Digital Inverter Generator G4000X Operating Instructions
Contents
1. G4000X Operating Instructions Please read this manual carefully before use Thank you for purchasing our generator This manual covers operation and maintenance of the G4000X All information in this publication is based on the latest product information available at the time of approval for printing We reserve the right to make changes at any time without notice and without incurring any obligation The copyright of this manual belongs to our company no part of this publication may be reproduced without written permission This manual should be considered a permanent part of the generator and should remain with it if it is resold Pay special attention to statements preceded by the following words WARNING It indicates a strong possibility of severe personal injury or death if instructions are not followed CAUTION It indicates a strong possibility of severe personal injury or death if instructions are not followed lf a problem should arise or if you have any questions about the generator consult an authorized dealer BE CAREFUL The generators are designed to give safe and dependable service if operated according to instructions Read and understand the Owner s Manual before operating the generator Failure to do so could result in personal injury or equipment damage AL WARNING The generator is designed to give safe and dependable service if operated according to instructions Read and understand this manual care2. circuit breaker 8 AC socket 16 Grounding terminal Muffler cover cover CONTROL PANEL DC circuit breaker Overload indicator light Eco throttle switch Output indicator light Oil alert indicator light Grounding terminal AC socket DC socket Engine switch SMART THROTTLE Engine speed is kept at idle automatically when the electrical appliance is disconnected and it returns to the required speed to power the electrical load when the electrical appliance is connected This position is recommended to minimize the fuel consumption while in operation ANRT INSTRUCTIONS The generator is designed to give safe and dependable service if operated according to instructions e Read and understand the Owner s Manual before operating the generator Failure to do so could result in personal injury or equipment damage e Exhaust gas contains poisonous carton monoxide Never run the generator in an enclosed area Be sure to provide adequate ventilation The muffler becomes very hot during operation and remains hot for a while after stopping the engine Be careful not to touch the muffler white it is hot Let the engine cool before storing the generator indoors The engine exhaust system will be heated during operation and remain hot immediately after stopping the engine To prevent scalding pay attention to the warning marks e Gasoline is extremely flammable and explosive under certain conditions Refuel in a well ventil
3. claim by a third party or any special indirect or consequential loss or damage of any nature whatsoever caused by Bush Power s failure in complying with its obligations BUSH POWER IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS INTENDED FOR THE BUSH POWER PRODUCT In the following paragraph Our means Bush Power and You means the customer Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure The benefits given to the customer in this warranty are in addition to other rights and remedies under a law in relation to the products to which this warranty applies WARRANTY CARD To be detatched and returned with the unit to the below address Name Company Name Address Ph o Fax E mail Purchased From Date Purchased Product Purchased Model No This product is supplied with a 5 Year Warranty from date of purchase Please Note Should you experience any warranty related issues with this charger please call Matson Warranty Department on 02 9833 3444 between the hours of 8am 4 00pm Monday Friday Our Warranty De
4. large starting power the overload indicator lights red and the output indicator light green may light together for a short time but this is no abnormality After starting the equipment the overload indicator light red will go out after a few seconds and the output indicator light green will stay lit Connected Load Suggested DC Battery Generator Size 2000W Incandescent lamps 2000W Rated 2000W Power Tools Fluorescents 2500W voltage 12v 1000W Fridge Compressors 4000W Note This table is a guide only In some instances such as large air conditioners etc a generator up to six times the load may be required DC Applications For charging 12V automotive batteries en Sa a voltage V voltage V current A Opening the smart throttle 22 11216 DC Max output power The generator cannot sense a variable load with the same power which the manual indicates It only can sense 40 70 power which the manual indicates Example Generator rated output 3 7KVA Power factor AG 1 0 0 3 7KVA O08 4 6KVA DC DE gt 12V 8 3A When using the DC output turn Smart Throttle to the OFF position The DC current will be below 5A if turning on the Smart Throttle without AC current output When charging batteries person must be present to monitor the voltage Stop charging when the voltage of the batteries is above 16V Or it may cause battery explosion resulting in serious injury or death To prevent the
5. possibility of creating a spark near the battery connect charging cable first to the generator then to the battery Disconnect cable first at the battery Before connecting charging cables to a battery that is installed in a vehicle disconnect the vehicles grounded battery cable Reconnect the vehicle s grounded battery cable after the charging cables are removed This procedure will prevent the possibility of short circuit and sparks if you make accidental contact between a battery terminal and the vehicle s frame or body Do not attempt to start an automobile engine while the generator is still connected to the battery the generator may be damaged Connect the positive battery terminal to the positive charging cord Do not reverse the polarity of the charging cables or serious damage to the generator and or the battery may occur The battery can give off explosive gases keep spark flames and cigarettes away Provide adequate ventilation when charging The battery contains sulphuric acid electrolyte Contact with skin or eyes may cause severe burns Wear protective clothing and a face shield If electrolyte gets on your skin flush with water If electrolyte gets in your eyes flush with water for at least 15 minutes and call a physician Electrolyte is poisonous If swallowed drink large quantities of water or milk and follow with milk or magnesia or vegetable oil and call a physician KEEP OUT OF THE REACH OF CHILDREN PET
6. rain or snow and do not let it get wet SAFETY LABEL LOCATIONS These labels warn you of potential hazards that can cause serious injury Read the labels safety notes and precautions described in the manual carefully If a label comes off or becomes hard to read contact your dealer for a replacement PRE OPERATION CHECK Be sure to check the generator on a level surface with the engine stopped and the brakes are tightened Make sure no other equipment objects buildings or hazards are within 1 metre of the generator Apply the brakes on the wheels before starting the generator Check the engine oil level Using non detergent oil or 2 stroke engine oil could shorten the engine s service life Use high detergent premium quality 4 stroke engine oil certified to meet or exceed U S automobile manufacturer s requirements for API Service Classification SG SF 15W40 Select the appropriate viscosity for the average temperature in your area SAE VISCOSITY GRADES Single viscosity Multi viscosity 0 20 40 60 80 100F Ambient Temperature Loosen the cover screw and remove the left side maintenance cover Remove the oil filler cap and wipe the dipstick with a clean rag Check the oil level by inserting the dipstick in the filler hole without screwing it in If the oil level is below the end of the dipstick refill the recommended oil up to the top of the oil filler neck The Oil Alert System will automatically
7. stop the engine before the oil level falls below the safe limit However to avoid the inconvenience of an unexpected shutdown it is still advisable to visually inspect the oil level regularly Dipstick Pit W I a M Upper oil level allowed at i w Oil filler hole Lowest oil Level allowed Check the fuel level Turn the fuel cap lever to OFF position before transporting Use automotive fuel Unleaded or low leaded is preferred to minimize combustion chamber deposits I Don t use fuel containing ethanol or alcohol Fuel system damage or engine performance problems resulting from the use of fuels that contain ethanol or alcohol are not covered under the warranty Never use an oil gasoline mixture or dirty gasoline Avoid getting dirt dust or water in the fuel tank After refuelling tighten the fuel filler cap securely Fuel level display Gasoline is extremely flammable and is explosive under certain conditions Refuel in a well ventilated area with the engine stopped Do not smoke or allow flames or sparks in the area where the engine is refuelled or where gasoline is stored Do not overfill the fuel tank After refuelling make sure the tank cap is closed properly and securely Be careful not to spill fuel when refuelling Spilled fuel or fuel vapour may ignite If any fuel is spilled make sure the area is dry before starting the engine Avoid repeated or prolonged contact with sk
8. the faulty item to the address supplied above Exclusions from Warranty This warranty does not apply to products where there is evidence of Improper maintenance or abuse to the products the products have been exposed to harsh environmental conditions or those outside the specified operating conditions Unauthorised modification is evident to the products or misuse of products Operation outside the products specification Warranty Disclaimers Bush Power s liability in respect of a breach of a consumer guarantee or any warranty made under these warranty terms and conditions for any products not of a kind ordinarily acquired for personal domestic or household use is limited in relation to the products to the extent permissible by law and at it s option to replacing the products or the supply of equivalent goods the repair of the products the payment of the cost of replacing the products or of acquiring equivalent goods or the payment of the cost of having the products repaired To the extent permitted by law all other warranties whether implied or otherwise not set out in these warranty terms and conditions are excluded and we are not liable in contract tort including without limitation negligence or breach of statutory duty or otherwise to compensate the customer for any increased costs or expenses any loss of profit revenue business contracts or anticipated savings any loss or expense resulting from a
9. the utility lines Such backfeed may electrocute utility company workers or others who contact lines during a power outage and the generator may explode or cause fires when utility power is restored ATINS To avoid accidents and equipment damage check generation system every time before starting engine e Keep the generator a distance at least 1 meter from other equipment during operation Keep the generator upright when running If generator is tilted it may cause fuel spillage e Generator operators must be trained must know how to stop the generator quickly and understand the operation of all controllable parts Untrained operators should not be allowed to use this equipment e Keep children and pets away from operating area e Keep away from rotating parts during operation The generator is a potential source of electrical shock when misused Do not operate it with wet hands or in any wet location Do not operate the generator in rain or snow or let it get wet WARNING Read this manual carefully before using the machine for your own safety You should only use the generator according to these instructions COMPONENT IDENTIFICATION 1 Fuel cap 9 Overload indicator light 2 Air vent knob 10 Output indicator light 3 Choke knob 11 Oil alert indicator light 4 Control panel 12 Eco throttle switch 5 Starting grip 13 Engine switch 6 Fuel valve grip 14 DC socket 7 Maintenance cover 15 DC
10. 1 2 turn with a wrench to compress its washer If a used plug is being reinstalled it should only require 1 8 to 1 4 turns after being seated 7 Reinstall the ignition coil rubber boot on the spark plug securely 8 Reinstall the controlling panel pr The spark plug must be securely tightened An improperly tightened plug can become very hot and possibly damage the generator Never use a spark plug with an improper heat range Never use a spark plug without damping resistance or it will cause no AC output Transporting and Storage To prevent fuel spillage when transporting or during temporary storage the generator should be secured upright in its normal operating position with the engine switch OFF The fuel cap vent lever is turned counter clockwise to the OFF position Allow the engine to cool well before turning the fuel cap vent lever to the OFF position When transporting generator Do not overfill the tank there should be no fuel in the filler neck e Do not operate generator while it is in a vehicle Take the generator out of the vehicle and use it in a well ventilated place e Avoid a place exposed to direct sunlight when putting the generator on a vehicle If the generator is left in an enclosed vehicle for many hours high temperature inside the vehicle could cause fuel to vaporize resulting in a possible explosion Do not drive on a rough road for an extended period with the generator on board If you must tr
11. S AND UNTRAINED PEOPLE Skari the engine The DC receptacle may be used while the AC power is in use An overloaded DC circuit will trip the DC circuit breaker If this happens disconnect the DC load before pushing in the circuit breaker to resume operation DC circuit breaker an alert system The oil alert system is designed to prevent engine damage caused by an insufficient amount of oil in the engine The alert system will automatically shut down the engine if a low oil level is detected the engine switch will remain in the ON position If the oil alert system shuts down the engine the oil alert indicator light red will come on when you operate the starter and the engine will not run If this occurs add engine oil Oil alarm indicator red Stopping the engine To stop the engine in an emergency turn the engine switch to the OFF position In normal use 1 Switch off the connected equipment and pull the inserted plug out Electric start key 3 Turn the cap level fully counter clockwise to the OFF position Turn the fuel valve knob to the OFF position Be sure to tighten the fuel cap and the engine switch are in OFF position when stopping transporting and or storing the generator Fuel cap SIE AER AES N SE SS The purpose of the maintenance and adjustment schedule is to keep the generator in the best operating condition e Inspect or service as scheduled in the t
12. able below Shut off the engine before performing any maintenance If the engine must be run make sure the area is well ventilated the exhaust contains poisonous carbon monoxide gas Use authorized parts or their equivalent The use of replacement parts which are not of equivalent quality may damage the generator Maintenance Schedule Regular service period 1 ITEM Each 3 Each 6 Each Perform at every indicated month or u mont months or months or operating hour interval whichever comes 20HR SOHRS 100HRS first Engine O enek Rete ee gt ireleaner Check JP ae a Spark plug Clean amp adjust Combustion Clean chamber Check amp adjust Fuel tank and Clean filter tank Fuel line Check Every 2 years replace if necessary as 3 Note 1 Log hours of operation to determine proper maintenance 2 Service more frequently when used in dusty areas 3 These items should be serviced by an authorized dealer unless the owner has the proper tools and is mechanically proficient See the Shop Manual Temperature Time for changing oil Recommended power PT AEE a Normal 100 o TE 15 85 Changing oil Drain the oil while the engine is still warm to assure rapid and complete draining Make sure to turn the engine switch and the fuel cap vent lever OFF before draining 1 2 3 4 Lean the generator Fasten the oil lead pipe on the oil exhaust as the
13. ansport the generator on a rough road drain the fuel from the generator beforehand Before storing the unit for an extended period 1 Be sure the storage area is free of excessive humidity and dust 2 Drain the fuel Gasoline is extremely flammable and explosive under certain conditions Do not smoke or allow flames or sparks in the area 3 Completely drain the fuel from the tank Open the fuel valve start the engine and operate it in the idle position until all remaining fuel is gone and the engine stops automatically 4 Discharge oil SP 6 Gasoline pot Remove spark plug and fill cylinder with 2cc s fresh oil Pull start cord 3 4 times to discharge the remaining oil Then reinstall the spark plug Pull the staring cord slowly until resistance is strong At this time the piston is moving to the top of the compression stroke and the valves will be closed Starting grip Fire net muffler service A dirty muffler will increase noise and affect the engine s running Clean and maintain the fire net regularly to make sure the generator works normally The fire net of the muffler needs cleaning frequently if you use the generator in very dirty conditions and replace the fire net if necessary Before clean the fire net of muffler make sure the generator is not running Before check and maintenance the fire net of the muffler make sure the generator is cool or risk being burned by the hot muffler Remove
14. ated area with the engine stopped e Keep away from cigarettes smoke and sparks when re fuelling the generator Always refuel in a well ventilated location e Clean up spilled gasoline at once e Connections for standby power to a building s electrical system must be made by a qualified electrician and must comply with all applicable laws and electrical codes Improper connections can allow electrical current from the generator to back feed into the utility lines Such back feed may electrocute utility company workers or others who contact the lines during a power outage and when utility power is restored the generator may explode burn or cause fires in the building s electrical system e Always make a pre operation inspection before you start the engine You may prevent an accident or equipment damage e Place the generator at least 1m 3ft away from buildings or other equipment during operation e Operate the generator on a level surface If the generator is tilted fuel spillage may result e Know how to stop the generator quickly and understand the operation of all the controls Never permit anyone to operate the generator without proper instructions e Keep children and pets away from the generator when it is in operation e Keep away from rotating parts while the generator is running The generator is a potential source of electrical shocks when misused do not operate with wet hands Do not operate the generator in
15. ator Output indicator light red light green Substantial overloading that continuously lights the overload indicator light red may damage the generator Marginal overloading that temporarily lights the overload indicator light red may shorten the service life of the generator Be sure that all appliances are in good working order before connecting them to the generator if an appliance begins to operate abnormally becomes sluggish or stops suddenly turn off the generator immediately Then disconnect the appliance and examine it for signs of malfunction Output and Overload Indicators The output indicator light green will remain lighted during normal operating conditions If the generator is overloaded or if there is a short in the connected appliance the output indicator light green will go OFF the overload indicator light red will go ON and current to the connected appliance will be shut off Stop the engine if the overload indicator light red switches ON and investigate the overload source Before connecting an appliance to the generator check that it is in good order and that its electrical rating does not exceed that of the generator Then connect the power cord of the appliance and start the engine Be sure all equipment is turned off before plugging in the power cord Overload indicator red Output indicator green Oil alarm indicator When an electric motor is started both the
16. fully before operating the generator or it may Cause serious injury and equipment damage AE WARNING e Exhaust contains poisonous carbon monoxide Do not operate generator in confined environment or with an aerator Only use outdoors and far from open windows doors and vents Ant WARNING The muffler becomes very hot during operating and remains hot for a While after stopping the engine Be careful not to touch the muffler while it is hot Let the engine cool before storing the generator indoors e The engine exhaust system will be heated during operation and remain hot immediately after stopping the engine To prevent scalding pay attention to the warning marks attached to the generator ALI WARNING Do not parallel connect other cables to receptacles You must use the special jack or it may cause an electrical shock i Gasoline is extremely flammable and is explosive under certain conditions e Refuel in a ventilated area with engine stopped Keep away from cigarettes smoke and sparks when refuelling the generator Always refuel in a well ventilated location WARNING Connection for standby power to a building electrical system must be made by a qualified electrician The connection must isolate the generator from utility power and must comply with all applicable laws and electrical codes Improper connections to a building electrical system can allow electrical current from the generator to backfeed into
17. in or breathing of vapour KEEP OUT OF REACH OF CHILDREN Check the air cleaner Check the air cleaner element to be sure it is clean and in good condition 1 Loosen the cover screw and remove the left side maintenance cover 2 Press the latch tab on the top of the air cleaner body remove the air cleaner cartridge and check the element 3 Clean or replace the element if necessary Access panel screws Access panel Never run the engine without the air cleaner Rapid engine wear will result from contaminants such as dust and dirt being drawn through the carburettor into the engine It is normal for a little oil to appear under the air filter box if the generator is running for a long period of time or a lot of oil is in the engine Wipe up excess oil after each use and after stopping the generator GENERATOR USE Starting the engine Before starting the engine disconnect any load from the DC receptacle The first time starting the engine or restarting the engine after a long time by electric starter if the engine can t be started please use the recoil starter to start the engine 1 Turn the fuel cap lever fully clockwise to the ON position oy pe Er pr w EE AN g sun fa f Electric start key 2 Put the electric start key into engine switch and turn it to ON position 3 Turn the electric start key to START position until the engine has started Starting the engine Recoi
18. int solvents for cleaning They are flammable and explosive under certain conditions 1 Loosen the cover screw and remove the access panel 2 Remove the screw under the air filter case 3 Pull the air filter cartridge down 30mm and remove the air filter cartridge 4 Remove the air filter iron clip and check the air filter element Clean or replace the element if necessary 5 Reinstall the air filter parts after cleaning or replacing air filter element Air cleaner tridge Air cleaner element benon Access panel screws d SEE F P 4 J i hm hm _ eu a Access panel Spark Plug Servicing Please use high quality authentic spark plugs To ensure proper engine operation the spark plug must be properly gapped and free of deposits 1 Remove the bolts on the top maintenance cover and the cover Maintenance cover Screw e ignition coil rubber boot 3 Remove the spark plug with the spark plug wrench insert the screwdriver into the hole of the spark plug wrench and remover the spark plug E SZ ignition coil rubber boot 4 Visually inspect the spark plug Discard it if the insulator is cracked or chipped Clean spark plug with a wire brush if it is to be reused 0 6407 A 0 0440 028in Install the spark plug carefully by hand to avoid cross threading After a new spark plug has been seated by hand it should be tightened
19. l Starter 1 Turn the fuel cap lever fully clockwise to the ON position 3 Pull the starting grip lightly until resistance is felt then pull briskly to start the engine High Altitude Operation At high altitude the standard carburettor air fuel mixture will be excessively rich Performance will decrease and fuel consumption will increase High altitude performance can be improved by installing a smaller diameter main fuel jet in the carburettor and readjusting the slow tempo screws If you always operate the generator at altitudes higher than 1 500m 4 000 feet above sea level have your dealer perform these carburettor modifications Even with suitable carburettor jetting engine horsepower will decrease approximately 3 5 for each 300m 1 000 feet increase in altitude The effect of altitude on the horsepower will be greater than this if no carburettor modification is made Operation of the generator at an altitude lower than the carburettor is jetted for may result in reduced performance overheating and serious engine damage caused by an excessively lean air fuel mixture Generator Use Warning To prevent electrical shock from faulty appliances the generator should be grounded Connect an electric conductor cable of at least 1 5mm2 between the generator s ground terminal and an external ground source e Connections for standby power to a building s electrical system must be made by a qualified elect
20. overload indicator light red and the output indicator light green may go on simultaneously This is normal if the overload indicator light red goes off after about four seconds If the overload indicator light red stays on consult your dealer 1 Connect the ground terminal L ET 14 Grounding mark A Bu N 2 Start engine according to STARTING THE ENGINE When the output indicator light green does not light and the overload indicator light red lights instead set the engine switch to STOP stop the engine at once and then start the engine again 3 Confirm that the equipment to be used is switched off and insert the plug of the equipment to be used into the AC receptacle unit A Check that the equipment to be connected is switched off When the equipment to be used is switched on it can start suddenly and injuries or accidents may be caused 4 Switch on the equipment and the output indicator light will light up In case of overload operation or when trouble occurs for the equipment being used the output indicator light green will go out the overload indicator light red will light continuously and no power will be put out At this time the engine will not automatically stop so it must be stopped by setting the respective engine switch to STOP When overload or short circuited Normal output overload indicator will indicator will illuminate red V illuminate When equipment requires a
21. partment will issue instructions so please contact them before returning the charger Proof of Purchase will be required for all warranty claims MATEN poy The Matson Group Pty Ltd 100 Links Road St Marys NSW 2760 Australia Ph 02 9833 3444 Fax 02 9833 3500 sales matson com au www matson com au
22. picture Then pour out the oil Refill the new oil and check the oil position in the crankcase After refill the new oil into the crankcase please shake the generator left to right a few times and make sure the bobber of the oil alarm system is floating Reinstall the side maintenance cover and tighten the cover screw securely Engine oil capacity 1 0L kn Remove the jetting oil bolts Refill oil 1 Remove the screws and open the access panel 2 Revolve out the dipstick 3 Revolve the oil filling pipe into the oil filter hole 4 Use the oil filling bottle to pour the oil into the crankcase and check the oil level Oil filling pipe i Oil filling bottle Ce a EE ns __ After refilling the new oil into the crank case please shake the generator left to right a few times and make sure the bobber of the oil alarm system is floating Wash your hands with soap and water after handling used oil Please dispose of used motor oil in a manner that is considerate of the environment We suggest you take it in a sealed container to your local service station for disposal Do not throw it in the trash or pour it on the ground Air Cleaner Service A dirty air cleaner will restrict air flow to the carburettor To prevent carburettor malfunction service the air cleaner regularly Service more frequently when operating the generator in extremely dirty areas Do not use gasoline or low flash po
23. r Does the electrical equipment Restart the engine after turning off the work when plugged in directly overload indicator v Yes Send the generator to an authorized dealer 1 Replace the electric equipment 2 Repair the electric equipment There is no power in the direct current electric outlet Is there electric circuit breaker intact Replace the electric circuit breaker Send the generator to an authorized dealer There is no power in the DC electric outlet Is there electric circuit breaker intact Replace the electric circuit breaker Send the generator to an authorized dealer Deficient AC output Deficient output Check air filter dirty Clean or replace air filter element Check fire net of muffler dirty Clean or replace fire net Check the gasoline is bad YES Replace gasoline Return the generator to an authorized dealer Specifications G4000X L x W x H mm 600 x 450 x 500 Net weight kg Engine Specifications Displacement Compression ratio Engine speed Cooling system ignition system Oil capacity Fuel tank capacity Spark plug NK gt Noise level 4m Continuous Operation Generator Specifications Z Q A O OD Type Item Part Number AC output Rated output KVA Maximum output KVA 5 0 00 8 cos DC output For 12V Rated voltage V automotive batteries Rated current A only Wiring Diagram eae sets so inverter Exploded Pa
24. rician and must comply with all applicable laws and electrical codes Improper connections can allow electrical current from the generator to back feed into the utility lines Such back feed may electrocute utility power is restored the generator may explode burn or cause fires in the building s electrical system Do not exceed the current limit specified for any one receptacle Do not connect the generator to a household circuit This could cause damage to the generator or to electrical appliances in the house Do not modify or use the generator for any other purpose than it is intended for Also observe the following when using the generator Do not connect generators in parallel Do not connect an extension to exhaust pipe When an extension cable is required be sure to use a rubber sheathed flexible cable Limit length of extension cables 60m for cables of 1 5mm2 and 100m for cables of 2 5mm2 Keep the generator away from other electric cables or wires such as distribution network The DC receptacle can be used while the AC power is in use If you use both at the same time be sure not to exceed the total power for AC and DC Most appliance motors require more than their rated wattage for start up AC applications 1 2 Start the engine and make sure the output indicator light green illuminates Confirm that the appliance to be used is switched off and plug in the appliance Overtoad indic
25. rts View MO Prte Doseriptien MO Parte goreription t Engine Assembl 50 Topcover o lt 2 M8X40Bot 51 M6X12Bot a ion cot s2 Fueltank sleeve 4 Stator Assembly 53 Fuel cap Fuel level display cover board g M6 X50 Inner 6 Cornus Bolt SN Pipe fuel tank M4 2 x10 self tapping screw 42 M6X 18 Bolt gg Engine Bracket 64 Mt0x30bot Absorber Rear cover M6 x12plate screw or 88 Handle stoppe gt 69 M xt2bot Handle spongs sleeve 72 Mt vote tame 75 ue xtplate seen EE gt B2 Wheels with brake Chassis Carburetor connection pipe Frame Fuel valve aux X 12 Bolt 5 mer assembly Inductance M6 X 12 Bolt Right side board Bush Power Warranty Against Defects Procedure Bush Power A subsidiary of The Matson Group Pty Ltd 100 Links Rd St Marys NSW 2760 Phone 02 98333444 Email sales matson com au www matson com au Warranty Bush Power warrants its products to be free of defects for reasonable consumer use for a period of 12 months Bush Power will repair or replace the warranted product and it will return the repaired products under warranty to the consumer at Bush Power s cost To make a claim under this warranty the consumer must advise Bush Power of the defect as soon as it becomes apparent within 12 months of the purchase date and obtain a return authority by phoning Bush Power on the above number provide satisfactory proof of purchase and send
26. the M6 screws and open the muffler cover Remove two M4 screws on the fire net Take down the fire net as per the following figure Check the fire net clean or replace it if necessary ee bg Muffler cover TROUBLESHOOTING Engine will not start NO Enough fuel Add fuel Turn them to the on position Add more qualified oil Is there fuel in the carburetor Start a few times to ensure that fuel enters the carburetor Spark plug works or not NO NO Send the generator to an authorized dealer Shake the generator several times from side to side to make the oil float rise if the generator cannot start after adding oil for the first time and the oil alarm indicator stays on when pulling the starting cord Make sure there is no spilled fuel around the spark plug Spilled fuel may ignite If the engine still doesn t start have the generator repaired by a licensed repair person INSPECTION 1 Remove the spark plug rubber boot and clean any dirt from around the spark plug 2 Remove the spark plug and place it in the spark plug rubber boot 3 Connect the side electrode of the spark plug to the metal parts of the engine 4 Pull the starting cord A spark could jump across the gap 2 S LT lo lt AE JE i Spark plug Ignition coil rubber foot The equipment that connects generator doesn t start v YES Is the overload indicator on Send the generator to an authorized deale
Download Pdf Manuals
Related Search