User Manual
Contents
1. Information Am PDU Host Name DIGIBOARD System IP Address 192 Control Outlet Subnet Mask Configuration Gateway 2 168 0 254 PDU Enable DHCP Threshold DNS Server IP sser Primary DNS P 192 Netvvork Secondary DNS IP ServerLink PDU User Manual Ver 2 0 Configuration Mail When an event occurs the PDU can send an email message to a specified email address Email Server This setting must be a local or public fully qualified domain name Eg mailserver domain local or mail domain com au It cannot be an IP address Sender s Email Input the sender s email address Email Address Input the recipient s email address The message in the email will be as follows XXXXXXXX The above indicates the outlet status of ports A to H in order X 0 means the power off X 1 means the power on Note Make sure DNS server can resolve the Email Server s domain name SERVERL NK FoI Total load 0 0 A Status Normal Information Email Setting PDU Email Server mail your com System Control Sender s Email sender yourcom com Outlet Recipient s Email Address Configuration Email Address PDU Sp Threshold User Network Mail SNMP SSL ServerLink PDU User Manual Ver 2 0 12 Configuration SNMP When an event occurs the PDU can send out a trap message to a specified IP address Trap Notification Set receiver IP address for trap Community Set SNMP community2. ServerLink PDU User Manual Ver 2 0 Information PDU Displays total PDU outlet power consumption and Warning and Overload thresholds Garen Total load 0 0 A Status Normal Information PDU PoU PDU 0 0 A Normal System Control Threshold Outlet Warning 12 0 A Configuration Overload 16 0A PDU Threshold ServerLink PDU User Manual Ver 2 0 Information System Displays PDU system information including Model No Firmware Version MAC Address System Name System Contact Location Senvent ink Pro Total load 0 0 A Status Normal Information Model No SLP SB1008 H PDU Firmware Version s4 82 091012 1cb08s System MAC Address 00 16 18 77 0A 84 Control System Name PDU Outlet Configuration IE PDU Location Office Threshold ServerLink PDU User Manual Ver 2 0 Control Outlet Displays PDU outlet on off status Select the outlet by checking the box and then click ON OFF or OFF ON button to control the output power for PDU ON Press this button to turn on the assigned outlets OFF Press this button to turn off the assigned outlets OFF ON Press this button to reboot the assigned outlets Gemeen PCI Total load 0 0 A Status Normal Information PDU Status EH PDU OutletA ON O System OutletB ON Control OutletC ON O Outlet OutletD ON O Configuration OutletE ON O PDU OutletF ON O Threshold OutletG ON O User OutletH ON L1 Netvvork OFF Mail SNMP
3. Read Community is public and fixed Default Write Community is public and can be modified by user SERVERL NK Total load 0 0 A Status Normal Information Trap Notification PDU Receiver IP 192 168 0 1 System Control Outlet Community Configuration Read public PDU Write public Threshold d Netvvork Mail SNMP SSL ServerLink PDU User Manual Ver 2 0 13 Configuration SSL Enable SSL for web communication User must input the correct ID and password to enable SSL function Default ID is snmp Default password is 1234 SERVERLINK Total load 0 0 A Status Normal Information PDU Enable SSL F Confirmation System Control Outlet Password Configuration PDU Threshold User Network ServerLink PDU User Manual Ver 2 0 14
4. the Rack PDU Install In the Rack Remote Monitor The multiple PDU power PDU Install In the Rack PDU Install In the Rack Local Monitor Install In the Rack ServerLink PDU User Manual Ver 2 0 Hardware 1 Install mounting brackets 2 The ServerLink PDU comes with brackets for mounting in a rack To mount the PDU into a rack perform the following procedure 3 Attach the mounting brackets to the unit using the four retaining screws provided for each of the brackets 4 Choose a location for the brackets 5 Align the mounting holes of brackets with the notched hole on the vertical rail and attach with the retaining screws 6 Connect input and output power 7 Connect Ethernet cable to the PDU 8 Switch on the PDU Note 1 The default setting to assign the IP address is DHCP If the PDU cannot get the IP from a DHCP server the IP address will default to 192 168 0 216 ServerLink PDU User Manual Ver 2 0 5 Web Interface Login Enter the ServerLink PDU IP address into a web browser Default User Name is snmp Default Password is 1234 Connect to 192 168 0 59 28 gt The server 192 168 0 59 at Protected requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name c Password F Remember my password _o_ Gem
5. P Outlet A H Green Light on indicates outlet power is on Light off indicates outlet power is off Overload power protection 4 Installation Rack Mount Instructions A Elevated Operating Ambient If installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than room ambient Therefore consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature specified by the manufacturer B Reduced Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised C Mechanical Loading Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading D Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on over current protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern E Reliable Earthing Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit e g use of power strips Diagram lt PDU Install In the Rack S PDU Install In
6. SERVERLINK Senvent ink User Manual Table of Contents t ue goe leg Le EE 1 2 Package Contents ira oi e Fi 2 0 Ter el WEE E el EC HE ele ET 2 5 Web Dag ut e a e ia 4 1 Introduction The ServerLink PDU is a network ready device designed and equipped with an Intelligent True RMS Current Meter to indicate the total power consumption of connected devices The ServerLink PDU offers an easy to set up and user friendly interface The software enables you to remotely monitor power consumption of a single PDU or multiple PDUs Features Built in web server allowing real time monitoring of current consumption Built in True RMS current meter Easy Setup The meter can display the IP address of the PDU Homepage supports SSL Provides audible alarm when the power consumption exceeds the warning threshold or overload threshold Send email and traps when the power consumption exceeds the warning threshold or overload threshold Utility software can monitor a large amount of ServerLink PDUs at the same time Supports SNMP and provides MIB for the PDU to be monitored by NMS LED to indicate status of each outlet Supports power on sequence Supports user defined delayed time for power on and power off Provides power protection via the circuit breaker ServerLink PDU User Manual Ver 2 0 2 Package Contents The standard ServerLink PDU package contains a Power Distribution Unit with supporting hardware and softw
7. SSL ServerLink PDU User Manual Ver 2 0 Configuration PDU Set the outlet name and delay time Name Rename the outlet ON Set the delay time for power on sequence OFF Set the delay time for power off sequence Note The maximum delay time is 255 seconds SERVE NK FD Total load 0 0 A Status Normal Information PDU Name System Control OutletA OutletB Outlet ON Delay sec OFF Delay sec Configuration OutletC PDU Threshold OutletE Dean Outlet ServerLink PDU User Manual Ver 2 0 mn A Configuration Threshold Set the Warning and Overload threshold SERVERLINK Pro Total load 0 0 A Status Normal Information Threshold Amp Name PDU Warning Overload System PDU 12 16 Control eg Outlet A Configuration PDU Threshold ServerLink PDU User Manual Ver 2 0 Configuration User Change ID Username and password ID and password are case sensitive Default ID is snmp Default password is 1234 Gemeen 1 Total load 0 0 A Status Normal Information Original PDU ID System Control Password Outlet New Configuration ID PDU Threshold ServerLink PDU User Manual Ver 2 0 10 Configuration Network PDU network information Enable DHCP Change the way to assign the IP address for the PDU SERVER NK geren Total load 0 0 A Status Normal
8. are Power Distribution Unit Rack Mount Brackets e CD ROM containing ServerLink PDU User Manual ServerLink PDU Utility User Manual ServerLink PDU Utility Software MIB Management Information Base for Network ServerLink mib Adobe Acrobat Reader ServerLink PDU User Manual Ver 2 0 once METER SERVERLINK Functions Description Ethernet The Network connection for the built in web server Audible Alarm PDU exceeds warning threshold 1 beep per second PDU exceeds overload threshold 3 beeps per second Note The audible alarm will not change beeping status until the current drops more than 0 5A below the warning or overload threshold Function Button Press and release to turn off the warning beep The overload beeping cannot be cancelled Press and hold after 2 beeps release the button The meter will display the IP address of the PDU Press and hold after 4 beeps release the button and the PDU will change the way to assign the IP address via DHCP or Fixed IP Press and hold after 6 beeps release the button The PDU will reset the power to all outlets and restore all settings to factory default Meter Displays the current consumption or IP Address ServerLink PDU User Manual Ver 2 0 LED Indicator Circuit Breaker ServerLink PDU User Manual Ver 2 0 SSL Yellow Light on means web access is protected by SSL DHCP Green Light on means PDU is assigned an IP address via DHC
Download Pdf Manuals
Related Search