USER MANUAL - Redgumbrand.com.au
Contents
1. please contact your __ Indicator authorized dealer for adjustment To smoothly shift the derailleur the steps below should be followed 1 Stop pedaling before shifting the gears while riding 2 Only shift one gear one time while switching the gear change handle Revo shift lever shown as above 3 Resume pedaling Note If you shift the gears while pedaling a clash may be heard due to gears shifting over dynamic moving parts Operating Instructions of Go Button and Throttle Handle Kit Optional The power assist of your E Bike will remain on continuously when the Go Button is held on or the Throttle Handle is twisted Note Do not use Go Button or Throttle Handle without pedaling especially when travelling up a slope The use of the Go Button or Throttle Handle will reduce the battery range during your ride Regular Check for Safety before Riding 1 Check the Tire Pressure before riding The tire pressure on front and rear tires is to be maintained at 50PSI Check if the tire tread is worn excessivly If so the tire needs to be replaced Check Power Assist The power assist should cut off when one of handbrakes is engaged or the pedaling has being stopped for over 3 seconds Check Battery Check the battery pack fits into the battery mount firmly and the LED Light of the battery pack lights up when the main switch is switched on at the II position Check the battery is fully cha2. at once after selecting your desired stage 4 Turn off the battery then on to complete adjustment Note It s recommended you use the 1 or lower stages to save battery charge if you are riding on level ground frequently The 10 stage is the default setting on your new E Bike Adjustment of the Saddle 1 L the cl 2 Adjust the seat post to _ the desired height position 4 Ensure the saddle is aligned on your E Bike and then tighten the clamp lever when your saddle has been correctly positioned 3 Be aware of the maximum height markings MIN INSERTION as shown on the tube of the saddle Cushion Adjustment for the Saddle 2 Use the Hex Wrench to loosen or depress the cushion to adjust to your personal comfort 1 Loosen the clamp lever and withdraw the saddle connected with seat post Operating Instructions of Derailleur Shimano Inter 3 Shift Gear Your E Bike is equipped with the Shimano Inter 3 3 speed shift gear at the rear wheel axle It is easy to change the gear ratio by shifting the gear change handle while riding Handle position Riding Gradient Speed Gear Ratio 2 Lee road with a slight slope Middle Low To save your energy while At a moderate gradient mounting a slope Pedaling becomes heavier Indicator moves 1 gt 2 3 Revo shift lever A Ss Pedaling becomes lighter Indicator moves 3 2 1 If the gear changes cannot be performed smoothly
3. can be removed without depressing the key this means that the battery pack has not been properly locked Repeat the above procedures again 11 Dismounting the Battery Pack 10Ah 13 5Ah gt Switch the battery pack off Unlock the battery pack by using your battery key switched to be level Depress the key to release the lock and use the other hand to push the battery pack sliding out from the battery slide Mounting the Battery Pack 10Ah 13 5Ah i 7 of os a A PD 4 i Ki Slide the battery pack onto the The battery pack will be securely rail and all the way down locked and can t be removed to lock the battery pack with when the key is switched toward the other hand as shown the vertical position as shown 12 oteps to Charge the Battery 1 Turn off the main switch of battery pack Charger Battery Pack 2 Dismount the battery pack and then place it at a ventilated place to be charging 3 Swivel the charging port cover of battery Charging pack and then connect the charger plug Indicator LED gt of the charger 4 Plug the power plug of the charger into secure power source to start charging battery Note Ensure that the charger plug is dry and securely connected to the charger port of battery pack Operating Instruction 1 Ensure the input voltage is between 100V 240V 2 Ensure the battery to be charged is a C LiFePO C Coated Lithium Iron Phosphate Based
4. dealer for a detailed check if there is concern or issue with your charger or batteries Caution 1 All charging will be completed within 7hrs dependant on different on the size of battery pack and charger Do not charge the batteries for longer than 24 hours Do not expose the charger to the rain water or a humid place Do not use the battery charger near flammable articles or in unventilated places The battery pack is not allowed to be disassembled and should not be exposed to water or fire For your safety do not short circuit the output plug or it may cause unexpected danger or damage Use the specified charger only for C LiFePO C Coated Lithium Iron Phosphate Based Battery Pack 24V supplied by PMMC 6 Always use the battery charger and power cord supplied by PMMC 7 Before plugging in the power cord of the charger please confirm that the local power supply corresponds with the requirement of the charger The manufacturer will not be responsible for any damage or injury due to improper or unsafe use of the battery charger 14 Battery Pack Feature e Main Switch Function How to operate LED Lights Function SAh 6Ah 10Ah 13 5Ah EE Controller Controller amp Battery Pack Activate U Controller amp Battery Pack o Power O sw e The LED Light on controller and battery pack utilizes the 1W Warm White LED Light which is a green energy and provides moderate light in the dark e
5. Battery Pack supplied by PMMC 3 Make sure the power cord battery cable and battery terminals are in good condition 4 Make sure the connecting battery rating is the same as the charger output voltage 24V 5 While charging the charging indicator LED will display RED When the light turns GREEN the battery is fully charged Charger LED Indication 1 LED GREEN Power On when not connected to the batteries 2 LED RED Charging 3 LED GREEN Fully Charged when connected to the batteries Trouble Shooting 1 If the LED light is OFF all the time while charging Check if the power connections are in good condition If the LED light is still off all the time while charging the battery charger may have malfunctioned Please consult your authorized dealer for further assistance 2 Ifthe LED light does not switch from GREEN to RED when the charging process begins 13 Check if the connection between charger plug and charging port of the battery is correctly inserted Check if the battery pack is already fully charged Check if the battery is functioning properly and consult your local authorized dealer for assistance The charging time continues for a long duration Irregular Check if the battery is faulty or aged and consult your local authorized dealer for assistance The battery overheats Check your battery and charger if connected properly Stop charging immediately and consult your authorized
6. Pack 5Ah 6Ah 4 Go Button Kit 2 ON 1 OFF ON Il Switch Main Switch 5 Gear Shift Handle x 6 Throttle Handle Kit x x Optional SAh 6Ah C LiFePO 10Ah 13 5Ah C LiFePO Battery Pack Battery Pack 4 9 s yY Features 1 Saddle 6 Foot Stand 11 Frame f6 Rear Carrier Light 7 Actuator amp l 17 10Ah 13 5Ah C LiFePO 8 Wheel Rim 13 Basket 18 Carrier for 10Ah C LiIFePOQ Battery Pack x 9 Spoke 14 Top Tube x Optional or Equipped with the model as ordered Safety Warnings Do not operate your E Bike before reading this user manual thoroughly Do not disassemble the battery pack and modify the unit or your warranty will be void and you will be responsible for the modification 3 The maximum load for the carry basket is 2kgs 10 11 12 13 14 15 Check the tire pressure of front and rear wheels Pressure to be around 5OPSI before riding Make sure that the battery pack has been fully charged before first use and remove the charger after fully charging Turn the main battery switch off while charging or not using Check that all electrical connections and mechanical parts are securely locked and fastened before using your E Bike Your E Bike is not recommended for competition stunt any aggressive or off road riding Refer to your warranty terms and conditions The performance and mileage of the unit will be varied with the battery condition t
7. The positions of LED light on battery pack and controller are referred to the photos as below of controller starts on amp Il if existed LED Light of Battery Pack 5Ah 6Ah starts on II e The portable battery pack 5Ah 6Ah can be stored in a carrying bag supplied with each E Bike and can be used for individual lighting system the same as a flashlight device Dependant on the charge of the battery the warm white LED light can last for 3 6 days e The threaded hole available underneath the 5Ah 6Ah battery pack is a connection interface to other devices for illumination such as the camera stand as shown Battery Pack 5Ah 6Ah Carrying Bag for Battery Pack 5Ah 6Ah mounted on a camera stand 15 Battery Capacity LED Light Indicator Percent Left of LEDs Illuminated Battery Remaining Charge Battery Capacity Battery pack has adequate power pack Battery pack has adequate power adequate power Please note that the percent left of battery capacity and battery remaining charge shown above are listed for reference Warning For your safety do not check the LEDs of battery remaining charge while in motion it may affect your attention to the road condition Always check the LEDs of battery remaining charge only when stopped and in a safe place 16 Riding Range per Different Capacity of a Fully Charged Battery Pack Type Environtriendly C LiFePO gt 5Ah 6Ah 10Ah 13 5Ah Battery Capac
8. ave energy 7 P a lace lean for both you and the battery A dry or dirty chain and under inflated tires can cause the Poor maintenance motor to use more energy 17 Maintenance Periodic Maintenance Please contact your authorized dealer to maintain your E Bike periodically e Make sure the front and rear wheel in good condition e Maintain the battery pack and charger in good condition e Maintain the motor and controller in good condition e Check and maintain the brake system to keep it in good condition e Use lubricant to maintain metal parts of the unit however do not lubricate the brake shoes e Check all electrical connections and mechanical parts are securely locked and fastened Routine Maintenance e Check the tire tread and tire pressure are in good condition e Check the battery capacity remaining charge and charger in good condition e Clean up the surface of your unit without spraying over all electrical connections 18 Trouble Shooting PROBLEM POSSIBLE CAUSE SOLUTION Battery pack is loose Battery pack has not been Loosening issue such _ totally locked onto the as battery pack could be battery holder removed when the key on battery pack is not depressed Battery gauge LED has Battery pack charge is low no display when power or battery not connected on Power assist fails to Controller may go to sleep perform its intended mode to preserve battery function when pedaling cha
9. em is still exists 19 APT Power Assist Electric Bicycle DISCLAIMER Congratulations on your purchase of SUNRUNNER APT Power Assist Electric Bicycle This APT Power Assist Electric Bicycle is not intended to be used by individuals with physical limitations that could prevent the user from operating the APT Power Assist Electric Bicycle safely PMMC disclaims all responsibility for any personal injury or property damage which may occur as a result of improper or unsafe use of its products Mechanical or electrical defects will be dealt with on a contingency liability basis Warranty is only valid when genuine SUNRUNNER parts are used All modifications on the APT Power Assist Electric Bicycle unless approved and authorized by SUNRUNNER will automatically invalidate the warranties Standard warranty does not extend to consumable items and parties other than the original purchaser The preceding guidelines are intended to assist you in the safe operation of this APT Power Assist Electric Bicycle Should you have any questions about the correct operation of the APT Power Assist Electric Bicycle please contact your authorized dealers Model Name SUNRUNNER Serial No Provider s Stamp PIHSIANG MACHINERY MFG CO LTD www pihsiang com tw sales pihsiang com tw 20 P N 300905 28
10. emperature terrain wind speed tire pressure rider weight and the maintenance Your E Bike is able to sense your feet s force on the pedal to provide you the assist power once you ride it Before depressing pedal on your E Bike please ensure the road ahead is clear of obsticles and traffic Adjust the height of the saddle to fit your body size Take heed of the maximum height markings on the post of the saddle Your authorized dealer will give you assistance if requested Refer to the instruction sheet for the SHIMANO Inter 3 Gear to switch 3 stages of gears for a more comfortable riding at different slopes Always consult your doctor for advice on your physical condition and follow traffic rules while riding Ensure you wear safe footwear and keep loose articles of clothing clear of moving parts on your E Bike while riding Always handle the battery pack with care and do not drop it Do not connect the terminals of battery pack with any foreign object User Guidance 10 Stages Power Assist Output Adjustment 1 Turn off the power and depress the pedal while the bike is faced against the wall 2 Press the main switch to either left 1 or right I1 position while depressing the pedal continuously 3 After 10 seconds the light of controller will flash as below The 1 flash means the 1 stage The 2 flash means the 2 stage The 10 flash means the max the 10 stage output from the controller Release the pedal
11. ity Configuration or Option 5Ah 1 8kg 6Ah 1 9kg 10Ah 3 4kg 13 5Ah 3 9k Capacity Weight 9 9 l 9 en Reference Range Remark 2A Standard for 5 Ah 6 Ah 10 Ah 13 5Ah for C LiFePO Capacity 4A Option for 10 Ah 13 5Ah Batteries Charging Time Approx 2 5 7hrs depending on the charger capacity Remark Your riding range will vary with your weight battery condition temperature terrain wind speed tire pressure and the maintenance etc As the last battery indicator light starts flashing you may continue to ride the E Bike for approx 2 KMs further The maximum weight capacity of the E Bike is around 100 Kgs Specified Charger Charger Conditions that Effect Your Riding Range Item Effects Extreme cold and heat can consume the battery s charge 1 Ambient temperature more quickly Riding into a strong headwind will cause the motor to use more energy 3 Roa senaniane Hilly and rough terrain will cause the motor to use more energy A Nester Carrying extra luggage on the carrier or in a basket will cause the motor to use more energy Since more energy is used during initial acceleration riding in 5 Acceleration from a E aaa traffic conditions i e city that force you to start and stop trae often will cause the motor to use more energy A heavier rider will cause the motor to use more energy than Rider weight with a lighter rider Pedaling in a proper gear for the terrain will help s
12. rge after being idle for few minutes Or if one of handbrakes fails to restore to its disengaged position Power assist function Battery pack with an empty discontinued when charge riding Poor traveling range Frequent riding on gradients poor tire pressure battery pack with insufficient charge or battery aging etc Follow the instruction to dismount then remount battery pack again to check if battery pack can not be removed without depressing the key Check if battery pack has been fully charged before use Refer above if the battery pack has a loosening issue Switch power off and then back on to remove from sleep mode Check handbrakes are totally disengaged when the levers have been released As the last battery indicator light start flashing then the battery pack must be recharged as soon as possible or the power assist will be discontinued after approximately 2 KM of further riding Decrease chance to ride on gradients to check if a longer range is acquired fill up tire pressure to 50 PSI fully charge the battery daily after use or replace a new battery pack etc Unusual motor gear Check if any foreign object Clean up obstacles around the sound noise obstructs wheels or motor wheels and motor Note You must use the genuine SUNRUNNER charger dedicated for C LiFePO Battery Pack to be charged Please contact your authorized dealer if the above solution has been checked and the probl
13. rged before use Check Motor and Control System Check the motor and control system ensuring normal operation General Inspection Check if brake shoes are worn and need to be replaced Check if the braking function is operating correctly Check if the front and rear wheels are operating smoothly Check if all connectors on E Bike are firmly secured without any damage lf you have any questions after checking please refer to Page 17 and 18 for trouble shooting or contact your authorized dealer for inspection and maintenance Riding Safet Always follow local traffic rules while riding Check the battery gauge if the charge is sufficient to keep the power assist for your planned riding The maximum loading capacity of the carrier amp front basket is 12 kgs amp 2 kgs respectively Do not overload the carrier or basket Do not keep riding your E Bike if a problem has occurred Refer to the solutions for trouble shooting page 19 or contact your authorised dealer for further inspection and maintenance Ensure to use the spare parts supplied by PMMC for replacement __F Bike care The lifetime of your E Bike will be adversely affected by exposures to aggressive road conditions such as dirt rain water or salt spray etc Ensure your E Bike including the battery pack are used as instructed in this manual and are protected for transportation Always store your E Bike indoors when not in use This will prolong the life
14. span of your E Bike Battery amp Charging Usage of Light and Charging The main light above as integrated in the controller box will always remain on when the main switch is on Both battery light and main light will be Charge the battery at once on if the main switch is switched when the last light LED starts onto the right side marked with II and flashing main light will only be on if the main switch is switched onto the left side marked with I Battery can be fully charged within 2 to 6 hours depending on the different capacity of charger which must be a specified charger approved by PMMC Swing the charging port cover away to disclose the charging port for charging 10 Dismounting the Battery Pack 5Ah 6Ah Note Make sure the battery pack handle is latched as shown before sliding out the battery Depress the key to release the Hold the battery pack lock and use the other hand to handle and remove it push the battery pack and slide it out from the battery mount Mounting the Battery Pack 5Ah 6Ah VAA A I p YE Y q VA y VMATY TS Y aY 4 ry Please secure the battery pack mount The battery pack will be with one hand and slide the battery securely locked and can t be pack onto the rail of mount all the way down to removed when the key lock the battery pack with the other hand as is switched toward the vertical shown position as shown Note If the battery pack
15. t Electric Bicycle is USER MANUAL Power Ass APT Table of Contents INMPFOGUCUOM spxcacisucecensatctctacmnetnepvectneahduerea ends sicenimeeesucedes 3 FEATS nacscn sce enters enhcenemmundinusbiduatiet ARAE E 3 Safety Warnings ccccccsssceusseccuuucceueeeeusessuuucceusneeurnssaas 5 USKE e EE E E E AT 6 Battery and Charging cccce cece eee eeee eee teeeeeeeenaeeeeeeeees 10 WIIG MONG Cs ctsane tt naargaenah E SE 18 TROUD Ie NOO O e A E AE 19 DISCIAIME T ersen e ORE 20 Introduction Thank you for purchasing the SUNRUNNER APT Power Assist Electric Bicycle hereinafter referred to as E Bike designed and manufactured by PIHSIANG MACHINERY MFG CO LTD hereinafter referred to as PMMC The user s manual contains important information concerning the operation and the safe use of your E Bike Please read this manual carefully and thoroughly before riding your E Bike and make sure that you fully understand the operation of the E Bike as instructed in this manual If you have any queries about the spare parts for the maintenance or any other concerns of your E Bike please contact your authorized dealer for assistance X SUNRUNNER is a registered trademark of the PMMC products X APT is registered for Advanced Power Technologies developed and owned by PMMC x PMMC reserves the right to change the wording and specification without prior notice Features 1 C LiFePO Battery
Download Pdf Manuals
Related Search