Miele Cooktop KM2012G Manual
Contents
1. Main burner jet Small burner jet NG Small burner 0 90 0 52 Medium burner 1 18 0 52 Large burner Wok 1 75 1 10 ULPG Small burner 0 53 0 32 Medium burner 0 70 0 42 Large burner Wok 1 00 0 65 The jet markings refer to 1 100 mm of the jet diameter 38 Conversion to another type of gas Changing the jets Small medium and large burners Disconnect the gas cooktop from the electricity supply by switching off at the socket or by disconnecting the mains fuse To change the main jet m Take off the burner cap burner ring CD for the wok and burner head m Using an M7 socket spanner unscrew the main jet 8 m Fit the correct jets securely see jet table Wok burner 39 Conversion to another type of gas To change the small jet for all burners The top of the appliance has to be removed before the small jets can be changed m Loosen the fixing screws on the burners m Pull the control knobs off m Lift the top of the appliance off m Remove the ignition switch CD m Using a small screwdriver unscrew small jet in the gas fitting m Pull out the jet with a pair of pliers m Fit the correct jets securely see jet table 40 Conversion to another type of gas After changing the jets m Reassemble the burner parts in the reverse order m Check all gas fittings for leaks by operating the burner without the top section of the c2. Adelaide 83 85 Sir Donald Bradman Drive Hilton SA 5033 Telephone 1800 018 770 Fax 1800 799 578 Perth 205 207 Stirling Highway Claremont WA 6010 Telephone 1800 094 872 Fax 1800 799 578 www miele com au Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland New Zealand Telephone 0800 264 353 Fax 0800 463 453 www miele co nz Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Alteration rights reserved 2311 CE M Nr 07 143 630 01
3. in use and remains hot for quite a while after being switched off Do not touch it whilst it could still be hot P When using a rangehood above the cooktop ensure that the burner is always covered with a pan when in use Otherwise flames could be drawn up by the suction of the rangehood parts of which could then be damaged or even set on fire P Do not leave the cooktop unattended whilst it is being used Boiling fat or oil could ignite and cause a fire P If oil or fat does catch fire do not attempt to put out the flames with water Use a suitable fire blanket saucepan lid damp towel or similar to smother the flames P Do not use the cooktop to heat up the room Due to the high temperatures radiated objects near the appliance could catch fire P For added protection it is advisable to use heat resistant pot holders or gloves when using the appliance Ensure that they do not come into contact with the flames Do not use large cloths tea towels or similar as the ends could touch the flames and catch fire Take care not to let these items get damp or wet as this causes heat to transfer through the material more quickly with the risk of scalding or burning yourself 12 P Do not flamb under a rangehood The flames could set the rangehood on fire P Do not use the appliance as a resting place for anything else The article could melt or catch fire if residual heat is still present or if the appl
4. indicate a faulty connection or appliance Operation Switching on 16 The control is used to ignite the burner and to regulate the strength of the flame eThe gas supply is turned off Strong flame Weak flame The burners can only be switched on by pressing in the appropriate control and turning it anti clockwise and switched off by turning the control clockwise The following will cause damage to the appliance Switching on the burner without pressing the control down Switching the burner on by turning the control clockwise Switching the burner off by turning the control anti clockwise The manufacturer will not accept liability for any damage resulting from incorrect operation Do not leave the appliance unattended whilst it is being used m he control for the burner required must be pressed in and turned anti clockwise to the large flame symbol to switch on A spark is automatically produced on all burners when a control knob is activated This is completely normal and does not indicate a fault with the appliance m When the flame ignites keep the control pressed in for 8 10 seconds and then let it go m f the flame goes out turn the control to e and wait for at least 1 minute before trying to ignite it again If necessary keep the control pressed in for longer m f the burner does not ignite after a second attempt turn the control back to e and go to the Problem solvi
5. removed in countries where this is applicable itis switched off at the wall socket and the plug is withdrawn from the socket or it is switched off at the isolator P While the appliance is under warranty repairs should only be undertaken by a service technician authorised by Miele Otherwise the manufacturer s warranty will be invalidated P Faulty components must only be replaced by genuine Miele original spare parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used P If the connection cable is damaged it must be replaced by a suitably qualified electrician with a specialist connection cable of type H 05 VV F pvc insulated available from Miele P Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating P Do not use the gas cooktop if it is faulty Switch it off immediately disconnect it from the mains electricity and the gas supply and call Miele P In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage caused by cockroaches or other vermin will not be covered by the warranty Warning and Safety instructions Correct use P The appliance gets hot when
6. wrung out cloth Do not let the ignitor get wet If it gets wet it will not spark 22 Cleaning and care To assemble the small medium and large burners m Place the burner head 9 onto the burner base so the ignition safety device the ignitor and the retaining pins fit into their respective holes in the burner head m Position the burner cap 2 onto the burner head so that the retaining pins fit into their respective recesses Gently twist the burner cap clockwise or anticlockwise until it locks into position When correctly positioned it will not slide about Important replace parts in the correct order after cleaning 23 Cleaning and care To assemble the wok burner m Place burner head 3 onto burner base 9 so that the ignition safety device and the ignitor extend through their respective holes in the burner head m Replace the burner ring m Replace the burner cap Q2 Important replace parts in the correct order after cleaning 24 Problem solving guide What to do if Repairs to the gas and electrical components of this appliance must only be carried out by a suitably qualified and competent person to ensure safety Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work the burner does not ignite after several attempts Check whether the burner is correctly assemb
7. ING THIS APPLIANCE MUST BE EARTHED 34 Important The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol amp or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter A or coloured red Gas connection Connection to the gas supply or conversion from one type of gas to another should only be undertaken by an approved gas fitter who is responsible for correct functioning of the appliance when installed Every appliance should have its own isolating valve The gas connection must be installed so that connection can be made either from inside or outside the kitchen unit and the isolating valve must be easily accessible and visible by opening one of the kitchen unit doors if necessary Check with your local gas supplier about the type of gas and its calorific value and compare this information with the type of
8. Miele Operating instructions RT BEN Gas cooktops KM 2012 To avoid the risk of accidents en AU NZ or damage to the appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 143 630 US N2 This appliance can be used in countries other than those specified on the appliance It is however set up for connection to the gas and electricity supplies in the countries specified For use in other countries please contact the Miele spare parts or customer service department in your country Contents Guide to the appliance 5 OOKIDD eerte meets at aires sig gy ete gr eases i ee 5 B ttlerS ox sese RE eee pated np He gad vont ae arg ba de d qu AE 6 Accessories supplied i tasse gb teed bene Phew o eb blo a e bad 7 Warning and Safety instructions 8 Caring for the environment 14 Before using for the first time 15 Operation 222446255 ke RETI AXE RSEN qi eee Wd 16 SWIHCHIMNGMON Jute rng ge out S OT MON E Robe Us e dio a pou ae odi 16 Regulating the flame x coxa ve eque x exe Ree US Roe e ER CERE ded 17 SWIICHINGLOM RE de Rm e unda dein 17 Suitable pans 18 WOK TING idk 44 bb dd tei end thd teh Foe loe been be 19 Safety cut out lisi issu
9. able on the pan support If the pan diameter is too large flames can spread out to the sides and damage or burn the worktop wall claddings or surrounding units and also parts of the cooktop The manufacturer cannot be held liable for this type of damage Wide shallow pans are preferable to tall narrow ones They will heat up faster Select pans which are suitable for the burner they are to be used on In general use larger diameter pans on the large burners and smaller diameter pans on the small burners Pans with thick bases are preferable as these distribute heat more evenly With thin bases there is a danger of food overheating in places Stir the food frequently Any heat resistant pans can be used on a gas burner Suitable pans Always place the pan on the pan support supplied with the cooktop Do not place a pan directly on top of the burner Remember when purchasing new pans that manufacturers usually refer to the diameter at the top of the pan in their documentation Use a lid whenever possible to minimise heat loss When using a wok make sure that the base does not touch the burner A distance of 1 cm should be maintained between the burner and the base of the wok pan above it Place pans flat on the pan support to ensure they do not tip over Slight tilting cannot always be avoided Wok ring C 24 Use the wok ring supplied to give additional sta
10. age is at the owner s risk and could be dangerous The manufacturer cannot be held liable for damage resulting from incorrect or improper use or operation P The appliance is not suitable for outdoor use P This gas cooktop is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they are supervised whilst using it or have been given instruction concerning its use by a person responsible for their safety Warning and Safety instructions Safety with children P This appliance is only intended for use by adults who have read these instructions This appliance is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or to use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen P Older children may use the appliance only when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse P The appliance gets hot when in use and remains hot for quite a while after being switched off To safeguard against burning keep children well away from the appliance at all times P Do not store anything which might arouse a child s interest in storage areas above or next to the appliance Otherwise they could be tempted into climbing
11. bility N especially to woks with a rounded base Safety cut out 20 This appliance is fitted with a thermoelectric ignition safety device which cuts off the supply of gas to a burner if the flame goes out for example if food has boiled over or if there was a sudden draught m Touse the burner again turn the control clockwise to the e position and then switch it back on as normal The safety cut out operates independently from the electricity supply This means that it will still work if the cooktop is used during a power cut Cleaning and care Do not use a steam cleaning appliance to clean this appliance The steam could reach the electrical components and cause a short circuit The appliance should be cleaned regularly preferably after each use Allow the appliance to cool down to a safe temperature before cleaning To avoid water marks and limescale deposits use a soft cloth to dry surfaces that have been cleaned with water Stubborn soiling should be soaked first Food that has boiled over can cause discolouration of the burner parts and the stainless steel cooktop Remove any soiling immediately The surfaces of the two burner caps will become more matt with time This is quite normal and will not affect the operation of the cooktop To avoid damaging the outer surfaces of your appliance do not use cleaning agents containing soda alkalines ammonia acids or chlorides cl
12. e appliance storage drawer or near the appliance P Do not spray aerosols in the vicinity of this appliance while it is in operation gt Remove splashes of fat and other food debris from the surface as soon as possible These are a fire hazard P Replace the pan supports carefully to avoid scratching the surface of the cooktop P Using the gas cooktop will cause a build up of heat and moisture in the room in which it is installed Ensure that the room has sufficient natural or mechanical means of ventilation e g a rangehood gt If the cooktop is used for very long periods of time additional ventilation of the room may be necessary e g by opening windows or doors or running the rangehood on the highest setting P When using an electrical appliance e g a hand held mixer near the gas cooktop ensure that the connection cable doesn t come into contact with the hot cooktop The insulation on the cable could become damaged giving rise to an electric shock hazard P Always ensure that food is sufficiently cooked or reheated Some foods may contain micro organisms which are only destroyed by thorough cooking at a sufficiently high temperature for long enough Therefore when cooking or reheating food such as poultry it is particularly important that the food is completely cooked through If in doubt select a longer cooking or reheating time P Do not use pans that are large enough to cover more than o
13. eaning agents containing descaling agents stain or rust removers abrasive cleaning agents e g powder cleaners and cream eaners O solvent based cleaning agents dishwasher cleaner g rill and oven cleaners glass cleaning agents hard abrasive brushes or sponges e g pot scourers brushes or sponges which have been previously used with abrasive cleaning agents sharp pointed objects these can damage the seal between the frame and the worktop 21 Cleaning and care Cleaning Notes Stainless steel Clean stainless steel surfaces using an Original Printed surfaces surfaces Miele all purpose microfibre cloth or with a Flame symbols solution of warm water and a little washing up liquid applied with a soft sponge The printing can be damaged If required clean the appliance with the rough if soiling e g food or fluids side of a sponge and a few drops of the Original that contained salt olive oil Miele ceramic and stainless steel cooktop are not removed immediately cleaner see Optional accessories Remove any soiling immedi Apply with an even pressure following the ately direction of the grain Do not use any stainless steel The Original Miele care product for stainless cleaner on printed surfaces steel can be used after cleaning to help keep This would rub off the print your appliance looking good see Optional accessories Apply sparingly with a soft cloth following the in
14. eater clearance of the two Side rear clearances to the cooktop Ideally the cooktop should be installed with plenty of space on either side There may be a wall at the rear anda tall unit or wall at one side On the other side however no unit or divider should stand higher than the cooktop see illustrations Not recommended 29 Safety clearances Before installing the appliance check that the location provides the required clearances from combustible material and if necessary provide protection to adjacent surfaces as required by regulations The minimum side clearance from a cooktop to a combustible surface shall be a 300 mm horizontal distance from the periphery of any burner The minimum rear clearance from a cooktop to a combustible surface shall be a 200 mm horizontal distance from the periphery of any gas burner AS 5601 non combustible surface or splashback shall be a 50 mm horizontal distance from the rear edge of the cooktop 30 If the clearance between the periphery of any gas burner and the side wall is less than 300 mm the rear wall is less than 200 mm the walls must be protected with a non combustible material The protection must be extended a minimum distance of 150 mm above the burner refer gas fitting regulations Shown area indicates protected surface which may be ceramic tiles or other approved material Combustible surface The surface
15. gas quoted on the cooktop data plate This appliance is set up for connection to natural gas See adhesive label on the appliance G NG natural gas LP ULPG Propane Butane Jets are supplied for conversion to ULPG Propane Butane gas If the appropriate jets have not been supplied with the appliance you will need to contact your Chartered Agent or Miele Conversion to another type of gas is described under the relevant Section 35 Gas connection The gas connection must be in accordance with national and local regulations The relevant building regulations must also be observed Natural gas liquid gas During installation the gas connection must be positioned so that it is not adversely heated when the appliance is in operation Pressure Test Point D This is provided on the gas regulator supplied for natural gas m Loosen the screw in the test point until it is free in its housing The screw is retained in this position m Connect the hose from the pressure gauge m Reassemble one of the large burners turn on the gas and manually light the burners 36 Gas pressure must be set by the approved gas fitter as shown on the data plate Natural gas 1 0 kPa ULPG Propane Butane 2 75 kPa m Disconnect gauge and screw in the test point screw The Gas Regulator must be set with the largest burner operating at maximum setting Once the gas cooktop has been installed it is essentia
16. iance is switched on by mistake P Do not cover the appliance e g with a cloth kitchen foil etc This could be a fire hazard if the appliance is switched on by mistake P Do not use plastic or aluminium foil containers These melt at high temperatures and could catch fire P Do not heat up unopened tins of food on the cooktop as pressure will build up in the tin causing it to explode This could result in injury and scalding or damage to the cooktop P Make sure all the components of the gas burners have been correctly assembled before switching on P Pans must be the correct size for the burner they are used on see Pans A pan which is too small will be unstable on the pan support If the pan diameter is too large flames can spread out to the sides and damage or burn the worktop wall claddings or surrounding units and also parts of the cooktop Miele will not accept liability for any damage resulting from such incorrect use P Ensure that the flames from the burner do not spread out beyond the base and up the sides of the pan Warning and Safety instructions P Unless the pan manufacturer states that you can do so do not use pans with very thin bases on this cooktop and never heat up empty pans as they could get damaged This could also damage the appliance P Always use the pan support supplied Never place a pan on the burner itself P Do not use or store flammable materials in th
17. ician if in any doubt 10 D The connection to the gas supply must be carried out by a suitably qualified and competent person in accordance with current local and national safety regulations If the appliance is supplied without a plug or if the plug is removed it must be connected to the mains electricity supply by a suitably qualified and competent electrician in strict accordance with current local and national safety regulations The manufacturer cannot be held liable for damage caused by incorrect installation or connection D For safety reasons this appliance may only be used when it has been built in P Never open the housing of the appliance Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults P Installation maintenance and repairs may only be carried out by a Miele authorised suitably qualified and competent person in strict accordance with current national and local safety regulations Repairs and other work by unauthorised and unqualified persons could be dangerous Miele cannot be held liable for unauthorised work Warning and Safety instructions gt The gas cooktop must be disconnected from the gas supply and mains electricity before repairs and maintenance work is carried out It is only completely isolated from the electricity supply when the mains fuse is disconnected the screw out fuse is
18. ium and large burners Burner ring 2 Burner cap 8 Burner head a Burner base Ignition safety device Ignitor Guide to the appliance Accessories supplied The accessories supplied with your appliance as well as a range of optional ones are available to order from Miele see Optional accessories Wok ring The wok ring supplied gives additional stability to the wok especially to woks with a rounded base gt Warning and Safety instructions This appliance complies with all relevant local and national safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important notes on installation safety use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the contents Pass them on to any future owner Do not modify this appliance Correct application P This appliance is designed for domestic use and for use in similar environments by guests in hotel or motel rooms bed amp breakfasts and other typical living quarters This does not include common shared facilities or commercial facilities within hotels motels or bed amp breakfasts P This gas cooktop must only be used as described in these instructions Any other us
19. l to check that neither the gas pipe nor the electricity cable is in contact with hot parts of the appliance or hot gas exhaust This gas cooktop can be connected with a class B or D flexible hose which complies with AS NZS 1869 and must be certified The min inner must be 10 mm and the maximum length 1 2 m Make sure it does not touch moving parts of the kitchen furniture e g a drawer A full operational test and a test for possible leakages must be carried out by the fitter after installation Burner ratings Nominal ratings for all gas types with the burner full on Gas type KM 2012 MJ h Small burner NG 4 1 ULPG 3 6 Medium burner NG 7 0 ULPG 6 5 Large burner NG ULPG Wok NG 14 5 ULPG 12 5 Total NG 32 6 ULPG 29 1 Nominal rating at low setting Gas type KM 2012 MJ h Small burner NG 1 14 ULPG 1 02 Medium burner NG 1 64 ULPG 1 93 Large burner NG ULPG Wok NG 5 00 ULPG 4 53 Nominal ratings for ULPG are based on propane gas 37 Conversion to another type of gas N Connection to the gas supply or conversion from one type of gas to another should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations Jet table When converting to a different type of gas the main burner jet and the small burner jets have to be changed
20. led the gas supply tap is turned on the burner is dry and clean the flame slits are dry and unblocked the gas flame goes out after being lit During the ignition process the flames need to touch the ignition safety device so that it heats up If the flames do not touch the ignition safety device check if the burner cover is correctly in position there is no soiling on the ignition safety device If there is remove it carefully see Cleaning and care 25 Problem solving guide the ignitor on the burner does not spark Check whether the mains fuse has blown If it has contact a qualified electrician or Miele food deposits have lodged themselves between the ignitor and the burner cap or on the ignition safety device Remove any food deposits carefully see Cleaning and care food has adhered to the ignition safety device Remove any food deposits carefully see Cleaning and care the flame suddenly looks different Check that the burner is correctly assembled 26 Optional accessories Miele offers a range of useful accessories as well as cleaning and conditioning products for your appliance These can be ordered via the internet at www miele shop com depending on country Miele www miele shop com These products can also be obtained from Miele see back cover for contact details or from your Miele Chartered Agent Cleaning p
21. ne burner The resulting build up of heat could damage the appliance P Avoid allowing liquids or foods containing salt to spill onto the cooktop If salty foods or liquids do get on the cooktop they should be removed as soon as possible to avoid the risk of corrosion P If the cooktop is built in behind a furniture door it must only be operated when the door is open Close the furniture door only once the appliance has been switched off and the residual heat indicators have gone out P If the appliance has not been used for a long period of time it should be thoroughly cleaned before it is used again It is also advisable to have the appliance tested by a qualified person for safety Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Rather than just throwing these materials away please ensure they are offered for recycling 14 Disposal of your old appliance or machine Electrical and electronic appliances machines often contain materials which if handled or disposed of incorrectly co
22. ng guide for advice Operation In the event of a power cut If there is an interruption to the electricity supply the gas can be ignited with a match m Press in the relevant control and turn it anti clockwise to the large gas symbol m Hold the control pressed in and light the gas at the burner with a match m Keep the control pressed in for a further 8 10 seconds and then release it Regulating the flame The burners can be regulated at any level between the strongest and weakest flame Control the flame so that it does not spread out beyond the sides of the pan As the outer part of the flame is much hotter at Titan the centre the tips of the flames should stay beneath the Switching off pan base Flame tips which extend beyond the sides of the pan merely warm up the air in the room and can also damage pan handles and increase the danger of injury m Turn the control clockwise to position e This stops the flow of gas and the flame goes out Suitable pans rae 18 Burner Min pan base diameter in cm Small burner 10 Medium burner 12 Large burner 14 Wok burner 14 Max diameter at top of pan in cm Small burner 22 Medium burner 22 Large burner 24 Wok burner 24 Refer to the chart above and ensure that the pan diameter falls within the minimum and maximum diameters given for the burner you are using A pan base which is too small will be unst
23. of a material that is capable of catching fire and burning at temperatures exceeding 50 K above ambient Appliance and building in dimensions KM 2012 QD Front 2 Building in depth 3 Gas connection R 1 2 ISO 7 1 Mains connection box with mains connection cable L 2 000 mm 31 Installation Preparing the worktop Installing the cooktop m Make the worktop cut out following the dimensions applicable Remember to maintain a minimum safety clearance from the back wall as well as from any tall unit or side wall to the right or left of the cooktop See Safety clearances m Seal the cut surfaces with a suitable heat resistant sealant to avoid swelling caused by moisture If during installation you find that the seals on the corners of the frame are not flush with the worktop surface the corner radius x R4 can be carefully scribed to fit m Place the cooktop in the cut out without securing it m Feed the connection cable down through the cut out m Connect the cooktop to the mains see Electrical connection m Connect the appliance to the gas supply see Gas connection m Secure the appliance using the brackets supplied 32 General installation tips Sealant Do not use any sealant unless expressly instructed to do so The sealing strip under the edge of the top part of the cooktop
24. onto the appliance with the risk of burning themselves gt Keep all pans out of reach of children Turn pan handles inwards away from the edge of the cooktop Danger of burning or scalding Special cooktop guards are available from good retail outlets P Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Dispose of or recycle all packaging safely as soon as possible Warning and Safety instructions Technical safety P Before installation check the appliance for visible signs of damage Do not install and use a damaged appliance A damaged appliance is dangerous P The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock P Before connecting the appliance to the mains supply make sure that the voltage and frequency details given on the data plate correspond to the on site electricity supply otherwise the appliance could be damaged Consult a qualified electr
25. ooktop in place use a match to ignite the flame m Remove the loose burner parts again m Replace the top section of the cooktop m Screw the parts for the burner bases together securely and assemble the burners in the correct order m Replace the control knobs m Ignite all the burners to check that they are operating correctly The flame must not go out on the lowest setting or when the control is turned quickly from a high to a low setting On the highest setting the flame must have a distinctive and visible core m Adhere the label supplied with the jets above the label stating the type of gas being used 41 After sales service data plate The address and phone number of your nearest Miele office is given on the back page The voltage and rated load are given on the data plate Please quote this data together with the model description and serial number when contacting Miele Space in which to adhere the extra data plate supplied with the appliance Ensure that the model number is the same as the one on the front of these operating instructions 42 43 Miele Australia Pty Ltd ABN 96 005 635 398 Melbourne 1 Gilbert Park Drive Knoxfield VIC 3180 Telephone 03 9764 7130 Fax 03 9764 7149 Sydney 3 Skyline Place Frenchs Forest NSW 2086 Telephone 02 8977 4230 Fax 02 8977 4249 Brisbane 39 Harvey Street North Eagle Farm QLD 4009 Telephone 1800 798 578 Fax 1800 799 578
26. provides a sufficient seal for the worktop Do not use sealant between the frame of the top part of the cooktop and the worktop This could cause difficulties if the cooktop ever needs to be taken out for servicing and possibly result in damage to the frame or the worktop Tiled worktop The grouting and the shaded area underneath the cooktop frame must be smooth and even so that the frame sits evenly and the sealing strip underneath the top part of the cooktop provides a sufficient seal for the worktop Tiled worktops must be a minimum 5 mm thick to ensure the surface temperatures of the combustible surfaces underneath the tiles do not exceed 50 K above ambient 33 Electrical connection All electrical work should be carried out by a suitably qualified and competent person in strict accordance with national and local safety regulations If the connection cable is damaged it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V F pvc insulated available from Miele For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA Connection for each appliance should be made via a suitable isolator Note Isolation of the appliance is required when the appliance safety device is activated Ensure the isolating Switch is easily accessible and visible The data plate gives the necessary data for connection WARN
27. roducts Original Miele ceramic and stainless steel cooktop cleaner 250 ml Removes heavy soiling limescale deposits and light discolouration 250 ml Removes water marks flecks and finger prints Helps keep the appliance looking good for longer Original Miele all purpose microfibre cloth Removes finger marks and light soiling 27 Safety instructions for installation Fit the wall units and rangehood before fitting the cooktop to avoid damaging the surface P This appliance must not be connected to a gas flue It must be installed and connected in accordance with current installation regulations D The room in which the gas cooktop is installed must be at least 20 m in size with a door or window in it which can be opened to the outside air D The veneer or laminate coatings of worktops or adjacent kitchen units must be treated with 100 C heat resistant adhesive which will not dissolve or distort Any backmoulds must be of heat resistant material P An electric fryer must not be installed directly next to a gas cooktop as the gas flames could ignite the fat in the fryer It is essential to maintain a distance of at least 300 mm between these two appliances P A gas cooktop may not be built in over a fridge fridge freezer freezer dishwasher washing machine or tumble dryer P This appliance must not be installed and used in mobile installations such as ships etc 28 P En
28. s due eee deua Rap ped RR unes 20 Cleaning and care 21 Problem solving guide 25 Optional accessories 27 Safety instructions for installation 28 Safety clearances 29 Appliance and building in dimensions 31 Installation i 4 44 ree on asada dee ERR ea 32 General installation tips 33 Contents Electrical connection 34 Gas connection 35 Burner ratings 37 Conversion to another type of gas 38 cs PPP 38 Changing the Jets ser cei we queque ne man Een Lege hd book ded 39 To change the main jet 2 en ea EORR RR RECIPE er dona 39 To change the small jet liiis 40 After changing the jets 41 After sales service data plate 42 Guide to the appliance Cooktop Wok burner Controls Small burner 8 Front right 839 Medium burners Rear right Rear left Front left Guide to the appliance Burners Wok burner Small med
29. structions on the packaging Pan support Remove the cover These areas should only be Stubborn soiling should be cleaned with a microfibre cloth or with a solution of warm water and a little washing up liquid applied with a soft sponge If necessary the reverse side of a non scratching washing up sponge can be used soaked first Not dishwasher safe Control knob Control knobs should only be cleaned with a microfibre cloth or with a solution of warm water and a little washing up liquid applied with a soft sponge Not dishwasher safe Burner caps Burner caps should only be cleaned with a microfibre cloth or with a solution of warm water and a little washing up liquid applied with a soft sponge If necessary the reverse side of a non scratching washing up sponge can be used Not dishwasher safe Burner head PerfectClean Burner heads should only be cleaned with a microfibre cloth or with a solution of warm water and a little washing up liquid applied with a soft sponge If necessary the reverse side of a non scratching washing up sponge can be used The surface of the burner heads is treated with PerfectClean enamel which has very good anti stick properties and is easy to clean Not dishwasher safe Make sure that the flame slits are clean and completely dry Ignitor Ignition safety device The ignitor and ignition safety device should be very carefully wiped clean using a well
30. sure that the gas pipe and electrical cable are installed in such a way that they do not touch any parts of the appliance which become hot This could cause damage gt The electrical cable and a flexible gas connection pipe must be installed in such a way so that they do not come into contact with any moving kitchen parts e g a drawer and cannot become trapped P Observe carefully the safety distances given on the following pages All dimensions in this instruction booklet are given in mm N This appliance must be installed and connected to services in accordance with local and national safety and building regulations Safety clearances Safety clearance above the cooktop A minimum safety clearance must be maintained between the cooktop and the rangehood above it See the rangehood manufacturer s operating and installation instructions for details If the manufacturer s instructions are not available for the rangehood a minimum safety clearance of at least 760 mm above the burner cap must be maintained For any flammable objects e g utensil rails wall units etc a minimum clearance of at least 760 mm above the burner cap must be maintained between them and the cooktop below When two or more appliances are installed together below a rangehood e g a gas cooktop and an induction cooktop combiset which have different safety clearances given in the installation instructions you should select the gr
31. uld be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance or machine Therefore please do not dispose of your old machine or appliance with your household waste Please dispose of it at your local community waste collection recycling centre and ensure that it presents no danger to children while being stored for disposal It should be unplugged from the mains electricity supply and disconnected from the gas supply by a competent person The plug must be rendered useless and the cable cut off directly behind the appliance or the machine to prevent misuse Before using for the first time Please adhere the extra data plate for the appliance supplied with this documentation in the space provided in the After sales service section of this booklet Cleaning for the first time m Remove any protective foil and adhesive labels m Clean all removable parts of the burners with a solution of warm water and a small amount of washing up liquid applied with a soft sponge Dry all parts thoroughly after cleaning and then reassemble the burners see Cleaning and care Burners m Clean the stainless steel cooktop with a damp cloth and then wipe dry The metal components have a protective coating which may give off a slight smell when heated up for the first time The smell and any vapours will dissipate after a short time and do not
Download Pdf Manuals
Related Search