INSTALLATION AND USER MANUAL code: 80991 - 10
Contents
1. Dimensions in mm GF VEDO SL 35CT GF VEDO SL 70CT V70CT Figure 3 Free spaces for ventilation Attention the temperature inside the compartment that houses the integrated Controller and Operator Panel must never exceed 50 C The free spaces highlighted in grey are those recommended with static ventilation With forced ventilation these spaces can be reduced even further 10 80991_MHW_GF_VEDO SL_10 2012_ENG Assembly of Integrated Controller and Operator Panel Hole dimensions For correct installation observe the dimensions of the templates shown in the illustration The dotted line shows the maximum size of the front panel Attention the panel on which the Integrated Controller and Operator Panel is mounted has to have the following cha racteristics e be sufficiently stiff and strong so that it does not bend during use e be betwee2. 0 9 134 4 a GF_VEDO SL V70CT Dimensions in mm Figure 2 Dimensions GF_VEDO SL 80991_MHW_GF_VEDO SL_10 2012_ENG 9
3. 2888 l J L J L J L JU Dimensions in mm GF_VEDO SL 35CT Dimensions in mm GF_VEDO SL 70CT
4. SL MODELS 35CT 70CT V70CT 7 OCMC eric i 7 Dimensions and spaces required for installation 9 ASSEMBLY AND INSTALLATION 1 eee ne enne 11 Assembly of Integrated Controller and Operator Panel 11 Hole dimensions curi 11 Protection against infiltrations of water 11 Mileirzid e STER TETTE 11 Minimum spaces for ventilation 11 FOSMIO NNN ERR RE ER e E 11 Fastening to the panel 12 Integrated Controller and Operator Panel Connections 13 Inputs ports and signals sees 13 POW Se a ce ticosit ake n Uusn d ecubm iub dcMuE S E adbuc eM MLEnd Ha MEE DRE EE 13 CAN 14 SEY VS Bc ERREUR TR 14 DB sated tic scat M 15 FM M atone ela 15 uo 15 Rocca 15 80991 MHW GF VEDO SL 10 2012 ENG ENTRY INTO SERVICE Lin 16 SEet U PIOGrAni aracunalle lisina 16 MAME 16 COMMOUNATION sica 16 ba bri 17 Biioy M 17 Touchscreen calibration eese 17 MONNA O DNE mS 18 CGANODET Sess unt odds vbetuu cusam sa ettapicenctem enue a i iru SU 18 MODESTI CR ai 18 Modus RT oesi 18 System Message FaUlt i 19 Uploading the application program esses 19 MAINTENANCE AND DIAGNOSTICS 20 WVU G
5. The Network button allows access to the device configura tion procedures The Display button allows access to information on the firmware and communication protocols installed The Touchscreen Calibration button will allow future ac cess to the procedure for the calibration of the touch screen without using the dial To regulate the date proceed as follows 1 Touch the year with a finger The numeric keypad appe ars Type in the year and press Enter The changed year appears underlined 2 Touch the month with a finger The numeric keypad appears Type in the month in the 2 figure format and press Enter The changed month appears underlined 3 Touch the day with a finger The numeric keypad ap pears Type in the day in the 2 figure format and press Enter The changed day appears underlined 4 Press SAVE to save the changes made When the new date has been saved the underlining disappears To regulate the time proceed as follows 1 Touch the hours with a finger The numeric keypad ap pears Type in the hour in the 24h format and press En ter The changed hour appears underlined 2 Touch the minutes with a finger The numeric keypad appears Type in the minutes in the 2 figure format and press Enter The changed minutes appear underlined 3 Touch the seconds with a finger The numeric keypad appears Type in the seconds in the 2 figure format and press Enter The changed seconds appear underlined 4 Press Save to sa
6. switches see the CAN IO documentation Ethernet If necessary connect the Ethernet cable to the Ethernet RJ45 port The Ethernet port allows connection of the Integrated Con troller and Panel to a computer or to a company LAN net work The connection cable to use either straight or crossover depends on the type of device that has to be connected For example to directly connect a PC it is necessary to use a crossover cable Crossover cable Straight cable Figure 13 straight and crossover Ethernet cables For the connection use a CAT6 UTP cable or superior The maximum length of the Ethernet cable is 100 metres Do not run the Ethernet cable alongside the machine power cables to avoid interference with data transmission The RJ45 socket has two LEDs When the Ethernet connec tion is active the green LED stays permanently lit when data is being transmitted the yellow LED flashes USB The USB port is optional and is used to connect external devices compliant to the USB standard The connector is Type A and the port supports version USB 2 0 with speed up to 480 Mbit s The port is able to issue a current of 500 mA at 5 Vdc to power USB devices The maximum length allowed for the USB cable is 5 metres Transfer cable It is possible to directly access the USB port of the controller from the panel using the transfer cable accessory to order separately To fit the socket of this cable the panel thicknes
7. the factory is ideal for most situa tions Setting 0 seconds the screen never times out It is advisable to set the shortest possible timeout compati bly with your needs To see the screen again all you have to do is touch any button The Save button memorises the new configuration and the Cancel button cancels the changes and maintains the pre vious configuration parameters The HOME button in the top left corner allows a return to the Main Menu while the BACK button returns to the Confi guration screen Touchscreen calibration To calibrate the touch screen proceed as follows 1 Switch off the device 2 Position the dial on E 3 Switch the device on again The logo page is followed by the calibration screen This screen is used to calibra te the response of the screen when it is touched with a finger 4 Touch the 5 targets precisely with a plastic tip following the order proposed on the screen o After touching the 5th target the system automatical ly exits the calibration procedure and starts the set up program or if it exists the application program 6 Switch off the device 7 Position the dial on O 8 Switch the device on again 80991 MHW GF VEDO SL 10 2012 ENG Information INFORMATION CANopen Modbus TCP Modbus RTU System Message Bootloader G Firmware O 0 FileSystem a RUNTIME ii The HOME button in the top left corner a
8. the set up program 80991_MHW_GF_VEDO SL_10 2012_ENG Disposal The Integrated Controller and Operator Pa nel and the CAN IO module must be dispo sed of in compliance with the laws in force Some of the components used in the devi ces may damage the environment unless di sposed of properly 20 Integrated Controller and Operator Panel Create the codes to suit the device configuration required GF VEDO SL HE HH HEURE 3 5 display 7 horizontal display 7 vertical display Basic memory FLASH 128 MB DRAM 64 MB FRAM 32 kB 1 RS485 RS232 Ports serial RS485 RS232 slot SD card CAN Port Absent CANopen Absent y 0 use Ul Absent Present KA Geran eu OpenFrame o 1 SD and FRAM Available from January 2013 2 Ask for availability 3 Mandatory port for use with remote IO Code examples GF VEDO SL 70CT LXO S1 C1U100G 7 display CANopen RS485 RS232 and USB ports lexan Gefran no keypad GF VEDO SL 35CT LXO 00 C1 U1 K1C 3 5 display CANopen and USB ports lexan customized 6 key keypad 80991_MHW_GF_VEDO SL_10 2012_ENG 21 Programming tool SS ee GF_PROJECT LX Development software that allows the writing of the application program for PLC with IEC1131 languages Also allows the construction in graphic mode of the various pages of the user interface necessary to the application deve loped Via GF_PROJECT LX it is possible to connect to the device that will host the
9. 0MHz Sistem 64 MB tipo SDRAM e 12 MB HMI application e 2 5 MB PLC applicative Retentive e 32 kB retentive variables FLASH FRAM MEMORY e 1 MB data logger FLASH Mass 128 MB tipo FLASH e 32 MB for user Mass extension Slot SD Card optional ENVIRONMENTAL Operating temperature 0 50 C according to IEC 68 2 14 Storage temperature 20 70 C according to IEC 68 2 14 CONDITIONS Relative humidity max 95 RH non condensing according to IEC 68 2 3 ASSEMBLY Embedded in control panels DEGREE OF PROTECTION IP 65 on the front according to IEC 68 2 3 WEIGHT 0 25 kg 0 5 kg EMC conformity Observance of Directive 2004 108 CE electromagnetic EMC Emission EN 61000 6 4 compatibility EMC Immunity EMC EN 61131 2 EN 61000 4 2 EN CE STANDARDS 61000 4 3 EN 61000 4 4 EN 61000 4 5 EN 61000 4 6 Available from January 2013 EN 61000 4 8 EN 61000 4 11 LV conformity low voltage Observance of 2006 95 CE Safety LVD EN 61010 1 80991_MHW_GF_VEDO SL_10 2012_ENG Dimensions and spaces required for installation ac a X UU UE E UU ED
10. 5 Selectthe required PLC program from the list that opens the file extension is PPJS and click the Open button 6 Select Settings from the Communication menu 7 Select the GDB protocol in the Device Link Manager Config window that opens 8 Click the Properties button The Gdb Config Win dow opens Select the TCP IP protocol from the Port dropdown menu and enter the P address indicated at step 2 of the procedure in the IP address box 9 Click the OK button and then press OK again 10 Check the connection Select gt Connect from the Connection menu The PC connects to the controller In the bottom right window the following words appear CONNECT in green NO CODE in yellow If DIFFERENT CODE appears this means that there is already an application program different from the one you are trying to upload on the controller If the word CONNECT does not appear this means that communi cation related settings are incorrect In particular verify the IP address p 19 11 Upload the application onto the controller selecting gt Download Code from the Communication menu Click the Yes button in the warning message that opens The transfer starts and is highlighted on a progress bar 12 At the end of the transfer a window opens and asks you to restart the system Click Yes 13 In the bottom left corner of the Output panel there is a list of the results of the actions performed the message SOURCE OK appears in the
11. GEFRAN This document is the property of GEFRAN and may not be reproduced or transferred to third parties without authorization 80991_MHW_GF_VEDO SL_10 2012_ENG INSTALLATION AND USER MANUAL C code 80991 10 2012 ENG ATTENTION This manual must always be available to operators of the devices described here Always make sure that you have the latest version of the manual which is available for free download from the GEFRAN website www gefran com Installers and or maintenance personnel are required to read this manual and to precisely follow the instructions contained in it and in its attachments GEFRAN will not be liable for any damage to persons and or property or to the product itself caused by failure to follow the instructions and observe the warnings given below This manual and its attachments may be freely reproduced as long as they are not changed in any way and every copy contains this warning and the declaration of ownership by Gefran S p A 80991_MHW_GF_VEDO SL_10 2012_ENG SUMMARIES AND TABLES OF CONTENTS 3 lal elc 4 Warning and Safety uil 4 Printing conventions used in the manual 4 elec Mew c n 5 zr 6 Overview of the solution and functionalities 6 sei R 6 GF VEDO SERIES
12. IANG B iii iaia od CDM pA AME Ud 20 Integrated Controller and Operator Panel 20 PISS a NOME c 20 Belges 20 Integrated Controller and Operator Panel 20 ORDERING CODES eee eee eeeeee eene nnne einer 21 Integrated Controller and Operator Panel 21 Code examples i 21 ACCESSO Sii 22 Programming 1008 22 GF PROJECT sa 22 3 Warnings and safety While all the information contained in this manual has been carefully checked Gefran S p A accepts no responsibility for the possible presence of errors or for damage to persons and or property caused by the improper use of the manual Gefran S p A also reserves the right to make changes to the contents and form of this manual and to the characteri stics of the devices illustrated at any time and without prior warning The installation of the devices illustrated in the manual must be carried out by qualified technicians in compliance with the laws and standards in force and in agreement with the instructions contained in the manual If the GF VEDO SL is used in applications with the risk of damages to persons machinery or materials its use in con junction with alarms is essential It is advisable to envisage the possibility of checking the in tervention of the alarms during regular operation Before interacting with the Controller a
13. application to debug the program and upload the upgrades System requirements Minimum Recommended Operating system Windows XP SP2 or Windows Vista or Windows 7 64 bit Windows 7 32 bit Processor Intel Pentium 1 GHZ Intel Core i5 2 5 Ghz or superior RAM 2 GB 4 GB or superior Free space on Hard Disk 2 GB 4 GB or superior Graphic resolution XGA 1024 x 768 pixel SXGA 1280 x 1024 pixel or superior Browser Microsoft Internet Explorer 8 0 Microsoft Internet Explorer 9 0 or superior Ethernet port 1 RJ45 DVD player Yes USB port 1 USB 2 0 80991 MHW GF VEDO SL 10 2012 ENG 22 GEFRAN GEFRAN spa via Sebina 74 25050 Provaglio d Iseo BS Italy Tel 39 0309888 1 Fax 39 0309839063 info gefran com http www gefran com
14. ears in absence of power 20 months CONNECTIONS CAN port Opto isolated Connector DB9 M Speed 10 kbit s 1 Mbit s Termination to be managed externally Ethernet port ETH Connector RJ45 Speed 10 100 Mbit s Signals green connection LED yellow data LED RS 485 port optional RS 232 port optional Opto isolated Connector DB9 M Speed 9 6 kbit s 115 kbit s Connector DB9 M Speed 9 6 kbit s 115 kbit s USB port optional 80991 MHW GF VEDO SL 10 2012 ENG Connector type A Standard USB 2 0 35CT 70CT V70CT Ethernet FTP File Transfer Protocol COMMUNICATION Modbus TCP IP Master Slave PROTOCOLS CAN CANopen Master Modbus Modbus RTU Master Slave Type TFT touch screen with 4 wires resistive technology Dimensions diagonal 35 7 Resolution in pixels 320 x 240 QVGA 7OCT 800 x 480 WVGA V70CT 480 x 800 Display area L x H 70 x 52 5 mm OCT 152 4 x 91 4 mm V7OCT 91 4 x 152 4 mm imi Colours 262 000 Brightness 400 cd m 240 cd m Contrast 400 1 1000 1 Backlighting White LEDs duration 50 000 hours 25 C Visual angle Horizontal 60 7OCT and V70CT 85 in all Vertical 45 60 directions CONFIGURATION ELEMENTS Procedure software access 16 position dial CONTROL Keypad optional 6 programmable function 10 programmable function ELEMENTS ei buttons buttons Type ARM9 MICROPROCESSOR Frequency 40
15. hernet connection is active Yellow Data LED transferred Power The Integrated Controller and Operator Panel must be con nected to a 24 Vdc power supply unit The same 24 Vdc power supply can feed several devices controller and CAN IO modules Make sure that the current issued by the power supply is higher than the total maximum current absorbed by all the devices connected 230 Vac ISIN Figure 10 GF_VEDO SL power 13 Flashing signals that data is being A high speed transfer could make the yellow LED appear permanently on Considering that the device has no switch it is necessary to install one before it with a protective fuse The switch has to be positioned in the immediate vicinity of the device and be easy for the operator to reach For the 24 Vdc power supply use a separate line from that used for electromechanical power devices such as relays contactors solenoids etc If there are considerable changes in the mains voltage use a voltage stabiliser Near to high frequency generators or arc welders use ade quate grid filters Connect the power cables to the power connector Fit the cylindrical nucleus in ferrite supplied with the product as close as possible to the device to limit the susceptibility of the device to electromagnetic disturbance figure 11 The 24 Vdc power cables must follow a separate route from the power cables of the system or the
16. llows a return to the Main Menu The CANopen Modbus TCP and Modbus RTU buttons allow access to information relating to the various commu nication protocols The System Message button allows access to system in formation The screen directly shows the versions of Bootloader Firmware Filesystem and Runtime CANopen CAMopen Node Status Configured Mo Present operational No Met Status Boot up slave Miss counter Emergency Counter Code GoGh Add Gh ah code Gh Gh Gh Register oooh This screen shows the node number of the Integrated Con troller and Operator Panel for the CANopen protocol and in formation on the status of the CANopen protocol Emergency information defines the number of times that the node has shown the state of emergency The HOME button in the top left corner allows a return to the Main Menu while the BACK button returns to the nfor mation screen 80991_MHW_GF_VEDO SL_10 2012_ENG Modbus TCP Modbus TCP Ho Mo Present operational No Wet Status Disconnected Miss counter IF Address This screen shows the Node number of the Integrated Con troller and Operator Panel for the Modbus TCP protocol and information on the status of the Modbus TCP protocol The HOME button in the top left corner allows a return to the Main Menu while the BACK button returns to the nfor mation screen Modbus HTU Modbus RTU Ma Wo Present operational No Wet Status Disc
17. m architecture 80991 MHW GF VEDO SL 10 2012 ENG Technical data The integrated Controller and Operator Panel allows the complete management of automation Available in 3 versions 6 models and equipped with a po werful 400 MHz processor It is destined mainly to operate in an industrial environment on the control panels of production process machines or processes The operator interacts through a colour touch screen Depending on the model the size of the screen is 3 5 or 7 wide As an option the device can be equipped with programma ble function buttons Thanks to its numerous communication ports Some of which are optional it is possible to connect a wide range of devices to the controller such as computers barcode rea ders USB sticks modems printers etc and connect it to an Ethernet network The remote input and output modules CAN IO are con nected by bus to the CAN port CANopen Other CANopen standard compliant devices can also be connected to the bus 35CT 70CT V70CT Operating voltage 24 Vdc 25 Absorbed current at 24 Vdc 300 mA max 350 mA max Dissipated power 7 5 W max 8 5 W max Protections Protection for polarity inversion Short circuit Connection 3 pole polarised extractable connector Screw terminals max wire section 2 5 mm BACK UP BATTERY Type Rechargeable Li Al 3 V 65 mA h type ML2032 non replaceable Duration 10 y
18. machine 80991 MHW GF VEDO SL 10 2012 ENG FERRITE 24 Vdc 25 350 mA max Figure 11 GF_VEDO SL power connection Attention make sure that the earth connection is efficient A non existent or inefficient earth con nection can make the operation of the device unstable due to excessive environmental In particular check that e the voltage between ground and earth is lt 1 V e the ohm resistance is 6 Q CAN Connect the cable for the CAN field bus CANopen protocol The CAN bus connects the various CAN devices such as the CAN IO modules to the Integrated Controller and Ope rator Panel Considering that the CAN port is opto isolated it is not ne cessary to disconnect the power to the device before con necting it For the wiring of the line use an approved cable Fasten the cable connector to that of the controller with the appropriate screws EC peg Description CAN Low CAN Ground mass Earth CAN High CAN 80991 MHW GF VEDO SL 10 2012 ENG A 6669969 S Ji JQ JU J Q J L J Figure 12 CAN bus line termination The line termination is not fitted in the controller It is therefore necessary to fit two terminations resistor 120 Q 14 W 5 at the ends of the CAN bus as shown in figure 12 Note If the last device of the CAN bus is a CAN IO module it is possible to activate the termination in the module with the appropriate
19. n 1 and 12 mm thick to allow the fastening of the device with the terminals supplied e if the use of the USB transfer cable is envisaged read the notes on its installation first GF VEDO SL 35CT GF VEDO SL V70CT GF VEDO SL V70CT Figure 4 Panel hole dimensions for GF VEDO SL Protection against infiltrations of water The Integrated Controller and Operator Panel offers first of all a degree of protection of IP65 It is therefore possible to install the device in particularly dusty environments or areas subject to splashes of water without problems e the compartment in which the device is housed also has to be dust and waterproof e the panel on which the device is installed must be per fectly smooth and flat on the front e the hole in the panel must scrupulously respect the di mensions indicated e the device has to be fastened tightly to the panel to allow the gasket fitted at the back to ensure water tight ness Vibrations The Integrated Controller and Operator Panel can support vibrations up to 150 Hz e from 5 to 9 Hz sinusoidal 3 5 mm constant e from 9 to 150 Hz sinusoidal with acceleration equal to 1G Should the device be mounted on a support that exceeds these limits it is necessary to envisage a system for the su spension and mitigation of the vibrations 11 Minimum spaces for ventilation The temperature of the compartment that houses the Inte grated Controller a
20. nd Operator Panel must not exceed 50 C Figure 3 Free spaces for ventilation shows the mini mum free distances recommended in the installation of the device in a closed compartment Positioning The Integrated Controller and Operator Panel has to be po sitioned in order to guarantee the following conditions e the screen must not be directly lit by the sun or particu larly bright light sources e If necessary screen direct rays using an antiglare shut ter for example e there must be no sudden temperature changes e there must be a low explosion risk it can be connected to elements that operate in environments with a hazar dous atmosphere flammable or explosive only through appropriate and suitable types of interface compliant to the safety standards in force e low presence of magnetic fields 80991_MHW_GF_VEDO SL_10 2012_ENG Figure 5 GF_VEDO SL admitted angulation Figure 6 Position and angulation The angulation of the controller must be between 45 and The angulation to choose also depends on the position of the 120 as shown in figure 5 controller compared to the operator as shown in figure 6 Fastening to the panel Fit the die cut rubber seal in the back of the Integrated Con With GF VEDO SL 70CT and GF VEDO SL V70CT fit the two troller and Operator figure 7 metallic brackets supplied into the special housings on the The seal supplied as standard is essential to guarantee short sides and fas
21. nd built in Operator Panel the operator must receive full training in the proce dures of operation emergency diagnosis and maintenance of the system Printing conventions used in the manual Pay attention to the use of the following symbols Highlights particularly important information which influences the correct operation of the product or of safety or an instruction which must absolutely be followed staller or the user due to the presence of dange rous levels of voltage Highlights a risk condition for the safety of the in 80991 MHW GF VEDO SL 10 2012 ENG Glossary CAN CANopen Work cycle Data logger Duration of settlement Encoder Electric resistance extensometer Ethernet FLASH FRAM FTP LSB LSS Modbus Opto isolated PID PLC PWM RAM Controller Area Network also known as CAN bus is a standardised bus that enables the devices to communicate with each other CAN communication protocol Protocol specification for devices used in automation systems Fraction of time that represents the active state of a device circuit etc in relation to the total time considered Enables the storage of information for fi ling records or further processing Time required for the output value to reach and remain above 90 of the final value Rotative position transducer Sensor that transforms small dimensional deformations of a body subject to me chanical or thermal s
22. nnection can be used successfully over long distances and in environments characterised by considera ble disturbance The maximum length of the cable depends on the transmis sion speed as shown in figure 14 10m 10 kb s 100 kb s 1 Mb s 10 Mb s Max data transmission speed with AWG24 cable Figure 14 RS485 max transmission speed 80991 MHW GF VEDO SL 10 2012 ENG Set up program When no application program has been uploaded onto the Integrated Controller and Operator Panel or when the dial is positioned on F the following happens 1 The Gefran logo appears on the screen GEFRAN 2 The operating system is loaded this takes about 1mi 3 The Main Menu of the set up program appears The set up program allows configuration of the device and to obtain information on it The configurations to be carried out when using the control ler for the first time are 1 Regulation of the current date and time 2 Calibration of the touchscreen display 3 Uploading of the application program When uploading an application program onto the controller the set up program is no longer shown To access the set up program again after uploading an ap plication program onto the Integrated Controller and Opera tor Panel proceed as follows 1 Switch off the controller 2 Shift the con
23. onnected Miss counter Fisical number node This screen shows the Node number of the Integrated Con troller and Operator Panel for the Modbus RTU protocol and information on the status of the Modbus TCP protocol The HOME button in the top left corner allows a return to the Main Menu while the BACK button returns to the nfor mation screen System Message Fault FALSE Fault address This screen shows useful information in the case of malfun ctions Reset after watchdog signal indicates whether the con troller restarts automatically after the program has been blo Cked Last Fault indicates when the last malfunction occurred Fault address indicates the address of the application pro gram code which manifested the malfunction PLC Loaded shows and signals the correct upload of the PLC software HMI Loaded shows and signals the correct upload of the application program The HOME button in the top left corner allows a return to the Main Menu while the BACK button returns to the nfor mation screen Uploading the application program To upload the application program onto the Integrated Con troller and Operator Panel proceed as follows 1 Connect the controller to a PC using a crossover Ether net cable 2 Open the Network screen of the set up program di sable the DHCP and manually set an IP address e g 192 168 010 002 Run the GF Project LX program on the PC Click the Open code prj button
24. s in the position chosen should not exceed 2 mm SD Card The SD Card slot is optional and allows use of the SD Card mass memories to store data and applications The SD Card can be used and removed at will Before removing it make sure that there are no writing ope rations in progress RS232 The RS232 port is optional Considering that the RS232 port is not insulated it is necessary to disconnect the power to the Integrated Controller and Operator Panel and to the de vice to be connected before connecting them The connection cable must be screened and not exceed a length of 5 metres Tighten the cable connector to that of the controller using the special screws 0000 O 0006 i Description Signal Flow Data Carrier Detect Input Received Data Input Transmitted Data Output Data Terminal Ready Output Ground Mass Data Set Ready Input Request To Send Clear To Send Output Input Ring Indicator Input 15 RS485 The RS485 port is optional Considering that the RS485 is opto isolated it is not neces sary to disconnect the power to the Integrated Controller and Operator Panel and to the device to be connected be fore connecting them Tighten the cable connector to that of the controller using the special screws Pend Description Data Ground O O TINIO Ci C n The RS485 co
25. ten them in place with the screws figure IP65 rated protection Figure 7 Assembly of seal metal bracket and terminal connection Fit the Integrated Controller and Operator in the panel con nect the 4 terminals supplied to the device and tighten the There are 4 positions in which to connect the terminals two screw until the device is fastened tightly to the panel per side Com gs c UL d m ewe ono j DIO eoo DUO DUO DDO GF VEDO SL 70CT GF VEDO SL 35CT GF VEDO SL V70CT Figure 8 Positions available for fastening terminals 80991_MHW_GF_VEDO SL_10 2012_ENG 12 Integrated Controller and Operator Panel Connections EEEE Inputs ports and signals GF VEDO SL 35CT GF VEDO SL 70CT GF VEDO SL V70CT Figure 9 GF_VEDO SL connector position Description Input power 24 Vdc 25 Connector indicator Pull out polarised terminal block CAN Port DB9 M D sub 9 pin male Ethernet Port 10 100 Mbit s RJ45 USB Port SD Card Slot USB Type A optional optional RS232 Port DB9 M D sub 9 pin male optional Insulated RS485 Port DB9 M D sub 9 pin male optional Green Link LED Permanently on signals that the Et
26. tress in changes of electric Standard for local networks LAN Non volatile memory in the solid state Non volatile RAM faster than the Flash memory File Transfer Protocol Allows the upload and download of data files between the controller and other digital devices Least Significant Bit It defines the minimum resolution of a me asurement Layer Setting Services Open serial communication protocol de facto standard in communication betwe en industrial electronic devices Modbus RTU is the most common imple mentation of this standard Modbus TCP IP is that specific m for Ethernet networks Circuit configuration which through an electronic component called an opto iso lator allows the transferral of a signal between two circuits while maintaining galvanic separation Regulation algorithm Programmable Logic Controller A digital computer specialised in the ma nagement of industrial processes Pulse Width Modulation Technique for controlling power towards electric devices Random Access Memory Electronic memorising device which ena bles the reading and writing of data 80991_MHW_GF_VEDO SL_10 2012_ENG RS 232 RS 485 SD Card SDRAM Strain gauge USB Standard which defines a low speed se rial transmission interface for the exchan ge of data between digital devices such as modems Standard at physical level for serial con nection with 2 wires Card for memorising large amoun
27. troller dial to position F figure 15 GF VEDO SL 35CT GF VEDO SL 70CT GF VEDO SL V70CT U La e 32 L es Ge DC JC Jl Figure 15 GF VEDO SL Dial 3 Switch the controller on again After the initial start pha se the main menu of the set up program appears 4 Operate as for the set up program and then switch off the controller 80991 MHW GF VEDO SL 10 2012 ENG 5 Shift the controller dial to its previous position 6 Switch the controller again After the initial start phase the application program screen appears Main Menu MAIN MENU Configuration Information Exit System Setup ver GL GG The version of the set up program installed appears in the top right corner The Configuration button allows access to the device con figuration procedures The Information button allows access to information on the firmware and communication protocols installed The Exit button allows a return to the application program if installed Configuration CONFIGURATION Network Display Touchscreen Calibration Time e 00 Date D7 oy Save The HOME button in the top left corner allows a return to the Main Menu
28. ts of di gital data Synchronised access RAM See Electric resistance extensometer Universal Serial Bus serial communica tion and feeding standard created to con nect peripherals to computers Overview of the solution and functionalities GF_VEDO SL is the complete process and automation con trol solution which allows sequence control process mana gement programming and display of data and connectivity with a single modular system To this end a combination of technological functions such as the management of PWM fast counters data filing by data logger temperature PID data export via FTP ena bling the rapid creation of applications is made available Controller and Operator Panel integrated into a single devi ce complete with PLC embedded run time available with a 3 5 or 7 wide display the latter in either a horizontal or vertical version Architecture Modbus TCP Modbus RTU p cla in dicas cR mmm 1 RS485 lt RS232 CANopen Thanks to its flexibility and ease of use can be used in a va riety of sectors and for numerous process and automation process controls such as e the wood industry gluing etc packaging packing labelling etc food industry pasteurisers etc chemical industry autoclaves etc metal working washing etc plastic working dryers coolers etc Ethernet USB SD card Figure 1 Syste
29. ve the changes made When the new time has been saved the underlining disappears Attention the controller does not automatically update the time when the clocks go back forward The Save button memorises the new time and date and the Cancel button cancels the changes and maintains the pre vious time and date Network NETWORK IP Address fon foon pon ooo Subnet Mask faon joon poo pao Enable DHCP Save cancel On this screen it is possible to know and set the IP IP Ad dress and the Subnet Mask of the Integrated Controller and Operator Panel Selecting Enable DHCP the controller obtains the IP ad dress from a DHCP server connected to the network other wise it uses the IP address saved by hand The Save button memorises the new configuration and the Cancel button cancels the changes and maintains the pre vious configuration parameters The HOME button in the top left corner allows a return to the Main Menu while the BACK button returns to the Con figuration screen 14 Display DISPLAY Brightness 0 0 100 MEM Screen saver timeout D seconds 0 600 AMEN Save Cancel On this screen it is possible to regulate the brightness and the screensaver timeout To regulate the Brightness of the screen use the and buttons The 100 value set in the factory is ideal for most situa tions To regulate the Screen saver timeout use the and but tons 120 seconds set in
30. window at the bottom 14 Click the Open GF Project LX page button and wait for the page editor to open 15 Open the page application selecting the OPEN page menu 16 Select the page required the file extension is PAJX from the list and click the Open button 17 Select gt Communication settings from the Project menu 18 Select the GDB protocol in the Device Link Manager Config window that opens 19 Click the Properties button The Gdb Config Win dow opens Select the TCP IP protocol from the Port dropdown menu and enter the P address indicated at step 2 of the procedure in the IP address box 20 Click the OK button and then press OK again 21 Transfer the program selecting gt Download Project from the Project menu 22 n the bottom left corner of the Output panel there is a list of the results of the actions performed and the first page of the program uploaded appears on the screen of the Integrated Controller and Operator Panel 23 Remove the Ethernet cable To upload a new program onto a controller that has already been programmed follow the same procedure 80991 MHW GF VEDO SL 10 2012 ENG Maintenance SSS ee Integrated Controller and Operator Panel To clean the screen use a slightly damp soft cloth Do not use chemical or abrasive products Disconnect the power supply before cleaning the Controller Diagnostics Integrated Controller and Operator Panel See the System Message screen of
Download Pdf Manuals
Related Search