iZone 110 User Manual A5 - Crispair Air Conditioning
Contents
1. on the side of the C110MC box Active As an example the diagram shows 4 active zones C110WC C110WC 3 3 Testing and Labelling Switch all zones OFF and one zone ON Check which zone is being supplied with air Label the zone accordingly 4 0 User manual Press the silicone button to switch zones on and off The LED will illuminate when the zone is on 5 0 Further assistance 1 If you require warranty or repair on your air conditioning system or iZone system you should contact your installation company 2 Ifyou want to add more zones you should contact your installation company 3 If your require assistance operating your iZone contact Airstream Components www air stream com au info air stream com au Phone 08 6254 2408 izOne airstream 102. izone 110 Zone Controller Installation and User Manual Table of contents Section Description Page No 1 0 Installation 3 1 1 Standard wiring layout 1 2 Installation instructions ince cence cece eee ence eee eee eee eee oaao E 20 System initialisation se sce ee teen Sa so oo ooo oaoa oe suaa AA System connguraton no oni ge ee ine cnet apse meee a asec a a ee 3 1 Set the number of zones required 6 7 3 2 Set the number of electronic constants required 6 7 3 3 Testing and Labelling 6 7 4 0 User manual 8 5 0 Further assistance 10 1 1 Standard wiring layout CZDA Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 C110WC 6 Zone system with 2 wall controllers shown A maximum of 6 zones and 2 wall controllers can be supported by one iZone 110 j system C110WC 1 2 Installation instructions The C110MC can be installed on top of the indoor fan coil unit Do not run the blue network cables alongside 240 Volt wiring When installing network cables down wall cavities or chasing network cables into walls tape up and protect the RJ45 connector to avoid damage to the connectors Always install zones in consecutive ports starting at Zone 1 The back of the C110MC is marked with the zone port numbers Do not directly hardwire the CT24AC into the AC unit s power supply This may void the warranty as it will require an electrician in the event that repair of the iZone 110 system is required Con
3. ined number of zones remain open at all times even if all the zones are switched off If 1 electronic constant is selected Zone 1 will automatically open if all the zones are closed If 2 electronic constants is selected Zone 1 and 2 will automatically open if all the zones are closed Only set the number of electronic constants to 0 if the system is an old fashioned design with at least one supply air outlet that is not zoned Set the AC unit fan speed to high and close all zones Open one zone at a time and check which room the air is being supplied to Label the zone using the stickers provided being care full to place the sticker squarely in the recess provided Peel off the protective coating from the sticker 3 1 amp 3 2 Set up number of zones amp electronic constants required N29007 7 zen z X id A 1 ti lt a o C110MC Installation Instructions Set number of electronic constant zones required on switch on the side of the 1 Connect Zone Damper Actuators CZDA to the Zone ports C110MC box using the RJ11 cables Electronic 2 Connect the Wall Controllers C110WC to the ports using Constant Zones the Blue RU45 cables required As an example the switch is shown 3 Select the number of active zones required on the dip switch selecting 1 electronic constant 4 Select the number of electronic constant zones required 5 Connect the power supply to the CT24AC port Set number of zones on the dipswitch
4. nect Zone Damper Actuators CZDA to the zone ports using the RJ11 cables as shown Connect the Wall controller s C110WC to the C110WC ports using the RJ45 cables Only connect the power supply to the CT24AC port after all components have been connected 2 0 System initialisation All new or modified systems must be initialised prior to system configuration To initialise the system press the button on the underside of any wall controller This button is recessed so you will need to use a pen to press the button The time to initialise the system will vary depending on the number of motors connected The system will also initialise wnen power is restored after a power failure Using a pen press the button on the underside of the screen 3 0 System configuration WARNING Only qualified iZone 110 installers should configure the iZone 110 System Incorrect configuration could result in damage to your air conditioning unit and system 3 1 3 2 3 3 On the C110MC set the number of active zones required on the 6 position dip switch By moving the associated dipswitch up the respective zone will be deactivated and conversely by setting the dipswitch down ON the associated zone will be activated The factory setting is all 6 zones activated On the C110MC set the number of electronic constants you require to ensure the safe operation of the system An electronic constant is a safety feature and ensures that a predeterm
Download Pdf Manuals
Related Search