COMMUNICATOR MODEL SP323 g OWNER'S MANUAL
Contents
1. COMMUNICATOR MODEL SP323 OWNER S MANUAL AND OPERATING INSTRUCTIONS When the COMMUNICATOR is not being used conserve battery power by pressing the JJ button to OFF Remove the batteries if the unit will not be used for a long period of time Communicator Controls 1 Antenna 2 LCD Screen Displays current channel selection and other radio status symbols 3 Torch X button Press and hold to turn on the torch 4 Up amp button VOLUME CHANNEL Press to adjust volume level and change channels 5 Down button VOLUME CHANNEL Press to adjust volume level and change channels 6 Call button Press to transmit CALL TONES 7 Battery Compartment LOCATED ON THE REAR Houses 3 x AAA alkaline or Ni MH rechargeable batteries not included 8 Speaker 9 Battery Compartment Cover Latch LOCATED ON THE REAR Secures Battery Compartment cover 10 SCANS button Press and heid 1 see for channel scanning Press once to switch on off repeater function 11 Mic Microphone 12 Menu Power On Off Q button Press and hold the button to turn your unit ON OFE Allows you to change channels select high low power Press to tune in and hold onto weak signals 13 PUSH TO TALK PTT button Press to transmit 14 TX Transmission LED indicator Illuminates red when transmitting Lights up once every 15 seconds to show battery low 15 LED Torch 16 Belt Clip LOCATED ON THE REAR Getting Started Carefully remov2. a signal tone and the LCD Screen will turn blank Adjusting Speaker Volume 1 Press the Up A button to increase the Speaker Volume 2 Press the Down button to decrease the Speaker Volume 3 The Speaker Volume level is indicated by the number 1 to 8 displayed on the LCD Screen Receiving a Signal The unit is continuously in the RECEIVE mode when the unit is ON and not Transmitting When you receive a signal on the current channel the RX icon is displayed See LCD SCREEN for details and red LED indicator lights up Transmitting a Signal 1 Check the channel activity by using MONITOR function See below MONITOR section You ll hear static if the channel is unoccupied Don t TRANSMIT if someone is talking on the channel Press and hold the PIT button to TRANSMIT The TX LED Indicator will light up in red Hold the unit in a vertical position with the MICROPHONE 2 to 3 inches from the mouth 2 While holding the PTT button speak into the unit using a normal tone of voice 3 Release the PIT button when you have finished transmitting NOTE In order for other people to receive your transmission they must also be on the same channel you are currently using Refer to the Changing Channels section for more information Operation Changing Channels The COMMUNICATOR has 38 available channels lo change channels Press the J button until the current channel number flashes on the LCD Screen While the channel num
3. ber is flashing e Press the Up button to move to a higher channel e Press the Down button to move to a lower channel e The channel changes from 1 to 40 or from 40 to 1 channel 22 amp 23 being inhibited 3 Press the PTT button to confirm the selected channel and return to the NORMAL mode NOTE Refer to the Channel Table section of this Owner s Manual for detailed frequency listings m N High Low power selection 1 Press twice to enters to High Low power page 2 Press A button to select the power level The LCD panel indicate L when low power is selected Low power can extend the life of battery life but would reduce the talking range Monitor You can use the MONITOR feature to check for weak signals in the current channel 1 Press the 0 0 button 3 times to activate this function 2 Press again the J button to deactivate the function
4. e your communicator from its Packing If there is any visible damage do not attempt to operate this communicator Return it to the place of purchase Removing the BELT CLIP A B De o e Mh Figure 1 i m a Yy Figure 2 1 Pull the BELT CLIP LATCH away from the unit 2 While pulling the BELT CLIP LATCH push up on the BELT CLIP to remove it from the unit See Figure 1 Installing the Belt Clip 1 Slide the BELT CLIP into the BELT CLIP SLOT See Figure 2 2 A click indicates the BELT CLIP is locked into position Battery Installation 1 Release the BATTERY COMPARTMENT COVER LATCH located on the rear side of the unit see Figure 3 and remove the BATTERY COMPARTMENT COVER from the BATTERY COMPARTMENT See Figure 4 2 Install 3x1 5V AAA alkaline batteries or Ni MH rechargeable batteries not included as shown 3 Reinstall the BATTERY COMPARTMENT COVER and lock the BATTERY COMPARTMENT COVER LATCH into position Figure 3 Figure 4 LCD Screen RX Icon Repeater Icon Low Power Icon TX Icon __ Channel Number Volume Level RX Light on in Receiving mode L Light on when low power is selected Turning the Unit ON __ Press and hold the A O button The unit will beep with dual tone and the LCD SCREEN will briefly display a SELF TEST Screen Turning the Unit OFF Press and hold the M O button The unit will beep with
Download Pdf Manuals
Related Search