Home
Nuclear Gauge Testing Manual Section 4 Operating Instructions
Contents
1. p Press and use the numbered keys to enter a value of 0 0 and hold Press to retain the displayed value Issue Date October 2003 Pagel of 2 The State of Queensland Department of Main Roads 2003 NuclearGauge Testing Manual Operating Instruction N317 4 Asphalt Density Bias There is no facility to enter the asphalt density bias using the keypad 5 Material Moisture Bias SET Press If a value of 0 0 is displayed SET Press SHIFT to retain the displayed value RDK K If a value other than 0 0 is displayed Press and use the numbered keys to enter a value of 0 0 and hold SET Press to store the value Press OFF if the nuclear gauge is not required for further use Issue Date October 2003 Page 2 of 2 The State of Queensland Department of Main Roads 2003 Queensland Government Nuclear Gauge Testing Manual OS Deparimentot Main Roads OPERATING INSTRUCTION N318 MEASUREMENT ASPHALT HUMBOLDT 5001P 1 Start up Press and allow the nuclear gauge to stabilise for at least ten minutes before commencing the test 2 Measurement F C XXX gt Press and the following will be displayed XX At the end of the counting period the following will be displayed XXXX X dg BE Record the displayed value as the density count Press and record the displayed value as the wet density to the w nearest 0 01 t m Bg To convert from kg m to t m div
2. 3 XXXX 4 XXXX 5 New 6 Disable 6 1 Disable Material Moisture Bias P Press The following will be displayed The display will return to lt READY gt Go to Step 8 6 2 Enable the Material Moisture Bias gt Press the number corresponding to any of the stored values 6 3 Change a Material Moisture Bias Value Select Offset Source a the following is displayed 1 Manual Entry 2 Gauge Derived gt Press For manual entry bth ae True Moisture gt Press 1 the following is displayed Xxx Press ENTER Use the numbered keys to enter the average oven dry moisture content to the nearest 0 01 RE Gauge Moisture 96 P Press ENTER the following is displayed 0 00 Press lt ENTER gt Issue Date March 2013 Page 5 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N323 Use the numbered keys to enter the average standard blocks moisture content to the nearest 0 0146 ENTER I D P Press starr the following is displayed Do you want to save this value for later use To save the displayed value Select Memory Cell P Press YES the following is displayed a P Press to Select Press a numbered key 1 2 3 or 4 to select a memory location in which to save the value KEX The following will be displayed briefly ENABLED If the value is not to be displayed gt Press NO
3. P Press DEPTH gt Press and the following is displayed ASPHALT XXXX Select 1 MA 2 100 MA COUNT gt Press and the following is displayed ASPHALT MA Do you want to enable voids also YES EEE ASPHALT MA gt Press f xr and the following is displayed VOIDS OR NO CE MT CCE and the following is displayed ASPHALT MA Issue Date March 2013 Page 2 of 9 The State of Queensland Department of Transport and Main Roads 2013 x N Nuclear Gauge Testing Manual Operating Instruction N301 The display will return to cz READY P Press SHIFT MODE and the following is displayed ar ai 2 ASPHALT CE to exit P Press gt Press and the following is displayed ASPHALT XXXX Select 1 MA 2 100 MA P Press and the following is displayed ASPHALT 100 MA Do you want to enable voids YES TNNT ASPHALT 100 MA P Press f xr and the following is displayed VOIDS OR NO CE RE CBE and the following is displayed ASPHALT 100 MA The display will return to lt READY gt x g g m m m v m v E 4 I I Issue Date March 2013 Page 3 of 9 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N301 3 MAXIMUM DENSITY PROCTOR MA XXXX kg m3 MARSHALL ine isdi PR XXXX P Press and the following is displayed VD XXXX Want to change To reta
4. The following will be displayed briefly The display will return to lt READY gt Issue Date March 2013 Page 5 of 5 The State of Queensland Department of Transport and Main Roads 2013 THIS PAGE IS INTENTIONALLY BLANK EL y Nuclear Gauge Testing Manual X D Queensland DIA A XA Government OPERATING INSTRUCTION N320 MEASUREMENT ASPHALT INSTROTEK XPLORER 3500 1 START UP gt Press and allow the nuclear gauge to complete the self test routine 2 MEASUREMENT When READY is displayed START ee ee Time XX sec P Press ENTER and the following is displayed Depth XX mm At the end of the counting period gt Press DOWN repeatedly until the required values are displayed Record the following values as appropriate 7 WD as the wet density to the nearest 0 001 t m 7 D Count as the density count To convert from kg m to t m divide the displayed value by 1000 ON P Press ves and the display will return to lt READY gt OFF P Press No if the nuclear gauge is not required for further use Issue Date March 2013 Page 1 of 1 The State of Queensland Department of Transport and Main Roads 2013 THIS PAGE IS INTENTIONALLY BLANK m MENT REN OH te SEM Queensland Nuclear Gauge Testing Manual Government OPERATING INSTRUCTION N321 TEST PARAMATERS ASPHALT TROXLER 3440P 1 START UP Turn the power switch on and allow the nuclear gauge to compl
5. 1 Disable Material Wet Density Bias The following will be displayed briefly Density Offset DISABLED The display will return to lt READY gt Go to 7 5 2 Enable Material Wet Density Bias Issue Date March 2013 Page 3 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N321 a i Density Offset The following will be displayed E m ENABLED 5 3 Change Material Wet Density Bias JS Density Offset P Press 3 the following is displayed xx kg m3 Select Input and ENTER Use the numbered keys to enter the required value to the nearest 1 kg m To convert from t m by 1000 to kg m multiply the material wet density bias P Press ENTER START The following will be displayed briefly The display will return to lt READY gt 6 MATERIAL MOISTURE BIAS OFFSET Select gt Press OFFSET the following is displayed 1 Dens OFF The following will be displayed 2 Moist OFF 3 Trench OFF Issue Date March 2013 Page 4 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N321 Moisture Offset 1 XXXX 2 XXXX 3 XXXX 4 XXXX 5 New 6 Disable 6 1 Disable Material Moisture Bias P Press The following will be displayed The display will return to lt READY gt Go to Step 8 6 2 Enable the
6. 4 3 min Count Time gt Press and the following will be displayed Jupes The display will return to lt READY gt 4 Layer Thickness Layer Thickness X XX cm gt Press THICK and the following will be displayed Input and MR Press ENTER gt Use the numbered keys to enter the layer thickness to the nearest 0 1 cm The minimum value that can be set is 2 54 cm f Layer Thickness Press START and the following will be displayed X XX cm ENTER briefly The display will return to lt READY gt Issue Date October 2003 Page 2 of 7 The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N307 5 Marshall and Maximum Voidless Density MA X XXX g cm3 VD X XXX g cm3 Press MA and the following will be displayed EE to change Q J m Y D If MA and VD values of 0 000 g cm are displayed NO CE C CE Press If values other than 0 000 g cm are displayed MARSHALL X XXX g cm3 Input and Press ENTER gt Press YES and the following will be displayed m x y RECALL Press VOIDLESS DENSITY gt Press SARV and the following will be displayed aa E nput an Press ENTER RECALL gt Press R Press E and the display will return to READY Issue Date October 2003 Page3 of 7 The State of Queensland Department of Main Roads 2003 NuclearGauge Testing Manual Operating
7. Disable 3 Change Offset To disable the material wet density bias go to Step 6 1 To enable the material wet density bias go to Step 6 2 To change the material wet density bias go to Step 6 3 5 1 Disable Material Wet Density Bias The following will be displayed briefly Density Offset DISABLED The display will return to lt READY gt Go to 7 5 2 Enable Material Wet Density Bias Issue Date March 2013 Page 3 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N323 a i Density Offset The following will be displayed E ENABLED 5 3 Change Material Wet Density Bias JS Density Offset P Press 3 the following is displayed xx kg m3 Select Input and ENTER Use the numbered keys to enter the required value to the nearest 1 kg m To convert from t m by 1000 to kg m multiply the material wet density bias P Press ENTER START The following will be displayed briefly The display will return to lt READY gt 6 MATERIAL MOISTURE BIAS OFFSET Select gt Press OFFSET the following is displayed 1 Dens OFF The following will be displayed 2 Moist OFF 3 Trench OFF Issue Date March 2013 Page 4 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N323 Moisture Offset 1 XXXX 2 XXXX
8. Instruction N307 6 Asphalt Density Bias OFFSET Press SHIFT Xx Offset DISABLED Offset ENABLED The following will be XX g cm3 XX g cm3 displayed 1 Enable Change 1 Enable Change 2 Disable 2 Disable To disable the asphalt density bias go to Step 6 1 To enable the asphalt density bias go to Step 6 2 6 1 Disable Asphalt Density Bias Offset DISABLED Press and the following will 2 be displayed briefly The display will return to c READY 6 2 Enable Asphalt Density Bias Offset ENABLED SP CAL XX g cm3 Press 1 and the following will be displayed Want to change offset value To retain the displayed value go to Step 6 2 1 To change the displayed value go to Step 6 2 2 Issue Date October 2003 Page4 of 7 The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N307 6 2 1 Retain the Value Press NO CE C CE The display will return to lt READY gt 6 2 2 Change the Value Select source Press YES and the following will be displayed of Offset EXIT 1 keyboard 2 stored value To enter a new value go to Step 6 2 2 1 To select a stored value go to Step 6 2 2 2 6 2 2 1 Enter a New Value Offset value g cm3 Press and the following will be displayed Select i 1 2 Press to enter a OR to enter a positive bias negative bias Offset value X g cm3 The following wi
9. Queensland Nuclear Gauge Testing Manual Government OPERATING INSTRUCTION N323 TEST PARAMATERS ASPHALT TROXLER 3430P 1 START UP Turn the power switch on and allow the nuclear gauge to complete the self test routine 2 MEASUREMENT UNITS When READY is displayed gt Press SETUP The following will be displayed Metric Units The following will be briefly displayed Kg m3 ENABLED The display will return to lt SETUP gt 3 COUNT TIME P Pres SETUP Issue Date March 2013 Page 1 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N323 n TIME XX gt Press 1 and the following is displayed 1 15 sec 2 1 min The following will be briefly displayed The display will return to lt READY gt 3 4 min 4 ASPHALT MODE The following will be displayed 2 SOIL Press to Select l l Asphalt Mode The following will be displayed briefly ENABLED The display will return to lt READY gt MODE XXXX Select 1 ASPHALT Issue Date March 2013 Page 2 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N323 3 MATERIAL WET DENSITY BIAS EP OFFSET P Press OFFSET the following is displayed Dan ORE 2 Moist OFF 3 Trench OFF The following will be displayed Density Offset xx kg m3 1 Enable 2
10. Queensland Government Nuclear Gauge Testing Manual Departmentof Main Roads OPERATING INSTRUCTION N305 TEST PARAMETERS ASPHALT TROXLER 3411B 1 Start up gt Turn the PWR TIME switch to NORM 2 Depth gt Set the DEPTH switch to the BS position 3 Maximum Wet Density gt Press SHIFT EA simultaneously Set the switch to i e set to decrease the displayed value Hold usb repeatedly until the required value is obtained to the nearest Or press 1 kg m To convert from t m to kg m multiply the maximum dry density by 1000 The display will return to normal mode after a few seconds if no key is pressed 4 Material Moisture Bias Set the MOISTURE CORRECTION switches to 0 Turn the PWR TIME switch to OFF if the nuclear gauge is not required for further use Issue Date October 2003 Page 1 of 1 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual OS Deparimentot Main Roads OPERATING INSTRUCTION N306 MEASUREMENT ASPHALT TROXLER 3411B 1 Start up Turn the PWR TIME switch to NORM and allow the nuclear gauge to stabilise for at least 20 minutes before commencing the test 2 Measurement Press a MEA At the end of the counting period the following will be displayed XXXX Record the displayed value as the density count MAR Press a
11. The display will return to lt READY gt For gauge derived True Moisture P Press 2 the following is displayed AE Press ENTER Use the numbered keys to enter the true moisture content to the nearest 0 01 x Place gauge on soil P Press ENTER the following is displayed ues M and Press any key Place the gauge on the measurement site and press any key Issue Date March 2013 Page 6 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N323 F K At the completion of the counting period the following will OH EVENE be displayed Later Use To save the value P Press YES To enable the value without storing gt Press NO 7 TRENCH OFFSET OFFSET 1 Dens OFF gt Press orrseT the following is displayed 2 Moist OFF 3 Trench OFF Trench Offset the following is displayed M 0 D O 1 Enable 2 Disable 3 Change Offset P Press gt To enable the trench offset gt Press 1 The following is displayed en To disable the trench offset Issue Date March 2013 Page 7 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N323 gt Press 2 The following is displayed a To change the trench offset gt Press 3 Place Gauge in The following is displayed ee Press lt START g
12. disable the moisture offset gt Press and following is displayed Moisture Offset DISABLED To enable the moisture offset Issue Date March 2013 Page 4 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual gt Press and following is displayed 6 1 1 Change the Value P Press 3 To select a stored offset P Press 1 and the following is displayed and the following is displayed Operating Instuction N325 Moisture Offset ENABLED Moisture Offset 1 Stored Offset 2 Gauge Derived 3 Keypad Entry Moisture Offset Select K Value Cell 1 0 00 2 0 00 3 0 00 4 0 00 gt Use the numbered keys to enter the required value to the nearest 0 01 The display will return to lt READY gt 6 1 2 Change to a Gauge Derived Value To change the moisture bias to a gauge derived value gt Press 3 and the following is displayed gt Press 2 and the following is displayed gt Press 1 and the following is displayed Issue Date March 2013 Moisture Offset 1 Stored Offset 2 Gauge Derived 3 Keypad Entry Gauge Derived Moisture Offset 1 Measure Moisture 2 Input True Moist Place Gauge On Surface To Be Tested Press START For 4 One Minute Counts Page 5 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N325 gt Press START
13. gt 3 MATERIAL WET DENSITY BIAS OFFSET Select gt Press FFSET and the following is displayed OFES amp pay 1 Wet Density OFF 2 Moisture OFF 3 Trench OFF Issue Date March 2013 Page 2 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N325 The following will be displayed Wet Density Offset XXXX kg m Enable 2 Disable 3 Change Offset To disable the material wet density bias gt Press and following is displayed Wet Density Offset DISABLED To enable the material wet density bias gt Press and following is displayed Wet Density Offset ENABLED 5 1 1 Change the Value TP Wet Density Offset gt Press 3 and the following is displayed xxxx kg m Select Issue Date March 2013 Page 3 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N325 gt Use the numbered keys to enter the required value to the nearest 1kg m gt Press ENTER The following will be displayed Density Offset ENABLED The display will return to lt READY gt 6 MATERIAL MOISTURE BIAS M OFFSET Select P Press OFFSET and following is displayed 1 Wet Density OFF 2 Moisture OFF The following will be displayed 3 Trench OFF Moisture Offset K 0 00 1 Enable 2 Disable 3 Change Offset To
14. to the main menu Press dis if the nuclear gauge is not required for further use Issue Date October 2003 Page 1 of 1 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual Rr Depanmenot Main Roads OPERATING INSTRUCTION N315 TEST PARAMETERS ASPHALT HUMBOLDT 5001C 1 Start up gt Press gt Press CLEAR SFT simultaneously until SAF ENTER the following is displayed and allow the nuclear gauge to complete the initialising routine 2 Asphalt Mode F Press m repeatedly until ASPH is displayed Press 3 Maximum Density gt x oO LWRD Press and the following will be displayed If a value of 0 0 is displayed CLEAR Press prm to retain the displayed value Issue Date October 2003 Pagel of 2 The State of Queensland Department of Main Roads 2003 NuclearGauge Testing Manual Operating Instruction N315 If a value other than 0 0 is displayed Press and use the numbered keys to enter a value of 0 0 and hold Press repeatedly until the following is displayed SAF 4 Asphalt Density Bias There is no facility to enter an asphalt density bias using the keypad Press OFF if the nuclear gauge is not required for further use Issue Date October 2003 Page 2 of 2 The State of Queensland Department of Main Roads 2003 Queensland Government Nucle
15. to the nearest 0 01 x Place gauge on soil P Press ENTER the following is displayed ues M and Press any key Place the gauge on the measurement site and press any key Issue Date March 2013 Page 6 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N321 F K At the completion of the counting period the following will OH EVENE be displayed Later Use To save the value P Press YES To enable the value without storing gt Press NO 7 TRENCH OFFSET OFFSET 1 Dens OFF gt Press orrseT the following is displayed 2 Moist OFF 3 Trench OFF Trench Offset the following is displayed M 0 D O 1 Enable 2 Disable 3 Change Offset P Press gt To enable the trench offset gt Press 1 The following is displayed en To disable the trench offset Issue Date March 2013 Page 7 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N321 gt Press 2 The following is displayed EOD To change the trench offset P Press 3 Place Gauge in The following is displayed Eee Press START ENTER P Pres START At the end of the counting period the display will return to lt READY gt Turn the power switch off if the nuclear gauge is not required for further use Issue Date March 2
16. 013 Page 8 of 8 The State of Queensland Department of Transport and Main Roads 2013 Queensland Government MEN y Nuclear Gauge Testing Manual ay CLTN OPERATING INSTRUCTION N322 MEASUREMENT ASPHALT TROXLER 3440P 1 START UP Turn the power switch on and allow the nuclear gauge to complete the self test routine 2 MEASUREMENT When READY is displayed Depth XX mm PR XXXX kg m3 gt Press ENTER the following is displayed Time XX sec In the manual depth mode the gauge will prompt for the source rod depth In automatic mode the gauge software reads the depth strip on the source rod to determine the depth At the end of the counting period the following will be WD xxxx displayed M x M X X Record WD as the wet density P Press ESC gt Press RECALL gt Press V DC 2 xxxx The following will be displayed Issue Date March 2013 Page 1 of 2 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N322 Record the following values as appropriate DC as the density count MC as the moisture count P Press ESC and the display will return to lt READY gt p Turn the power switch off if the nuclear gauge is not required for further use Issue Date March 2013 Page 2 of 2 The State of Queensland Department of Transport and Main Roads 2013 m MENT REN OH te SEM
17. 14 THIS PAGE IS INTENTIONALLY BLANK EN Nuclear Gauge Testing Manual je i Queensland AS Government OPERATING INSTRUCTION N328 MEASUREMENT ASPHALT CPN MC1 AND MC3 ELITE 1 SET UP gt Press and allow the nuclear gauge to complete the self test routine 2 MEASUREMENT When the ready screen is displayed Depth XX mm gt Press EXER and the following is displayed TER Time XX sec At the end of the counting period the gauge will display M Count D Count MCR DCR Press UP DOWN WD kg m3 MA 1HHHE VOIDS 1HHEE Press UP DOWN Moist kg m3 DD kg m3 Mois 4 4 PR Press UP DOWN Issue Date December 2013 Page 1 of 2 The State of Queensland Department of Transport and Main Roads 2014 Nuclear Gauge Testing Manual Operating Instruction N304 Record the following values WD as the wet density to the nearest 0 001 t m 7 D Count as the density count To convert from kg m to t m divide the displayed value by 1000 P Press and the display will return to the ready screen OFF i i gt Press NO if the nuclear gauge is not required for further use Issue Date December 2013 Page 2 of 2 The State of Queensland Department of Transport and Main Roads 2014
18. C1DR P The MCIDR has no keypad facility to set parameters 1 Asphalt Mode Press ENTER Press repeatedly until the following is displayed BE ME HE ME EE gt gt x x Press em Press STEP repeatedly until a value less than 1 000 g cm is displayed a value of 0 0 g em is preferred START Press EXIT Issue Date October 2003 Pagel of 1 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual OS depart OPERATING INSTRUCTION N312 MEASUREMENT ASPHALT CPN MC1DR MC1DR P 1 Measurement gt Press At the end of the counting period Wet Den X XX the following will be displayed MC IDR Moi Den X XX MC IDR P am n Record Wet Den or TotDen as the wet density to the nearest 0 001 t m gt Press repeatedly until the following is Be se displayed Record Dcount as the density count After 30 seconds the display will turn off Press to restore the display Issue Date October 2003 Pagel of 1 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual OS Deparment Main Roads OPERATING INSTRUCTION N313 TEST PARAMETERS ASPHALT HUMBOLDT 5001EZ 1 Start up Press PWR and allow the nuclear gauge to complete the initialising routine f l DATA XX XX XX The following will be displayed
19. Material Moisture Bias gt Press the number corresponding to any of the stored values 6 3 Change a Material Moisture Bias Value Select Offset Source a the following is displayed 1 Manual Entry 2 Gauge Derived gt Press For manual entry bth ae True Moisture gt Press 1 the following is displayed Xxx Press ENTER Use the numbered keys to enter the average oven dry moisture content to the nearest 0 01 RE Gauge Moisture 96 P Press ENTER the following is displayed 0 00 Press lt ENTER gt Issue Date March 2013 Page 5 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N321 Use the numbered keys to enter the average standard blocks moisture content to the nearest 0 0146 ENTER I D P Press starr the following is displayed Do you want to save this value for later use To save the displayed value Select Memory Cell P Press YES the following is displayed a P Press to Select Press a numbered key 1 2 3 or 4 to select a memory location in which to save the value KEX The following will be displayed briefly ENABLED If the value is not to be displayed gt Press NO The display will return to lt READY gt For gauge derived True Moisture P Press 2 the following is displayed AE Press ENTER Use the numbered keys to enter the true moisture content
20. Nuclear Gauge Testing Manual Section 4 Operating Instructions Testing Asphalt THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual CLT OPERATING INSTRUCTION N301 TEST PARAMETERS ASPHALT TROXLER 3440 1 SET UP gt Press and allow the nuclear gauge to complete the self test routine 2 UNITS When READY is displayed P Press SHIFT SPECIAL SPECIAL FUNCTION YES Next menu 1 STAT TEST 2 DRIFT TEST gt Press and the following is displayed di le Press YES repeatedly until the following is YES Next menu EXIT displayed 9 SET UNITS 10 BAND RATE 11 COMM PROTOCOL SPECIAL ERBEN UNITS in XXX gt Press ETE and the following is displayed Press 1 PCF 2 METRIC ENTER No change DEPTH MEET P Press CHE and the following is displayed UNITS IN METRIC 2 The display will return to READY Issue Date March 2013 Page 1 of 9 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N301 3 COUNT TIME TIME TP TIME XX gt Press and the following is displayed 1 15 sec 2 1 min 3 4 min DEPTH a R NT TIME P Press DEPTH and the following will be displayed ME in e The display will return to lt READY gt 4 ASPHALT MODE P Press SHIFT MODE MODE XXXX and the following is displayed Select 1 SOIL 2 ASPHALT CE to exit
21. SETUP XX XX XX ENGINEERING DEPTH SAF SET UP 2 gt Press and the following SET MEASUREMENT MODES will be displayed SET TRNCH COR SET TARGETS De Measurement Units SET DATE 1 SET TIME gt Press and the following er will be displayed Press F3 repeatedly until SP flashes MAIN Press MENU and the display will return to the main menu Issue Date October 2003 Page of 3 The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N313 3 Count Time FAST NORM SLOW 4MIN 16MIN The following will be displayed ASPH SOIL THIN AUTO MANUAL Press F1 repeatedly until NORM flashes 4 Asphalt Mode Press F3 repeatedly until ASPH flashes 5 Depth Press repeatedly until AUTO flashes MAIN Press and the display will return to the main menu 6 Maximum Density MAXD Press and the following INCREASE will be displayed DECREASE Issue Date October 2003 Page 2 of 3 The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N313 Press to decrease the displayed value until a value of 900 kg m is obtained Press MAIN and the display will return to the main menu MENU play 7s Asphalt Density Bias There is no facility to set an asphalt density bias using the keypad 8 Material Moisture Bias SET UP2 SET MEASURE MODES Press
22. T The gauge will display the progress of the standard count operation After the standard count the gauge displays Issue Date March 2013 Page 7 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N325 New Trench Offset TMO xxxx TDO xxxx xxxx Want To Accept To enable the new trench offset gt Press YES To create another trench offset P Press Issue Date March 2013 Page 8 of 8 The State of Queensland Department of Transport and Main Roads 2013 AM x Nuclear Gauge Testing Manual 62 97 Queensland Government OPERATING INSTRUCTION N326 MEASUREMENT ASPHALT TROXLER 3450 1 SET UP gt Press and allow the nuclear gauge to complete the self test routine 2 MEASUREMENT When READY is displayed gt Press START In the manual depth mode the gauge will prompt for the source rod depth In the automatic depth mode the gauge software reads the depth strip on the source rod to determine the source rod depth MA At the end of the counting period the following will be a displayed WD xxxx kg m VOIDS xxxx Record the following values MA as the percent Marshall to the nearest 0 1 7 WD as the wet density to the nearest 0 001 m VOIDS 100 x 1 WD VOIDLESS when enabled To convert from kg m to t m divide the displayed value by 1000 P Press Issue Date M
23. The gauge displays the progress of the measurements After each reading the gauge displays the results To continue to the next measurement gt Press START After the last measurement Serta ae Moisture Offset P Press ENTER and the following is displayed 1 Stored Partial Moisture Offset 2 Input True Moist To enter the true moisture later gt Press 4 To overwrite the partial offset gt Press YES To use the stored partial offset gt Press To enter the true moisture now Input True Moisture XXXXX gt Press 2 and the following is displayed ENTER When Done Issue Date March 2013 Page 6 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N325 7 TRENCH OFFSET EEE OFFSET Select P Press OFFSET and following is displayed 1 Wet Density OFF 2 Moisture OFF 3 Trench OFF Trench TMO xxxx TDO xxxx XXXX 1 Enable 2 Disable 3 Change Offset gt Press 3 and following is displayed To disable the trench offset Press 2 and following is displayed Trench Offset DISABLED To enable the trench offset gt Press 1 and following is displayed Trench Offset ENABLED To create a new trench offset Set Rod To STD Pos gt Press 3 and following is displayed Press START For 1 Minute STD Count In Trench Position the gauge inside the trench and gt Press STAR
24. XX kg m3 ENABLED stored in cell X The display will return to lt READY gt Go to 6 Issue Date March 2013 Page 5 of 9 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N301 5 4 Select a Stored Value COUNTS P i P Press and the following is displayed EE 1 XX2 XX 3 XX4 XX gt Press the numbered key 1 2 3 or 4 to select the required value Marshall And the following will be displayed XXXX kg m3 ENABLED The display will return to lt READY gt 6 VOIDLESS DENSITY MA XXXX kg m3 P Press MARSHALL and the following is displayed vs B T PROCTOR Want to change YES De Ja SELECT gt Press and the following is displayed 1 MA 2 PR 3 VOIDLESS TENET Voidless Density P Press ENS and the following is displayed XXXX kg m3 3 Press enter when complete Use the numbered keys to enter the required value to the nearest 1kg m P Press sTART Issue Date March 2013 Page 6 of 9 O The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N301 ENTER And the display will return to lt READY gt 7 MATERIAL WET DENSITY BIAS OFFSET OFFSET Select P Press and following is displayed 1 Dens ZZZ MR 2 Moist ZZZ 3 Trench ZZZ he Press COUNTS The following will be displayed Density Offset De
25. and the following SET TRENCH COR will be displayed SET TARGETS MAXD XXXX LWD XXXX gt Press and the following VAL EALLI a d INCREASE will be displayed DECREASE Press repeatedly until the KVAL value flashes Press repeatedly until a displayed value of 0 0 is obtained Press and the display will return to the main menu Press PWR if the nuclear gauge is not required for further use Issue Date October 2003 Page 3 of 3 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual Departmentof Main Roads OPERATING INSTRUCTION N314 MEASUREMENT ASPHALT HUMBOLDT 5001EZ 1 Start up gt Press PWR and allow the nuclear gauge to complete the initialising routine 2 Measurement TAKING MEASUREMENT Press and the following TIME REMAINING X XX will be displayed DC X MC X DEPTH BAC MEASURE ASPH RESULTS At the end of the counting period WD XXXX X 9eMA XXX X F AC X X MAXD XXXX the following will be displayed NEXTM DEPTH BAC Record WD as the wet density to the nearest 0 001 t m To convert from kg m to t m divide the displayed value by 1000 DC XXXX X DS XXXX X Press F4 and the following MC XX X MS XXX X will be displayed VR XX XX AV X XX LAST MDEPTH BAC Record DC as the density count MAIN 1 Press MENU and the display will return
26. ar Gauge Testing Manual OS Deparimentot Main Roads OPERATING INSTRUCTION N316 MEASUREMENT ASPHALT HUMBOLDT 5001C 1 Start up gt Press and allow the nuclear gauge to complete the initialising routine 2 Measurement gt Press Se simultaneously until the following is displayed TRENCH Press NORM and the following will be displayed At the end of the counting period the following will be displayed dg da Ua Record the displayed value as the wet density to the nearest 0 001 t m To convert from kg m to t m divide the displayed value by 1000 Press c and record the displayed value as the density count DC Press ur CHEAR simultaneously until the following is displayed gt Press OFF if the nuclear gauge is not required for further use Issue Date October 2003 Page 1 of 1 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual BS Deparment Main Roads OPERATING INSTRUCTION N317 TEST PARAMETERS ASPHALT HUMBOLDT 5001P 1 Start up Press and allow the nuclear gauge to complete the initialising routine 2 Depth Press OR repeatedly until the required measurement depth is displayed 3 Maximum Density SET Press PROD If a value of 0 0 is displayed SET curt MEME an Press ROD to retain the displayed value If a value other than 0 0 is displayed
27. arch 2013 Page 1 of 2 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N326 Counts And the following will be displayed DC Xxxxxx Xxxx Record the following values as appropriate DC for system 2 upper right reading as the density count P Press and the display will return to lt READY gt P Press OFF if the nuclear gauge is not required for further use Issue Date March 2013 Page 2 of 2 The State of Queensland Department of Transport and Main Roads 2013 Queensland Government Nuclear Gauge Testing Manual OPERATING INSTRUCTION N327 TEST PARAMETERS ASPHALT CPN MC1 AND MC3 ELITE 1 SET UP gt Press oe and allow the nuclear gauge to complete the self test routine 2 UNITS 1 Recall 2 Set depth gt Press MENU the first screen will be UP DOWN for next Select ESC exit 11 Auto scroll en An ge 12 Set units gt Press DOWN f the following is displayed UP DOWN for next Select ESC exit 1 PCF 2 kg m3 Press 12 button 1 then 2 3 GCC Select ESC exit 11 Auto scroll After selecting the unit of measurement the gauge 12 Set units returns to the menu screen UP DOWN for next Select ESC exit GAUGE READY COUNT TIME min gt Press ESC returns to ready screen Depth Offset N lt date gt lt time gt Issue Date December 2013 Page 1 of 3 The State of Queensland Department o
28. ayed UP DOWN or ENTER gt Press DOWN repeatedly until the required test depth is displayed o Z gt Press and the display will return to lt READY gt lt m n 5 ASPHALT MODE AND MAXIMUM DENSITY ENTER selects PR P Press and the following is displayed DOWN selects MA PR E MA XXXXX P Press DOWN and the following is displayed To retain the displayed value go to 5 1 H ar gt To change the displayed value go to 5 2 51 Retain Value gt Press OFF to retain the displayed value Zz The display will return to lt READY gt Go to 6 Issue Date March 2013 Page 2 of 5 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N319 5 2 Change the Value gt Press on to change the displayed value of MA lt The following is displayed For each digit gt Press DOWN repeatedly until the required number is displayed 4 gt JJ 3 gt Press to confirm each number m Z 3 m I The display will return to lt READY gt 6 MATERIAL WET DENSITY BIAS se oe saa cal RECALL gt Press MENU and the following is displayed UP DOWN or ENTER gt Press DOWN and the following is displayed UP EE TES Offset Density n 4 gt JJ 3 P Press Enter and the following is displayed UP DOWN or ENTER START ee Density Offset OFF P Press ENTER and the following i
29. ed 4 or ENTER Issue Date March 2013 Page 5 of 6 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N303 ART gt Press See and the following is displayed N T4 or enter For each digit until the required number is P Press displayed START P Press ENTER to confirm each number The display will return to cz READY Issue Date March 2013 Page 6 of 6 The State of Queensland Department of Transport and Main Roads 2013 EL y Nuclear Gauge Testing Manual X D Queensland DIA A XA Government OPERATING INSTRUCTION N304 MEASUREMENT ASPHALT TROXLER 3430 1 SET UP gt Press and allow the nuclear gauge to complete the self test routine 2 MEASUREMENT When READY is displayed START ae us Depth XX mm P Press Enter and the following is displayed T XX sec At the end of the counting period gt Press V repeatedly until the required values are displayed Record the following values as appropriate 7 WD as the wet density to the nearest 0 001 t m 7 D as the density count To convert from kg m to t m divide the displayed value by 1000 P Press ON and the display will return to lt READY gt if the nuclear gauge is not required for further use Issue Date March 2013 Page 1 of 1 The State of Queensland Department of Transport and Main Roads 2013 THIS PAGE IS INTENTIONALLY BLANK
30. et density SHIFT COUNTS P Press X 1 Dens ct XXXX Moist ct XX And following will be displayed SHIFT BECALL to see Readings Record Dens Ct as the density count gt Press OCF and the display will return to lt READY gt CICE gt Press OFF if the nuclear gauge is not required for further use Issue Date March 2013 Page 2 of 2 The State of Queensland Department of Transport and Main Roads 2013 EN Nuclear Gauge Testing Manual x Queensland DIA A AY Government OPERATING INSTRUCTION N303 TEST PARAMETERS ASPHALT TROXLER 3430 1 SET UP gt Press oe and allow the nuclear gauge to complete the self test routine 2 UNITS When READY is displayed P Press SPECIAL and the following is displayed repeatedly until the following is SET UNITS P Press y ad TU or ENTER n 2 JJ 3 UNITS P Press t4 or ENTER and the following is displayed P Press to set the desired unit m E z m m D o Z P Press and the display will return to lt READY gt lt m n 3 COUNT TIME gt Press TIME and the following is displayed i Dr gt Press to set the desired count time Issue Date March 2013 Page 1 of 6 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N303 O Z P Press and the display will return to READY lt m n 4 DEPTH gt Press DEPTH a
31. ete the self test routine 2 MEASUREMENT UNITS When READY is displayed gt Press SETUP The following will be displayed Metric Units The following will be briefly displayed Kg m3 ENABLED The display will return to lt SETUP gt 3 COUNT TIME P Press SETUP Issue Date March 2013 Page 1 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N321 n TIME XX gt Press 1 and the following is displayed 1 15 sec 2 1 min The following will be briefly displayed The display will return to lt READY gt 3 4 min 4 ASPHALT MODE The following will be displayed 2 SOIL Press to Select l l Asphalt Mode The following will be displayed briefly ENABLED The display will return to lt READY gt MODE XXXX Select 1 ASPHALT Issue Date March 2013 Page 2 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N321 3 MATERIAL WET DENSITY BIAS EP OFFSET P Press OFFSET the following is displayed Dan ORE 2 Moist OFF 3 Trench OFF The following will be displayed Density Offset xx kg m3 1 Enable 2 Disable 3 Change Offset To disable the material wet density bias go to Step 6 1 To enable the material wet density bias go to Step 6 2 To change the material wet density bias go to Step 6 3 5
32. f Transport and Main Roads 2014 Nuclear Gauge Testing Manual Operating Instruction N327 3 COUNT TIME Cnt Time min UP DOWN TO CHANGE P Press TIME and the following is displayed YES to Accept ESC to Exit P Press UP and DOWN to set the desired count time GAUGE READY COUNT TIME min gt Press YES returns to ready screen Depth Offset N lt date gt lt time gt 4 DEPTH The Elite gauge is equipped with an automatic non magnetic depth indicator The depth is automatically read as you lower the source into the measure position and the appropriate constants are selected to calculate the density The gauge can be placed into manual depth mode by disabling the Automatic depth mode from the MENU functions 5 ASPHALT MODE AND MAXIMUM DENSITY 1 Proctor 2 Max Dens gt Press and the following is displayed Select ESC exit MA PCF Change value gt Press 2 For Max Dens Press YES or NO ESC to Exit Issue Date December 2013 Page 2 of 3 The State of Queensland Department of Transport and Main Roads 2014 Nuclear Gauge Testing Manual Operating Instruction N327 Enter value for Max Dens PCF P Press YES ENTER to accept ESC to Exit Use the number buttons to change the value Once you have entered the PR value the gauge will return to ready screen Issue Date December 2013 Page 3 of 3 The State of Queensland Department of Transport and Main Roads 20
33. ide the displayed value by 1000 Press OFF if the nuclear gauge is not required for further use Issue Date October 2003 Page 1 of 1 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual CE OPERATING INSTRUCTION N319 TEST PARAMETERS ASPHALT INSTROTEK XPLORER 3500 1 START UP gt Press on and allow the nuclear gauge to complete the self test routine nm 2 UNITS When lt READY gt is displayed NETS RECALL gt Press MENU and the following is displayed UP DOWN or ENTER 02 A a z Z gt P repeatedly until the following is SET UNITS xd displayed UP DOWN or ENTER Units kg m3 P Press and the following is displayed UP DOWN 7 ENTER P Press DOWN to set the desired unit m Zz 3 m I O Z P Press and the display will return to lt READY gt lt m n 3 COUNT TIME TERT Cnt Time X min gt Press TIME and the following is displayed UP DOWN or ENTER Cnt Time 1 min gt Press DOWN to set the desired count time UP DOWN or ENTER Issue Date March 2013 Page 1 of 5 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N319 O Z P Press and the display will return to lt READY gt lt m n 4 DEPTH E DEPTH XX mm gt Press DEPTH the following is displ
34. in value go to 5 1 To change value go to 5 2 5 1 Retain the Value gt Press to retain the displayed value of MA The display will return to lt READY gt Go to 6 5 2 Change the Value gt Press TES to change the displayed value of MA EXIT Select And the following will be displayed E E dl 3 Voidless COUNT Select source of P Press and the following is displayed Marchal valle 1 Stored Value 2 New Value To enter a new value go to 5 3 To select a stored value go to 5 4 Issue Date March 2013 Page 4 of 9 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N301 5 3 Enter a New Value DEPTH Marshall XXXX kg m3 P Press and the following is displayed E N Press ENTER when completed gt Use the numbered keys to enter the required value to the nearest 1kg m START MA XXXX kg m3 P Press ENTER and the following is displayed Do you want to save this g play value for later use If the value is not to be saved NO CE Press ccr and the display will return to lt READY gt Go to 6 To save the displayed value an oai Select Marshall and the following is displayed Memory Cell 1 XX2 XX 3 XX4 XX P Press Ex ll m n Press the numbered key 1 2 3 or 4 to select a memory cell in which to store the value Marshall And the following will be displayed XX
35. itch off if the nuclear gauge is not required for further use Issue Date March 2013 Page 2 of 2 The State of Queensland Department of Transport and Main Roads 2013 EL y Nuclear Gauge Testing Manual je Queensland AS Government OPERATING INSTRUCTION N325 TEST PARAMETERS ASPHALT TROXLER 3450 1 SET UP gt Press and allow the nuclear gauge to complete the self test routine 2 UNITS When READY is displayed P Press SPECIAL Set Time Date To access the Gauge Setup menu Print Set Up Depth Indicator Set Beeper Level P Press JE Scroll through the menu using the arrow keys SEN UNITS in XXX and the following is displayed 1 PCF 2 kg m 3 g cm gt Press 2 and the following is displayed The display will return to the Gauge Setup menu P Press Issue Date March 2013 Page 1 of 8 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N325 3 COUNT TIME COUNT TIME XX 1 15 sec 2 1 min 3 4 min P Press TIME f and the following is displayed B et COUNT TIME gt Press 2 and the following is displayed The display will return to lt READY gt 4 ASPHALT MODE BE ey MODE gt Press and the following is displayed 1 Soil Mode 2 Asphalt Mode 3 Thin Layer Mode gt Press 2 And the following will be displayed briefly The display will return to lt READY
36. ll be displayed Input and press ENTER Use the numbered keys to enter the asphalt density bias to the nearest 0 001 g cm Issue Date October 2003 Page 5 of 7 The State of Queensland Department of Main Roads 2003 NuclearGauge Testing Manual Operating Instruction N307 Offset ENABLED gt Press SMARU and the following will be displayed XXXXg cm3 Do you want to save this value Note It is not necessary to save the displayed value to enable it If the value is not to be saved Press and the display will return to READY C CE To save the displayed value Enter permanent Memory location Press YES and the following will be displayed to save Offset EXIT R Use the numbered keys to enter the memory location Note Record the memory location and bias to facilitate subsequent retrieval of saved values Offset ENABLED Press START and the following will be x XX g cm3 ENTER displayed briefly Saved in memory Pop ipn location X The display will return to lt READY gt 6 2 2 2 Select a Stored Value Offset X Mu XX goma Press and the following will be displayed 1 to select 2 for next Issue Date October 2003 Page 6 of 7 The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N307 Press repeatedly until the required memory location and value is displayed Offset ENABLED Press and
37. m Press ENTER Issue Date October 2003 Page 3 of 3 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual OS Deparment Main Roads OPERATING INSTRUCTION N310 MEASUREMENT ASPHALT CPN MC3 1 Measurement Press START At the end of the counting period the following will be displayed XXXX TOX XX dry XXXX XXXX XXXX XXXX Record Dn wet as the wet density to the nearest 0 001 t m Pre March 1988 Nuclear Gauge Press STEP E simultaneously 4 ac AC Record Ct wet as the density count Press simultaneously to return to the density display 1 ac Issue Date October 2003 Pagel of 2 The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N310 Post March 1988 Nuclear Gauge Press STEP simultaneously y AC Press STEP Press ENTER repeatedly until Counts is displayed Press CLEAR Record Ct wet as the density count Press STEP simultaneously to return to the density display 1 y AC Press STEP Press ENTER repeatedly until Density is displayed Press CLEAR Issue Date October 2003 Page2 of 2 The State of Queensland Department of Main Roads 2003 Queensland Government Nuclear Gauge Testing Manual MEN OPERATING INSTRUCTION N311 TEST PARAMETERS ASPHALT CPN MC1DR M
38. nd record the wet density to the nearest 0 001 Um To convert from kg m to t m divide the displayed value by 1000 Turn the PWR TIME switch to OFF if the nuclear gauge is not required for further use Issue Date October 2003 Page 1 of 1 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual OS Deparimentot Main Roads OPERATING INSTRUCTION N307 TEST PARAMETERS TROXLER 4640B 1 Start up gt Press and allow the nuclear gauge to complete the self test routine 2 Measurement Units SPECIAL FUNCTION gt Press and the following Mos s de x will be displayed 2 7 Recover Erase mE Units in ZZZ Press and the following will be displayed Press 1 US 7 g play EJ 2 METRIC ENTER no change OFFSET Density in kg m3 OFFSET 2 z Press and the following will be displayed Select 1 kg m3 Enter no change UNITS METRIC Press and the following will be displayed Density in g cm3 Units of g cm are equivalent to t m The display will return to lt READY gt Issue Date October 2003 Pagel of 7 The State of Queensland Department of Main Roads 2003 NuclearGauge Testing Manual Operating Instruction N307 3 Count Time Count Time XX min Press and the following will be displayed Do you want ES to change 1 0 5 min Press and the following will be displayed 5 j De U
39. nd the following is displayed V repeatedly until the required test Pe pus depth is displayed i H Z P Press and the display will return to READY lt m n 5 ASPHALT MODE AND MAXIMUM DENSITY MA od ee ZZ XXXX T4 P Press PH and the following is displayed NT MA XXXX T4 gt Press V until MA is displayed To retain the displayed value go to 5 1 To change the displayed value go to 5 2 5 1 Retain the value gt Press OFF to retain the displayed value Zz ss The display will return to lt READY gt Go to 6 Issue Date March 2013 Page 2 of 6 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N303 5 2 Change the value gt Press to change the display value of MA The following will be displayed net A For each digit gt Press V repeatedly until the required number is displayed TART gt Press an to confirm each number The display will return to lt READY gt 6 ASPHALT DENSITY BIAS Press and the following is displayed gt Press ha until the following is gt Press and the following is displayed gt Press Issue Date March 2013 Page 3 of 6 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N303 The following will be displayed Dens Offset OFF OR Dens Offset ON Want to enable Want to disable To di
40. ng Manual Operating Instruction N301 gt Use the numbered keys to enter the required value to the nearest 1kg m START gt Press ENTER The following will be displayed The display will return to lt READY gt Issue Date March 2013 Page 9 of 9 The State of Queensland Department of Transport and Main Roads 2013 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual ay CERO OPERATING INSTRUCTION N302 MEASUREMENT ASPHALT TROXLER 3440 1 SET UP gt Press and allow the nuclear gauge to complete the self test routine 2 MEASUREMENT When READY is displayed START gt Press ENTER The following will be displayed Depth 0 mm Depth 0 mm MA XXX kg m3 MA XXX kg m3 Time XX sec WD Offset Time XX sec asphalt density asphalt density bias disabled bias enabled At the end of the counting period the following will be displayed MA XX X 96 96 MA XX X 96 WD XXXX kg m3 WD XXXX kg m3 M XX M XX WD Offset VOIDS XXX ENTER More Info asphalt density asphalt density bias disabled bias enabled Issue Date March 2013 Page 1 of 2 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N302 If more information is required START P Press ENTER M XX M XX And following will be displayed VOIDS XX Record WD as the w
41. nsity Offset DISABLED ENABLED Do you want to Do you want to ENABLE DISABLE To disable the material wet density bias go to 7 1 To enable the material wet density bias go to 7 2 7 1 Disable Material Wet Density Bias noce conan iat ihe YES to disable the density P Press density offset isto OR EXIT offset C CE remain disabled And the following will be displayed briefly The display will return to READY Issue Date March 2013 Page 7 of 9 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N301 72 Enable Material Wet Density Bias to confirm that the YES 1 NO CE P Press Minen e i O density offset 1s to EXIT y C CE remain enabled Wet Density The following will be displayed ma e following will be displayed XXXX kg m3 Want to change To retain the value go to 7 2 1 To change the value go to 7 2 2 7 2 1 Retain the Value NO CE gt Press Pk to retain the displayed value of Wet Density Offset The following will be displayed briefly The display will return to lt READY gt 7 2 2 Change the Value YES eee cf WD Offset gt Press and the following is displayed Select or i S45 2 P Press OR and the following WD Offset Press enter when completed Issue Date March 2013 Page 8 of 9 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testi
42. s displayed eae enable OR Density Offset ON Want to disable To disable the material wet density bias go to 6 1 To enable the material wet density bias got to 6 2 Issue Date March 2013 Page 3 of 5 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N319 6 1 Disable Material Wet Density Bias gt Press to disable the density offset OR gt Press ME to confirm that the density offset is to remain disabled The following will be displayed The display will return to lt READY gt 6 2 Enable Material Wet Density Bias gt Press to enable the density offset OR gt Press ME to confirm that the density offset is to remain enabled 3 D Off XXXX kg m The following will be displayed SISO ENTE To retain the displayed value go to 6 2 1 To change the displayed value go to 6 2 2 6 2 1 Retain the Value ON and the following will be m dies YES displayed Density Offset Enabled The display will return to cz READY 6 2 2 Change the Value gt Press for a positive value Issue Date March 2013 Page 4 of 5 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N319 OR gt Press for a negative value For each digit gt Press DOWN until the required number is displayed START gt Press ENTER to confirm each number
43. sable the asphalt density bias go to 6 1 To enable the asphalt density bias go to 6 2 6 Disable Asphalt Density Bias ore confirm that the P Press wo density offset isto OR remain disabled ON to disable the density YES offset The following will be displayed briefly The display will return to lt READY gt Go to 7 6 2 Enable Asphalt Density Bias ON todisable th OFF to confirm that the a E density offset is t YES density offset 9OR wo emain disabled gt Press D Off XXXX kg m And the following will be displayed N or ENTER To retain the display go to 6 2 1 To change the display go to 6 2 2 Issue Date March 2013 Page 4 of 6 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N303 6 2 1 Retain the Value START P Press ENTER The following will be displayed The display will return to lt READY gt Go to 7 6 2 2 Change the Value to enter a positive to enter a negative Press asphalt density bias OR asphalt density bias For each digit P Press until the required number is displayed START a P Press ENTER to confirm each number The following will be displayed briefly Dens Offset ON The display will return to lt READY gt 7 ASPHALT VOIDLESS DENSITY gt Press and the following is displayed M or ENTER repeatedly until the following is VOIDLESS DENS P Press display
44. t ENTER P Press START At the end of the counting period the display will return to lt READY gt Turn the power switch off if the nuclear gauge is not required for further use Issue Date March 2013 Page 8 of 8 The State of Queensland Department of Transport and Main Roads 2013 Queensland Government MEN y Nuclear Gauge Testing Manual ay CLTN OPERATING INSTRUCTION N324 MEASUREMENT ASPHALT TROXLER 3430P 1 START UP Turn the power switch on and allow the nuclear gauge to complete the self test routine 2 MEASUREMENT When READY is displayed Depth XX mm PR XXXX kg m3 gt Press ENTER the following is displayed Time XX sec In the manual depth mode the gauge will prompt for the source rod depth In automatic mode the gauge software reads the depth strip on the source rod to determine the depth At the end of the counting period the following will be WD xxxx displayed M x M X X Record WD as the wet density P Press ESC gt Press RECALL gt Press V DC 2 xxxx The following will be displayed Issue Date March 2013 Page 1 of 2 The State of Queensland Department of Transport and Main Roads 2013 Nuclear Gauge Testing Manual Operating Instruction N324 Record the following values as appropriate DC as the density count MC as the moisture count P Press ESC and the display will return to lt READY gt p Turn the power sw
45. the following will XX g cm3 be displayed briefly The display will return to lt READY gt gt Press OFF if the nuclear gauge is not required for further use Issue Date October 2003 Page 7 of 7 The State of Queensland Department of Main Roads 2003 THIS PAGE IS INTENTIONALLY BLANK Queensland Government Nuclear Gauge Testing Manual M Deparment Main Roads OPERATING INSTRUCTION N308 MEASUREMENT ASPHALT TROXLER 4640B 1 Start up Press and allow the nuclear gauge to complete the self test routine 2 Measurement When READY is displayed START Press ENTER MA XXXX g cm3 MA XXXX g cm3 Thick XX XX cm Thick XX XX cm The following will be Avg XX Avg XX Offset displayed Time XX secs Time XX secs asphalt density asphalt density bias disabled bias enabled Dens XXXX kg m3 At the end of the counting period the following will be E i 2 displayed 100 MA XXX XX 9eVOID X XX Record Dens as the wet density to the nearest 0 001 tm Dens XXX X kg m3 RECALL i s i VOID X XX 0 will be displayed Cnts XXXX XXXX Record Cnts as the density count values for System 1 and System 2 Issue Date October 2003 Pagel of 2 The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N308 Press and the display will return to READY C CE Press OFF if the nuclear gauge is not required for f
46. urther use Issue Date October 2003 Page 2 of 2 The State of Queensland Department of Main Roads 2003 Queensland Government Nuclear Gauge Testing Manual OS Deparimentot Main Roads OPERATING INSTRUCTION N309 TEST PARAMETERS ASPHALT CPN MC3 1 Measurement Units Pre March 1998 Nuclear Gauge gt Press simultaneously until the density and moisture display is lac obtained UNIT 1 ac Press until gee is displayed Post March 1998 Nuclear Gauge um Press STEP simultaneously 1 AC Press ENTER until gee is displayed Press STEP Press ENTER until Density is displayed Press CLEAR Issue Date October 2003 Page 1 of 3 O The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N309 2 Count Time T i gt Press ENTER 3 Maximum Density COMP Press E until Md is displayed Press EN and use the numbered keys to enter 0 0 4 4 Asphalt Density Bias D BIAS Press al w To enter a positive bias gt Press ES and use the numbered keys to enter the asphalt density bias to the nearest 0 001 t m Issue Date October 2003 Page2 of 3 The State of Queensland Department of Main Roads 2003 Nuclear Gauge Testing Manual Operating Instruction N309 P Press ENTER To enter a negative bias Press and use the numbered keys to enter the asphalt density bias to the nearest 0 001 t
Download Pdf Manuals
Related Search
Related Contents
safety instructions Mise en page 1 - Drouot Formation Scarica le istruzioni - Foto Copyright © All rights reserved.
Failed to retrieve file