TIM-01 Installation Manual
Contents
1. Trig terminal Trigger applied singularly not simultaneously Timer is activated by application of trigger not by removal of trigger i e When using Stand off Timer mode for DOTL change over reed Desig n ed amp Ma n ufa ctu red switches N O when door closed must be used or a relay used to invert reed switch operation2. gh k F ma Bas ah ig 7 7 z E j regal im CEO Oa eS So yy SG 7 spu fl IRGA Mo ia DH H See over page for details Power LED SW 4 Ones Switch Bank SW 3 Tens Switch Bank SW 2 Timing Switch Bank Relay Operation LED SW 1 Mode Switch Bank Output Relay 1A 30Vdc Max SPDT Terminal Block SW 1 Mode One Shot DO 09 TIM 01 Program Modes TIM 01 Terminal Connections One Shot Applying trigger activates relay for selected time Trigger input must be removed amp re applied to re activate z gt g O N Retriggerable O N Strobe Retriggerable As for One Shot except where input is retriggered the timer starts again O 5 Clutch Relay Programmed Pulse O N Debounce Stand Off Timer Strobe Requires momentary trigger to be applied relay will activate for F All programmed time 124 By 12V 12Vdc Positive Input Clutch Relay Applying trigger causes relay to change state Removing O N Relay Fail Secure Normally Open Relay Contact h a s sfels s gt o lolololo lo o RN RIS R S R 5 3 Seconds Programmed Pulse Applying trigger causes relay to operate for Siete one second at programmed intervals Set intervals on SW2 SW3 amp SW4 OV 12V negative Operation ceases when trigger is removed Trig Positive Trigger Input mer Eee Debounce Applying trigger causes relay
3. to activate for programmed time Relay remains activated until timeout regardless of trigger being removed If input remains triggered after timeout relay remains activated Specifications until trigger is removed Stand Off Timer Ideal for DOTL Door Open Too Long alarms Timing Input Voltage 12Vdc 13 8Vdc commences when trigger is applied If trigger is removed before timeout Quiescent Current 15mA 12Vdc relay will not activate If trigger remains after timeout relay will activate See also Note 3 below Operational Current 35mA 12Vdc Relay Rating 1A 30Vdc SPDT Fail Secure The relay does not change state during power failure 851 x 54W x 20H mm Fail Safe The relay is energised when the trigger is not active Relay will Weight de energise e g releasing power to door locks during a power failure N 645 to Class B Important Information Common Relay Contact Relay Fail Safe i E ae ial y a ee trigger forces relay to change state No timing function in 12Vdc Negative Input Normally Closed Relay SW 2 Timing Contact 1 Power 12Vdc must be applied constantly to the timer i e Power cannot be applied simultaneously with trigger TIM 01 may be programmed while powered but power must be disconnected for 10 seconds then re applied before new programming options are initialised TIM 01 may be triggered by the application of OV 12V negative to the Trig terminal or by the application of 5 12Vdc max to the
4. Tactical Technologies Australia s Premier Security Power Specialist High Quality Security Products Designed Manufactured and Supported in Australia www tac tech com au 5 Butterfield St Blacktown NSW 2148 Australia 61 2 8822 1888 Tel 61 2 8822 1899 Fax TACTICAL TECHNOLOGIES Universal Digital Timer Module TIM O1 TIM 01 General Features The TIM O1 Universal Digital Timer Module has been designed to provide 8 held programmable functions controlling a Single Pole Double Throw relay with timing intervals ranging between 1 second and 99 days The unit must be powered by a constant 12Vdc power supply and will accept either positive or negative triggering from external devices such as reed switches request to exit buttons and access control PLC s Programmable Logic Controllers TIM O1 may be programmed for Fail Safe operation relay is energised when trigger is not active amp will de energise during power failure or Fail Secure relay does not change state during a power failure Programming may be changed whilst unit is powered but power must be disconnected then reconnected before changes become active as DIP switch configuration is read during boot sequence only TIM 01 Layout pr B y S m Han fn a p DE UT OE i aanktada es E C im 5 iy i ee ao a a a E ty Ea he a pj a a i i ait mo lk J m F i wish eae l ily rae pice TG
Download Pdf Manuals
Related Search