Home
USER MANUAL
Contents
1. 5 SD MS MMC Card Port Insert SD MS MMC card into this slot 6 USB Port Connect the USB device 7 INPUT button Tap this button to select enter the source selecting menu press the A V direction buttons to select desired mode and press the ENTER button to enter the selected mode In setup menu use the ENTER button for the same function A View of Unit 8 MENU button Tap this button to enter the system setup menu 9 CH VA buttons In ATV or DTV mode tap this button to select channels On system setup menu the same function as A direction buttons 10 VOL lt gt buttons Tap this button to decrease or increase the volume On system setup menu the same function as lt P direction buttons 11 POWER button Tap this button to enter or exit standby mode Front Panel TEAC a2 12 Color TFT screen 13 Speaker 14 Remote Sensor 15 Power Indicator Lights blue while system is active and red while system is in standby mode Flash red and blue light consecutively while DVR playback Recording View of Unit Rear Panel gr 2zl9 2956 USB port Connect the USB device for DVR record playback and software upgrade HDMI Input Jack Connect the HDMI signal source COAXIAL Output Jack Output the coaxial digital audio signal Y Pb Pr Component and L R audio Input Jacks Connect the Y Pb Pr Component signal source in Component mode COMPOSITE S VIDEO Input Jacks Connect Composite
2. then please disconnect the power and consult a qualified technician 52 Specifications LCDV1957DVR 19 inch TFT LCD TV 1440x900 Pixels 300 cd m2 800 1 Model Screen Size Native Resolution Brightness Contrast Radio 5 ms PAL BG I DK VHF UHF 48 25 863 25 MHz 75Q VHF UHF input NICAM A2 Response time ms Color System Sound System Tuner Antenna Stereo DVR Max Supported USB Volume 1TB Supported USB File System FAT32 Recorded File System Transport Stream TS 8 GB Max Time Shift Recording Size VIDEO INPUT CVBS input PAL SECAM NTSC Y C separate video signal Y 1 Vp p negative sync 75Oinput C 0 283 Vp p 75Oinput NTSC 0 3 Vp p 75Oinput PAL S VIDEO input RCA 0 7Vp p 750 input 4801 60Hz 480P 60Hz 5761 50Hz 576P 50Hz 720P 50Hz 720P 60Hz 10801 50 10801 60HZz COMPONENT HDMI 1080i 720p 1080p Audio in RCA audio input OTHERS DVD Player DVD RW DVD R CD CD R CD RW JPEG DivX 3 11 4 x 5 x 6 x Multi Media USB Card Reader MS SD MMC 3 in 1 Card reader and USB compatible Max Volume up to 2GB 15 Pin Analog RGB signal 0 7Vp p 75Oinput VGA SVGA XGA WXGA WSXGA computer signal compatibility VGA 1440 900 60Hz 1024 768 60HZz 800 600 60HZz 640 480 60Hz Teletext 1000 pages Audio out headphone audio output Specifications Note Specifications subject to change without pre notice Weight and dimensions are approximate 54 TEAC TEAC CUSTOME
3. CONNECTING to the POWEN SuDDly osain d neat bande a MR DAT RED XR TERR EU ba mab ied vd V exe HN b D DER 13 Connecting to th POWerAddptel aoi Het teen ied tot hi orla eheu P pao vete onto ut end 13 Connecting to ari External AV Signal SOUIGG 5 ade ioo RU Vel e P RO CRURA rd ra e o a et E A p EP OU E Rd 14 Connecting an External AV Signal Source YPDPY csssssssecsssssscsssecsssssscsssessssesscssseesssessessssssssecsesecsssecsesssecscsesecsesecessessesesecess 14 Connecting to an External AV Signal Source HDMI eee ette ee eese eerte tete rta testata tosta tta tentato setate setate sisse sensa sepes 15 Connecting to an External AV Signal Source AV Output eee eese eeete tenente tentes tato testate sta tos iato se tates inso sepes tosis 15 Connecting to Coaxial Digital OUTPUT n SOR epe UR e Dti dut eS DIRETTA FUR DNO T I NOE UE ERE 16 Connecting a Usb Devica uetus tritis etie cit aat aos estate A RAI emu cse Meroe tee telat 16 CONNEC INO Rio br gi At REM DL 17 Connecting toa TV DRE m m 18 Connecting to Ea MONS oerte ie fru RA Sen Nt e Por aD ss utet ive cae Noten d Gator Ade PERI ots 18 Input S urce Selecting c 19 TV Operation and HCHuETUI o MP 20 IAS Cell ACT on GUIE ssns E A A n M 20 CHANN LS IN a E EE M EL EM CAE 21 PECOS SEN G a A D ID Tern eaerer errs ar es rne eerie try erecta ears 23 SOUS 10 da 12 oceani ere nT Eee TAE rene Rene tare ee eT eer Re
4. EE button select desired disk The available item Cancel varies depending on the external USB device connected to the unit lt Press the WV button to highlight OK and press the ENTER button to confirm Check DVR File System Press the A V button to select Check DVR File System and press the or ENTER button to start to check the DVR File system After checking DVR file system the item USB Disk will display Pass indicating the file system in the USB disk connected has been checked and ready to use If the USB disk does not have a DVR File System then unit will prompt a message asking user to format it Format Press the A V button to select Format and press the gt or ENTER button to prompt a sub menu which E Er Select Disk occurs only when the USB device is plug in for the mm gt 5 File System Size first time as shown Fo DVRFileSystemSize All The item DVR File System Size is highlighted SEX FF and press the lt P button to choose the capacity Bu OT OK Cancel to be format The available capacity varies depending on the external USB device connected to the unit lt Press the WV button to highlight OK and press the ENTER button to format the disk you selected 30 TV Operation and System Setup lt During disk formatting please do not unplug the USB device and wait for several minutes NOTE lt We cannot guarantee compatibility operation and or bus power with all USB mass storage devi
5. Use the A V buttons to select desired item and press the ENTER button to play Stop During playback press the m STOP button to stop playback and return to root menu and press the gt PLAY button to play the file from the beginning Pause During playback press the PAUSE button once to pause the playback and press it again or press the gt PLAY button to resume normal playback Previous and Next Press the M4 button to go the previous file press the gt gt button to play the next file Fast Playback During playback press the 4 button to activate fast backward or forward playback During fast playback press the 9 PLAY button to resume normal playback REPEAT During playback press the REPEAT button repeatedly to select repeat mode GOTO Press the GOTO button repeatedly to select Select or Go To Use the 0 9 buttons to enter the desired time or and then the player will play according to the selected time Use the 0 9 number buttons and the 10 button to enter the desired track number then the player will play the selected track 45 DVD Playback Operation USB and SD MS MMC Card Function In DVD mode connect USB device to the USB port or ff insert SD MS MMC card into the SD MS MMC card slot on the left side of the unit ml TEAC lt Make sure that files are stored in the USB and SD MS MMC card before connection When you turn on the unit the media select menu will a
6. adjust the level Note The items Red Green and Blue are only available when Color Temperature is set to User Within the adjusting bar you can select Red Green and Blue by pressing the A Y button Aspect Ratio Press the A V button to select Aspect Ratio and press the lt P button to select 16 9 4 3 Auto Zoom1 or Zoom2 Noise Reduction Press the A V button to select Noise Reduction and press the lt P button to select Auto Off Low Standard or High Screen This item is only available in VGA mode Auto Adjust Press the A V button to select Screen and press the gt Horizontal Pos or ENTER button to enter its sub menu as shown on the Vertical Pos Phase right Within this menu press the A V button to select desired item and press the MENU button to return Press the EXIT button to exit Auto Adjust Press the A V button to select Auto Adjust and press the or ENTER button to start auto adjusting the screen Horizontal Pos Press the A V button to select Horizontal Pos and press the lt P button to adjust the level Vertical Pos Press the A V button to select Vertical Pos and press the lt gt button to adjust the level Size Press the A V button to select Size and press the lt b button to adjust the level Phase Press the A V button to select Phase and press the lt d gt button to adjust the level 25 TV Operation and System Setup Sound Setting Press the MENU button once to ente
7. button to select Color and press the lt gt or ENTER button to enter the color adjusting bar Press the lt gt o E P NB button to adjust the level Sharpness Press the A V button to select Sharpness and press the lt gt or ENTER button to enter the sharpness adjusting bar Press the lt gt button to adjust the level Tint Press the A V button to select Tint and press the lt gt or ENTER button to enter the adjusting bar Press the 4 button to adjust the level Notes This item is only available under NTSC signal mode The items Contrast Brightness Color Sharpness and Tint are only available when Picture Mode is set to User lt Within the adjusting bar you can select Contrast Brightness Color Sharpness and Tint by pressing the A V button Color Temperature Press the A V button to select Color Temperature and press the lt P button to select User Cool Medium or Warm Red Press the A V button to select Red and press the lt gt or ENTER button to enter the adjusting bar Press the lt gt button to select adjust the level Green Press the A V button to select Green and press the lt gt or ENTER button to enter the adjusting bar Press the lt gt button to select adjust the level Green me RP 24 TV Operation and System Setup Blue Press the A V button to select Blue and press the lt gt or ENTER button to enter the adjusting bar Press the lt gt button to select
8. buttons to select VGA mode and then press the ENTER button to confirm 17 System Connections Connecting to a TV Antenna Connect TV signal input source from the aerial to the TV jack on the rear panel of the unit i E un CY P I re z TJ ms d After connection turn on the power of the unit Then press the INPUT button and the direction buttons to select ATV or DTV mode press the ENTER button to confirm and conduct program selection Connecting to Earphones Connect earphones headphones to the earphone jack on the rear panel of the unit for listening to the audio output in seclusion The internal speakers output will turn off automatically after the earphones have been connected Excessively loud volume could damage your hearing Turn down the volume before you connect the headphones and then raise the volume to a comfortable level 18 Input Source Selecting The unit incorporates multiple input sources which can be selected via the Input button on the television or remote Press the INPUT button to enter Input menu The screen will display as shown below Component DVD VGA HDMI Composite S Video lt Usethe A V direction buttons and ENTER button On the input menu press the A V direction button to select the desired input source After several seconds you can enter the selected source Or after you selected the desired source press the ENTER button to enter the selected source imm
9. depending on the brightness in the room Notes Do not point bright lights directly at the remote control sensor lt Do not place objects between the remote control unit and the remote control sensor lt Do not use this remote control unit while simultaneously operating the remote control unit of any other equipment System Connections lt Do not connect the power cord until all other connections have been made Ensure that you observe the color code when connecting audio and video cables Connecting to the Power Supply Connect the power supply cord to the wall AC outlet see the figure below if To wall AC outlet lt a p Connecting to the Power Adapter Power is also supplied through the appropriate power adapter optional one end is connected to the DC 12V IN jack on the rear panel of the unit the other end to the AC100 240V wall outlet To wall AC outlet lt It could damage the V set that if the power supply cord and the power adapter are used simultaneously 13 System Connections Connecting to an External AV Signal Source Use the AV cables to connect the external AV signal source to the AV input jacks on the rear panel of the unit Use a S VIDEO cable not supplied to connect the external AV signal source to the S VIDEO input jack on the rear panel of the unit 32Jnog jeubis Ay eu131X3 After connection turn on the power of the unit and the external AV
10. eee ne ere Me EA te ree 26 Time SLA eR P 27 sae ame ai go Prem a eer pre are eo nro wor gen Pare mo Carer a Oe ee rr oan eee 28 DVRFUnCUOL iio o e ond e ti A n Uie tc eei a etaed M DE Dd 33 Time Shift Falc tous acd ditadelrafa rne Nar er titre esca ibi ute ante renee tU cur trap Ie te eee eens 33 aizieogellqreWel olo CANN ETE t 34 Playing recorded Progra ssa eio tee EUR Pt t i ORE ERR ED RERO RR HUBER REA RR UN unter aera 35 Schedule Recording MR TDI E 36 EPG PUI ei mr Tr M HP 38 NICAM FUT COLON me a a Aei 40 DVD Playback Operations ooa eb RERI Ie SERE ERROR ARS M REN TREETR ES NR NR AEYRR RA FRXVA AER TENE CAR RR SN NOXEEN DICE SEVERE ENR CELER IARE EXVE THER RU Fea Eh 41 Preparati ONAN cesses e oni ove deat ete E suni DumsEob sese ode ped N a e a IE UU tes Bros ov n IP RR IN UNDE MEA 41 BID dolore eR c A 41 CDPD dE TUR 43 JPEG Play Dar eases urine ert a Men Gear ao SCENT PT TO ere PvE Carre SIC Ol eT ee errr tact tec tesi 44 DIU CPIavDac Kaum etd MEM LM MM M E MM E EM M Neer eee 45 USB rahi SD MS MMC ard FUNE OI ced eet ah uestre ore biete ta Du e ase eL D dete 46 DVD Setup MOM Cr X 47 B egredi mee M M M 52 SDOCITIGATIONNS EET I T eR 53 Important Safety Instructions This sy
11. reference only and may differ from your model Important Safety Instructions NOTES IMPORTANT FOR LASER PRODUCTS Read these instructions 1 CLASS 1 LASER PRODUCT 2 DANGER Visible laser radiation when open and interlock failed or defeated Avoid direct exposure to Keep these instructions Heed all warnings Follow all instructions 7 beam o not use near water l CAUTION Do not open the back cover There are no Clean only with dry cloth Me m user serviceable parts inside the unit Leave all servicing Oy I AI S Do not block any ventilation to qualified service personnel openings Maintain well ventilated conditions around the product Do not put product on a bed sofa or anything that blocks ventilation Install according to the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Read heed and follow all instructions to ensure correct and safe installation and interconnection of the apparatus 10 The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus 11 The mains socket outlet shall be installed near the apparatus and the mains plug shall remain readily operable 12 Protect the power cord from being walked on or pinched particularly at plugs power sockets and the point where they exit fro
12. select desired item and System press the lt P button to set or activate Press the red button to Current CH save the settings search Fine Tune Skip Program Edit Press the A V button to select Program Edit and press the 4 mE ENTER or button the screen will display as shown Program Edit lt Seta favorite channel Within the menu press the A V button to select a channel and press the FAV LIST button to set it as your favorite channel press the FAV LIST button again to cancel lt Delete a channel Press the A V button to select a channel you want to delete and press the red button to set a symbol E on the channel Press the red button again to delete the selected channel press the MENU button to return 22 TV Operation and System Setup Rename a channel this function is only available for ATV channels Press the A V button to select a channel you want to rename and press the green button to set a symbol am on the channel Press the lt b button to highlight the character position of channel name and press the A V button to select desired character press the green button to confirm and return lt Move a channel this function is only available for ATV channels Press the A V button to select a channel you want to move and press the yellow button to set a symbol A on the channel Press the A V button to select the desired position and press the yellow button to move the selected channel to the pos
13. services In addition the detailed information about the program is often available in the EPG the availability and amount of these program details will vary depending on the particular broadcaster This function can be used only when the EPG information is broadcasted by broadcasting companies Switch on off EPG lt Press the GUIDE button to switch on EPG lt gt Press the GUIDE or EXIT button again to exit EPG and return to TV viewing Button Function in Program Guide Mode PROGRAM GUIDE 02 May 2009 14 50 DTV 14 30 800 TF1 New Youk Police Juciaire Mes deux BD1 MRJ1 ES NOUVELLES PUS LES NOUVELLES PUSSTCAT LES NOLIVELLES PUS New Youk Police Juciaine OW PLAGE DE LECTURE BALKO Balko suspect un BALKO Le tresor Remote Control Buttons VG Press to display the detailed information about the highlighted les program Press to display the program reminder schedule list menu 38 EPG Function To schedule a program reminder Select a program on the PROGRAM GUIDE menu then press the blue button to enter the Reminder menu as shown on the right Program If you want to adjust any of the settings press the A V E button to select desired item and press the lt P button to Mode rre set it Date 06 lt Press the ENTER button to save your settings Month lt Press the EXIT button to exit Within the Reminder menu above press the green button to display the program reminder schedul
14. the USB data transfer rate Max record time Press the A V button to select Max record time and press the lt P button select desired time as the max record time Note While doing instant recording record will be stopped once it reaches the max record time Allow Update Press the A V button to select Allow Update and press the lt P button to select On or Off 31 TV Operation and System Setup System Update Time Set the time when the system update automatically OSD Time Out in standby mode NE DVR File System Press the A V button to select System Update Time iata I System Update Time and press the or ENTER button to prompt an information box as shown Within the sub menu press the A V button to select Hour or Minute press the lt gt button to set Press the ENTER button to close after selecting Close NOTES lt Update functions only in standby mode lt If you want to update the system please power off the TV set after setting the time Unit will only update if Over The Air Update is available for this unit 32 DVR Function In DTV Mode Only DVR function allows the unit to record live DTV program and make it available for reviewing at any time NOTE lt When DVR function is in progress please don t unplug the power and the external USB device at will lt When DVR function is active the power indicator will blink with red and blue consecutively lt Before start recording a progr
15. the contents Many discs have other contents besides pictures For Picture CD disc it will display the pictures automatically During playback press the M4 gt gt button to select the picture Many discs have other contents besides pictures Stop Press the m STOP button to preview the pictures behind currently playing picture in the way of small pictures Press the PLAY button to resume normal playback Pause Press the PAUSE button to pause playback press the PAUSE button again or PLAY button to resume playback Repeat During playback press the REPEAT button repeatedly and the repeat modes are Shuffle Random Single Repeat One Repeat All and Repeat Off Menu Press the MENU button once to stop playback and return to the root menu GOTO During playback press the GOTO button on the remote control once use the number buttons to input the file number Picture Rotation During playback press the lt P button to rotate the currently displayed picture This function only activates for the current picture once another picture is displayed rotation will be cancelled automatically lt Some JPEG discs may not support the rotation function 44 DVD Playback Operation DIVX Playback DIVX is the name of a revolutionary new video code which is based on the new DIVX compression standard for video 1 Load a DIVX disc in the disc tray the player will enter the reading mode 2 Thescreen displays the root menu
16. to select desired country and press the V button to highlight Start a To cancel auto tuning press the ENTER button after 3 highlight Cancel by pressing the lt P button To start auto tuning press the ENTER button after highlighting Start The screen will display as shown Channel Tuning When auto tuning is over all searched channels will be stored 26 473 00 MHz TV automatically and it will return to the first searched channel L eee During searching press the MENU button to skip some range of AT LAE available channels Press the EXIT button to exit DTV 0 Program s Notes Radio 0 Program s Channel Tuning scans the analog channels digital channels Press MENU to skip Press lt EXIT gt to exit and Radio programs lt Please allow a few minutes for this feature to scan the entire range of available channels to insure accurate programming of available channels 21 TV Operation and System Setup DTV Manual Tuning Press the A V button to select DTV Manual Tuning and press the ENTER or gt button the screen will display as shown on the right Press the lt gt button to select desired channel number and press Deas coleck channel then the ENTER button to start tuning Press ENTER to search ATV Manual Tuning Press the A V button to select ATV Manual Tuning and press the ENTER or gt button the screen will display as shown on the right Within this menu press the A V button to
17. to shift the sound tracks between DUAL I DUAL Il and DUAL I II and the screen will show the corresponding display as shown below DUAL I 2 DUALII gt DUAL I II 3 When receiving mono audio signals press the STEREO button on the remote control to display sound track Mono on the screen 40 DVD Playback Operation Preparation 1 Connectthe unit to the power supply and press the POWER button to turn on the unit 2 Repeatedly press the INPUT button on the remote control to select DVD mode and press the ENTER button to enter 3 Gently insert the disc with the label side toward the front of the television into the disc tray slot until about half of the disc is in the tray and then the disc will be drawn into the disc tray and loaded automatically 4 Pressthe EJECT button to eject the disc but the disc can not be drawn into the disc tray by pressing the EJECT button again You must push the disc until it is drawn into the disc tray automatically Label 5ide ON Warning Use of poor quality discs could result in damage to the television DVD Playback Region Code DVD players and discs are coded by region These regional codes must match the played discs If the codes don t match the disc cannot be played This player s default code is 4 Play Press the PLAY button to start playback Stop During playback press the m STOP button once to stop playback and press the gt PLAY button to resume normal playba
18. LCDV1957DVR 19 HD Wide Screen LCD TV USER MANUAL IMPORTANT WARRANTY INFORMATION INSIDE PLEASE READ Trademark of TEAC Corporation JAPAN www teac com au TE AC WARRANTY INFORMATION v1 5 2 DEC 2011 Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Warranty Terms amp Conditions 1 TEAC warrants that this product is free from defects in material and workmanship under normal domestic use with reasonable care and skill Maintenance and cleaning i e laser head is not covered by this warranty The TEAC warranty only applies to TEAC products purchased used and serviced in Australia 2 The benefits to the consumer given by this Warranty are in addition to other rights and remedies of the consumer under a law in relation to goods or services to which the warranty relates being the Australian Consumer Law oe Refund or replacement via your retailer is available for a period of 14 days after purchase for goods that have been inspected and determined to have a major failure Refund and exchange is not applicable for change of mind 4 Subject to the terms herein this warranty effectively covers th
19. Notes CHECK ITEM Make sure the disc is loaded in Make sure the disc is not dirty or warped Make sure the player s region code is the same as the region code of the DVD disc Make sure water condensation has not occurred If it occurs take out the disc and leave the player on for at least one hour Make sure the system connection is correct Make sure the sound setup of the DVD disc is correct Make sure the disc is not dirty or warped Clean or replace the disc Make sure the speakers are not muted Set the correct sound mode Make sure the unit is turned on and the connections are correct Make sure the power adapter is correctly connected Make sure it is not in repeat status Make sure the disc is not dirty or damaged Check if the connections with the external AV signal source are correct Correctly set the items in the picture menu Check if the video type input signal is not corresponding to the unit Make sure the unit is turned on and in the correct video type Make sure there are no obstructions between the remote control and the player Make sure the remote control is pointing at the player Make sure the batteries are inserted and the polarity is correct Make sure the battery is not weak Static or other external interference may cause the player to behave abnormally If this occurs unplug the power supply cord from the outlet and plug it in again to reset the player If the problems persist
20. R SUPPORT HOTLINE TCS 1300 553 315 Between Monday to Friday AEST 8 30AM to 6PM
21. S Video signal source in Composite or S Video mode Composite and S Video share L R audio jacks VGA Input Jack Connect the VGA signal source in VGA mode 10 11 1a Composite AV Output Jacks Connect to output the audio video signals in Composite mode TV antenna Input Jack Connect the external TV antenna signal source Earphone Jack When connected to earphone the internal speakers will automatically turn off DC 12V IN Jack Connect the power adapter Power Supply Cord Special Feature of DVD Module Your TV comes equipped with a removable DVD module Please follow the procedures below to remove or install the DVD module Note Before removing or installing the DVD module ensure that the television is unplugged and turned off DVD module removal Refer to the illustration below and follow the procedures below to remove the DVD module from the unit 1 Loosen the screw on the DVD module 2 Carefully slide the DVD module along the rails and unplug the connecting cord from the LCDTV 3 Slide the DVD module along the rails to fully remove the DVD module DVD module installation 1 Plug the connecting cord into the DVD module 2 Carefully slide the module into the desired position and lock the function module with one screw Disc Information Discs Supported secos omes sm meme Audio Video active picture CO JESUS 74min DIGITAL AUDIO lt The operating method of some DVD
22. am please make sure the external USB device is connected lt While recording if the available storage space becomes low the recording will be automatically stopped Time Shift Function This function allows you to pause and fast forward rewind normal Live DTV viewing at any time without missing any of the live broadcast provide that a USB storage device is connected 1 While viewing a DTV program press the D button on the remote control to pause live TV A progress bar is displayed on the screen Current time behind live TV 2 Total allowable time for time shifting Varies depending on the time shift size lt The progress bar will fade out in 10 seconds Note Press EXIT button to toggle between Time Shift info banner and minimize icon at the bottom right of the screen Both info banner and minimize icon will fade out in 10 seconds 2 Press the button to continue playing the program from the point where it was paused An progress bar is displayed on the screen The progress bar will fade out in 10 seconds lt Time shift function stops when the current save time becomes 00 00 00 33 DVR Function 3 While in Time Shift mode below operations can be use o e Press the or button repeatedly to increases the fast forward rewind speed e e Press the o button to jump about 30 seconds forward Pressthe button to jump about 30 seconds backward Press the button to onc
23. cel da 1 box as shown on the right Press the lt P button to select a desired country Pressthe V button to highlight Start and press the ENTER button _ Channel Tuning to start auto searching the available channels The menu on the 2696 473 00 MHz TV ERE right will be displayed on the screen to show the progress of the ATV 7 Program s DTV 0 Program s search for ATV DTV and Radio programs lt During searching press the MENU button to skip some range of Radio 0 Program s available channels Press the EXIT button to exit Press MENU to skip Press lt EXIT gt to exit 20 TV Operation and System Setup If you use the unit for the first time or if your setup has changed you can setup the unit from Channel Setup menu Please follow the instructions below Channel Setting Press the MENU button once to enter CHANNEL setup menu as shown on the right Auto Tuning DTV Manual Tuning Press the ENTER or gt button to enter the menu ATV Manual Tuning In the CHANNEL setup menu press the A V button to Am Porgram Edil select the desired item i Press the MENU button to return to the previous menu Press the EXIT button to exit Auto Tuning Press the A V button to select Auto Tuning and press m the ENTER or gt button the screen will display as shown DTV Manual Tuning on the right Sese slack country reb Then select Start to update info Press the lt gt button
24. ces and assumes no responsibility for any loss of data that may occur when connected to this unit lt With large amounts of data it may take longer for the system to read the contents of a USB device Unit may require longer time to format depending on the volume of the USB device lt Some USB devices may not be properly recognized lt Even when they are in a supported format some files may not play or display depending on the content lt Please make sure the USB device s file system is FAT32 WARNING lt All data on the connected device will be lost if you confirm to format lt Itis strongly recommended that the USB device is dedicated only for this unit Various external data contain in the USB device might cause DVR file system corrupt and requires formatting lt Once USB device is formatted unit will create a unique file system on it Therefore it is not advisable to connect USB device to a computer to export data Time Shift Size lt After the disk format is finished the menu as h the right will dnd ius s i ou Time Shift Size lt The item Time Shift Size is highlighted press the _s Time 5hift Size 512 MB b button to choose a size to be allocate for SD 14 Min HD 4 Min time shift The maximum value is 8G si F OK Cancel lt Press the W button to highlight OK and press the ENTER button to confirm and return Speed Once USB device is checked this item will display
25. ck Press the m STOP button twice to stop playback completely Pause During playback press the PAUSE button once to pause the playback press it repeatedly to start step by step playback Press the PLAY button to resume normal playback 41 DVD Playback Operation Previous M and Next gt Press the M button to go to the next chapter Press the M4 button once to return to the beginning of the current chapter or track press it twice to go to the previous chapter Fast Playback During playback press the gt button to activate fast backward or forward playback During fast playback press the B PLAY button to resume normal playback Repeat Press the REPEAT button repeatedly to repeat a chapter title or all lt Some discs do not support the repeat function Menu Normally there is a selecting menu for DVD discs You can press the MENU button under DVD mode to enter the menu and use the direction buttons to highlight an item Then press the ENTER button to confirm Title amp Chapter Normally there are several titles in a DVD disc and several chapters sections in a title Press the TITLE button to enter the title menu and you can select any title or chapter quickly by entering the relevant number lt Some discs do not support the function by inputting the number button but the A V 4 direction buttons Language Audio There can be up to 8 audio languages on a DVD disc When you play a multi languag
26. corded list l J Recorded List Program 4 1 4 Press the DVR LIST button on the remote control to enter the EH Mes deux maps RR Recorded List as shown mo o ea lt Press the DVR LIST button repeatedly to list the files by named Mes deux maris Coronation Street Program Channel or Time Press the A V button to select desired file and press the DISPLAY or gt direction button to display the information of the file Press the A V button to select desired file and press the ENTER button to playback selected file While playing you can see a playback progress bar as shown below 800TFi Mes deux maris Mes deux lt The progress bar will fade out in 10 seconds lt Press EXIT button to toggle between Time Shift info banner and minimize icon at the bottom right of the screen Both info banner and minimize icon will fade out in 10 seconds During playback below operations can be use G5 Press the VB to pause playback Press the D button to return to a normal playback e e Press the or C button repeatedly to increases the fast forward rewind speed e Press the button to jump about 30 seconds forward Vet Pressthe button to jump about 30 seconds backward Press the button to once to set the beginning point A and press the e button again to set the ending point B Then the segment A B will be played repeatedly Press the D button to cancel the repeat segment If
27. d use the blue button to skip a channel see P23 for details In teletext mode they are the teletext colour buttons REPEAT button Press to repeat a chapter track title or all program content in DVD mode In teletext mode press to hold the current page and press again to resume TITLE button During disc normal playback press to go to display the title menu In teletext mode press the button first time to double the size of teletext letters in the upper half of the screen second to double the size of teletext letters in the lower half of the screen and third to resume normal status Remote Control Remote Control Drawing ATW POWER d DVD GUIDE DOSS Soo AA ANS A MAN A M ES E El E3 SIEREO PICTURE SLEEP DISPLAY ASPECT 388 SEE TEAC RC 6236 32 CARD button Press to display the media selecting menu in DVD mode 11 33 34 35 36 37 38 39 40 41 In teletext mode press to select four groups of 3 digit numbers that are displayed in different colors at the bottom of the screen Press the colour buttons on the remote control to select then use the number buttons to input the corresponding number to display the page Repeat the above procedures for each page to be stored using a different colour button each time GOTO button Press to select the desired disc starting time title or chapter in DVD mode In telet
28. discs is specified by the software maker Please refer to the instruction manual of the disc lt The unit will play most recordable CD R or erasable CD RW CDs but playback of CD R or CD RW discs created on a computer requires proper formatting and finalization of the disc for audio playback Some computers and or software programs may not be capable of creating compatible discs About Disc Terms Title Generally pictures or music compressed on a DVD are divided into several sections title Chapter The smaller section unit of pictures or music in a DVD under the title usually one title is comprised of one or more chapters and each of them is numbered for easy searching But some discs may not have a recording by chapter facility Track A segment of picture or music on a CD Each track is numbered for searching Remote Control Remote Control Drawing 8 come sem EENE e mme quem pur EE E ES El EJ N EB DTV SOUND TV RADIO GUIDE onus 44 ipaa P __ SETUP MENU TITLE REPEAT SUBTITLE AUDIO GOTO CARD CH LIST TIMER LIST INPUT FAV LIST STEREO PICTURE DISPLAY ASPECT POWER button Press to enter or exit standby mode SLEEP Eg Lad 7i E3 ARAA SEI A N A E F3 IE ES tikje fe uj B 10 DTV button Press to enter DTV mode SOUND button Press to select the screen picture mode choose from Standard User Sports Movie or Music TV RADIO b
29. e DVD disc you can use the AUDIO button on the remote control to select a desired language GOTO During DVD disc playback press the GOTO button on the remote control once there will be a menu displayed on the screen You can set or select items for your preference Use the A V direction buttons to select items and press the ENTER button to enter and use the A V direction buttons to select the desired item Press the lt direction button to return When selecting the Title Chapter TT Time CH Time use the number buttons to input the desired title chapter time lt Some DVD discs do not support the search function Subtitle The DVD player can support multiple kinds of subtitles When you play a multi subtitle disc you can press the SUBTITLE button on the remote control to select different subtitles lt Some discs do not support the shifting subtitle function 42 DVD Playback Operation CD Playback The player will play all tracks on a CD disc by default You can use the M4 gt gt buttons or number buttons to select a track Stop Press the m STOP button once to stop playback and press the gt PLAY button to resume normal playback Press the m STOP button twice to stop playback completely Pause Press the PAUSE button to pause the playback and then press the PAUSE button again or gt PLAY button to resume normal playback Previous and Next Press the M4 button to go the beginning of the current track Press twice repeat
30. e direction buttons A V on S the remote and press ENTER to confirm Select an option value to be set using the A V direction buttons on the remote and press ENTER to confirm or press lt to cancel setting After ENTER you return to the main menu using BETSAUJSSENEPESS 48 DVD Setup Menu Dolby Digital Setup Dual Mono This function is used to set audio output Stereo Stereo signal output L Mono Left audio channel signal output R Mono Right audio channel signal output Mix Mono Output of left and right mixed audio signals Dynamic Use this function for setting the linear dynamic compression ratio that can be used to implement various signal compression effects The greater the compression ratio the smaller the difference between highs and lows This option is only available for Dolby Digital audio As shown above switch into the sub menu and select the desired value with A V Use ENTER to confirm and lt to end setting HDCD Setup Filter As shown above switch into the sub menu and select the desired value with A V Options are Off 1x 2x Use ENTER to confirm and lt to end setting Video Setup Page Press the SETUP button in DVD mode Use lt gt to select the Video Setup menu The Video Setup menu will appear Select the submenu Quality using the direction buttons A V on the remote and press ENTER to confirm Select further options and an option value to be set using the A V direction butto
31. e equipment as specified in the Warranty Periods Table below from the date of purchase TEAC PRODUCT WARRANTY PERIOD LED LCD TV 32 80 cm and above 1 Year In Home Service Pick up Available All other TEAC products 1 Year Carry in Service 5 In Home Service Pick up Service This service will only be provided as part of this warranty if all the following conditions are met a he product is indicated in the Warranty Period Table b The product is within the warranty period c The product is located within the normal service area of the local TEAC Authorised Service Centre If TEAC determines that the product is not repairable on site TEAC can complete the repair by taking the product to a TEAC Authorised Service Centre Carry in Service Where In Home service Pick up is not available the purchaser is required to send the product to the nearest TEAC Authorised Service Centre for repair In this event proof of purchase is required to support a warranty claim After the repair the product will be available for collection by or return to the purchaser at a fee upon request TEAC in home service can be made available at a fee upon request 6 A 12 month replacement warranty is applicable to all Accessories such as Remote Power Adaptors and Cables f TEAC will ensure to the best of its abilities that all required parts are made available for any required service repair 8 TEAC Australia Pty Ltd and its Authorised Service Ce
32. e list as shown below 02 May 2009 14 50 Date Program To delete a program reminder Within the REMINDER SCHEDULE LIST menu press the A V button to select desired item and press the red button to delete it Press the EXIT button to exit 39 NICAM Function The unit supports NICAM function when in TV mode Under NICAM TV broadcast 1 Whenreceiving stereo audio signals press the STEREO button on the remote control repeatedly to select the sound tracks between NICAM STEREO and Mono and the screen will show the corresponding display as shown below 2 When receiving bilingual audio signals press the STEREO button on the remote control repeatedly to shift the sound tracks between NICAM DUAL I NICAM DUAL II NICAM DUAL I II and Mono and the screen will show the corresponding display as shown below NICAM DUAL NICAM DUAL II gt NICAM DUAL I II gt 3 When receiving mono audio signals press the STEREO button on the remote control repeatedly to shift the sound tracks between NICAM Mono and Mono and the screen will show the corresponding display as shown below Under A2 TV broadcast 1 When receiving stereo audio signals press the STEREO button on the remote control repeatedly to shift the sound tracks between Stereo and Mono and the screen will show the corresponding display as shown below gt 2 When receiving bilingual audio signals press the STEREO button on the remote control repeatedly
33. e to set the beginning point A and press the e button again to set the ending point B Then the segment A B will be played repeatedly Press the D button to cancel the repeat segment Recording program After you setup the settings on the DVR File System menu you can record a DTV program on the external USB device 1 Select the desired program then press the record CB button on the remote control to start recording and progress bar will be displayed lt During recording the progress bar will fade out in 10 seconds Pressthe button again an icon ws will blink on the bottom right corner of the screen and it will fade out in 10 seconds 2 Recording stops when you press the I STOP button and the recorded file is stored in the external USB device automatically 3 Press the PLAY button to start to play the file fresh recorded Recording in standby mode This unit is able to do recording while in sleep mode lt Start a recording then press the power button Still keep recording A message as shown on the right will be displayed lt Select Yes to record in standby mode Yes No Select no to switch unit to standby lt While recording in standby mode unit will not output any picture or sound The power indicator will flash in blue and red consecutively while there is a recording in standby mode 34 DVR Function Playing recorded program E You can play the selected program in the re
34. ediately lt Use the INPUT button and ENTER button On the input menu press the INPUT button repeatedly to select the desired input source After several seconds you can enter the selected source Or after you selected the desired source press the ENTER button to enter the selected source immediately 19 TV Operation and System Setup Preparations 1 After connection press the POWER button to turn on the unit 2 Pressthe INPUT button to select ATV or DTV mode and you can then conduct the following operations Note In other mode you can refer to the following instructions in DTV or ATV mode to go on with some settings Installation Guide When you turn on the unit for the first time or after you reset all the settings to their original status the Installation Guide page appears automatically Please follow the instructions to finish the installation guide setup It helps to quick set the language and get the channels lt The Installation Guide menu shown on the right will be Installation Guide displayed on the screen Language lt The Language option is highlighted and the default is Uto Tuning English You can select the desired OSD language you want by pressing the lt P button lt Press the W button to highlight Auto Tuning option and Installation Guide press the ENTER or gt button to prompt a information Sos English Auto Tunir Please select country first Then select Start to update info Start Can
35. edly to go the previous track Press the button to play from the beginning of the next track Fast Playback Press the button on the remote control to activate fast backward or forward playback Repeat Press the Repeat button repeatedly to repeat a single track all tracks or to exit repeat mode lt Some discs do not support the repeat function Audio During playback press the Audio button to toggle audio output between Mono Left Mono Right Mix Mono or Stereo GOTO Press the GOTO button to access the time selected state You can select Disc Go To Track Go To or Select Track respectively by pressing this button repeatedly Use the 0 9 buttons to enter the desired time and then the player will play according to the selected time Use the 0 9 number buttons and the 10 button to enter the desired track number then the player will play the selected track 43 DVD Playback Operation JPEG Playback JPEG is a common picture format that requires small amounts of storage per image and has low loss in resolution Hundreds of pictures can be stored on a disc in this format In order to view JPEG photo albums you can ask your film development company to make a PICTURE CD when they develop your film Normal Playback Load a JPEG disc in For JPEG disc there will be a root menu displayed on the screen Use the ENTER button and the direction button to select a submenu and then use the A V lt gt direction button to select
36. esired main menu 2 Select the desired submenu using the direction buttons A V on the remote and press ENTER to confirm Select an option value to be set using the A V direction buttons on the remote and press ENTER to confirm or press lt to cancel setting After ENTER you return to the main menu using 3 SETUP takes you back out of the setup menu General Setup Page Press the SETUP button in DVD mode The General Setup menu GeneralSetup Page wubapPedl eee ee Select the desired submenu using the direction buttons A V on OSD Lang ENG the remote and press ENTER to confirm Select an option value CSS zi to be set using the A V direction buttons on the remote and SEMINE MSN press ENTER to confirm or press lt to cancel setting After ENTER you return to the main menu using Go To General Setup Page TV Display GeneralSetup Page Used for setting the screen mode 4 3 PS 4 3 LB 16 9 and Wide IMDISpISY PS Squeeze are available RD ENS Select 4 3 PS Pan Scan or 4 3 LB Letter Box when a 4 3 TV is cond A connected AR EES T Select 16 9 and Wide Squeeze when using a 16 9 screen on the unit set TV Display Mode Angle Mark General Setup Page This is where you can change the camera angel of the scenes TV Display PS being played if the DVD this function is available Angle Mark On i OSD Lang ENG On A camera symbol appears on the screen If there are Captions Ott 2 Screen Save Dn alternative v
37. ext mode press to display the real clock and press the EXIT button to exit TIMER LIST Press to display the recorder schedule list FAV LIST button Press to display the favorite channel list In Program Edit menu press this button to set a favorite channel see P22 for details EXIT button Press to exit all the OSD on the screen CH button In ATV or DTV mode press to select analog channel or digital channel MUTE button Press to turn on or off the speaker output 10 button In DVD mode press to select numbers greater than 10 SLEEP button This feature allows you to set the sleep time Press the button repeatedly to select the desired time to sleep or select Off to close the function ASPECT button Press to shift the aspect ratio of the screen among 16 9 Zoom1 Zoom2 Auto and 4 3 Remote Control Preparation of Remote Control Softly push the back cover to open the battery c Insert two batteries 1 5V size AAA please make sure the polarity matches the marks inside the compartment compartment Softly press the back cover to close it Under normal use the battery will last for six months lt Take out battery when the remote is not in use for a long time 12 Using of Remote control Point the remote control unit from no more than about 7 meters from the remote control sensor and within about 60 degrees of the front of the unit TEAC lt The operating distance may vary
38. iew angles a corresponding message M NER appears Off No camera symbol is displayed Set Angle Mark 47 4 3 Ps a 3 Lb 16 8 Wide Squeeze On Off DVD Setup Menu OSD Lang General Setup Page rv Display 5 Please select preferred language for the OSD menus Aoki in OSD Lang ENG English Captions OT French Screen Saver On Spanish Last Memory Off German Italian Set OSD Language General Setup Page Captions TV Display PS a u 7 Angle Mark On You can activate the captions display during playback with On OS Lang ENS or deactivate the display with Off Captions Off On Screen Saver On Ofi Last Memory Off Closed Caption General Setup Page Screen Saver TV Display PS When activated under stop mode the unit will go into screen Oei E saver mode if the same image remains on the screen for several Captions Off Screen Saver On On minutes Last Memory Off Ort Screen Saver General Setup Page Last Memory TV Display PS Use this option to switch the Resume after playback Suede EA OSD Lang WG interruption function on or off Use A V to select On or Off Captions Off Screen Saver On use ENTER to confirm and lt to end setting LastMemory Off On Off Set Last Memory State Audio Setup Page Press the SETUP button in DVD mode Use lt gt to select the Audio Setup Page Audio Setup menu The Audio Setup menu will appear Dolby Digital Setup Select the desired submenu using th
39. ilable when AD Switch is set to On 26 TV Operation and System Setup Surround Sound Press the A V button to select Surround Sound and press the lt P button to select Off SRS TruSurround XT or Surround Surround Mode Press the A V button to select Surround Mode and press the or ENTER button to enter the sub menu as shown Within the sub menu press the A V button to select desired item and press the lt P button to set Press the MENU button to return to the previous menu Press the EXIT button to exit Note Surround Mode is only available when Surround Sound is set to SRS TruSurround XT Time Setting Press the MENU button once to enter CHANNEL setup menu and press the A V button to select TIME the screen will display as shown Press the ENTER or gt button to enter the menu In the TIME setup menu press the A V button to select the desired item Press the MENU button to return to the previous menu Press the EXIT button to exit Clock Press the A V button to select Clock and press the or ENTER button to prompt a information box as shown Press the A V button to select Date Month Year Hour or Minute press the lt P button to set Press the ENTER button to confirm after selecting Close NOTES lt In DTV mode the Clock function is not available when there is DTV signal input Dialog Clarity Clock Off Time On Time Sleep Timer Auto Sleep Time Zone Clock Off Time On Time Sleep Ti
40. ions Connecting to Coaxial Digital Output This unit is designed with a coaxial digital audio jack can be connected to the digital amplifier see the figure below TAL AMPLIFIER DIGI lt This feature is available only for amplifiers equipped with coaxial digital audio input connectors lt ForTVs with a built in DVD player optional and an amplifier with Dolby Digital decoding function set the digital audio signal output format in DVD setup menu to AC3 Connecting a USB Device This unit is designed with a USB port so that you can connect your USB device and use the build in DVR record function It is also used for software upgrade See figure below lt Make sure that Software file for upgrade is stored in the USB device before connection lt For more information about DVR please refer to DVR File System Page 30 16 System Connections Connecting to a PC Follow the steps and figure below to connect PC to the unit 1 Connect one end of the VGA cable to the VGA input jack on the jack panel of the unit and the other end to the PC VGA output 2 Connect one end of the audio cables to the PC audio input jack on the jack panel of the television and the other end to the PC audio output jack 3 Set the PC video resolution to match that of the television Native 1440 x 900 60HZ After connection turn on the power of the unit and the external AV signal source Press INPUT then direction
41. isc tray or all the operation has been stopped Press the SETUP button in DVD mode Use lt gt to select the ZCPIBROSPRGSTE Preference Setup menu The Preference Setup menu will aem ENG dd Baoan ENG Select the desired submenu using the direction buttons A V eurn on the remote and press ENTER to confirm Select an option value to be set using the A V direction buttons on the remote and press ENTER to confirm or press lt to cancel setting After Go To Preference Page ENTER you return to the main menu using 50 DVD Setup Menu Audio Subtitle and Disc Menu If a DVD contains several languages you can choose the Audio ENG Preference Page subtitle Off language for the playback subtitles and DVD menu Diss Men ELS Default Preferred Audio Language Default Preference Page This option is used to reset the unit The factory settings are Audio ENG Subtitle OH adopted Disc Menu ENG Notes Default lt Resetting is only possible when the disk is removed from the DVD drive lt All your settings done so far will be deleted Load Factory Setting 51 English French Spanish German Italian Japanese Hussian Chinese Reset Troubleshooting SYMPTOM The player cannot play There is no sound LCD has no display Cannot continue to play and play a section repeatedly There is no picture or picture jitters up and down Unsteady The remote control does not work Other
42. ition you select Skip a channel Press the A V button to select a channel you want to skip and press the blue button to set the channel skipped A symbol SKIP is appear on the skipped channel Press the blue button again to cancel press the MENU button to return Note A skipped channel is skipped when using the CH button to browse the channels but can be watched by selecting in the channel list or using the number buttons Picture Setting Press the MENU button once to enter CHANNEL setup r menu and press the A V button to select PICTURE the BEL Standard screen will display as shown CA Press the ENTER or gt button to enter the menu In the PICTURE setup menu press the A V button to select the desired item Press the MENU button to return to the previous menu Press the EXIT button to exit Picture Mode Press the A V button to select Picture Mode and press the lt P button to select Standard Mild User or Dynamic Contrast Press the A V button to select Contrast and press the lt gt or ENTER button to enter the contrast adjusting bar Press the lt P button to adjust the difference between the brightest and darkest regions of the picture Contrast CED 0 23 TV Operation and System Setup Brightness Press the A V button to select Brightness and press the lt gt or ENTER button to enter the brightness adjusting bar Press the lt P button to darken or brighten the picture Color Press the A V
43. m the apparatus 13 Only use attachments accessories specified by the manufacturer 14 Useonly with the stand tripod bracket or table specified by the manufacturer or sold with the apparatus 15 Unplug the apparatus during lightning storms or when unused for long periods of time 16 Referall servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Note Do not touch the color TFT LCD screen directly by hand DVD Manufacturing License Agreement This product incorporates copyright protection technology that is protected by U S patents and other intellectual property rights Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Reverse engineering or disassembly is prohibited View of Unit Left Side Panel f ee Pil PLAY PAUSE Fs co Le 1 4 EJECT button Press to eject the disc from the unit 2 mSTOP button Press to stop disc playback in DVD mode 3 Pil PLAY PAUSE button Press to start disc playback and press it again to pause playback in DVD mode 4 Disc Tray Slot Insert disc into this slot
44. mbol indicates that dangerous voltage instituting a risk of electric shock is present within this unit This symbol indicates that there are important operation and maintenance instructions in the literature accompanying the appliance CLASS1 Caution Laser radiation when open Do not stare into beam LASER PRODUCT Caution use of any controls adjustments or procedures other than those specified herein may result in hazardous radiation exposure Caution 1 The product contains a low power device In order to ensure the safety of the laser device do not remove any cover and attempt to repair the unit If any service is needed please contact the distributor or its authorised service centre 2 Toreduce the risk of electric shock do not remove the cover back No user serviceable parts inside Refer servicing to qualified service personnel Unplug the product from the wall outlet before servicing or when it is unused for a long period of time 3 The manufacturer will not be held responsible for the damage caused by any substitutions and modification of the product without authorisation from the manufacturer s or authorised service agent WARNING 1 Theapparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus 2 Theapparatus shall be connected to a MAINS socket outlet with a protective earthing connection The images in this manual are for
45. me Set a time to end recording in the future End Date The end date should be later than the start date Set a time to end recording in the future End Time The end time should be later than the start time Only one program can be recorded in the same period of time Mode Choose either Once Daily Weekly 6 After setting press the ENTER button to confirm and the Recorded Schedule List will display as shown below RECORDER SCHEDULE LIST 02 May 2009 14 50 Start Date End Date Program Ti TF lt The scheduled program will be recorded automatically at the time you set lt You can schedule more recordings and the scheduled programs will be listed in the Recorded Schedule List lt gt While in Recorder menu you can also press the green button to enter the Recorded Schedule List 7 Pressthe A V button to select desired title and press the red button to delete it 8 Pressthe EXIT button to exit NOTE lt While TV is in standby mode unit will start schedule record in standby mode It will not output any picture or sound The power indicator will flash red and blue to indicate that there is a recording lt The recording will end automatically at the End Time you set 37 EPG Function In DTV Mode Only This system has an Electronic Program Guide EPG to help your navigation through all the possible viewing options The EPG supplies information such as program listings start and end times for all available
46. mer Auto Sleep Time Zone Off Off Off Off Victorea GMT 10 lt The clock will go to the default status after power off and re plug in the power again 27 TV Operation and System Setup Off Time Press the A V button to select Off Time and press the em Clodk Repeat 4 of p ENTER or gt button to prompt a information box as Lus dew we 4 o D h denas On Time ae a snown T Seen Timer Minute Press the A V button to select Repeat Hour or Minute a Auto Sleep press the lt P button to set ee ene one Press the ENTER button to confirm after selecting Close On Time Press the A V button to select On Time and press the Lon Clock ENTER or gt button to prompt a information box as Hour shown A Sleep Timer ci M AA Volume 4 Press the A V button to select Activate Hour Minute Auto Sleep Time Zone Mode Volume or Mode press the lt gt button to set Press the ENTER button to confirm after selecting Close Sleep Timer Press the A V button to select Sleep Timer and press the lt P button to select the time to turn off the TV Auto Sleep Press the A V button to select Auto Sleep and press the lt P button to select On or Off Time Zone Press the A V button to select Time Zone and press the lt P button to select desired time zone Option Setting Press the MENU button once to enter CHANNEL setup hans Language English menu and press the A V button to select OPTION the Audio Lang
47. normal conditions such as excessive temperatures or humidity or entry of liquids objects or creatures into the product 13 Noone is authorised to assume any liability on behalf of TEAC or impose any obligation on it in connection with the sale of any equipment other than as stated in this warranty and outlined above 14 TEAC reserves the right to inspect and verify whether the product is exhibiting a major failure as claimed by customers retailers 15 LCD dead pixel policy please contact TEAC Customer Support Hotline on 1300 553 315 for assistance Table Of Contents Important Safety Instructions eroe E ER EYE CHUTE REC Ep EN UE YR EI QU FE VOH FAS FE DR DID PECORE PRO HM dde eani anaia oona 2 VICW RBS ae 4 ettside exe alc beeen meme erere m Dux LU dx I Lei Md ND E M 4 FORCEJO asa cuales Aste dn LA mM A LL Ae ilt 5 EETA E E axo E hx tC E d M I d a iM M E IM tL d 6 Special Feature of DVD Module eL 7 DISC INFORMA GR me 8 Remote CONE ON sisiissciscsscedcstccsenssidecescsiucsesanedecuscsicuceosedecaususs E dh ousbatotededevad ee snassnduenas duseastnnns 9 Remote Control DEaWwImic us sss sis CORR causes aN nde vto bo qd educ tuac a e eT e ded d pd 9 Preparation or REMIOLE CONTO enses Hv eb ERR EE d e b ut vetta a a P abe pe b uR d 12 WET ave Romi enel cedo aid ge NT DD LL LEN T 12 cicipESoDgIssDI LN D M 13
48. ns on the remote and press ENTER to confirm or press lt to cancel setting After ENTER you return to the main menu using lt 49 Dolby Digital Page Dual Mono STR Dynamic Dual Mono 1 4 1 Setup Dolby Digital Page Dual Mano STR Dynamic Set DRC Off HDCD Setup Page Filter Off Filter Video Setup Page Quality DivX VOD Go To Video Quality Setup Page Stereo L Monao A Mone Mix Mona Off A DVD Setup Menu Video Quality Setup Sharpness Sharpness MID High This menu allows the settings for the sharpness of the Brightness 00 TRU picture High Medium or Low Select Low for a soft image ica Vr a and High to improve a blurry image Sharpness Brightness and Contrast Brightness HH 0 Used to set the brightness and contrast of the image to conform to the surrounding light and according to individual preferences Contrast VILLE in 0 DivX VOD Setup For receiving the DivX Video On Demand registration codes Video Setup Page You can use this code for downloading a DivX video The Quality DivX VOD OK downloaded video can only be downloaded onto this device The code is automatically updated after the DivX video is played Navigate to the OK option and display the information using ENTER Press the ENTER button again to exit the option s setting Get DixX Registration Code Preference Page This function is allowed to set when there is no disc in the d
49. ntres will use their best endeavours to complete product repairs within a reasonable period based on available resources and workload during the time when service is requested and performed 9 Refurbished parts may be used to repair the product In the case of a replacement the product may be replaced with a refurbished unit of the same type or if one is unavailable a similar refurbished model with equal or better features amp specifications 10 Please be advised that if the product presented for repair is capable of retaining user generated data the data may be lost during servicing Customers are strongly encouraged to back up all important information data before sending the product in for service repair 11 Service will be provided only during normal business hours and under safety conditions and circumstances TEAC and its authorised service agents can refuse any repair if safety in relation to OH amp S becomes a concern to its staff or authorised service agents personnel 12 The warranty is void and warranty claims may be refused subject to the Australian Consumer Law if a The product was not transported installed operated or maintained according to manufacturer instruction or b The product was abused damaged tampered altered or repaired by any unauthorised persons or c Product failure is due to accidents during use installation or transit power surges use of defective or incompatible external devices exposure to ab
50. ppear on the screen as shown on the right DVD 2 This menu also appears when pressing the CARD button Media in DVD mode 3 Pressthe A V button to select DVD and press ENTER button to start disc playback 4 Pressthe A V button to select Media and press ENTER button to enter Press the 4 button to select USB memory playback or the SD MS MMC playback and press the ENTER button to start Please see the below figure 00 00 00 00 H 001 002 lt Press the A V button to select the folder and press the ENTER button to enter Press the A V button to select the desired track Then press gt PLAY button to start playback lt Press M STOP button to stop playback Press gt PLAY button to start playing from the beginning of the current track Press the lt button to return to the folder menu Notes 1 The screen display will vary from disc to disc 2 Pullout the USB memory or SD MS MMC card directly after the files are played Then the media selecting menu will appear on the screen 46 DVD Setup Menu This is the place where you can arrange all important settings for the cooperation of the DVD with the TV set and other audio equipment General Operating Steps 1 Pressthe INPUT button to change to DVD mode Press the SETUP button on the remote control the settings menu will appear It includes the options General Setup Page Audio Setup Page Video Setup Page and Preference Page Use lt P to select the d
51. r CHANNEL setup menu and press the A V button to select SOUND the screen will display as shown Press the ENTER or gt button to enter the menu In the SOUND setup menu press the A V button to select the desired item Press the MENU button to return Standard Auto Volume SPDIF Output to the previous menu Press the EXIT button to exit Sound Mode Press the A V button to select Sound Mode and press the lt P button to select Standard Music Movie Sports or User Note lt The items Treble and Bass are only available when Sound Mode is set to User Treble Press the A V button to select Treble and press the lt P button to adjust the level Bass Press the A V button to select Bass and press the lt P button to adjust the level Balance Press the A V button to select Balance and press the lt P button to adjust the level Auto Volume Some times different TV stations volume level may be different from each other this function will mornalise audio level form all channels Press the A V button to select Auto Volume and press the lt P button to select On or Off SPDIF Output Press the A V button to select SPDIF Output and press the lt P button to select Off AC3 or PCM AD Audio Description Switch Press the A V button to select AD Switch and press the lt P button to select On or Off AD Volume Press the A V button to select AD Volume and press the lt P button to adjust the level Note AD Volume is only ava
52. ring some digital program is added with some extra subtitle For example the subtitle describes the background sound using words and display it on the screen Press the A V button to select Hearing Impair and press the lt P button to select On or Off Note Not all the digital programs have this function Country This item is used to shown the current country Restore Factory Default Press the A V button to select Restore Factory Default and press the ENTER or gt button to prompt a cel confirmation information box as shown Press the lt b button to highlight Yes or No press the ENTER button to reset the settings to their default status or cancel Note This operation will clear all channels and user settings 29 TV Operation and System Setup OSD Time Out This item is used to set the duration of the OSD on the screen Press the A V button to select OSD Time Out and press the lt P button to select desired time DVRFile System Press the A V button to select DVR File System and press the or ENTER button to enter the sub menu as Select Disk i Check DVR File System shown Press the MENU button to return to the previous menu Press the EXIT button to exit Select Disk Select a disk to store the recorded file Press the A V button to select Select Disk and press the or ENTER button to prompt a sub menu as T n 5 Select Disk shown M i Disk c The item Disk is highlighted and press the lt gt
53. signal source Press INPUT then direction buttons to select Composite or S Video mode and then press the ENTER button to confirm lt The L R audio input jacks can be used in both AV and S VIDEO modes Connecting an External AV Signal Source YPbPr Use AV cables to connect an external AV signal source to the Y Pb Pr Component input jacks on the rear panel of the unit a21nos jeuBbis Ay Eu191X3 After connection turn on the power of the unit and the external AV signal source Press INPUT then direction buttons to select Component mode and then press the ENTER button to confirm 14 System Connections Connecting to an External AV Signal Source HDMI Follow the figure below to connect an HDMI signal source to the HDMI jack on the rear panel of the unit External AV Signal Source After connection turn on the power of the unit and the external AV signal source Press INPUT then direction buttons to select HDMI mode and then press the ENTER button to confirm Connecting to an External AV Signal Source AV Output Use the AV cables to connect the external AV input device to the AV output jacks on the rear panel of the unit External AV Signal Source After connection turn on the power of the unit and the external AV signal source Press INPUT then direction buttons to select the corresponding mode and then press the ENTER button to confirm 15 System Connect
54. to select enter the source selecting menu press the A V direction buttons or press the INPUT button repeatedly to select desired mode and press the ENTER button to enter the selected mode MENU button Press to enter or exit the setup menu Direction buttons A V lt P In the setup menu press the A V button to select a desired item and press the lt gt button to adjust or set ENTER button Press to confirm your operation in setup menu VOL button Press to increase or decrease the volume 0 9 Number buttons Press to select numbers such as TV channel C2 button In ATV or DTV mode press to return to the channel previously viewed STEREO button Press to select sound track in ATV mode DISPLAY button Press to display the reference information of the current mode PICTURE button Press repeatedly to select the picture mode Standard Dynamic User or Mild DVR LIST button Press to display the recorded file list ATV button Press to select ATV mode DVD button Press to select DVD mode GUIDE button Press to display the Program Guide menu in DTV mode 4 6 button Press to eject the disc out in DVD mode In DTV mode press to start to record the current viewing program m STOP button Press to stop disc playback in DVD mode K4 Next Skip button Press to skip to the previous or next chapter track in DVD mode In Program Edit menu press the yellow button to move a channel an
55. uage English screen will display as shown aaki eee uae Hearing Impair Off Press the ENTER or button to enter the menu In the OPTION setup menu press the A V button to pes gt Restore Factory Default select the desired item Press the MENU button to return to the previous menu Press the EXIT button to exit Language Press the A V button to select Language and press the lt P button to select desired language 28 TV Operation and System Setup Audio Language Press the A V button to select Audio Language and F Bm Language press the ENTER or gt button to prompt a information em box as shown ied UEM Secondary English P Press the A V button to select Primary or Secondary Hearing Imp ce press the lt gt button to select desired language Restore Factory Default Press the ENTER button to confirm before selecting Close Note this function is only available in DTV mode Subtitle Language Press the A V button to select Subtitle Language and anaiai press the ENTER or gt button to prompt a information m ES Audio Langui Hearing Imp Close EE Secondary 44 English P box as shown Press the A V button to select Primary or Secondary N press the lt P button to select desired language em gt CESEREPUS tip Derautt Press the ENTER button to confirm after selecting Close Note this function is only available in DTV mode Hearing Impair For the people with poor hea
56. utton Press to select DTV program playback or Radio program playback in DTV mode gt PLAY button Press to play a disc in DVD mode Il PAUSE button In DVD mode press to pause playback and again to resume lt gt button Press to search backward or forward in DVD mode In Program Edit menu use the red button to delete a channel and use the green button to rename a channel see P22 23 for details In teletext mode they are the teletext colour buttons SETUP button In DVD mode press to enter the DVD setup menu In ATV mode press to display or close the teletext MENU button under DVD mode Press to enter disc menu in DVD mode In teletext mode press to disable teletext display for page updates and press again to resume SUBTITLE button In DTV DVD mode press to select alternate subtitle languages during view playback of a DTV program or multiple language DVD disc In teletext mode press to display P 100 Note Subtitle and teletext is only available if the service is provided by broadcaster Remote Control 11 12 13 14 15 16 17 18 19 20 21 22 AUDIO button In DVD mode press to select the audio language or audio track In teletext mode press once to display the concealed information such as solution of riddles or puzzles press again to remove the riddles answers from the display CH LIST button Press to display the channel list INPUT button Press
57. you press the button while playing unit will resume to live DTV 35 DVR Function Schedule Recording Schedule record is a function which allows you to record future program You can first set up a schedule record then unit will record the program when the program is broadcast It will stop recording when the program finish 1 Pressthe GUIDE button to display Electronic Program Guide menu as shown DTV 800 New Youk Police Juciaire Mes deux LES NOUVELLES PUSSYCAT LES NOUVELLES PUS JEUX O New Youk Police Juciaine m ON PLAGE DE LECTURE BALKO Balko suspect un BALKO Le tresor agsps amp 2 Select your desired TV program and press the RECORD C button to enter the Recorder menu as shown 02 May 2009 14 5 start Date 2008 08 06 Start Time 14 45 End Date 2008 08 06 End Time a 3 From here you can modify the start and end date time of your record schedule by using the lt gt direction button i T Aisi A A once Month b 4 usethe A V direction button to select date time to SCALE Date Sat 02 gt End Date End Time change Hour Minute 36 DVR Function 5 Usethe A V button to select desired item and press the ENTER button to enter Program Select a program Set a date to start recording in the future SHN ate The start date should be later than the current date Set a time to start recording in the future Start Time The start time should be later than the current ti
Download Pdf Manuals
Related Search
Related Contents
Montage- und Betriebsanleitung Operation and Assembly Instructions MANUAL TÉCNICO XVIII CAMPEONATO Copyright © All rights reserved.
Failed to retrieve file