User's Manual
Contents
1. r fleetminde COPYRIGHT Fleetminder 2013 Publication Date March 2013 Lite TABLE OF CONTENTS 1 0 Introduction 2 0 Packaging Contents 3 0 Precautions 4 0 Operating requirements 5 0 Basic Functions 6 0 Wiring diagram 7 0 Theory of SMS operation 8 0 SMS setup 9 0 GPRS Online Tracking 10 0 LED Troubleshooting 11 0 Technical Data 12 0 Warranty Information fleetminder User s Manual User s Manual Page1 fleetminder 1 0 Introduction Congratulations on your purchase of Fleetminder Fleetminder is an exciting Australian designed product that enables you to personally take control of the security and tracking of your assets The Fleetminder system works independently but has Inputs and Outputs which means it can be connected to any existing alarm system for alarm notification or additional triggers The Inputs and Outputs can be configured to control a range of different features The Fleetminder has a variety of different ways of reporting an event or reporting to a command The Fleetminder is fitted with a GSM GPRS module that allows for GPRS and SMS reporting When using GPRS the Fleetminder will log data on our tracking website for easy reviewing by fleet managers or owners Fleetminder reporting can be set to many different intervals for tracking accuracy For SMS reporting the Fleetminder can either report the co ordinates to the tracking website or can report a link for a map that2. AIRCRAFT SAFETY When transporting this equipment by air ensure the unit is totally disabled by removing the SIM card from the SIM card slot And ensuring the Red power LED is switched off If the Red LED is flashing press and hold reset button for 4 seconds until all lights switch off OTHER PRECAUTIONS OUTPUTS The outputs are rated at 300mA max As default the outputs are set to trigger a low ground Due to outputs being limited to current we recommend using outputs to control relays The outputs can be configured for a latch permanent switch circuit a pulse 800mS pulse circuit normally used for central locking circuits or cycle circuit normally used for flashing indicators NOTE Cycle will only last for 30 seconds The outputs are most commonly used for unlocking doors sounding horn and disabling starter motor but can be used for almost anything INPUTS The inputs can be connected to almost any electronic circuit however please note that there are 2 positive triggers 12V or 24V inputs and 1 negative trigger GND input Refer to the Installation manual for more information fleetminder User s Manual Page 5 fleetminder 4 0 OPERATING REOUIREMENTS ENVIRONMENT Do not install Fleetminder in direct sunlight or directly under any areas exposed to direct sunlight or extreme heat Fleetminder incorporates sensitive electronics and is to be installed in the vehicles cabin only Kee
3. 2222 22222E22222 22 22 NAME is the number for the rectangular geofence from 5 9 1111 11111 and E11111 1111 are valid point1 Coordinates 2222 2222 and E22222 2222 are valid point2 Coordinates NAME is the name of the geofence default Rectngular GEOFENCE 10 29 are Point SETGPO NL Sets the outputs N for Latch SETGPO 1L Will set output 1 for Latch SETGPO 1L Will set output 1 for Latch SETGPONP Sets the output N for Pulse This is default setting SETGPO 1P Will set output 1 for Pulse SETGPO 1L Will set output 1 for Pulse SETGPONC Sets the output N for Cycle SETGPO 1 C Will set output 1 for Cycle SETGPO 1 C Will set output 1 for Cycle LABELGPO N X Renames the label heading for an output Up to 16 characters for all 3 inputs LABELGPO N LABELGPO 1 Siren will set the label of output 1 to Siren where N is the number of the output and X is the name of output QUERYOUTLABEL N Queries the Label settings for the Outputs No default QUERYOUTLABEL N where N is the input number QUERYOUTLABEL 1 will request the LABEL heading for Output 1 input 1 to 7 GPO N ON Enables Disables outputs where N is the input Default setting is all GPO 1 ON Will trigger output 1 to switch on number outputs switched off GPO N OFF Enables Disables outputs where N is the input Default setting is all GPO 1 OFF Will trigger output 1 to switch off number outputs switched off GEOFENCE To set and enable disable geofencing GEOFENCE X Used to set u
4. Note Device and antenna shall be installed on distance greater than 20 cm from human body FE CEA Page 28 fleetminder User s Manual
5. Current GPRS online 60MA Current 80mA GPRS transmission Current Peak 120mA FLEETMINDER COMMUNICATION fleetminder User s Manual GPRS SMS ENVIRONMENTAL Operating Temperature 20 C to 55 C Storage Temperature 40 C to 85 C Page 26 Lite GPS SPECS Channels 48 verification channels Tracking 168dBm Frequency L1 1575 MHz Position accuracy Horizontal lt 2 5m CEP autonomous lt 2 0m CEP SBAX Time to first fix Hot start 1 lt 1s Warm start 2 lt 32s Cold 3 lt 35s NMEA message GGA GSA GSV VTG RMC GLL switchable fleetminder User s Manual User s Manual Page 27 fleetminder 12 0 Warranty The Fleetminder is guaranteed for a period of twelve months from date of purchase against defects in materials and workmanship under conditions of normal use To obtain warranty support return the unit together with proof of purchase to the place of purchase LIMITATIONS OF WARRANTY Fleetminder accepts no responsibility for any actions of the purchaser or user of the eguipment where the eguipment is not used for its intended purpose and isn t installed in accordance with the instructions provided in this manual Fleetminder does not accept responsibility of any conseguential effects or breaches resulting from the use of this eguipment in a manner which constitutes a criminal act or breach of privacy
6. been disabled this can be done in the security settings in a mobile phone If the yellow light is on but not flashing please ensure that you have the correct APN username and password set for the network The APN is usually different for each network provider and can be found by calling the telecommunications provider some telecommunications providers require a username and password to be declared please ensure that you have these details The APN username and password can be set only from the primary defined phone number please refer to the Users Manual for setting primary identity The primary phone needs to send commands for setting the APN username and password these commands can be found in the command list in the users manual s GPS indicator This led will stay on when there is a valid GPS fix When there is no GPS reception the led will not be lit GREEN LED GPS Troubleshooting Indicator Please ensure that the GPS antenna gold connector is connected and that it is mounted in a suitable spot with clear view of the sky The vehicle must be outside to be able to get a GPS fix fleetminder User s Manual Page 25 LOK K A fleetminder 11 0 Technical Data FLEETMINDER SPECIFICATIONS Enclosure Dimensions 82 L 61 W 21 H Weight 90g Modem Specs Frequncy range 850 900 1800 1900 Electrical DC Supply voltage 12V OR 24V DC Tolerance voltage 9V 36V
7. every time that the input3 wire is released from 12V or 24V Input event will send an alert message via SMS and GPRS to advise that the vehicle is in trouble This will occur when the Help button has been activated Occurs when the main system voltage on the Red wire goes below the amount defined by the owner for more than 5 seconds Occurs when the vehicle exceeds the speed limit as defined by the operator Occurs when the vehicle enters or leaves one of 30 areas as defined by Owner Occurs when the vehicle is moved whilst Fleetminder Towaway feature is armed Occurs when the periodic report timer has lapsed fleetminder User s Manual Cite User s Manual 8 0 SMS Setup unless pre set from manufacture Please make sure you have activated your SIM card and have disabled the message bank service and SIM PIN number before proceeding Ensure red LED indicator is on and the yellow light is either on or flashing If not then check wiring 8 1 Register your phone as the primary identity Send SMS PIN 0000 Wait for response 8 2 Now change your PIN The factory default pin or other defined pin as with all other commands can only be changed from the primary identity To change the pin Send SMS NEWPIN 1234 where 1234 is your new PIN Wait for response fleetminder User s Manual Page 13 fleetminder 8 3 Set secondary identity only receives events The secondary identity is us
8. Default is off SPEED KKK where KKK is the speed in Kmh SPEED 00 SPEED 65 will trigger when the speed of vehicle goes over limit is exceeded disables Speed alerts 65kmh STATUS Reports back with the features that are No Default enabled on the Fleetminder SYS Reports back additional unit parameters No Default including the Voltage GPS and GSM signal strength etc TOW XXX ON Enables the tow away feature Default is off TOW XXX ON where XXX is the distance in metres TOW 100 ON will turn the Tow away feature on with a distance of 100 metres when ACC is switched on it will disable the tow away reporting This is so an SMS does not have to be set every time TOW X OFF Disables the tow away feature Default is off TOW X OFF where X is the distance in metres TOW 0 OFF will turn the Tow away feature off VOLTS VY Sets and enables the low voltage alert Default is off VOLTS VY where VY is the voltage in percentage VOLTS 80 will set the low voltage warning to 80 of 12V in a 12V application 12V is 100 and 24V application 12V application 9 6V 24V is 100 for use in 12V and 24V systems VOLTS OFF Sets the VOLTS command to disable after it has Default is on Turns feature off after low voltage alert has been triggered been triggered LOCATION LOCATION command when sent alone will report the current location GPRS X To turn GPRS mode off SO only SMS mode will GPRS ON or GPRS OFF GPRS OFF will turn GPRS reporting off If sms event report
9. INEVENTON will enable the sms reporting of events events alert tow away alert gps antenna unplugged conditional in geofence voltage alert and input triggers options Such as Goefences or input triggers NOTE Panic depending on GPISMS command and only AD1 alert can not be when set to Temperature for Max and Min turned off for SMS reporting reporting Will not send alerts for G trigger AD input 1 and 2 trigger and stopped report SMSEVENTOFF Command to disable the SMS reporting for Depends on the GPRS Will disable SMS reporting for events 138 tow SMSEVENTOFF will disable all the sms reporting of events or events from the unit So basically to be able to connection away alert 101 overspeed 142 stopped input triggers choose whether to have sms event reporting GEOFENCE alerts Input TRIGGERS depending on conditional in options Will still respond to SMS commands GPISMS command VOLTS reporting NOTE Panic alert can not be turned off for SMS reporting MAP Command to allow users using the SMS No default MAP will invoke a response from the unit that will provide a function only to view their vehicle on a map on URL link that can be viewed through any GPRS phone their mobile phone using GPRS REBOOT This command is used when a unit needs to No default REBOOT will cycle the power on the device to make it restart be restarted in case it needs to be restarted GREPORT X This command is used for setting up the No default GREPORT X wher
10. REPORT 00 disables reporting GEOSTATUS OUT Displays summary of all the Geofences that are Invoked by user GEOSTATUS OUT will respond to primary number with the OUT outside the perimeter geofences that are outside the perimiter GEOREVIEW X Displays details of Geofence X for review Invoked by user GEOREVIEW 3 will respond to the primary number with GEO3 set 3452 76282 E45362 5638 Bank 0 P where is no radius and P is Point geofence GEONEAR Returns the nearest geofence to the location Invoked by user of the vehicle REPORT MMM SS Used for periodic reporting of the location Default is off REPORT MMM SS where MMM is number of REPORT 02 30 will report every 2 minutes and 30 seconds INTREPORT T S D Used for seeing Intelligent reporting It is speed and ign dependent Default is off INTREPORT TT SS DDDD where TT is the time in second when vehicle is moving and IGN is ON SS is the threshold moving speed and DDDD is the reporting time when vehicle is below threshold speed and IGN is OFF INTREPORT 60 4 1800 Will set the moving and IGN ON reporting time to 60sec with the threshold speed of 4kmh Otherwise if the IGN is OFF and if speed is below 4kmh the unit will report every 1800sec be enabled INTREPORT OFF Used for seeing the Intelligent reporting OFF No Default INTREPORT OFF will turn Intelligent reporting off SPEED KKK To notify the primary identity when the Speed
11. Report on the selected vehicle over a specified date range The activities can include Ignition on off panic alert input triggered etc VEHICLE SITE REPORT This function allows the user to view the Sites that the vehicle fleet has visited on a per vehicle basis per site basis or a combination of both Page 22 fleetminder User s Manual Life User s Manual VEHICLE MILEAGE REPORT This function returns the user with a Mileage Report on a specific vehicle over a specified date and time range VEHICLE STOP REPORT This function returns the user with a Stop Report on the selected vehicle over a specified date and time range VEHICLE TRIP REPORT This function returns the user with a Trip Report on the selected vehicle over a specified date and time range VEHICLE OVER SPEED REPORT This function returns the user with a Over speed Report on the selected vehicle over a specified date and time range NOTE Some reports require input1 to be connected to IGNITION wire for accuracy fleetminder User s Manual Page 23 Wf a ce ag fleetminder 10 0 LED Troubleshooting The Fleetminder LITE has LED indicators on the front of the device that can be used for diagnosis of the device They explain the functionality of the device by their status explained below On solid state Unit powered by main power Flashing Unit operating under bac
12. can be viewed on any GPRS mobile phone Unlike other tracking products on the market Fleetminder use by SMS does not require a subscription to a base monitoring service for basic functions However in most cases we recommend that fleet managers subscribe to our web service The vehicle history is available in a range of formats online and retrievable at any time via our optional subscription service NOTE For the full features of the online tracking feature please refer to the Online tracking manual Page 2 fleetminder User s Manual Life User s Manual 2 0 Packaging Contents Before commencing installation please make sure all components listed here are accounted for In the packaging you should have 1 x Fleetminder LITE unit 1 GPS antenna 1 GSM antenna 1 Main wiring harness 1 Panic Button 1 Programming LED SIM card can be supplied on request has to be GPRS enabled for online tracking Optional accessories can be supplied on request fleetminder User s Manual Page 3 fleetminder 3 0 PRECAUTIONS IMPORTANT Make all wiring connections to the vehicle and antenna connections to the correct sockets BEFORE connecting the main plug to Fleetminder Refer Installation manual It is strongly recommended that the units SIM card is first registered contains credit and is tested before installation is commenced Testing will reguire a valid sim service For GPRS online tracking the sim ca
13. completing the installation that the antenna is secured firmly in place Before picking a location in your vehicle for the GPS antenna it is best to first connect the GPS antenna to the Fleetminder and apply power Shortly after powering on Fleetminder you will observe the green satellite LED on the unit turn on this means the unit is receiving GPS data If this does not happen place the antenna on the roof of your vehicle making sure that your vehicle is outdoors Wait until the LED comes on and stays on This now indicates Fleetminder has a fix on your vehicles location Please be patient as with a cold start first power up this process of satellite acquisition can take up to 5 minutes in worst case In some cases where the control of the Fleetminder is set to SMS as a default and the unit has started up successfully RED and GREEN lights on with the YELLOW LED flashing or still you are able to find out the GPS status by simply sending a SYS sms command from the Primary declared phone number see command list to see how to set this and for further instructions on the SYS command In the reply message you will see the status of the GPS fleetminder User s Manual Page 7 fleetminder MINIMAL INSTALLATION If you would like to use Fleetminder for GPS SMS tracking only then all you need to do is simply connect Fleetminder to a constant 12volt or 24 volt source and place the GPS GPRS antenna in a suitable locatio
14. e X is the G rating GREPORT 2 will set the unit to report when it senses a G acceleration or deceleration reporting using rating of above 2G the crash sensor CRASH N G Set parameter of crash sensor No default N ON OFF stands for ON OFF CRASH ON 2 G Stands for acceleration ON means enabled 2 means the acceleration is 2G fleetminder User s Manual Life User s Manual 8 6 SMS message format explained The following information displays the format of an SMS message received from the device The Message parameters are separated by a comma and each part is explained below SMS FORMAT Fleetminder Command Current 09 080527 114236 51234 7536 E11234 5678 000 44000000 CFG LOCATION LABEL FLEETMINDER The Fleetminder label is pre set for online tracking and will be unique for every device This usually consists of a 4 digit number that is used as a unique identifier EVENT COMMAND The event includes the reason that the SMS message was sent In most cases when a command has been sent to the device it will respond with COMMAND otherwise if an input trigger has occurred it will respond with the Input name such as ACC or DOOR Note Input names can be set separately refer Command list fleetminder User s Manual Page 19 fleetminder GPS FIX CURRENT Current indicates that the GPS data presented is current and indicates that the location provided is where your asset is now Alter
15. e from gaining access to your Fleetminder and potentially your assets For event reporting such as geofencing or alarm trigger a secondary identity can also be set NOTE secondary identity cannot control the unit it can only get event alerts It is even better if the phone number of Fleetminder is kept confidential along with the PIN code that you have for your Fleetminder ALERT EVENTS An alert event is any of the below occurrences which if configured will initiate a SMS or and GPRS response Please note all alert events need to be configured and enabled before they will work Input1 triggered Unconditional input where a label can be set occurs every time that the input1 wire is triggered by 12V or 24V Input1 recovered Unconditional input where a label can be set occurs every time that the input1 wire is released from 12V or 24V fleetminder User s Manual Page 11 fleetminder Input2 triggered Input2 recovered Input3 triggered Input3 recovered Help Volts Speed Geofence Tow Away Report Page 12 Unconditional input where a label can be set occurs every time that the input2 wire is grounded Unconditional input where a label can be set occurs every time that the input2 wire is taken from ground Unconditional input where a label can be set occurs every time that the input3 wire is triggered by 12V or 24V Unconditional input where a label can be set occurs
16. ed for receiving events only not controlling the device Send SMS PH2 61423123456 where 61423123456 is the secondary contact number send PH2 without a number to turn this feature off Wait for response primary identity The Fleetminder will now respond to the secondary identity as well as the primary identity where an event has occured These events can include unconditional events such as input voltage or geofencing 8 4 Send a map to primary phone number Send SMS MAP Wait for response Fleetminder unit will provide a URL link Map can be viewed through any GPRS phone Page 14 fleetminder User s Manual Lite User s Manual 8 5 Command List COMMAND LIST PIN XXXX PURPOSE Pin number security for the access of the Fleetminder Also used for setting the primary identity And firmware upgrade password DEFAULT SETTING OPTIONS PIN 0000 Used to set the primary identity and firmware upgrade password PIN XXXX used to change the primary identity as long as the PIN number is correct EXAMPLE PIN 1234 will check the pin number in the unit and if void will ignore the message but if correct it will change the primary identity to the phone number where the message was sent from NEWPIN Used to change the pin number from the No default NEWPIN XXXX where XXXX is the new 4 digit pin NEWPIN 1234 will change the pin number fro
17. ing is switched off this function should switch it back on fleetminder User s Manual fleetminder COMMAND LIST PURPOSE DEFAULT SETTING OPTIONS EXAMPLE SETAPN XXXXXXXX max Where XXXXXXXXXXX up to 48 chars is the No default SETAPN SETAPN internet will set the APN to internet 48 chars APN Access Point Name Telecommunications internet will set the APN provider to internet SETUSER UUUUUUU Where UUUUUUUU is the username and No default SETUSER neltronics access will set the Username as PPPPPPPP PPPPPPPP is the password the username Neltronics and the and password are seperated by a space IF password as access SETUSER is sent with no parameters it should set the username and password to nothing SMSALLEVENTON Command to enable the SMS reporting for Depends on the GPRS Will enable SMS event reporting for speed alert SMSALLEVENTON will enable the sms reporting of events events from the unit So basically to be able to connection tow away alert geofence voltage alert input conditional in choose whether to have SMS event reporting triggers depending on GPISMS command G options Such as Goefences or input triggers NOTE Panic trigger AD input 1 and 2 trigger all alerts and alert can not be stopped report turned off for SMS reporting SMSMAINEVENTON Command to be able to control Grouped SMS Default is ON Will enable SMS event reporting for ONLY speed SMSMA
18. kup battery check vehicle RED LED power supply Power Indicator Off Means there is no power to the unit check fuse and connection of the red and black wires Flashing Means unit is registered on the network and connected to the tracking server pave On but not flashing Means the unit is registered on the network but Indicator not connected via GPRS check APN username and password refer network provider for the APN username and password APN setting correct but still not flashing means that there is no credit on the account if pre paid is used or the account is disabled check with network provider to ensure the bill is up to date To troubleshoot remove the sim card from the device and put it in a phone Try to send a message If the problem persists please call your Fleetminder manager Off Means the device is unable to register onto the network Please ensure the sim card is inserted correctly And that the sim card is valid and activated In case there is a pin on the device please ensure that the pin is removed this can be done when a sim card is inserted in a phone by accessing the security menu s GREEN LED GPS Indicator On Means that the device is able to get a current GPS location Off Means that the device is unable to get a current GPS fix Please check the antenna location and ensure that it has a clear view of the sky Page 24 fleetminder U
19. m the unit as default setting number long as the message is sent from the primary identity PH2 XX Sets the secondary number for event No default PH2 XX where XX is the secondary phone number PH2 0412345678 will set the secondary number to 0412345678 reporting note PH2 without the number will disable this feature LABELIN N X Renames the label heading for an input No default Up to 16 characters for all 3 inputs LABELIN N X LABELIN 1 Starter will set the label of input 1 to Starter admin only where N is the number of the input 1 3 and X is the name for the input QUERYINLABEL N Queries the Label settings for the Inputs No default QUERYINLABEL N where N is the input number input QUERYINLABEL 1 will request the LABEL heading for Input 1 1 to 3 DELAYIN NT To set a delay timer on an input trigger No default Used to set a delay for input triggering where N is DELAYIN 2 20 will set the input 2 delay time for 20 seconds the number of the input 1 3 only and T is the before sending an alert delay time in seconds GPI N X GPRS Only To enable or disable the input No default This feature is to enable or disable the Inputs GPI 2 ON will enable Input 2 GPI 2 OFF will disable Input 2 Where N is the number of the Input and X is the status On or OFF GPISMS N X SMS Only To enable SMS alerting for a defined input No default This feature is used to enable or disable SMS alerting GPISMS 2 ON will enable sms alerting for Input 2 fo
20. n The Fleetminder system should be installed at least 60cm 2 feet away from your vehicles wiring and electrical systems to prevent interference The GSM signal strength can be identified by using the SYS sms command sent from your primary controlling phone number refer to the command list Page 8 fleetminder User s Manual Lite User s Manual 5 0 Basic Functions FUNCTIONS APPLICATIONS applications include ACC Alarm trigger and GPS GPS receiver will output a complete position velocity and time PVT solution in the NMEA Version 3 0 protocol GPRS SMS GPRS uses standard TCP or UDP communication protocol SMS can be turned on or off 4 inputs 2 controllable inputs most common INPUT1 positive trigger usually used for Ignition Trigger INPUT2 negative trigger 2 reserved inputs usually used for flashing lights disabling starter motor and unlocking doors door trigger Help switch trigger AUX analogue input 1 output 1 Gray wire 300mA Pulse Latch Cycle Programmable Help Switch Will send a report when the Help switch has been activated has to be programmed with number to report number to Standard Reporting Automatic report for tracking purpose Intelligent Fixed time report Intelligent Fixed distance report Event Report SMS and GPRS Temperature report when using the optional Temp Sensor Speeding report Low battery report Geo fence trigge
21. natively if your asset was outside and then went under cover such as your vehicle being driven into a garage Then this field will display LAST In this case the location and the time of your Fleetminder the second before it went under cover is recorded Both the CURRENT and LAST messages should be considered with the UTC time given in the next line GPS SATELLITE COUNT Numbers above 5 usually indicate good signal UTC DATE TIME 080527 114236 0 This line contains the UTC date and time An example is 80527 114236 This reads the date as vear 08 month 05 day 27 format and the time 11 hours 42 minutes and 36 seconds or 11 42 36 AM You will need to add your time difference to determine your local time CO ORDINATES 51234 7536 E11234 5678 This line presents the latitude and is in the form dd minutes minutes eg S1234 7536 and the longitude and is in the form ddd minutes minutes eg E11234 5678 SPEED 000 If your vehicle is stationary then this line will show 000 However if your vehicle is moving the exact speed will also be detailed Page 20 fleetminder User s Manual Life User s Manual UNIT STATUS 44000000 The last line 47000000 Is irrelevant for SMS reporting but will always appear as a summary It confirms the message in a ASCII format to be recognized by the tracking server It is kept in the reporting message for Status confirmation RESPONSE CFG LOCATION This is the
22. nces do not need a radius EXXXXX XXXX are valid Coordinates NAME is the name of the geofence GEOFENCE X HERE Used to set a radius geofence to the current No default GEOFENCE 0 3 HERE NAME DISTANCE or GEOFENCE 1 HERE Home 250 This will set The Geofence 1 to the NAME DISTANCE location GEOFENCE 10 20 HERE NAME for point geofence current location with the name Home and this will be set to a radius of 250m in a geofence 250metres around the point POINT XX To see the distance from the current location Invoked by user POINT where XX is a set point geofence geofence POINT 13 will report the distance between the current to a set geofence 10 30 location and the GEOFENCE 13 GEOALLON Enables all the Geofences No default GEOALLOFF Disables all the Geofences No default GEOON X Enables a particular Geofence No default GEOON 0 29 GEOON 2 will turn only Geofence 2 on GEOOFF X Disables a particular Geofence No default GEOOFF 0 29 GEOOFF 4 will turn only Geofence 4 off fleetminder User s Manual Lite COMMAND LIST OUTPUTS PURPOSE To set enable the outputs User s Manual DEFAULT SETTING OPTIONS EXAMPLE GEOSTATUS IN Displays summary of all the Geofences that IN inside the perimeter Invoked by user GEOSTATUS IN will respond to primary number with the geofences that are inside the defined perimiter of the Fleetminder minutes for periodic reporting SS can be used for seconds
23. p circular Geofencing where X No geofences set as GEOFENCE 0 3 are Circular GEOFENCE 5 9 are GEOFENCE 1 3156 7552E11548 7192 HOME 250 This will set SXXXX XXXXEXXXXX XX is the number for the circular geofence from default Rectngular GEOFENCE 10 29 are Point The Geofence 1 to the location 3156 7552E11548 7192 with XX NAME DISTANCE 0 3 SXXXX XXXX and EXXXXX XXXX are the name HOME and this will be set to a radius of 250m ina valid Coordinates NAME is the name of the geofence 250metres around the point geofence Distance is the distance around the geofence in meters GEOFENCE X Used to set up rectangular Geofencing X No geofences set as GEOFENCE 0 3 are Circular GEOFENCE 5 9 are GEOFENCE 5 3156 7552E11548 7192 S3156 7568E11548 7176 Worksite This will set The Geofence 5 to point1 3156 7552E11548 7192 and point 2 3156 7568E11548 7176 with the name Worksite NOTE there is a space between point1 coordinates and point2 coordinates note rectangular geofences do not need a radius GEOFENCE X Used to set up point Geofencing X is the No geofences set as GEOFENCE 0 3 are Circular GEOFENCE 5 9 are GEOFENCE 11 3156 7552E11548 7192 Office This will set The SXXXX XXXXEXXXXX XX number for the point geofence from 10 29 default Rectngular GEOFENCE 10 29 are Point Geofence 11 to the location 3156 7552E11548 7192 with the XX NAME SXXXX XXXX and name Office note point geofe
24. p the unit installed in a secure location that is to be free of dust and moisture For a stealth install it is recommended that the Fleetminder is kept away from any radio antennas or speakers as it may indicate that there is a GSM network connection present to the vehicle operator POWER Fleetminder operates on a 12 volt or 24 volt supply only If Fleetminder has a voltage higher than the operating voltage applied then the device will fail to operate and could cause internal damage to the unit If the power supplied is below the minimum to operate the unit will send a warning if programmed to do so and may switch to backup battery power See Fleetminder specifications The built in backup power supply allows Fleetminder to continue to operate and alert you if your vehicles battery power is severed The backup battery is float charged by your vehicles electrical system Page 6 fleetminder User s Manual Lite User s Manual GPS ANTENNA LOCATION Fleetminder is able to determine the exact location of your vehicle by the use of the incorporated GPS receiver For the GPS to work most effectively the external GPS antenna must be located in a position with as much view of the sky as possible The GPS Antenna will generally operate through non metallic objects Some suggestions include high up under the dash and below the rear parcel shelf The black face of the antenna is the side which must face skyward Ensure before
25. r a particular input CFGAD N X U D B B This is used to configure the input to No default Used for configuring the state and function of the CFGAD 1 TEMP 50 15 20 will set the input level for AD input 1 Temperature or Analogue input And max output For temp or Analogue with min max values to temperature celsius with the max temp 30 degrees and min setting Where N is the AD input X is the TEMP is used for temperature and AD is used for min temp of 15degrees with debounce time of 20 secs setting U is the max D is the min and B is the analogue voltage input debounce time SETAD N U D B Used to configure the Analogue inputs No default Used to set the reporting structure for the AD inputs SETAD 1 0 5 0 1 20 will set the Analogue input 1 to report Where N is the number of the Adinput U is the when AD1 voltage increases by 0 5V decreases by 0 1V and voltage temp increase D is the decrease and B is has a debounce time of 20 secs the debounce time READAD Used for reading the Analogue input voltage No default Used to report the input voltage of the AD input READAD will read the AD input voltage ADNX Used for turning Analogue inputs off No default Used to turn off AD reporting AD 1 OFF will turn reporting for AD1 off fleetminder User s Manual Page 15 fleetminder COMMAND LIST OUTPUTS PURPOSE To set enable the outputs DEFAULT SETTING OPTIONS EXAMPLE 1111 1111E11111 1111
26. r report Input trigger report e g ALARM ARM ACC inputs etc fully customizable Intelligent report G Force exceeded report History data store hardware 3 000 reports can be saved in unit and read by the server at any time fleetminder User s Manual Page 9 fleetminder 6 0 Wiring Diagram RED LED POWER INDICATOR GREEN LED GPS INDICATOR YELLOW LED GPRS INDICATOR le PANIC BUTTON sov BLACK GND A A 1 0 x1 5A FUSE Temy OPTIONAL TEMP SENSOR ra maa OREEN BLACK CHANNEL 1 OPTIONAL SENSOR PUT RA OUTPUT 1 300 m f YELLOW IGNITION 12 24V L E BROWN inpur2 e NOT AOESKO ES Sao maces MUST BE LVE WALE CRANKING Hr NOTE For further information please refer to the Installation Manual Page 10 fleetminder User s Manual Lite User s Manual 7 0 Theory of SMS operation NOTE The Fleetminder system can use SMS reporting as well as GPRS reporting at the same time refer to command list for setting this event Fleetminder authenticates an incoming text message by comparing the senders details phone number to that of the primary control identity which is stored in the Fleetminder flash memory Therefore the Fleetminder is only able to be controlled by its primary control identity This level of security stops someone els
27. rd must be GPRS enabled When installing the GPS antenna make sure that the coaxial cable does not get bent or crimped Always keep Fleetminder s phone number confidential and account paid up for pre paid services Remember your Fleetminders PIN amp phone number no one else should know them For Online tracking please ensure that the SIM card is GPRS enabled for more information on this please contact your sim card service provider Outputs are NOT recommended for use to directly or indirectly immobilize an operating vehicle Immobilizing a vehicle in motion is extremely dangerous The general purpose outputs can be used to disable the vehicle s starter motor only This device is not to be used for unauthorized monitoring or tracking Do not operate this device where mobile phones or radio transmitters are not permitted Do not operate on aircrafts Do not operate near sensitive electronics such as engine brake or air bag systems ELECTRICAL SAFETY Designed to work from 12 volt or 24 volt DC only Use 5 amp inline fuse EXPLOSIVE ATMOSPHERE The Fleetminder uses the GSM network and it is not advisable to request tracking during refueling at blast sites or at chemical sites etc Page 4 fleetminder User s Manual Life User s Manual MEDICAL EQUIPMENT Some medical devices such as pacemakers may be inhibited by GSM signals Check with a doctor or medical equipment manufacturers for more advice on this issue
28. response to event command In this case the response message was received due to the LOCATION command being sent Every time that a message is sent in query to the Fleetminder it will respond with the command included in the message fleetminder User s Manual Page 21 fleetminder 9 0 GPRS Online Tracking This section explains the GPRS online tracking For further information refer to the Complete Online Tracking Manual available from the help menu on the web interface In most cases when the Fleetminder system is ordered it will automatically be subscribed to our online tracking server Our Tracking server is web based which means it can be accessed from any computer with an internet connection For security purposes a username and password is used The unit automatically reports to the Tracking server and logs all the data for reviewing These reports can then be extracted into different formats such as pdf or printed for reference Real time Tracking is available whilst also being able to use the replay a day feature which will show the activity of a vehicle on a chosen day The Tracking server can provide a variety of different reports whilst also being able to send GPRS commands to control the inputs outputs and reguest further information from the unit The reports that can be viewed from the Tracking server are explained in brief VEHICLE ACTIVITY REPORT This function returns the user with an Activity
29. ser s Manual EIE 4 o A EXE CT Lite User s Manual Further explanation of the LED functionality is described below RED LED Power Indicator Power indicator When the unit is powered on using main power the led will be permanently on When the main power is cut the unit will switch to backup battery mode the led will flash until the backup battery runs out of power Troubleshooting Check that you have a valid 12V or 24V source connected to the device The Red wire should be connected to the positive terminal and the Black wire should be connected to the Ground terminal If there is power applied to these wires please check the inline fuse YELLOW LED GSM GPRS Indicator GSM GPRS indicator The yellow led will flash when the device is connected to the tracking server with a valid GPRS connection It will stay on continually when it is in sms mode only or when the GSM is present but invalid APN username and password have been set Troubleshooting If the yellow light is not on at all please ensure the GSM antenna is connected and that the sim card is properly inserted with the gold terminals facing the circuit board Please ensure the terminals are clean and the sim card clips into place appropriately If this fails please put the sim card into a phone and make sure that it is registered and that you are able to send a message from the phone Please ensure the sim pin on the sim card has
Download Pdf Manuals
Related Search