User Manual for your
Contents
1. User Manual for your Baumatic BS65MS 60 cm Multifunction oven x Baumatic NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a safe place so that it is easily available for future reference for you or any person not familiar with the operation of the appliance JW 19 06 12 Contents Environmental note Important safety information Specifications Product and aperture dimensions Product specifications Standard accessories Electrical details Control panel Oven programmer timer display Setting and using the oven programmer timer Selecting manual operation mode Setting the time of day Before first use Setting the minute minder function Setting the semi automatic cooking function Setting the end cook function Setting the auto cooking function Cancelling a cooking function Changing the time of day Selecting a cooking function and temperature Selecting an oven function Oven functions Thermostat control knob Oven operating light Cooking guidelines Warnings Shelf positions Cleaning and maintenance Replacing the oven bulb Removing the oven door for cleaning Removing the inner door glass for cleaning Installation Electrical connection Installing the oven into the kitchen cabinet Positioning the appliance Ventilation requirements M2. Press and hold down the minus 13 and plus 11 buttons Simultaneously o The minute minder symbol 10 will go out O IMPORTANT If you do not turn the oven function selector knob and thermostat control knob to their OFF positions when you reset the timer function it will continue to heat Adjusting the volume of the audible signal The volume of the audible signal has 3 levels low medium and high To adjust the volume you should proceed as follows O O IMPORTANT The oven timer programmer must not be in any form of countdown mode and the oven in use symbol 8 must be lit Press and hold down the minus 13 and plus 11 buttons Simultaneously until the decimal point starts to flash Press the programme button 12 and the LED display will show n followed by a number 1 is the loudest volume 2 is the middle volume and 3 is the quietest volume Use the minus button to select the volume level that you desire 16 Changing the time of day o IMPORTANT The oven timer programmer must not be in any form of countdown mode and the oven in use symbol 8 must be lit o Press and hold down the minus 13 and plus 11 buttons Simultaneously until the decimal point starts to flash o Release these buttons and then use the minus and plus buttons to alter the time of day Selecting a cooking function and temperature Selecting an oven function The oven function selector knob should be used to select th
3. next page o Ensure that the rear panel of the furniture housing unit has been removed 25 Ventilation requirements Support rail to be removed Remove rear panel from this section 85 90 mm spacing between wall S and rear of support A shelf and cabinet base d iaa r Figure shows the ventilation and cut out requirements for the installation of the appliance into a standard kitchen unit Minimum ventilation requirements for rear of unit top base and support shelves Storage space Rear panel Remove rear from this section storage space Rear panel Plinth Minimum ventilation cut out 200cm Figure shows the ventilation and cut out requirements for the installation of the appliance into a tall housing unit 26 o Ensure that the oven has been securely fixed into the housing unit The fixing of the oven into the housing is made by using four screws These should be screwed through the oven cabinet and into the housing unit My appliance isn t working correctly o The oven isn t coming on Check that the oven is in manual operation mode Check that you have selected a cooking function and a cooking temperature o There appears to be no power to the oven and grill Check that the appliance has been connected to the electrical mains supply correctly Check that the mains fuses are in working order Check that the operating instru
4. 25 W 300 C screw type pygmy For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice The rating plate for your oven can be located by opening the oven door and looking around the outer edge of the oven chassis Model Number Serial Number Date of Purchase Control Panel 1 Oven function selector knob 2 Thermostat control knob 3 Power indicator light 4 Oven operating light 5 LED display 6 Oven programmer timer Oven programmer timer 18 9 13 12 11 Automatic cooking symbol Oven in use symbol Decimal point symbol Minute minder symbol Plus button 7 8 9 10 11 12 Programme button 13 0 1 2 3 Minus button 10 Initial set up of your oven Selecting manual operation mode After your appliance is connected to your mains supply for the first time the numbers on the timer display will flash Before you can select a cooking function or set a temperature you must set the appliance into manual operation mode o To select manual operation mode press the manual button 12 on the control panel Setting the time of day After your appliance is connected to your mains supply for the first time you must set the time of day before you can use the oven o When the oven is connected to your mains supply for the first time or after a power cut the digits on
5. Ltd Private Bag 92900 Onehunga Auckland 1061 New Zealand Website www baumatic co nz United Kingdom Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 0QX United Kingdom Sales Telephone 0118 933 6900 Website www baumatic co uk 30 31
6. countdown time similar to the minute minder function however the oven will switch off at the end of the cooking time O Place the food that you want to cook inside of the oven and close the door Select an oven function and cooking temperature using the relevant control knobs Press and hold down the programme button 12 until the decimal point starts to flash to enter programming mode the oven in use symbol 8 will appear on the LED display Release the programme button and then press it again The automatic cooking symbol 7 will flash and dur will appear briefly on the LED display before showing 0 00 Use the plus 11 and minus 13 buttons to set the cooking time that you require The maximum countdown time that can be set is 10 hours When the correct countdown time appears on the LED display release the plus and minus buttons Cooking will begin immediately after a few seconds the countdown time will start The automatic cooking symbol and the oven in use symbol 8 will appear on the LED display At the end of the cooking time an audible signal will sound and the automatic cooking symbol will flash on the LED display To reset the oven and cancel the audible alarm press the programme button until the oven in use symbol appears on the LED display and the automatic cooking symbol goes out IMPORTANT If you have not turned the oven function selector Knob and thermostat control knob to their OFF p
7. ctions for putting the appliance into manual operation mode have been followed o The grill function works but the main oven does not Check that you have selected the correct cooking function o The grill and top oven element is not working or cuts out for long periods of time during use Allow the oven to cool for approximately 2 hours Once cool check whether the appliance is again working properly 27 My food is not cooking properly Ensure that you are selecting the correct temperature and the correct cooking function for the food that you are cooking It may be appropriate to adjust your cooking temperature by plus or minus 10 C to achieve the best cooking results My food is not cooking evenly Check that the oven has been installed correctly and is level Check that the correct temperatures and shelf positions are being used The oven light is not working Refer to page 21 and follow the Replacing the oven bulb section am getting condensation in my oven Steam and condensation is a natural by product of cooking any food with high water content such as frozen food chicken etc You may get condensation in the oven cavity and forming between the oven door glasses This is not necessarily a sign that the oven is not working correctly Do not leave food in the oven to cool after it has been cooked and the oven has been switched off Use a covered container where practical when cooking to reduce th
8. d leave gaps between the trays to allow air to circulate Try to open the door as little as possible to view the dishes The oven light will remain on during cooking Warnings O Keep the oven door closed when using ALL oven functions including the grill function Do not use aluminium foil to cover the enamelled baking tray or heat items wrapped in aluminium foil under the grill The high reflectivity of the foil could potentially damage the grill element You should also never line the base of your oven with aluminium foil During cooking never place pans or cookware directly onto the bottom of your oven They should always be placed on the shelf provided The grill heating element becomes extremely hot during operation avoid touching it inadvertently when handling the food which you are grilling Important Be careful when opening the door to avoid contact with hot parts and steam 19 Shelf levels o Safety shelf A o Removable side racks which allow you to cook on six different levels B o Enamelled baking tray C o The numbers 1 6 indicate the different shelf positions that you can utilise within the oven Cleaning and maintenance Cleaning operations must only be carried out when the oven is cool The appliance should be disconnected from your mains supply before commencing any cleaning process o The oven should be thoroughly cleaned before it is operated for the first tim
9. e amount of condensation that forms 28 IMPORTANT If your appliance appears not to be operating correctly then you should disconnect it from your mains supply and then contact the Service Department DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault then you may be liable for the cost of the call out charge The appliance must be accessible for the engineer to perform any necessary repair If your appliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen then he will not complete a repair This includes situations where appliances have been tiled in sealed in with sealant have wooden obstructions placed in front of the appliance like plinths Or any installation other than the one specified by Baumatic Ltd has been completed Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance IMPORTANT Baumatic Ltd operates a policy of continuous improvement and reserves the right to adjust and modify its products without prior notification 29 lt f px Baumatic Think Appliances Pty Ltd 416 424 Barry Rd Coolaroo VIC 3048 Sales Telephone 1300 132 824 Service Telephone 1800 444 357 Website www thinkappliances com Applico
10. e and after each use This will avoid residual food Stuffs becoming baked on the oven cavity After residues have been baked on several times they are far more difficult to remove o Never clean the oven surfaces by steam cleaning o The oven cavity should only be cleaned with warm soapy water using either a sponge or soft cloth No abrasive cleaners should be used o Any stains that may appear on the bottom of the oven will have originated from food splashes or spilt food these splashes occur during the cooking process These could possibly be a result of the food being cooked at an excessively high temperature or being placed in cookware that is too small o You should make sure that the cooking temperature that is selected is appropriate for the food that you are cooking You Should also ensure that the food is placed in an adequately sized dish and use the enamelled baking tray where appropriate 20 o Outer parts of the oven should only be cleaned with warm soapy water using either a sponge or soft cloth No abrasive cleaners Should be used o We would recommend that an appropriate stainless steel cleaner and polish is regularly used on the stainless steel surfaces of this appliance o If you use any form of oven cleaner on your appliance then you must check with the manufacturer of the cleaner that it is Suitable for use on your appliance o Any damage that is caused to the appliance by a cleaning product will not be fix
11. e particular mode of cooking that you require The appliance will utilise different elements within the oven cavity depending on the oven function that you select When a function is selected the power indicator light will come on Oven functions DEFROST MODE The fan runs without heat to reduce the s defrosting time of frozen foods The time required to defrost b the food will depend on the room temperature the quantity and type of food Always check food packaging for the defrosting instructions CONVENTIONAL OVEN top and lower element This method of cooking provides traditional cooking with heat from the top and lower elements This function is suitable for roasting and baking on one shelf only W FAN AND GRILL This method of cooking utilises the top ie element in conjunction with the fan which helps to provide a quick circulation of heat This function is suitable where quick browning is required and sealing the juices in such as steaks hamburgers some vegetables etc 17 FAN AND LOWER ELEMENT This method of cooking utilises s the lower element in conjunction with the fan which helps to circulate the heat This function is suitable for sterilizing and preserving jars l CONVENTI ONAL OVEN AND FAN This method of cooking is zr a conventional cooking method the oven heat comes from the top element and the bottom element and the fan helps to circulate the heat to achieve an even baking result Th
12. ed by the manufacturer free of charge even if the appliance is within the guarantee period Replacing the oven bulb IMPORTANT The oven must be disconnected from your mains supply before you attempt to either remove or replace the oven bulb o Remove the oven shelf and the drip tray o Remove the light cover by turning it anti clockwise o Unscrew the bulb clockwise and remove it from its holder o Replace the bulb with a 25 W 300 C screw type pygmy o Do not use any other type of bulb o Place the lamp cover back into position 21 Removing the oven door for cleaning To facilitate the cleaning of the inside of the oven and the outer frame of the oven the door can be removed as follows o Open the door fully o The hinges A have two movable bolts on them B o If you raise both of the movable bolts B then the hinges A are released from the oven housing o You should grip the sides of the door at the centre and then incline it slightly towards the oven cavity and then pull the door gently away from the oven cavity WARNING Care should be taken as the inner edges of the door may be sharp o IMPORTANT You should make sure that the door is supported at all times and that you place the door on some padded material whilst cleaning it o The oven door and door glass should only be cleaned using a damp cloth and a small amount of detergent The cloth MUST NOT have come into contact with any f
13. ermostat control knob o The oven thermostat control knob sets the required temperature of the oven It is possible to regulate the temperature within a range of 50 250 C o Turn the control knob clockwise o This light will come on to indicate that the oven s heating elements are in operation The light will turn off when the temperature set on the thermostat control knob has been reached It will cycle on and off throughout the cooking time You should not place food inside the cavity until the correct cooking temperature has been reached Cooking guidelines o Please refer to the information given on food packaging for guidance on cooking temperatures and times Once familiar with the performance of your appliance temperatures and times can be varied to suit personal preference o If you are using the conventional oven function then you should follow the information given on the food packaging for this particular mode of cooking 18 You should pre heat the oven and not place food inside of it until the oven operating light has gone off IMPORTANT You should ALWAYS pre heat the oven if you are baking Make sure that frozen foods are thoroughly thawed before cooking unless the instructions on the food packaging advise that you can cook from frozen Before cooking check that any accessories that are not required are removed from the oven Place cooking trays in the centre of the oven an
14. ish is regularly used on the stainless steel surfaces of this appliance Timer functions The minute minder function The minute minder function is a countdown time that can be set on the oven programmer timer When the countdown time has finished an audible signal will sound o Press and hold down the programme button 12 until the decimal point starts to flash to enter programming mode o Use the plus 11 and minus 13 buttons to set the countdown time that you require o The maximum countdown time that can be set is 23 hours and 59 minutes o When the correct countdown time appears on the LED display release the plus and minus buttons and the countdown will start immediately o The oven in use symbol 8 will appear on the LED display to Show that a countdown time is in progress o After a few seconds the LED display will return to showing the time of day o At the end of the countdown time an audible signal will sound and the oven in use symbol will go out The audible signal will sound for 7 minutes before switching off or you can silence it by pressing any of the oven programmer timer buttons o IMPORTANT If the oven is in use whilst using the minute minder function the oven WILL NOT switch off at the end 12 of the countdown time YOU MUST turn the oven function selector knob and the thermostat control knob to their OFF positions The semi automatic cooking function This function will allow you to set a
15. orm of cleaning product or chemical previously o To refit the door you should slide the hinges back into their slots and open the door fully o IMPORTANT The movable bolts B must be closed back into their original positions before closing the door o Take care not to dislodge the hinge locking system when removing the door as the hinge mechanism has a strong spring o Do not immerse the door in water at any time Zz Removing the inner door glass for cleaning O Do not use any abrasive cleaner that could cause damage Remember that if the surface of the glass panel becomes scratched this could lead to a dangerous failure To facilitate cleaning the inner door glass can be lifted out Unscrew the bracket latch that is in the corner of the top of the door Remove the glass from the door and clean with warm soapy water After cleaning insert the glass panel correctly back into the door Screw the bracket latch back into place IMPORTANT Remember where the panel of glass is removed from so you can reassemble the door correctly Do not mix the glasses up or rearrange the order 23 INSTALLATION The installation must be carried out by a suitably A N qualified person in accordance with the current version of the following o AS NZS 3000 2007 Wiring Regulations o 2010 Electricity Safety Regulations Electrical connection Before connecting the appliance make sure that the supply voltage marked on
16. ositions when you reset the oven it will continue to heat 13 The end of cooking function This function is similar to the semi automatic function however instead of setting a countdown time you select the time of day that you want the oven to switch off at O Place the food that you want to cook inside of the oven and close the door Select an oven function and cooking temperature using the relevant control knobs Press and hold down the programme button 12 until the decimal point starts to flash to enter programming mode the minute minder symbol 10 will appear on the LED display Release the programme button and then press it again The automatic cooking symbol 7 will flash and dur will appear on the LED display Release the programme button and then press it for a third time end will appear briefly on the LED display before Showing the current time of day Use the plus 11 and minus 13 buttons to set the time of day that you want the oven to switch off at The maximum countdown time that can be set is 10 hours When the correct time of day appears on the LED display release the plus and minus buttons Cooking will begin immediately after a few seconds the countdown time will start The automatic cooking symbol and the oven in use symbol 8 will appear on the LED display At the end of the cooking time an audible signal will sound and the automatic cooking symbol will flash on the LED dis
17. play To reset the oven and cancel the audible alarm press the programme button until the oven in use symbol appears on the LED display and the automatic cooking symbol goes out IMPORTANT If you have not turned the oven function selector Knob and thermostat control knob to their OFF positions when you reset the oven it will continue to heat 14 The automatic cooking function This function will allow you to set the time of day that you want the oven to switch off at and how long you want the oven to cook for O Place the food that you want to cook inside of the oven and close the door Select an oven function and cooking temperature using the relevant control knobs Press and hold down the programme button 12 until the decimal point starts to flash to enter programming mode the minute minder symbol 10 will appear on the LED display Release the programme button and then press it again The automatic cooking symbol 7 will flash and dur will appear briefly on the LED display before showing 0 00 Use the plus 11 and minus 13 buttons to set the cooking time that you require The maximum countdown time that can be set is 10 hours When the correct countdown time appears on the LED display release the plus and minus buttons IMMEDIATELY press the programme button end will appear briefly on the LED display before showing a calculated end of cooking time Use the plus 11 and minus 13 b
18. pliance surfaces will become hot during use and retain heat after operation Child Safety O Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time If it is necessary for younger family members to be in the kitchen please ensure that they are kept under close supervision at all times General Safety Do not place heavy objects on the oven door or lean on the oven door when it is open as this can cause damage to the oven door hinges Do not leave heated oil or fat Unattended as this is a fire risk Do not place pans or baking trays directly on the base of the oven cavity or line it with aluminium foil Do not allow electrical fittings or cables to come into contact with areas on the appliance that get hot Do not use the appliance to heat the room it is located in or to dry clothing Do not install the appliance next to curtains or soft furnishings Do not attempt to lift or move cooking appliances by using the oven door or handle as this may cause damage to the appliance or result in injury to the person lifting the appliance Cleaning O Cleaning of the oven should be carried out on a regular basis Great care should be taken whilst using this appliance and when following the cleaning procedure IMPORTANT The appliance must be disconnected from the mains before following the cleaning procedure Installa
19. s booklet please contact the retailer where you purchased your unit from General I nformation o This appliance is designed for domestic household use and can be built into a standard kitchen cabinet or housing unit o IMPORTANT The adjacent furniture or housing and all materials used in the installation must be able to withstand a minimum temperature of 85 C above the ambient temperature of the room it is located in whilst in use o Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage or discolouration at temperatures below the guidelines given above o Any damage caused by the appliance being installed in contravention of this temperature limit or by placing adjacent cabinet materials closer than 4mm to the appliance will be the liability of the owner o The use of this appliance for any other purpose or in any other environment without the express agreement of Baumatic Ltd will invalidate any warranty or liability claim o Your new appliance is guaranteed against electrical or mechanical defects subject to certain exclusions that are noted in the Conditions Of Guarantee The foregoing does not affect your statutory rights o Repairs may only be carried out by authorised service engineers Warning and safety instructions o This appliance complies with all current European safety legislation Baumatic does wish to emphasise that this compliance does not remove the fact that the ap
20. the LED display and the automatic cooking symbol 7 will flash o Press and hold down the programme button 12 for a couple of seconds The automatic cooking symbol will go out and the digits will remain steady o Whilst the decimal point symbol 9 is flashing use the plus 11 and minus 13 buttons to set the correct time of day o When the correct time of day is shown on the LED display release the plus and minus buttons and wait a few seconds The decimal point symbol will stop flashing and the oven is ready to use Before first use o To remove any residue from the oven that may have been left from the manufacturing process you should select the fan oven function and set the thermostat to its maximum temperature setting o It is perfectly normal for a smell to be produced during this process o You should make sure that any windows in the room are left open during this process o It is advisable for you not to remain in the room whilst the burning off process is taking place 11 o You should leave the oven on maximum setting for 30 40 minutes o After the oven cavity has cooled it should then be cleaned with warm soapy water using either a sponge or soft cloth No abrasive cleaners should be used o Outer parts of the oven should be cleaned with warm soapy water using either a sponge or soft cloth No abrasive cleaners Should be used o We would recommend that an appropriate stainless steel cleaner and pol
21. the rating plate corresponds with your mains supply voltage WARNI NG THIS APPLI ANCE MUST BE EARTHED o This appliance should be wired into a 15 A double pole switched fused spur outlet having 3 mm contact separation and placed in an easily accessible position adjacent to the appliance The spur outlet must still be accessible even when your oven is located in its housing MAINS LIVE 1 BROWN POWER el ol Beye BORD NEUTRAL N Ae _ o To connect the oven power cord loosen and remove the cover on the terminal block in order to gain access to the contacts inside Make the connection securing the cord in place with the cable clamp provided and then immediately close the terminal block cover again o If you have to change the oven power cord the earthing yellow green conductor must always be 10 mm longer than the line conductors o Care must be taken to ensure that the temperature of the mains supply cable does not exceed 50 C o Ifthe mains supply cable is damaged then it must be replaced by an appropriate replacement which can be obtained from the Spares Department 24 Installing the oven into the kitchen cabinet Positioning the appliance o Ensure that the aperture that you will be fitting the oven into is of the size given in the above diagram o The oven must be fitted into an oven housing with the ventilation cut outs shown in the Ventilation requirements section on the
22. tion This appliance must be correctly installed by a Suitably qualified person strictly in accordance with the manufacturer s instructions o Baumatic Ltd declines any responsibility for injury or damage to person or property as a result of improper use or installation of this appliance o Heat steam and moisture will be created during use of the appliance take care to avoid injury and ensure that the room is adequately ventilated If the appliance is going to be used for prolonged periods of time then additional ventilation may be required o Please consult with your qualified installer if you are in any doubt about the amount of ventilation that you will require Specifications Product Dimensions Aperture Dimensions Height 590 mm 580 mm 583 mm Width 595 mm 560 mm Depth 550 mm 550 mm min Product specifications O G O 0O O 0 O 5 oven functions Energy efficiency class A Oven gross capacity 59 litres Oven net capacity 50 litres LED full programmer Oven light Cooling fan Double glazed removable door Removable inner door glass Standard accessories O O 0 O O Safety shelf Enamelled baking tray with handle Trivet Removable side racks BPS2 Pizza stone Electrical details Rated Voltage Supply Connection Max Rated Inputs Mains Supply Lead Oven Light Bulb 220 240 Vac 50 Hz 15 A double pole switched fused outlet with 3mm contact gap 2 30 kW 3 x 1 5mm
23. uttons to set the time of day that you want the oven to switch off at The automatic cooking symbol and the time of day will appear on the LED display The appliance will automatically calculate what time of day it needs to switch the oven on at so that it runs for the cooking time that you set When the oven switches on the oven in use symbol 8 will appear on the LED display as well as the automatic cooking symbol At the end of the cooking time an audible signal will sound and the automatic cooking symbol will flash on the LED display 15 O To reset the oven and cancel the audible alarm press the programme button until the oven in use symbol appears on the LED display and the automatic cooking symbol goes out IMPORTANT If you have not turned the oven function selector Knob and thermostat control knob to their OFF positions when you reset the oven it will continue to heat Cancelling the semi automatic and automatic function O Press and hold down the minus 13 and plus 11 button Simultaneously until the automatic cooking symbol 7 goes out and the oven in use symbol 8 is lit IMPORTANT If you do not turn the oven function selector Knob and thermostat control knob to their OFF positions when you reset the timer function it will continue to heat Cancelling the minute minder function O Press and hold down the programme button 12 until the decimal point starts to flash to enter programming mode
24. y appliance isn t working correctly Baumatic consumables Contact details Environmental note This appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol _ on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product o The packaging materials that Baumatic uses are environmentally friendly and can be recycled o Please discard all packaging material with due regard for the environment IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information contained in thi
Download Pdf Manuals
Related Search