug Connectors WARNING STEP 5 Fig 6 a Slide canopy cover up and over the hanger bracket b Twist canopy cover as shown in diagram until the screws holes can be seen c Half loosen canopy cover screws d Now twist canopy cover in the opposite direction to the diagram and fully tigh
Download Pdf Manuals
Related Search