NX-216 Install Manual
Contents
1. Dip switch 4 Dip switch 4 is used to disable the second block of eight 8 zones on this zone expander This can be done if only an eight 8 zone expander is required in a particular expander location In this case up to 5 expanders can be added to the system creating a total of 48 zones To disable the second group of eight 8 zones on this expander turn dip switch 4 on ENROLLING THE NX 216 EXPANDER The NX 8 has the ability to automatically find and store in its memory the presence of all keypads zone expanders wireless receivers and any other device on the keypad buss This allows these devices to be supervised by the control panel and illuminate the Service LED if one is not detected To enroll the devices enter the program mode of the NX 8 control panel using the procedure outlined in the Installation Manual and enter 9 1 5 When the Program Mode is exited the NX 8 will automatically enroll the device Enrolling takes about 12 seconds during which time the Service LED will illuminate User codes will not be accepted during the enrolling process If a speaker is attached to the NX 8 it will click at this time If a siren or bell is attached to the NX 8 it will sound for about 1 second Once a module is enrolled the Service LED will illuminate if it is not detected by the control panel WIRING THE NX 216 Wire the zones according to the wiring diagram on page 3 NOTE Any unused zones must have the EOL resis2. INSTANT WITH TAMPER ENABLED This zone creates an instant alarm whenever it is tripped and the Armed LED is on This configuration group can be used to enable tamper on a wireless transmitter ENTRY EXIT DELAY 2 WITH TAMPER ENABLED A trip will start entry delay 2 The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed This configuration group can be used to enable tamper on a wireless transmitter 4 y 27774 NX 216 ZONE EXPANDER PROGRAMMING THE ZONE CONFIGURATION AND PARTITION FOR EACH ZONE The programming for all zone information is performed in the NX 8 control panel For instructions on accessing and programming the NX 8 as well as changing the characteristics of a configuration group refer to the NX 8 Installation Manual The following programming information is taken from the NX 8 Installation Manual LOCATION 27 CONFIGURATION GROUP ZONES 9 16 8 segments numerical data Location 27 contains the Configuration Group Zone type for zones 9 16 Segment 1 is for zone 9 Segment 8 is for zone 16 Default configurations are found in the table on page 4 LOCATION 28 PARTITION SELECT ZONES 9 16 8 segments feature selection data Location 28 is used to select the partition s that zones 9 16 reside in A zone may reside in any combination of the 8 partitions If a burglary zone resides in more than 1 partition it will only be active when all partitions are armed A zone that res
3. is tripped and the Armed LED is on 24 HOUR SILENT Creates an instant silent alarm regardless of the armed state of the control panel It will not display on the keypad FIRE This zone will illuminate the Fire LED and sound the steady siren each time the zone is shorted It will also rapidly flash the Fire LED indicating a trouble if the zone is open ENTRY EXIT DELAY 2 A trip will start entry delay 2 The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed 24 HOUR SILENT SUPERVISED Creates an instant silent alarm regardless of the armed state of the control panel It will display on the keypad KEYSWITCH ZONE This zone type will arm and disarm the partition or partitions of the control panel that resides in each time the zone is shorted Keyswitch arming will report as user 99 INTERIOR FOLLOWER WITH CROSS ZONE ENABLED This zone will be Instant when the system is armed and no entry or exit delay is being timed It is delayed during entry and exit delay times If a Cross Zone is not being timed it will start a Cross Zone timer If a Cross Zone is being timed it will create an Instant alarm This zone will bypass in Stay Mode and automatically bypass when enabled in Segment 1 Location 23 INSTANT ENTRY GUARD This zone creates an instant alarm whenever it is tripped and the Stay LED is off It will start an entry delay time 1 if it is tripped and the system is armed and the Stay LED
4. 2 Partition 2 3 Partition 3 4 Partition 4 5 Partition 5 6 Partition 6 7 Partition 7 8 Partition 8 LOCATION 35 CONFIGURATION GROUP ZONES 41 48 8 segments of numerical data Location 35 contains the Configuration Group Zone type for zones 41 48 Segment 1 is for zone 41 Segment 8is for zone 48 Default configurations are found in the table on page 4 LOCATION 36 PARTITION SELECT ZONES 41 48 8 segments feature selection data Location 36 is used to select the partition or partitions that zones 41 48 reside in A zone may reside in any combination of the 8 partitions If a burglary zone resides in more than 1 partition it will only be active when all partitions are armed A zone that resides in more than 1 partition will be reported to its lowest partition Location 36 has 8 segments Segment 1 corresponds to zone 41 and Segment 8 corresponds to zone 48 Segments 1 8 1 Partition 1 2 Partition 2 3 Partition 3 4 Partition 4 5 Partition 5 6 Partition 6 7 Partition 7 8 Partition 8 y 27774 NX 216 ZONE EXPANDER SYSTEM NOTES SPECIFICATIONS OPERATING POWER 12VDC Supplied from NX 8 or NX 320 AUXILIARY POWER Supplied from NX 8 or NX 320 Current limited to 100mA CURRENT DRAW 30mA LOOP RESISTANCE 300 Ohms Maximum LOOP RESPONSE Selectable 50mS or 500mS OPERATING TEMPERATURE 32 to 120 degrees F DIMENSIONS 6 0 Wide 2 125 High 1 0 Deep SHIPPING WEIGHT 2 Ibs FIVE YEAR
5. ED will See page 2 for instructions Luie F zs S flash during P about setting these C S 8 Normal switches x 191d Operation oC 2 s LO er Ir Zr of gr yr gf rab Pos Com Data Tam Aux Z9 Com Z10 Zit Com Z12 2713 Com Z14 Z15 Com Z16 Z17 Com Z18 Z19 Com Z20 Z21 Com Z22 223 Com 724 ZONES Pos Com and Data Connect to keypad terminals on the NX 8 ar the NX 320 Tam Connect to Com terminal through a normally closed switch ZONE CONNECTIONS Aux Current limited to 100mA MUST BE ADDED TO CONTROL AUX POWER z C ANY ZONE Z9 Z24 Connect as described in the terminal description eg TERMINALS TEMA MAXIUMUM WIRE RUN MAXIUMUM WIRE RUN 3 3K TAMPER WHEN CONNECTED TO NX 8 WHEN CONNECTED TO NX 320 EOL CONIACT If using Aux terminal If using Aux terminal e E 250 24 gauge 250 22 gauge oe 500 20 gauge 500 18 gauge 1000 18 gauge 1000 16 gauge y 1500 16 gauge 1500 14 gauge 2500 14 gauge 2500 12 gauge 3 3K s E NORMALLY OPEN NORMALLY CLOSED EOL If NOT using Aux terminal IF NOT using Aux terminal CONIACTWIH CONTACT WITH E OLL 250 24 gauge 500 22 gauge E Q L RESISTOR RESISTOR M 750 24 gauge 750 20 gauge EUROPEAN DOUBLE 1000 22 gauge 1000 20 gauge 2000 20gauge 2000 16 gauge OE CONFIGURATION 2500 18 gauge 2500 16 gauge Medd NX 216 ZONE EXPANDER DEFAULT ZONE CONFIGURATIONS Zones can be programmed to be one of twenty different zone configurations zone types Configur
6. LIMITED WARRANTY CADDX CONTROLS INC GUARANTEES THIS PRODUCT AGAINST DEFECTIVE PARTS AND WORKMANSHIP FOR TWENTY FOUR 24 MONTHS FROM DATE OF MANUFACTURING IF ANY DEFECT APPEARS DURING THE WARRANTY PERIOD RETURN IT TO CADDX POSTAGE PREPAID THE UNIT WILL BE REPAIRED AND RETURNED AT NO CHARGE FOR THE REMAINING 36 MONTHS OF WARRANTY THE CHARGE TO REPAIR OR REPLACE THIS MODULE WILL NOT EXCEED 10 00 PLUS SHIPPING AND HANDLING CADDX ASSUMES NO LIABILITY FOR CONSEQUENTIAL OR INDIRECT DAMAGE AND ACCEPTS NO RESPONSIBILITY FOR REPAIRING DAMAGE TO THE PRODUCT CAUSED BY MISUSE CARELESS HANDLING OR WHERE REPAIRS HAVE BEEN MADE BY OTHERS NO OTHER GUARANTEE WRITTEN OR VERBAL IS AUTHORIZED BY OR ON BEHALF OF CADDX CONTROLS INC GLADEWATER TEXAS CADDX CONTROLS INC 1420 NORTH MAIN STREET GLADEWATER TEXAS 75647 TOLL FREE 800 727 2339 FAX 903 845 6811 NX 216 INSTALLATION MANUAL NX2161E98 REV E 07 20 98
7. NX 216 TONE EXPANDER INSTALLATION MANUAL Table of Contents General Description 4 Position Dip Switch Settings Enrolling the NX 216 Expander Wiring the NX 216 Terminal Description Wiring Diagram Default Zone Configurations Programming Zone Configuration amp Partition Specifications and Warranty CADDX CONTROLS INC 1420 NORTH MAIN STREET GLADEWATER TEXAS 75647 TOLL FREE 800 727 2339 FAX 903 845 6811 GENERAL DESCRIPTION The NX 216 is a microprocessor controlled 16 zone expander for the NX 8 control panel Up to five NX 216 expanders can be added to the NetworX control panel with a maximum zone count of 48 zones Each expander has an optional tamper switch and power isolator making it ideal for use in a remote location 4 POSITION DIP SWITCH SETTINGS The first thing that must be decided is the starting zone of this particular zone expander The starting zone must be on a boundary of eight 8 zones The sixteen 16 zones for this module will move out from this starting position There are stick on zone labels to indicate the zone numbers that you select To set the starting zone set the dip switch according to the table below NOTE THE POSITION OF ALL SWITCHES IS ONLY UPDATED WHEN THE NX 216 IS POWERED UP BEFORE YOU CHANGE THE POSITION OF THESE SWITCHES YOU MUST POWER DOWN THE EXPANDER Starting Zone Number Dip Switch 1 Dip Switch 2 Dip Switch 3 9 OFF iy OFF 25 OFF 33 ON 41 ON
8. ations 17 through 20 can be used for wireless or hardwired zones using European double EOL configuration The default zone configurations are listed below These zone configurations can be customized by programming locations 110 149 DATA DESCRIPTION OF DEFAULT CONFIGURATION 4 Tp se q Be 6 Cy 2 sg g 4 0 KR 1 4 22 4 q a 4 Ed 5 1 6 na mu 1 8 ni 9 20 DAY ZONE Instant when system is armed trouble zone when system is disarmed 24 HOUR AUDIBLE Creates an instant yelping siren alarm regardless of the armed state of the control panel ENTRY EXIT DELAY 1 A trip will start entry delay 1 The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed INTERIOR FOLLOWER WITH AUTO BYPASS DISABLED This zone will be instant when the system is armed and no entry or exit delays are being timed It is delayed during entry and exit delay times This zone will not bypass in Stay Mode nor automatically bypass even if enabled in Segment 1 Location 23 INTERIOR FOLLOWER WITH AUTO BYPASS ENABLED This zone will be instant when the system is armed and no entry or exit delay is being timed It is delayed during entry and exit delay times This zone will bypass in Stay Mode and automatically bypass if enabled in Segment 1 of Location 23 INSTANT This zone creates an instant alarm whenever it
9. ides in more than 1 partition will be reported to its lowest partition Location 28 has 8 segments Segment 1 corresponds to zone 9 and Segment 8 corresponds to zone 16 Segments 1 8 1 Partition 1 2 Partition 2 3 Partition 3 4 Partition 4 5 Partition 5 6 Partition 6 7 Partition 7 8 Partition 8 LOCATION 29 CONFIGURATION GROUP ZONES 17 24 8 segments numerical data Location 29 contains the Configuration Group Zone type for zones 17 24 Segment 1 is for zone 17 Segment 8is for zone 24 Default configurations are found in the table on page 4 LOCATION 30 PARTITION SELECT ZONES 17 24 8 segments feature selection data Location 30 is used to select the partition s that zones 17 24 reside in A zone may reside in any combination of the 8 partitions If a burglary zone resides in more than 1 partition it will only be active when all partitions are armed A zone that resides in more than 1 partition will be reported to its lowest partition Location 30 has 8 segments Segment 1 corresponds to zone 17 and Segment 8 corresponds to zone 24 Segments 1 8 1 Partition 1 2 Partition 2 3 Partition 3 4 Partition 4 5 Partition 5 6 Partition 6 7 Partition 7 8 Partition 8 LOCATION 31_CONFIGURATION GROUP ZONES 25 32 8 segments numerical data Location 31 contains the Configuration Group Zone type for zones 25 32 Segment 1 is for zone 25 Segment 8 is for zone 32 Default configurations a
10. is on ENTRY EXIT DELAY 1 WITH GROUP BYPASS ENABLED A trip will start entry delay 1 This zone will bypass when the Group Bypass command is entered at the keypad The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed INTERIOR FOLLOWER WITH GROUP BYPASS ENABLED This zone will be instant when the system is armed and no entry or exit delays are being timed It is delayed during entry exit delay times This zone will bypass when the Group Bypass command is entered at the keypad This zone will bypass in Stay Mode and automatically bypass even if enabled in Segment 1 Location 23 INSTANT WITH GROUP BYPASS ENABLED This zone creates an instant alarm whenever it is tripped and the Armed LED is on This zone will bypass when the Group Bypass command is entered at the keypad ENTRY EXIT DELAY 1 WITH TAMPER ENABLED A trip will start entry delay 1 The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed This configuration group can be used to enable tamper on a wireless transmitter INTERIOR FOLLOWER WITH TAMPER AND AUTO BYPASS ENABLED This zone will be instant when the System is armed and no entry or exit delay is being timed It is delayed during entry and exit delay times This zone will bypass in Stay Mode and automatically bypass if enabled in Segment 1 Location 23 This configuration group can be used to enable tamper on a wireless transmitter
11. re found in the table on page 4 5 y 27774 NX 216 ZONE EXPANDER LOCATION 32 PARTITION SELECT ZONES 25 32 8 segments feature selection data Location 32 is used to select the partition s that zones 25 32 reside in A zone may reside in any combination of the 8 partitions If a burglary zone resides in more than 1 partition it will only be active when all partitions are armed A zone that resides in more than 1 partition will be reported to its lowest partition Segment 1 corresponds to zone 25 and Segment 8 corresponds to zone 32 Segments 1 8 1 Partition 1 2 Partition 2 3 Partition 3 4 Partition 4 5 Partition 5 6 Partition 6 7 Partition 7 8 Partition 8 LOCATION 33 CONFIGURATION GROUP ZONES 33 40 8 segments numerical data Location 33 contains the Configuration Group Zone type for zones 33 40 Segment 1 is for zone 33 Segment 8is for zone 40 Default configurations are found in the table on page 4 LOCATION 34 PARTITION SELECT ZONES 33 40 8 segments of feature selection data Location 34 is used to select the partition s that zones 33 40 reside in A zone may reside in any combination of the 8 partitions If a burglary zone resides in more than 1 partition it will only be active when all partitions are armed A zone that resides in more than 1 partition will be reported to its lowest partition Segment 1 corresponds to zone 33 and Segment 8 corresponds to zone 40 Segments 1 8 1 Partition 1
12. tor across it unless all eight are disabled by dip switch 4 y 27774 NX 216 ZONE EXPANDER TERMINAL DESCRIPTION TERMINAL DESCRIPTION POS Connect to the KP POS terminal of the NX 8 Current draw is 30 mA COM Connect to the KP COM terminal of the NX 8 DATA Connect to the KP DATA terminal of the NX 8 See the wiring diagram for wire specifications TAM Connect as shown below IF NOT USED CONNECT TO A COM TERMINAL Can be used to power devices directly from the NX 216 Power is coming from the NX 8 therefore the current draw of these devices must be added to the total current draw of the NX AUX 216 This output is current limited to 100 mA Connect to one side of zone 9 loop Connect the other side to COM terminal Open or short Z9 causes alarm See the wiring diagram for examples COM Common terminal for zones 9 amp 10 Connect to one side of zone 10 loop Connect the other side to COM terminal Open or short Z10 causes alarm See the wiring diagram for examples 211 224 Connect as described for Z9 amp Z10 WIRING DIAGRAM olelslzliele y 9 zXN 4epuodx3 euoz ol Is O This LED is only QU sj041u02 IPPDIXPPDO O for proper circuit co operation zn C3 LS ud a gt 3 uk LISa 1234 Ln zsa ht ie ait xh This L
Download Pdf Manuals
Related Search