KGNPRO19VD USER MANUAL
Contents
1. Check the picture contracting and brightness settings Normal picture but no sound Check the volume Sound muted Press the MUTE button Try another channel the problem may be with the broadcast Are the audio cables installed properly The remote control does not work Check to see if there any object between the product and remote control Causing obstruction Are the batteries installed with correct polarity to to Correct remote operating mode set TV VCR etc Install new batteries Power is suddenly turned off Is the sleep timer set Check the power control settings Power interrupted Unplug the TV for one minute then reconnect it and try again Picture appears slowly after switching on This is normal the image is muted during the product startup process Please contact your service center if the picture has not appeared after five minutes No or poor color or poor picture Adjust the color in menu option Keep a sufficient distance between the product and the VCR Try another channel the problem may be with the broadcast Are the VIDEO cables installed properly Horizontal vertical bars or picture shaking Check for local interference such as an electrical appliance or power tool Poor reception on some channels Station or cable product experiencing problems Tune to another station Station signal is weak reorient antenna2. PVR File System For DTV only To check the USB connected and provide with the recording function Aspect Ratio Changes the aspect ratio in sequence Auto 4 3 16 9 Zoom 1 Zoom 2 gt Just Scan Just Scan is panoramic display so black edging may appear according to the data rate Blue Screen Set to On blue screen displays set to Off blue screen disappears First Time Installation Set relevant options including OSD Language and Channel Tuning Please refer to P8 for concrete operations Reset To set all the options to factory setting Set this option only when it is necessary Software Update USB To update software by using USB PVR File System For DTV only Firstly insert USB device to the SERVICE port and press A button to choose Check PVR File System then press OK button to start checking This process needs some seconds If it finishes the word SUCCESS will be shown after Check PVR File System and the speed will be shown on the menu as well Now you can record and save the DTV programme Note Hard disk with self contained power is suggested to be used 14 LED rW Recorded List Programme 1 Delete ORO SOURCE Input Source ATV AV RE Component DAB HDMI Press button on the remote control to start recording the programme Q mark appears at the top left corner of the TV screen and the title bar appears at the bottom which includes
3. USB port O ON OO FBP ON Insert DVD with Label to the Back O1 LL CID rW TV Terminal connections PC SERVICE COAXIAL DC IN 9 RF 75Q L R VIDEO COAL PrCr PbiCb Y AUDIO VGA HDMI 7 i a gm 1 6 5 4 2 1 DC 12V power input 2 Service input Available for performing PVR function or updating the firmware 3 HDMI input 4 VGA input 9 PC audio input 6 Component video input terminals Y Pb Cb Pr Cr 7 Coaxial audio signal out plug 8 Composite video amp audio input terminals AV 9 Antenna input 75 Ohm VHF UHF 10 Headphone output LGD rW 6 Connecting to external devices Connecting external devices to your LCD TV HDMI The rear of TV 95959 YPbPr n AV Q RF 7 50 L R VIDEO epos Pr Cr Pb Cb Y Coaxial Cable Digital Audio Input C a e e 1 L AUDIO R COAXIAL e e J AUDIO OUTPUT HDMI Power Amplifier ui E D Digital Audio System Notes VGA use a common PC AUDIO in LED rW 7 The OSD menus Menu Setup TV Firsttime installation wizard If this is the first time switch on the First time installation Please select an OSD Language menu will appear on the display Espa ol Italiano Language Press A lt 4 button to select the desired language Deuts
4. button cannot work Hotel Mode Set the hotel mode function 12 LGD rW Set Password You can change the password by entering the old and a new password and then re entering it to nter password E m confirm the new one Please enter new password irt Clear Cancel gt Block Program Press Green button to lock the desired channel press it again to unlock it Block Program 350 DVB 4 1 352 DVB 4 1 353 DVB 4 1 DTV Parental Guidance For DTV program only Press A button to set the parental guidance level Parental Guidance BLOCK ALL G PG 13 LGD rW Check PVR File System Format Free Record Limit O Ne Start Hotel Mode Have the priority than other options below To set below options this item must be set to On firstly Source Lock To set the input source item which you want to be locked Default Source To set the default input source when you open the TV main unit Default Prog To set the default ATV channel program when you power on the TV Max Volume To set the maximum volume value Clear Lock To clear all the locks 6 SETUP MENU The image on the left depicts the setup menu The definition of each option OSD Language Changes the OSD language as English Spanish gt French gt Italian German TT Language Set the teletext language Hearing Impaired For DTV only Changes the hearing impaired mode to On or Off
5. control can be used to display the content of previous or next page Number buttons on the remote control can be used to get to a certain page Press the red green blue and yellow button on the remote control the page of relevant color displayed on the lower part of the screen will be displayed SIZE press it once to enlarge the content on the upper part of the page and press it the second time to enlarge the content on the lower part of the page and the third time to resume normal display of all the contents on the page REVEAL Press it once to display the hide text press it again to close the display of hide text INDEX press it once to display the index for all the teletext page FAST TEXT For possible future reference The RED GREEN YELLOW amp CYAN buttons are used for quick access to color coded pages transmitted by FAST TEXT broadcast Example RED selects CITY INFORMATION CYAN selects TRAVEL INFORMATION GREEN selects WEATHER INFORMATION YELLOW selects TV PROGRAMMING 4 LGD rW 5 LCD TV panel overview TV Control Panel OOWOODOO O VOL VOL CH CH MENU SOURCE POWER Power indicator Remote sensor Volume adjusting Channel selecting Main menu display Selecting exterior signal input Power on off button PLAY PAUSE button OPEN CLOSE button 10 SD MMC MS card slot 11
6. size of your television screen you may see black borders above and below the picture 16 9 Wide Choose this setting if you have a widescreen television NOTE Playback screen size may vary according to the discs contents For discs with 4 3 contents using any mode would only display a 4 3 screen Screen ratio selection should be according to the connected TV Display aspect ratio Password The default setting is locked No Rating selection or change password could be done To edit the Rating setting please enter default password 0000 by numeric button then press OK button to confirm To change password input any 4 digit number when the lock is unlocked Once the 4 digit number is entered that will be your new password Rating Playback for some discs with rating you can select the rating setting according to your preference Rating restriction divided in eight different category from KID SAFE to ADULT 23 EJ a SYSTEM SETUP DIUI 1 KID SAFE Only editable when password is unlocked And only can SCREEN SAVER 2G function when password is locked It does not however aS Mos reset either the Password or the Rating setting PASSWORD 4 PG13 RATING 5 PG R POWER RESUME 6R DEFAULT 7 NC 17 Default Setting SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD NITE POWER RESUME DEFAULT Press OK button to restore factory default Press DVD SETUP button to en
7. the recording information You can press lt gt button to select one function you want to run then press OK button to operate Press EXIT button to hide the title bar You can press relevant buttons on the remote control to perform such functions directly Press REC LIST button to display the recorded list Press A Y button to select the desired one then press OK button to play the recorded programme Press Red button to delete the current list Press Green button to show the list s information Press INDEX button to sort all the programs according to Programme Channel or Time 1 Press SOURCE button to change from ATV to other available inputs 2 Press A button to select signal source 3 Press OK or button to confirm 4 Press EXIT button to exit signal souce menu 15 DVD Operation LED rW Basic operation 1 Turn ON and OFF the DVD function Turn on the LCD TV and then press SOURCE repeatedly to select DVD mode 2 Insert Disc to DVD Insert the Disc to the Disc slot Data side of the disc has to face towards front of the unit the player will load the disc automatically there will be an on screen indication CLOSE then READ After loading the disc content it will switch to play mode automatically If the disc is already placed inside the disc will be read automatically NOTE For some discs after loading the content of the disc need to press bil or select from the disc menu to start
8. 24 MENU Language iq bo LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG ENGLISH GERMAN SPANISH FRENCH ITALIAN Use navigation buttons to select the MENU LANG setup icon press OK button to confirm There are 5 languages for you selection press 4 w buttons to toggle between different languages Press OK button to confirm Speaker Setup Downmix Use the A wbuttons to adjust the Downmix setting 25 SS Setup Dynamic Range LJ a O DIGITAL SETUP Dual Mono UJ s O DIGITAL SETUP DYNAMIC RANGE 4 Vi i IVE 2o E zi WO NTO ss MIX MONO MONOL Moving the dynamic range switch changes the compression of the audio output signal the lower the compression the louder the volume will be You can select four different audio output STEREO MONO L MONOR MIX MONO The audio out description of these Selections is shown in the table below LEFT SPEAKER RIGHT SPEAKER STEREO L STEREO R L MONO L MONO L MONO R MONO L MONO R MONO 26 LGD rW Trouble shooting Before contrast the service technician perform the following simple checks If any problem still persists unplug the LCD TV and calling for assistance PROBLEM POSSIBLE SOLUTION D No sound and picture Check that the main plug has been connected to a wall outlet Check that you have pressed the POWER button on the front of the TV set
9. CD VCD CD CD G HD CD and Mp3 discs USB CARD When playing DVD VCD CD disc press the A B buttonto repeat a certain content Press the A B button on the start point A and the ending point B to select the repeat part Press the A B button a third time to cancel the A B repeat function and return to normal play 11 Volume for DVD Super VCD VCD CD CD G HD CD and Mp3 JPEG discs USB CARD Press VOL VOL buttons to adjust the output volume MP3 JPEG USB CARD Playback After loading the MP3 JPEG USB CARD disc it will start to scan for the stored MP3 JPEG USB CARD folders Then will firstly display the MP3 contents automatically and start to play the first file highlighted file Screen as follow Highlight file for current playback Scroll bar to view Display current next page MP3 playback function Display current MP3 playback function PPPEE PERE rr i Aa hs Buttons for switching between MP3 and JPEG playback function Using the navigation buttons to check you favorite folder and playback the first file or move to the your favorite file NOTE Press lt gt buttons to move the highlight to folders documents or mode selection Press numeric buttons to select the contents directly For number over 10 press button first e g File number 15 press then 1 and 5 When playing MP3 files there is no picture displa
10. Check for sources of possible interference Lines or streaks in pictures Check the antenna Change the direction of the antenna No output from one of the Repeats Adjust balance in the menu option J 2f LGD rW NOTE There is a problem in VGA mode Only VGA mode applied e PROBLEM POSSIBLE SOLUTION S Adjust resolution horizontal frequency or vertical frequency The signal is out of range Check it whether the signal cable is connected or loose Check the input source Vertical bar or stripe on back ground amp Horizontal Noise amp lncorrect position Work the auto configure or adjust clock phase or H V position Screen color is unstable Check the signal cable Reinstall the PC video card or single color J Maintenance Early malfunctions can be prevented Careful and regular cleaning can extend the amount of time you will have your new TV Be sure to turn the power off and unplug the power cord before you begin any cleaning Cleaning the screen 1 Here s a great way to keep the dust off your screen for a while Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent Wring the cloth until its almost dry and then used it to wipe the screen 2 Make sure the excess water is off the screen and then let it air dry before you turn on your TV Cleaning the cabinet To remove dirt or dust wipe th
11. F ELECTRIC SHOCK DO NOT The exclamation point within an equilateral triangles is intended REMOVE COVER OR BACK REFER SERVICING TO to alert the user to the presence of important operating and AUTHORISED SERVICE PERSONNEL maintenance servicing instructions in the literature accompanying the product WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE Always power this product from an outlet with the same rating voltage and frequency as indicated on the rating label on the back of the product if this product has been damaged including cord or plug take it to an authorised our service technician for inspection and if necessary repair Turn off and disconnect the power cable before cleaning or storing this product Ensure this product does not get wet Only use the A C power adapter supplied with your product Do not place naked flames such as lit candles on or near the product Do not place objects filled with liquids such as vases on or near the product Do not install this product on top of other electrical equipment or on uneven surfaces Do not use or store this product in a place where it is subject to direct sunlight heat excessive dust or vibration Do not use this product with wet hands Do not clean this product with water or other liquids Do not block or cover the slots and holes in the product Do not push foreign objects into the
12. Please make sure when inserting the Disc the Data side of the disc should be facing you When inserting the Disc incorrectly you may damage the DVD mechanism 3 Play the DVD According to the disc content the disc menu will display for your selection When playing the disc you may use PI button to toggle between Play and Pause mode This product also supports Menu Title Sequential and Program playback 4 Menu playback for DVD super VCD and VCD 2 0 discs Press MENU button For DVD discs the screen will display the DVD Disc Menu Root Menu For Super VCD amp VCD2 0 discs the screen will display the Super VCD VCD2 0 Disc Menu PBC OFF Press the D MENU button to display the PBC status Playback the Super VCD amp VCD2 0 discs the default PBC status is ON For DVD discs use the navigation buttons to select and Play the highlighted contents For Super VCD amp VCD2 0 discs use the numeric buttons to play your favorite content directly NOTE PBC should be OFF Press OK or PI button to start from the highlighted content Return to the Root Menu when playing the disc For DVD discs press D MENU to display the Disc Menu For Super VCD amp VCD2 0 discs when PBC is ON press D MENU to display the Disc Menu STOP Press W button once to stop Press pil button to resume from where you stopped Press lll button Twice to stop Press bil button to start from beginning In order to protect the disc press W button then pres
13. The image on the left depicts the time menu The definition of each option Clock For DTV only Display the current system time Its not available Time Zone For DTV only Press W A lt 4 gt button to set the proper time zone according to your region Sleep Timer Set the sleep timer to put automatically the TV in standby mode Timer can be selected as 10 20 30 60 90 120 180 240 and 0 Min Off You may select the sleep timer by pressing SLEEP button repeatedly Auto Standby The options are Off 3 H 4 H 5 H You can set the main unit to turn off automatically when there is no signal in a preset time 1 minute while the input source is PC OSD Timer Changes the OSD timer as 5 S 10 S 15 S 20 S 25 S 30 S 5 LOCK MENU The image on the left depicts the lock menu The definition of each option Lock System Press A button to select Lock System then press or OK button to select On or Off which enables or disables below lock functions Password Enter the default password 0000 to go to the LOCK function menu if you have set Lock System to On Set Password Set a new password Block Program Add or release a lock to some special program When watch a locked program a dialogue box appears You should enter the correct password The initial password is 0000 Parental Guidance For DTV program only Set the parental guidance level Key Lock Set to On the keypad on the main unit except POWER
14. adjusting button DVD stop button DVD play pause button Teletext on off mix button DVD rewind Teletext cancel button Disc menu Teletext hold button DVD forward Teletext reveal button DVD goto RED button DVD slow GREEN button Sleep function button NICAM function button Audio language select button Numeric buttons DVD title Return channel button Menu button Navigation buttons Up Down Left Right Confirm button Menu exit button Channel select button Display mode select button DVD open close Auto adjust button in PC mode Recording button DVD setup menu Electronic program guide button Subtitle button DVD previous Teletext size button DVD zoom in out Recording list Teletext index button DVD next Teletext subpage button DVD A B repeat BLUE button DVD repeat playback YELLOW button x If there is light around the TV the remote control may fail or work abnormally x If long time not to use the remote please remove the battery LGD rW 4 Remote control functions POWER Power on off button press once to turn the TV on and press again to turn the TV off P MODE Picture mode button setting the picture mode S MODE Sound mode button setting the sound mode I Il Press the I II button to choose a different audio channel SLEEP Slee
15. bove functions may vary due to different DVD disc s structure 3 Forward Backward for DVD Super VCD VCD CD CD G HD CD and Mp3 USB CARD While playing the disc you may use forward or backward function There are 4 speeds for forward Press gt gt button to toggle between different speeds in sequence FORWARDx2 FORWARDx4 FORWARDx8 FORWARDXx20 Play While in backward you may press PI to resume normal speed For CD HD CD MP3 backward also has audio output only for BACKWARDx2 For DVD discs if backward to first title chapter it will start from the beginning For Super VCD amp VCD discs in PBC ON status if backward to the first track it will start from the beginning NOTE During Forward or Backward the sound will be off 4 Pause for DVD Super VCD VCD CD CD G HD CD and Mp3 JPEG discs USB CARD FOR CD CD G HD CD amp MP3 JPEG discs press PI button to pause press I button to resume FOR DVD Super VCD VCD discs press bil button to pause press I button to resume 5 Repeat for DVD Super VCD VCD CD CD G HD CD and Mp3 JPEG discs USB CARD Press REPEAT button once to display the current repeat mode For Super VCD VCD CD CD G HD CD discs while playing in sequent you may use the repeat playback There are 2 repeat modes press REPEAT to toggle between different modes in sequence REPEAT OFF REPEAT 1 REPEAT ALL For DVD discs you may setup the repeat playback mode There are 3 repeat m
16. ch ciens then press OK button to enter the Channel Tuning ok screen The original language of this TV is English Channel Tuning Channel Tuning The TV will start searching channels automatically from the lowest frequency When it finds a station it will store this in the first location and move to the next When auto AUA tuning is completed the TV will display the first station 0 Programme found 0 Programme Press MENU or EXIT button to skip or cancel the tuning 0 TV LLLLLTTTTTTTPTPPDm process Please press MENU key to exit LGD rW Menu Operation Under TV Input CHANNEL h t Channel Tuning 0 Programme 0 Programme 0 Programme 0 TV PT TTT TTT TTT TTT TT Please press MENU key to exit DTV Manual Tuning Press OK to search Bad Freq 205 50 Mhz Good BRE EERE RRR ERR RRR RRR eee eee 1 CHANNEL MENU The image on the left depicts the channel menu The definition of each option Auto Tuning Press A W button to this position then press or OK button to enter auto tuning of both ATV and DTV channels DTV Manual Tuning Press 4 button to this position then press or OK button to enter DTV Manual Tuning It will scan current DTV Digital TV program within a frequency range accurately and store the result manually ATV Manual Tuning Press 4 button to this position then press or OK button to enter ATV Manual Tuning Programme Edit Press A Y button to this position then
17. e cabinet with a soft dry lint free cloth Please be sure not to use a wet cloth Extended Absence A If you expect to leave your TV dormant for a long time such as a vacation it s a good idea to unplug the power cord to protect against possible damage from lightning or power surges 28 LGD rW Specifications Panel Features Screen Size 18 5 inch Active Area 409 8mm H X 230 4mm V Aspect Ratio 1366 X 768 250 cd m 1000 1 170 H X 165 V 0 3mm H X 0 3mm V 16 7M Panel Resolution Brightness Contrast Ratio Viewing Angle Dot Pitch Maximum Colour Response Time Black White R amp D OSD Languages o co C1 3 7 English French Spanish German Italian TV Function Broadcast System PAL DVB T Receiving Channel Video Standards Supported NTSC PAL PAL DVB T Audio Output Maximum Audio Output 2 3W 4 Ohm Input Connections TV Input Digital tuner Analog tuner 1 RF 75 Ohm YPbPr Input VGA Input AV Input L R Audio Input For YPBPR AV PC Audio in HDMI Input Service Input Composite Video input Antenna RF 1 Component 3pin 1 15 pin D Sub 1 Composite Yellow RCA 1 White RCA Red RCA Stereo Mini Phono Jack Input 3 5mm 1 19 pin VGA Resolutions Supported 640x480 60Hz 800x600 60Hz 1024x768 60Hz 1360x768 60Hz Power AC 100V 240V 50 60Hz DV 12V 4A Power Consumption 45W TV Power Input N cO
18. er VCD discs Press the SUBTITLE button once to display current subtitle Press again to toggle between different subtitle modes in sequence NOTE For Multi languages subtitle DVD amp Super VCD discs press the SUBTITLE button to select your favorite subtitle language A B When playing DVD VCD CD disc press A B button to repeat a certain contents Press A B key on the start point A and the ending point B to select the repeat part Press A B the third time cancel the A B repeat and return to normal play DVD SETUP Press DVD SETUP button to open setting menu AUDIO Press AUDIO button to choose different audio channel TTX press TTX to enter teletext state and display teletext page If want to display image and teletext page at the same time press this button again If want to exit teletext state press this button again When teletext page is displayed on the screen you can select relevant function by using the remote control Press the TTX to start and exit Teletext SUBPAGE is refer to the subpage of teletext page i e subcode page When it is pressed the screen display the requirement of subpage code entry If there is no subpage it will not be displayed In most case there is no subpage HOLD press it once to keep the display of the page and press it again to exit hold state CANCEL do not display the content of the page but only the channel image Press it again to display the content of the page again or button on the remote
19. ion for JPEG discs FII When playing the disc press PLAY PAUSE once to pause Press PLAY PAUSE again to return to normal play B When playing DVD SVCD VCD CD disc press STOP once the unit will memorize the previous ending point Press PLAY PAUSE button to go on the play Press STOP for the second time to stop the play and end the memory gt gt Press button for quick forward search 44 Press button for quick rewind search p gt When playing DVD disc press NEXT to the next chapter when playing SVCD CD disc press NEXT to the next track I When playing DVD disc press PREV to the previous chapter when playing SVCD VCD CD disc press PREV to the previous track Slow When playing SVCD VCD DVD discs press SLOW to select slow speed playing press PLAY PAUSE to resume normal play TITLE When playing DVD disc press TITLE to return the main title page GOTO The GOTO button lets you instantly select a title chapter or time Use the navigate buttons to highlight the digit you want to change After you entered the desired value confirm your choice with the ENTER button REPEAT press REPEAT button to repeat a title chapter track or the whole disc When playing DVD disc press REPEAT button continually the TV screen shows chapter repeat all repeat repeat cancel in turn when playing VCD CD disc the turn is track repeat all repeat repeat cancel when Playing Mp3 disc the turn is one repeat file repeat repeat all repeat cancel SUBTITLE for DVD and Sup
20. kogan KGNPRO19VD USER MANUAL IL CID rW Contents WY Safety DPC CAM VION caer cossuwenssdcandusecnesosaoenendasesdaenenansteenseneeeeanseweadoepeuenaneeeaseen 1 Main ACC OSS OC S erara rE EE m atu CER ded GEMRIM UEM TRIN MINNIE 2 RMOL COME Ol 3 Remote control HIP Iare 0 4 ee an ee a en 4 ESPERE Mo i Ne d EE m TU TEES 5 Connecting to external deVviCBS i secesoseie utere b thoro dp rto E PEE EE 0d PEU aa E bne Iden kIropRhs 7 i29 24g EE 8 pj Basic oDOrallobbusescertusd osnemqeriqe tad A AEA UE DR e 17 Supporting DYD formalaren ennaa QI NUN DEED Ub RUFEN E eme kt 18 DVD Functions operating INStrUuCtiOnsS cece cece eee cece eee e mn 19 MP3 JPEG USB CARD Playback cccccccecceceeceeee eee eneeeaeeaseasenaeeaeeneas 21 giiisredre eris no REESE 22 Iroupo SNOOUN MONTRENT T TU UU M 27 PVM UNINC saat ERRRT 28 SPec AO Sins cadres tesa iseria E AE E RETE 29 LGD rW 1 Safety precaution The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of insinuated WARNING dangerous voltage within the product s enclosure that may be RISK OF ELECTRIC SHOCK of sufficient magnitude to constitute a risk of electric shock DO NOT OPEN CAUTION TO REDUCE THE RISK O
21. lt gt button to start search Programme Edit Press A Y button to move the high lighted bar Press the colored short cut keys to do the editing operations and press MENU button to stop the editing work Note Before doing editing operations make sure the channel list is not an empty one This option has five functions 1 Press Red button to delete the current channel 2 Press Green button to rename the current channel For ATV only 3 Press Yellow button and A Y button to move the current channel For ATV only 4 Press Blue button to skip the current channel 5 Press FAV button to set the current channel to your favorite channel there will be a red heart at the behind of the channel selected If the current channel is already be one of your favorite channel press it again will set it to a normal one You can call out the channels from the Favorite List by pressing FAV button while enjoying TV program Signal Information For DTV only This menu displays signal details including Channel Frequency Quality and Strength 10 LGD rW AD Volume 30 2 PICTURE MENU The image on the left depicts the picture menu The definition of each option Picture Mode Changes the picture mode in sequence Dynamic Standard Mild Personal You may select the picture mode by pressing P MODE button repeatedly Contrast Changes the value of contrast with the key lt gt in the range of 0 to 100 Bright
22. mats NOTE Check your TV user guide for supported formats If NTSC is selected with a non compatible television you may experience interference or picture scrolling 22 Screen Saver LJ 2 O Press4 amp wbutton to select Screen Saver ON or OFF SYSTEM SETUP Press OK button to confirm TV SYSTEM POWER oem IV TYPE If enabled this function allows to continue the playback of NS T0 D a film DVD even after switch off or remove of a disk The SYN HIN Ce player stores all settings like play position or used language POWER RESUME and continues playback with these settings after the disk was DEFAULT reinserted This function will be enabled or disabled via the setup menu of the DVD player TV Type DVDs are produced in a variety of screen aspect ratios This menu enables you to select one of the three aspect ratios e 4 3 PS Normal LJ go O e 4 3 LB Normal SYSTEM SETUP e 16 9 Wide TV SYSTEM SCREEN SAVER Select the most appropriate aspect ratio for the DVD being 4 3PSIR viewed PASSWORD 4 3LB RATING POWER RESUME DEFAULT 4 3PS Normal Normal Pan and Scan is used for most normal television broadcasts and itis the default setting It has an aspect ration of 4 3 If you select this setting when viewing a DVD the picture will fill the screen but you will not see the left and right edges of the picture 4 3LB Normal Normal Letter Box will show the DVD in its original aspect ratio so depending on the
23. ness Changes the value of brightness with the key lt p gt in the range of 0 to 100 Colour Changes the value of colour with the key lt gt in the range of 0 to 100 Tint Changes the value of tint with the key lt gt in the range of 0 to 100 For NTSC signal only Sharpness Changes the value of sharpness with the key 4 in the range of O to 100 Colour Temp Changes the colour temperature in sequence Cold Normal Warm Noise Reduction Changes the picture noise reduction in sequence Off Low Middle gt High gt Default 3 SOUND MENU The image on the left depicts the sound menu The definition of each option Sound Mode Changes the sound mode in sequence Standard Music Movie Sports gt Personal You may select the sound mode by pressing S MODE button repeatedly Treble Changes the value of treble with the key in the range of 0 to 100 Bass Changes the value of bass with the key lt gt in the range of 0 to 100 Balance Changes the value of balance with the key lt gt in the range of 50 to 50 Auto Volume Changes the auto volume mode to On or Off SPDIF Mode Changes the SPDIF mode in sequence Auto Off PCM AD Switch For DTV only Press 4 button to this position then press gt or OK button to enter Press lt gt button to select the audio descriptor to On or Off as well as adjust the volume of the AD 11 LGD rW 4 TIME MENU
24. odes press REPEAT to toggle between different modes in sequent REP OFF REP CHAPTER REP TITLE REP ALL For MP3 JPEG discs while playing the disc you may use the repeat playback There are 3 repeat modes press REPEAT to toggle between different modes in sequent REPEAT OFF REPEAT 1 REPEAT DIR REPEAT ALL 6 INFO for DVD Super VCD VCD CD CD G HD CD and Mp3 JPEG discs USB CARD Press INFO button to activate the on screen roll down menu for the current Title Chapter time and other information 19 LED rW For DVD discs 2 pages Press INFO button once to display first page as shown below Disc Type Chapter Current Full Elapsed disc time TT 0 3 CH ye 00 05 45 Title Current Full Press the INFO button again to display the second page shown below Audio Language Audio Type Angle ON OFF Current Full or OFF Subtitle Current Full or OFF Press INFO button again to turn off the on screen display For Super VCD discs 2 pages Press INFO button once to display first page Disc type Track Current Full Mute status PBC status Repeat mode status Current track time Press INFO button again to display second page Audio Current Full or OFF Audio type Subtitle Current Full or OFF Press INFO button again to turn off the on screen display For CD CD G HD CD MP3 JPEG discs Press INFO button once to display first page Disc type Track Cur
25. p button setting TV power off time 0 1 9 TV channel selection button CES Previous channel button return to the previous channel watched USB SD Press the USB SD button to choose USB or SD card function FAV Press the FAV button to start the Favorite List for selecting your favorite program SOURCE Signal source selection button ATV DTV AV PC Component DVD HDMI MENU OSD menu button to enter the TV setup menu A Y UP Down Up and down button of the OSD menu To change the OSD menu items lt gt Left Right Left and right button of the OSD menu To select the OSD menu items OK Confirm button confirm all the changes and settings INFO Press the INFO button for information EXIT Press the EXIT to exit the operation VOL Volume adjusting button to increase or decrease the volume CHA Y Channel selection button to increase or decrease channel MUTE m Mute button press once to disable the audio and press again to enable the audio ASPECT Press the ASPECT button to select the picture display ratio Auto 4 3 16 9 Zoom 1 Zoom 2 Just Scan EPG Press the EPG button for detailed information about the channel AUTO Press the AUTO button to auto adjust items in PC mode 4 Press OPEN CLOSE button when power on the disc tray is pushed out Put the disc on the tray with the title faced Up Press OPEN CLOSE again to close the disc tray and the unit starts playing automatically Without auto play funet
26. press gt or OK button to enter Programme Edit screen You can do such editing operations as delete rename move skip sign cancel the skip mark and fav add delete to the favorite program list for the selected channel in the available channel list when the Programme Edit is selected Signal Information For DTV only Press A Y button to this position then press or OK button to enter Signal Information screen Auto Tuning It will auto scan the channels automatically and stop at the end of the channel search The auto scan result stores in the internal memory automatically DTV Manual Tuning Press lt button to select channel then press OK button to search programs LGD rW ATV Manual Tuning Color System Sound System BG Fine Tune 44 00 MHz AFC Off Search Programme Edit Delete Rename Move Skip oK Fav Menu Signal Information Channel 154 Frequency 205 50 Mhz Quality 99 Strength 22 ATV Manual Tuning Current CH Press lt gt button to select the channel number you want to store Color System Press lt gt button to change the color system as Auto SECAM PAL Sound System Press lt gt button to change the sound system as DK I BG Fine Tune Press lt gt button to scan current program within a frequency range accurately and store the result manually AFC Press lt gt button to set the Automatic Frequency Control to On or Off Search Press
27. r player you will see the region code notice on the screen The disc will not playback and should be unloaded The region code for this player is all refer to the symbols below 18 LED rW DVD Functions operating instructions 1 Play for DVD Super VCD VCD CD CD G HD CD and Mp3 JPEG discs USB CARD For DVD disc presspil button from root or title menu while playing the DVD you may play your favorite title directly with title selection by pressing the TITLE button For Super VCD amp VCD discs while playing the disc you may play your favorite tracks by numeric buttons For CD CD G amp HD CD discs while playing the disc you may play your favorite tracks by numeric buttons For MP3 JPEG disc you may play your favorite tracks by numeric buttons from the content menu If input track number is not valid it will not function NOTE From track 1 10 use numeric buttons directly For tracks over 10 press 10 button first E g Track 15 press 10 then 5 2 Previous Next for DVD Super VCD VCD CD CD G HD CD and Mp3 JPEG discs USB CARD While playing the disc Press KM4 button to play to the last Title Chapter track Press PI button to play to the next Title Chapter track For super VCD amp VCD discs in PBC OFF status If the current track is the first one press K4 button will stop the playback If the current track is the last one press gt button will stop the playback For DVD discs the a
28. rent Full Mute status Repeat mode status Current track time Press INFO button again to turn off the on screen display 7 Goto for DVD Super VCD VCD CD CD G HD CD and Mp3 JPEG discs USB CARD This function allows you to play your favorite Title Chapter track Press GOTO button to activate the on screen scroll down menu for edit According to the highlighted area input your favorite Title chapter Track number by numeric buttons or input the playback time After editing press OK to start If the input is in valid it will not function NOTE While editing the GOTO button does not function Ifitis in PBC ON status this function will switch it to OFF 8 Audio For VCD CD CD G HD CD and Mp3 JPEG discs USB CARD Press Audio button once to display current audio mode Press again to toggle between different audio modes in sequence For CD VCD MP3 HD CD discs stereo monoL monoR MIXMONO Note Switching to Auto L R audio channel may be varied due to different discs contents Bilingual VCD discs can use Audio button to switch between different languages 20 LED rW 9 Mute for DVD Super VCD VCD CD CD G HD CD and Mp3 JPEG discs USB CARD Press MUTE button to mute the audio output there will be an on screen symbol indicate MUTE Press again to cancel or Press VOL to cancel and adjust the volume In case there is no audio output try to press MUTE button to cancel mute 10 Repeat A B for DVD Super V
29. s EJECT button to take the disc out When the disc is ejected hold the disc edge slightly and take it from the eject direction to prevent scratches When not using the DVD function in stand by mode or using others modes for a long time please take out the disc to protect the DVD loader and the disc 5 Title playback for DVD disc only Press TITLE button there will be an on screen indication TITLE Press the direction or numeric buttons to select your favorite title Then will play from the first chapter of the selected title 17 LED rW Supporting DVD format This products can play the following format of DVD disc Disc Type Disc Size Diameter Recorded Time Recorded Content Single side 120mins Approx DVD format 12cm Compressed digital Double side 240mins Approx audio and video MPEG2 Super VCD 12cm 45mins Approx Compressed digital Include SVCD audio and video DVD MPEG1 Include VCD 12cm 74mins Approx Compressed digital VCD2 0 VCD11 audio and video VCD1 0 DVCD HD CD 74mins Approx HD DA Digital audio o9 MP3 JPEG 600mins Approx Digital audio pe NOTE Also support DVD R CD R CD RW playback A WARNING DO NOT INSERT OR PLAY 8CM DISC THEY WILL GET STUCK Region Code All As it is usual for DVD movies to be released at different times in different regions of the world all players have region codes and discs can have an optional region code If you load a disc of a different region code into you
30. slots or holes in the product The screen surface is easily scratched Do not touch the screen with your hands or any hard object Do not pull the power cord when disconnecting power Turn off at the switch on the socket and pull the plug not the cord Do not attempt to open this product yourself There are no user serviceable parts inside IL CID rW SAFETY WARNINGS Before using this product read and follow all warnings and instructions This product is not intended for use by young children Young children should be properly supervised This product is intended for household use only and not for commercial or industrial use Allow suitable distances around the product for sufficient ventilation Ventilation should not be impeded by covering ventilation openings with items such as newspapers table cloths or curtains Make sure the LCD TV stand is adjusted to a stable position Damage caused by using this product in an unstable position or by failure to follow any other warning or precaution contained within this user manual will void warranty 2 Accessories Check the accessories Remote control batteries LGD rW 3 Remote control Power Standby button Remote control indicator S MODE I II SLEEP Picture mode button Sound mode button USB SD Card function select Favorite program button Signal source select button Information display button Mute button Volume
31. ter the DVD OSD menu OSD Language O gi TD Use navigation buttons to select the OSD LANGAUGE setup LANGUAGE SETUP icon press OK button to confirm There are 5 languages OSD LANGUAGE for your selection pressA w buttons to toggle between AUDIO LANG GERMAN different languages ENGLISH GERMAN SPANISH FRENCH SUBTITLE LANG SPANISH ITALIAN MENU LANG FRENCH ITALIAN NOTE If the selected language is not included in you DVD disc content it will select the default language of the disc automatically The default language setting is English Audio Language Use navigation buttons to select the AUDIO LANG setup icon press OK button to confirm There are 5 languages for you selection press4 buttons to toggle between different languages ENGLISH GERMAN SPANISH FRENCH ITALIAN Press OK button to confirm NOTE If the selected language is not included in you DVD disc content it will select the default language of the disc automatically The default language setting is English Subtitle Language Use navigation buttons to select the SUBTITLE LANG setup icon press OK button to confirm There are 5 languages for you selection press 4 w buttons to toggle between different languages ENGLISH GERMAN SPANISH FRENCH ITALIAN OFF Press OK button to confirm NOTE If the selected language is not included in you DVD disc content it will select the default language of the disc automatically The default language setting is English
32. y only audio output When playing or pausing with picture playback you may use navigation butons to flip rotate the picture A button to flip horizontally W button to flip vertically button to rotate left 90 gt button to rotate right 90 When playing or pausing with picture playback you may use D MENU button to enter preview mode to display 12 pictures Press M4 gt gt button to select next previous page or press numeric buttons to view the corresponding pictures The maximum JPEG image size that can be displayed is 1280 x 1024 21 Function Settings DVD Function General setup Co a O Press DVD SETUP button to activate the DVD player OSD SYSTEM SETUP menu ey Press 4 gt button to move and highlight between different SCREEN SAVER o sub menu Press A w OK button to enter the highlighted PASSWORD sub menu EVNIINC POWER RESUME Press DVD SETUP button to exit the OSD menu DEFAULT NOTE In Setup mode the disc playback functions will be cancel or pause System Setup D LJ gs If SYSTEM SETUP EM _ i SAVER T SCREEN TV TYPE PASSWORD RATING POWER RESUME DEFAULT TV color system This menu enables you to set the picture format for your TV DVD NTSC This format is used by some other countries e g USA PAL This is the format used in Australia AUTO This format can be used if your TV DVD is capable of both PAL and NTSC for
Download Pdf Manuals
Related Search