Home

Leica DIGICAT 500i/550i User Manual

1. Instrument dimensions i Pond 13 mm 0 512 Inches 13 490 mm 19 3 Inches 210 mm 8 3 nches p 440 mm 17 3 Inches Weight Instrument 7 3 kg 16 1 Ibs DIGICAT 500i 550i Technical Data 77 DIGICAT 500i 550i Technical Data Environmental specifi cations Conformity to national regulations 78 Type Description Temperature Operating 20 C to 50 C 4 F to 122 F Storage 40 C to 70 C 40 F to 158 F Protection against Frame IP54 IEC 60529 Water Dust and Dust protected Sand Rod Fully submersible Humidity 95 RH non condensing The effects of condensation are to be effectively counteracted by periodically drying out the product e FCC Part 15 applicable in US e Hereby Leica Geosystems AG declares that the Conductive Rod is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at http www leica geosystems com ce placed on the market and be put into service without restrictions in any EEA C Class 1 equipment according European Directive 1999 5 EC R amp TTE can be member state The conformity for countries with other national regulations not covered by the FCC part 15 or European directive 1999 5 EC has to be approved prior to use and opera tion 10 4 Sonde Technical Data Operating transmiss
2. DIGICAT 500i 550i Safety Directions 69 DIGICAT 500i 550i Technical Data 10 10 1 Typical detection range Operating depth range Typical depth accuracy Operating frequencies Technical Data Locator i Series Technical Data 70 Mode Distance along conductor Power mode length of conductor Radio mode length of conductor Conductive Rod mode length of unwound rod Mode Range Power mode to3m 10 ft Radio mode to2m 7 ft Transmitter mode to3m 10 ft DIGICAT 500i DIGICAT 550i N A 1096 of depth in line or Sonde N A 0 3 to 3 0 m 1 to 10 ft depth range Mode Frequency Power mode 50 Hz or 60 Hz Radio mode 15 kHz to 60 kHz 8 kHz mode 8 192 8 kHz Mode Frequency 33 kHz mode 32 768 33 kHz Auto mode Power mode and Radio mode Display panel 48 segment bar graph 5 mode indicators Battery status indicator Line depth indicator Sonde depth indicator Bluetooth indicator Integrated backlight Annual service indicator e 3 alpha numeric dot matrix displays 5x7 Keypad 2 membrane push buttons Speakers Dual speakers Audio volumes 85 dBA 30 cm Tone e Pneumatic headpho Power Radio and Auto mode continuous tone different pitch for each tone 8 kHz and 33 kHz mode pulsed tone different pitch for each tone All five tones are di
3. Leica DIGICAT 5001 550i User Manual rud i 1 Ww BE ul T F e V 1 0 when it has to be right Seica Geosystems wg n 3 Leica DIGICAT 5001 550i oy User Manual a a P d om om ph Sle gm Ac E T w e e Version 1 0 English when it has to be right Leica Geosystems DIGICAT 500i 550i Introduction 2 Introduction Purchase Congratulations on your purchase of a DIGICAT instrument p This manual contains important safety directions as well as instructions for setting up the d product and operating it Refer to 9 Safety Directions for further information Read carefully through the User Manual before you switch on the product Product identification The model and the serial number of your product are indicated on the type plate Enter the model and serial number in your manual and always refer to this information when you need to contact your agency or Leica Geosystems authorised service workshop Type Serial No Symbols The symbols used in this manual have the following meanings Type Description AN Danger Indicates an imminently hazardous situation which if not avoided will result in death or serious injury A Warning Indicates a potentially hazardous situation or an unintended use which if not avoided could result in death or serious injury A Caution Indicates a potentially hazardous situation or an unintended use
4. This signal is radiated from the centre of the service This is even more important when the signal is produced by a Sonde lying in a large diameter conduit Precautions Always compensate depth reading for service size DIGICAT 500i 550i How to Use the Locator 23 DIGICAT 500i 550i How to Use the Locator Measuring Sonde depth 550i only Ee Activating line depth will provide an inaccurate readout C 24 Switch on the sonde and set to the required frequency Refer to 7 How to Use the Sonde for more information Select either 33 kHz or 8 kHz mode to suit the Sonde s output Position the Locator directly over and in line with the Sonde Refer to 7 How to Use the Sonde for more informa tion Press and hold down the i Button for 2 seconds until the dashed lines have scrolled through once The display readout will indi cate the depth of the Sonde and the Sonde mode icon will be displayed Always use chalk or paint to mark services never pegs or other material which are driven into the ground Additional services may be within the excavation zone as well as the service you are taking a depth reading from A Warning Depth code informa tion DIGICAT 500i 550i How to Use the Locator Depth shown and diameter Take special care w
5. Watch out for erroneous measurement results if the product has been dropped or has been misused modified stored for long periods or transported Precautions Periodically carry out test measurements and perform tests indicated in the user manual particularly after the product has been subjected to abnormal use and before and after important measurements A Danger A Warning A Caution A Warning Because of the risk of electrocution it is very dangerous to use the product in the vicinity of electrical installations such as power cables or electrical railways Precautions Keep at a safe distance from electrical installations If it is essential to work in this environ ment first contact the safety authorities responsible for the electrical installations and follow their instructions During dynamic applications for example stakeout procedures there is a danger of accidents occurring if the user does not pay attention to the environmental conditions around for example obstacles excavations or traffic Precautions The person responsible for the product must make all users fully aware of the existing dangers The absence of a positive indication does not guarantee the non existence of a service Services without a detectable signal may be present The Locators can only locate non metallic services such as plastic pipes typically used by the water and gas utilities with the use of appropriate accessories Precauti
6. short circuited battery terminals can overheat and cause injury or fire for example by storing or transporting in pockets Precautions Make sure that the battery terminals do not come into contact with metallic objects Only Leica Geosystems authorised service workshops are entitled to repair these products Electromagnetic Compatibility EMC The term Electromagnetic Compatibility is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present and without causing electromagnetic disturbances to other equip ment A Warning A Caution A Caution A Warning Electromagnetic radiation can cause disturbances in other equipment Although the product meets the strict regulations and standards which are in force in this respect Leica Geosystems cannot completely exclude the possibility that other equipment may be disturbed There is a risk that disturbances may be caused in other equipment if the product is used in conjunction with accessories from other manufacturers for example field computers personal computers two way radios non standard cables or external batteries Precautions Use only the equipment and accessories recommended by Leica Geosystems When combined with the product they meet the strict requirements stipulated by the guidelines and standards When using computers and two way radios pay attention to the
7. 550i How to Use the Property Connection Set 46 6 6 1 Description 6 2 Property Connection Set main parts How to Use the Property Connection Set General Information The Property Connection Set provides a safe technique of applying a traceable signal to live electricity cables It is connected to the service via a mains plug outlet and provides a trace able signal Supply is not interrupted by the applied signal and the risk of serious injury is greatly reduced Property Connection Set Overview a Mains plug connector C b In line isolator c Transmitter plug connector 6 3 How to Locate a Service Using the Property Connection Set Using the Property Connection Set Connect the Property Connection Set to the Transmitter 2 Connect the Property Connection Set to a live mains outlet Ensure the switch on the mains is on 3 Switch the Transmitter on and select 33 kHz A good signal output is indicated when the audible output from the Transmitter is constant 4 Trace the length of the service using the Locator set to the same frequency m S e The mains supply must be live and switched on for correct operation e Works best with 33 kHz DIGICAT 500i 550i How to Use the Property Connection Set 47 DIGICAT 500i 550i How to Use the Property Connection Set 48 A Danger A Danger A hazardous signal may be present on the connection plug of the Property Connection Set when connected
8. Clamp provides a safe technique of applying a signal to services such as telecom cables etc It is connected to the Transmitter and then clipped around the service Supply is not interrupted by the applied signal 5 2 Signal Clamp Overview Signal Clamp main parts b c 9 Transmitter plug connector d b Jaws a c Handle d Cable 5 3 How to Locate a Service Using the Signal Clamp Using the Signal Clamp 1 Connect the Signal Clamp to the Transmitter 2 Open the jaws of the Signal Clamp and place around the service to be traced 3 Switch the Transmitter on and select 33 kHz A good signal output is indicated when the audible output from the Transmitter is constant 4 Trace the length of the service using the Locator set to the same frequency eS Ensure the clamp jaws are fully engaged e Works best in 33 kHz mode A Danger A hazardous signal may be present on the connection plug of the Signal Clamp when clipped over a live service Precautions The clamp should be connected to the Transmitter before clamping around a live service DIGICAT 500i 550i How to Use the Signal Clamp 43 DIGICAT 500i 550i How to Use the Signal Clamp A Danger A hazardous signal may be present on the service causing personal harm Precautions use 44 Do not use on electrical services which have impaired or no insulation If in doubt do not DIGICAT 500i 550i How to Use the Signal Clamp 45 DIGICAT 500i
9. European directive 1999 5 EC has to be approved prior to use and opera tion 10 5 Property Connection Set Technical Data Operating transmission 8 192 8 kHz or frequencies 32 768 33 kHz Instrument dimensions 80 mm 3 1 Inches CORE 100 mm 3 9 Inches Weight Instrument 0 15 kg 0 3 Ibs tar a specifi Type Description cations Temperature Operating 20 C to 50 C 4 F to 122 F Storage 40 C to 70 C 40 F to 158 F Protection against Water Dust IP54 IEC 60529 and Sand Dust protected DIGICAT 500i 550i Technical Data 81 DIGICAT 500i 550i Technical Data 82 Type Description Humidity 9596 RH non condensing The effects of condensation are to be effectively counteracted by periodically drying out the product Conformity to national e FCC Part 15 applicable in US regulations e Hereby Leica Geosystems AG declares that the Property Connection Set is in compli ance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at http www leica geosystems com ce Class 1 equipment according European Directive 1999 5 EC R amp TTE can be placed on the market and be put into service without restrictions in any EEA member state The conformity for countries with other national regulations not covered by the FCC part 15 or European directive 1999 5 EC has to be app
10. Hz 230 V 50 Hz 240 V 50 Hz 220 V 50 Hz 240 V 50 Hz 220 240 V 50 Hz 120 V 60 Hz 115 220 V 50 Hz 230 V 50 Hz 220 V 50 Hz 220 V 50 Hz 230 V 50 Hz 127 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz Niger Nigeria Rwanda Senegal Sierra Leone Somalia South Africa Sudan Swaziland Tanzania Togo Tunisia Uganda Zaire Zambia Zimbabwe 104 220 V 50 Hz 230 V 50 Hz 220 V 50 Hz 110 V 50 Hz 230 V 50 Hz 220 V 50 Hz 220 240 V 50 Hz 240 V 50 Hz 220 V 50 Hz 230 V 50 Hz 127 220 V 50 Hz 127 220 V 50 Hz 240 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz Asia Abu Dhabi Afghanistan Armenia Azerbaijan Bahrain Bangladesh Brunei Cambodia China Cyprus Georgia Hong Kong India Indonesia Iran Iraq Israel Japan Jordan Kazakhstan Kirgizstan Korea North Korea South Kuwait Laos Lebanon Malaysia Myanmar 230V 50Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 110 230 V 50 Hz 60 Hz 230 V 50 Hz 240 V 50 Hz 220 V 50 Hz 220 V 50 Hz 240 V 50 Hz 220 V 50 Hz 220 V 50 Hz 230 250 V 50 Hz 60 Hz 127 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 230 V 50 Hz 100 220 V 50 Hz 60 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 110 220 V 60 Hz 240 V 50 Hz 220 V 50 Hz 110 220 V 50 Hz 240 V 50 Hz 240 V 50 Hz DIGICAT 500i 550i World Frequency Zones Oman Pakistan Philippines Qatar Saudi Arabia Singapore Sri Lanka
11. Water Dust and Dust protected Sand With cover closed IP67 IEC 60529 and secured Dust tight Waterproof to 1 m temporary immersion Humidity 9596 RH non condensing The effects of condensation are to be effectively counteracted by periodically drying out the product DIGICAT 500i 550i Technical Data 75 DIGICAT 500i 550i Technical Data 76 Conformity to national e FCC Part 15 applicable in US regulations e Hereby Leica Geosystems AG declares that the DIGITEX is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at http www leica geosystems com ce Class 1 equipment according European Directive 1999 5 EC R amp TTE can be placed on the market and be put into service without restrictions in any EEA member state The conformity for countries with other national regulations not covered by the FCC part 15 or European directive 1999 5 EC has to be approved prior to use and opera tion Frequency band 8 kHz and 33 kHz Output power 100 mW maximum when directly connected to a buried service with a ground impedance of 100 Ohm or less 10 3 Conductive Rod Technical Data Typical detection range Both modes Line and Sonde Typical 3 0 m 10 ft Tracing distance 30 m 99 ft 50 m 165 ft 80 m 263 ft maximum Reel length dependant Operating transmission 8 192 8 kHz or frequencies 32 768 33 kHz
12. a completely safe condition The manufacturers of non Leica Geosystems accessories for the product are responsible for developing implementing and communicating safety concepts for their products and are also responsible for the effectiveness of those safety concepts in combination with the Leica Geosystems product DIGICAT 500i 550i Safety Directions 59 DIGICAT 500i 550i Safety Directions 60 Person in charge of the product A Warning 9 5 A Warning A Caution The person in charge of the product has the following duties Tounderstand the safety instructions on the product and the instructions in the user manual To be familiar with local regulations relating to safety and accident prevention To inform Leica Geosystems immediately if the product and the application becomes unsafe The person responsible for the product must ensure that it is used in accordance with the instructions This person is also accountable for the training and the deployment of personnel who use the product and for the safety of the equipment in use Hazards of Use The absence of instruction or the inadequate imparting of instruction can lead to incorrect or adverse use and can give rise to accidents with far reaching human material financial and environmental consequences Precautions All users must follow the safety directions given by the manufacturer and the directions of the person responsible for the product
13. a quality system which meets LL O Wi the International Standards of Quality Management and Quality Systems ISO standard 9001 and Environmental Management Systems ISO standard 14001 Original text 2010 Leica Geosystems AG Heerbrugg Switzerland 780598 1 0 1en Ask your local Leica Geosystems dealer for more information about our TQM program Leica Geosystems AG Heinrich Wild Strasse e CH 9435 Heerbrugg Switzerland euca Phone 41 71 727 31 31 when it has to be right www leica geosystems com Geosystems
14. enable a user to verify the performance of the Sonde To carry out this test the following are required e A Locator to detect the signal Awork area free of services as illustrated 1 Inspection e Casing The casing should be free of significant damage with the sealing ring and the screw thread intact Once the general condition of the Sonde is established the self test can then be used to indicate the basic unit function and state of the batteries 2 LED test Turn on the sonde the led display will illuminate 3 Battery check A dull LED and lack of detection range will indicate poor battery condition Use alkaline batteries 1 Switch sonde on and activate 33kHz mode 2 Set Locator to 33 kHz mode and aim at Sonde see diagram 3 At 2 m 6 56 ft the Locator must be at maximum 4 Repeat this with Sonde and Locator in 8 kHz DIGICAT 500i 550i Functional Checks 99 DIGICAT 500i 550i Functional Checks 100 5 m 16 4 ft cS If any of these tests give no response or a significantly different response from normal the Sonde should be returned for service Functional test check Functional Test Check List list Unit Serial Number Comments Sonde Test Operative Fail analysis Notes Yes No N A 1 Casing Fail Casing should be free of damage 2 Screw thread and Fail Screw thread must be intact seal and seal in place 3 Battery contacts Fail Contacts
15. main parts a Accessory Cover b Battery Cover c Power Control Switches the unit on or off d Mute Control Used to silence the Transmitter e Mode Display Indicates which mode is selected Induction or Connection f Frequency Control Button Used to select 8 kHz or 33 kHz output i ZZ g Frequency Display Za Indicates which frequency is selected 8 kHz or Ne zz PON 33 kHz E N goes h Output Level Control YAN r Used to vary the signal output of the Transmitter J nee i Battery Indicator Flashes when the batteries need to be replaced Replace all batteries when indicated j Level Meter Display a b c defghij k Indicates the signal output level and the condition of the batteries on initial start up k Connection Socket Used to connect accessories directly to metallic services Standard crocodile clip cable set Changing the battery The battery indicator flashes when approximately 2096 of battery life remains The rate of flashing increases as the battery life declines 1 Loosen the two screws of the battery cover and remove them together with the cover 2 Replace all batteries with four new LR14 C batteries CE Alkaline batteries should be used DIGICAT 500i 550i How to Use the Transmitter 33 DIGICAT 500i 550i How to Use the Transmitter 34 3 3 Start up test How to Locate a Service Using the Transmitter The following test sequence will take place every time the T
16. must be free of corro sion 4 33 kHz mode Fail LED must be illuminated brightly and pulse fast Locator must provide maximum display at 2 metres 5 8 kHz mode Fail LED must be illuminated brightly and pulse slowly Locator must provide maximum display at 2 metres Tested by Date DIGICAT 500i 550i Functional Checks 101 DIGICAT 500i 550i World Frequency Zones Appendix B North America Canada United States Mexico Central America Bahamas Barbados Belize Bermuda Costa Rica Cuba Dominican Republic El Salvador Guatemala Haiti Honduras Jamaica Netherland Antilles Nicaragua Panama Puerto Rico Trinidad amp Tobago Virgin Islands 102 World Frequency Zones South America 120 V 60 Hz Argentina 230 V 50 Hz 120 V 60 Hz Bolivia 110 V 50 Hz 120 V 50 Hz 60 Hz Brazil 110 127 220 V 60 Hz Chile 220 V 50 Hz Colombia 110 220 V 60 Hz 115 V 60 Hz Ecuador 110 220 V 60 Hz 115 V 50 Hz French Guiana 220 V 50 Hz 110 220 V 60 Hz Guyana 110 240 V 60 Hz 115 V 60 Hz Paraguay 220 V 60 Hz 120 V 60 Hz Peru 220 V 60 Hz 115 120 V 60 Hz Surinam 110 127 V 60 Hz 110 220 V 60 Hz Uruguay 220 V 50 Hz 120 240 V 60 Hz Venezuela 120 240 V 60 Hz 115 230 V 60 Hz 110 220 V 60 Hz 110 220 V 60 Hz 220 V 50 Hz 110 127 V 50 Hz 120 V 60 Hz 120 V 60 Hz 120 V 60 Hz 115 230 V 60 Hz 120 V 60 Hz Australia Oceania Australia Fiji Islands New Zeal
17. on the holder must be free of corrosion and the holder in good condition e Battery contacts The battery contacts must be free of corrosion Once the general condition of the Locator is established the Audio Visual test can be performed 2 Audio Visual display test Upon depressing the trigger the Locator should test the display and speakers by illuminating each segment in the bar display the mode and function indicators and depth display the battery indicator light will illuminate throughout the display test All LCDs must be operative and an audible output must be heard Checking the perform ance Checking depth indica tion 550i only 3 Battery Functional self check If there is no response when the trigger is activated or the low battery illuminates or flashes after the Audio Visual display test the batteries will have to be replaced Use alka line batteries Replace all of the batteries at the same time The purpose of the following procedure is to verify the performance of the Locator It is important that the test is conducted away from areas of electromagnetic interference or over buried services with a large signal radiating off them Switch the Locator on Whilst in Power mode hold down the i Button until the settings are displayed Using the Function Button toggle through the settings until EST is displayed Press the i Button to activate the test Observe the displayed output PAS means unit is
18. the danger of leakage 8 3 Cleaning and Drying Damp products Dry the product the transport container the foam inserts and the accessories at a temper ature not greater than 40 C 104 F and clean them Do not repack until everything is completely dry Cables and plugs Keep plugs clean and dry Blow away any dirt lodged in the plugs of the connecting cables DIGICAT 500i 550i Care and Transport 57 DIGICAT 500i 550i Safety Directions 58 Safety Directions General Introduction 9 9 1 Description 9 2 Permitted use Adverse use The following directions should enable the person responsible for the product and the person who actually uses the equipment to anticipate and avoid operational hazards The person responsible for the product must ensure that all users understand these direc tions and adhere to them Intended Use The products are intended to be used for the following applications Detection and localization of underground services cables and metallic pipes Locator 500i 550i Detection and localization of a Sonde Transmitter Locator 500i 550i Detection and localization of Conductive Rod accessory Locator 550i Estimation of the depth of an underground service a Sonde or Conductive Rod Locator 500i 550i with Bluetooth Data communication with external appliances Use of the product without instruction Use outside of the intended limits Disabling safety system
19. CC part 15 or European directive 1999 5 EC has to be approved prior to use and opera tion 50 Hz to 60 kHz Receive only DIGICAT 500i 550i Technical Data 73 DIGICAT 500i 550i Technical Data 10 2 Typical detection range Operating transmission frequencies Display panel Keypad Integral Speakers Internal battery Transmitter Technical Data 74 Mode Distance Induction mode 150 m 490 ft Connection mode 250m 820 ft 8 192 8 kHz or 32 768 33 kHz 10 segment LED bar graph 4 LED mode indicators LED battery status indicator Led On Off indicator LED signal output indicator 4 membrane push buttons Audio volumes Tone 51 dBA 30 cm 8 kHz mode Low pitched tone 33 kHz mode Higher pitched tone Induction mode Continuous tone Connection mode Pulsed tone when poor or no current output continuous tone when good connection Type Typical operating time 4 x LR14 C alkaline supplied 40 hrs intermittent use at 20 C 68 F in Connection mode Instrument dimensions PEO TD a INCHES 280 mm 11 Inches 260 mm 10 2 Inches Weight Instrument 2 95 kg 6 5 Ibs including batteries Environmental specifi Type Description cations Temperature Operating 20 C to 50 C 4 F to 122 F Storage 40 C to 70 C 40 F to 158 F Protection against With cover open IP54 IEC 60529
20. IGICAT 550i are hereinafter referred to as Locator Differences between the models are marked and described DIGITEX is hereinafter referred to as Transmitter DIGITRACE is hereinafter referred to as Conductive Rod DIGIMOUSE is hereinafter referred to as Sonde The index is at the back of the manual On the Locator and Transmitter you will find a label that shows some important information by means of illustrations You will find some of these illustrations in this manual too This should help to get a clear connection between the instrument label and the information in this manual 1 2 Description A Caution DIGICAT 500i 550i General Information i Series General Information Locators are used to detect buried conductive services emitting an electromagnetic signal which is generated by a current passing through the service Transmitters are used to apply a distinct signal to conductive services which may not radiate electromagnetic signals or may need to be traced for a specific purpose The Transmitter is required to make a depth measurement The Locators and Transmitters described within this manual will greatly increase the detec tion process and help to reduce the dangers and costs associated with service strikes But the very nature of electromagnetic location is dependent on the services being conductive metallic and radiating a signal as current flows through them It is important to remember that a Loca
21. Syria Taiwan Tajikistan Thailand Turkey Turkmenistan United Arab Emirates Uzbekistan Vietnam Yemen 240 V 50 Hz 230 V 50 Hz 110 220 V 60 Hz 240 V 50 Hz 127 220 V 50 Hz 230 V 50 Hz 230 V 50 Hz 220 V 50 Hz 110 220 V 60 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 120 220 V 50 Hz 220 V 50 Hz 105 DIGICAT 500i 550i Index 106 Index C Signal Clamp Conductive Rod epic 83 Functional Check ccccccccccccceesssssecceceeeeesesaeeeeeeees 97 STOMA EE istis doloe deter pe bite eere ER ede 83 Sonde L OPS rat 1 iniret Eeoduc EE 80 Locator STOLASS E E 80 Functional Check oerte oe inue manh gea 88 Transmitter o Operating ents nsa ETAN 75 sepu PR 75 Operating depth range essssssseeeeeeeeen 70 Transmitter S Functional Check oiean EEEE 92 Sonde Typical depth accuracy 70 Functional Check ET 99 Typical detection range DISTANCE 222 2 229 95909099 9 9 a E R UA 74 T Distance along conductor eeeeeeeeeeeeeeee 70 Technical Data ccccceeceeeeeeeeeceeeeeeeeeeeeeeeeeeeeaaeneeeenees 70 Temperature Conductive Rod Operating E 78 STOMA EE 78 Locator Operating E 73 yer de Em 73 Property Connection Set Oe e 81 Storage EUM 81 DIGICAT 500i 550i Index 107 Total Quality Management Our commitment to total customer satisfaction Ee Leica Geosystems AG Heerbrugg Switzerland has been certified as being equipped with
22. amine connection points and remove contamination if a continuous audible output is not achieved e An extension cable is available to extend the red or black cable sets DIGICAT 500i 550i How to Use the Transmitter 37 DIGICAT 500i 550i How to Use the Conductive Rod 38 G 4 1 Description 4 2 Conductive Rod main parts How to Use the Conductive Rod General Information The Conductive Rod is a service tracer enabling small diameter non conductive pipes or ducts to be traced It can be used in Line mode or Sonde mode Conductive Rod Overview a End of Coil Sonde mode Used to accurately pinpoint the end point of the rod 7 M b Rod Line mode bye W Flexible Glass Fibre sheathed which N b incorporates copper wires to conduct the Q signal AW c Signal connection socket Md BW c Used to connect to the Transmitter f d Frame N Houses the flexible rod Can be used in M d both vertical shown and horizontal Q7 DO orientation 4 3 Using the Conductive Rod in Line mode How to Locate a Service Using the Conductive Rod Ui l Insert the rod into the pipe duct conduit or drain until the desired length is in place Connect the Transmitter s cable set to the Transmitter socket and the rod socket in the middle of the frame Separate the black cable and connect the supplied crocodile clip cable connect this to a suitable eart
23. and Solomon Island Tonga 240 V 50 Hz 240 V 50 Hz 230 V 50 Hz 240 V 50 Hz 230 V 50 Hz Europe Albania Austria Belgium Belarus Bulgaria Croatia Czech Republic Denmark Estonia Finland France Germany Greece Hungary Iceland Ireland Italy Latvia Lithuania Luxemburg Moldavia Netherlands Norway Poland Portugal Romania Russia Slovakia 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230V 50Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz DIGICAT 500i 550i World Frequency Zones Slovenia Spain Sweden Switzerland Ukraine United Kingdom Yugoslawia 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz 103 DIGICAT 500i 550i World Frequency Zones Africa Algeria Angola Benin Botswana Burkina Faso Burundi Cameroon Central Africa Rep Chad Congo Dahomey Egypt Ethiopia Gabon Gambia Ghana Ivory Coast Kenya Lesotho Liberia Libya Malawi Mali Mauritania Mauritius Morocco Mozambique Namibia 127 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 127 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50 Hz 220 V 50
24. approved prior to use and opera tion DIGICAT 500i 550i Technical Data 85 DIGICAT 500i 550i International Limited Warranty 86 11 International Limited Warranty International Limited This product is subject to the terms and conditions set out in the International Limited Warranty Warranty which you can download from the Leica Geosystems home page at http www leica geosystems com internationalwarranty or collect from your Leica Geosys tems distributor The foregoing warranty is exclusive and is in lieu of all other warranties terms or conditions expressed or implied either in fact or by operation of law statutory or otherwise including warranties terms or conditions of merchantability fitness for a partic ular purpose satisfactory quality and noninfringement all which are expressly disclaimed DIGICAT 500i 550i International Limited Warranty 87 DIGICAT 500i 550i Functional Checks 88 Appendix A A l Checking the function Functional Checks Locator Functional Check Before any tests can be carried out it is vital to check the status of the unit its batteries and basic functionality The following list is used to achieve this 1 Inspection Casing The casing should be free of significant damage e Labels Body labels must be legible and intact Display label must be free of damage and tears e Battery hatch The hatch must lock into place e Battery holder All the battery contacts and springs
25. ata output Range Example value Description DV 000 to 999 550 Model identifier SN 000000 to 999999 123456 Serial number SV 0 00 to 9 99 3 01 Software version TM 00 00 to 23 59 08 30 Time hh mm default 00 00 no RTC fitted DT 00 00 00 to 01 12 10 Date dd mm yy 31 12 99 default 2 00 00 00 no RTC fitted CM 00 to 15 12 Number of months until next cali bration 00 to 15 ST Oorl 0 Self test O Pass 1 Fail BT O0 to 9 7 Battery level 0 Empty 9 z Good MD O to 4 3 Mode 0 Power 1 Radio 2 8 kHz 3 33 kHz 4 Auto SS 01 to 48 16 Signal strength 01 to 48 UM M or M Units of measurements M or Metres or Imperial DP 0 30 to 3 00 or 125 Depth value displayed depends on value for UM DIGICAT 500i 550i How to Use the Locator 29 DIGICAT 500i 550i How to Use the Transmitter 30 3 3 1 Tracing signal Operating mode Description How to Use the Transmitter General information The Transmitter applies an electrical current signal onto a buried metallic service which enables the service to be traced and identified by the Locator operating in the same mode There are three operating modes for onsite flexibility e 8 kHz for congested site operation e 33 kHz for general usage Combined 8 kHz and 33 kHz available in Connection mode enabling rapid selection and convenience on congested sites The Locator can be used in either mode Active tracing is a t
26. blade of the Locator will be in line with the service when the signal strength indicator is at its minimum Depth Indication 550i only N IM UJ Apply a signal to the service Refer to 3 How to Use the Transmitter for more informa tion Select either 33 kHz or 8 kHz modes to suit the the Trans mitter s output Position the Locator directly over and at 90 degrees to the direction of the service Press and release the i Button The display readout will indi cate the depth of the service and the Line mode icon will be displayed ES e Activating Sonde depth will provide an inaccurate readout Always use chalk or paint to mark services never pegs or other material which are driven into the ground Additional services may be within the excavation zone as well as the service you are taking a depth reading from e The reading will be more accurate when taken over a straight run where the service does not bend or have a service crossing it or coming off it Depth shown and actual depth dl Depth shown on the DIGICAT depth to the centre of the line d2 Actual depth of the service Note the difference between d1 and d2 A Warning The depth reading might not reflect the real depth if your Locator picks up the signal induced into the service by the Transmitter
27. ce Signal Strength indicator Scrolls through in sequence once Mode indicators Briefly illuminated Battery indicator On throughout Bluetooth and wrench Briefly illuminated Measurement unit Briefly illuminated display readout depth mode indicator The unit will then go into Power mode maximum sensitivity Locating process The locating process is split into three steps Sweep Search e Pinpointing the service Direction of the service DIGICAT 500i 550i How to Use the Locator 19 DIGICAT 500i 550i How to Use the Locator 20 Sweep Search The unit will automatically Chus s gt select Power mode and maximum sensitivity K Auto mode combines the benefit of simultaneous detection in Power and Radio modes and helps to confirm the presence of services upon initial site occupation Improved defi nition of the service will be provided by single mode operation Define the area to be excavated 2 In Power mode cross the site from left to right keeping the Locator upright taking care not to swing the unit Turn through 90 degrees and repeat E Ensure that the Locator is held in an upright position and close to the ground 3 Continue the sweep until either a signal is located or you are satisfied that the area has been adequately tested C In the presence of a service emitting a traceable signal a tone will be emitted and the signal strength indicator will rise and fal
28. ed with household waste Dispose of the product appropriately in accordance with the national regulations in force in your country Always prevent access to the product by unauthorised personnel Product specific treatment and waste management information can be downloaded from the Leica Geosystems home page at http www leica geosystems com treatment or received from your Leica Geosystems dealer DIGICAT 500i 550i Safety Directions 63 DIGICAT 500i 550i Safety Directions 64 A Caution A Warning A Warning A Warning 9 6 Description During the transport shipping or disposal of batteries it is possible for inappropriate mechanical influences to constitute a fire hazard Precautions Before shipping the product or disposing of it discharge the batteries by running the product until they are flat When transporting or shipping batteries the person in charge of the product must ensure that the applicable national and international rules and regulations are observed Before transportation or shipping contact your local passenger or freight transport company High mechanical stress high ambient temperatures or immersion into fluids can cause leackage fire or explosions of the batteries Precautions Protect the batteries from mechanical influences and high ambient temperatures Do not drop or immerse batteries into fluids If battery terminals come in contact with jewellery keys metallised paper or other metals
29. erm frequently used when a Transmitter is used to apply a signal to a service enabling it to be traced The use of a Transmitter will greatly improve the detection of services especially ones which may not have a signal on them The signal from the Transmitter can be applied to services in two ways Induction mode 8 kHz or 33 kHz Induction is a quick and simple way to apply a signal to a service without the need to make any physical connection to it The Transmitter uses an internal aerial to transmit the signal therefore it should be noted that the signal will apply itself to additional serv ices within close proximity to the Transmitter Connection mode 8 kHz or 33 kHz or combinded 8 kHz and 33 kHz This is the most efficient way of applying a signal to a service and should be used when ever possible The Transmitter s cable set or any of the available accessories are connected to the service which is to be traced or identified cS e 8 kHz is less likely to apply itself to additional services making tracing in areas of multiple services easier e 33 kHz is suitable for general site use Combined 8 and 33 kHz Connection mode only is useful in congested areas when either 8 or 33 kHz may provide a better result The best results can be simply achieved by switching modes on the Locator DIGICAT 500i 550i How to Use the Transmitter 31 DIGICAT 500i 550i How to Use the Transmitter 32 3 2 Transmitter Overview Transmitter
30. f and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user s authority to operate the equipment DIGICAT 500i 550i Safety Directions 67 DIGICAT 500i 550i Safety Directions 68 Labelling Locator Type Art No S No Power 9V 200mA max E a C X Leica Geosystems AG CH 9435 Heerbrugg A Made in the UK This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Ej Labelling Transmitter Power 6V Nom 300mA Max Made in the UK uc This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation
31. fferent ne sockets are integrated DIGICAT 500i 550i Technical Data 71 DIGICAT 500i 550i Technical Data Internal battery Type 6 x LR6 AA alkaline Typical operating time 40 hrs intermittent use at 20 C 68 F in 8 kHz mode or 33 kHz mode 72 Instrument dimensions NE mm 3 4 Inches ZA 760 mm 30 Inches Y aee 250 mm 10 Inches Weight Instrument 2 7 kg 6 Ibs including batteries Environmental specifi cations Conformity to national regulations Frequency band Output power Type Description Temperature Operating 20 C to 50 C 4 F to 122 F Storage 40 C to 70 C 40 F to 158 F Protection against Water Dust IP54 IEC 60529 and Sand Dust protected Humidity 9596 RH non condensing The effects of condensation are to be effectively counteracted by periodically drying out the product e FCC Part 15 applicable in US e Hereby Leica Geosystems AG declares that the DIGICAT 500i 550i is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at http www leica geosystems com ce Class 1 equipment according European Directive 1999 5 EC R amp TTE can be placed on the market and be put into service without restrictions in any EEA member state The conformity for countries with other national regulations not covered by the F
32. h point Switch the Transmitter on and select 8 kHz or 33 kHz A good signal is indicated when the audible output from the Transmitter is constant The signal applies itself evenly along the length of the Conductive Rod Trace the length of the rod using the Locator set to the same frequency Ensure there are no services below the ground when using the earth pin Use the Locator in advance e At least half the Conductive Rod needs to be uncoiled when in use DIGICAT 500i 550i How to Use the Conductive Rod 39 DIGICAT 500i 550i How to Use the Conductive Rod 40 Using the Conductive 1 Insert the rod into the pipe duct conduit or drain until the desired length is in place Rod in Sonde mode 2 Connect the cable set to the Transmitter socket and the rod socket in the middle of the frame The black cable must be connected directly between Transmitter and Conductive Rod 3 Switch the Transmitter on and select 8 kHz or 33 kHz A good signal output is indicated when the audible output from the Transmitter is constant The majority of the signal is concentrated towards the Sonde 4 Trace the length of the rod using the Locator set to the same frequency cS At least half the Conductive Rod needs to be uncoiled when in use DIGICAT 500i 550i How to Use the Conductive Rod 41 DIGICAT 500i 550i How to Use the Signal Clamp 42 5 How to Use the Signal Clamp 5 1 General Information Description The Signal
33. hen the signal is produced by a sonde lying in a large diameter conduit The depth reading may not indicate the real depth of the service especially if the sonde is lying at the base of a large diameter duct Precautions Always compensate depth reading for service size Information code Description Information on instrument label The service is too shallow to register prop metres erly metres ft inch ft inch 0 3m 1ft 25 DIGICAT 500i 550i How to Use the Locator 26 Information code Description Information on instrument label ae paga re un metres ft inch The service is too deep metres ft inch The signal received by the Locator is too small to register properly The signal received by the Locator is too large to register properly Information code Description Information on instrument label Depth function not available The Locator is set to the wrong mode for a depth reading to be taken DIGICAT 500i 550i How to Use the Locator 27 DIGICAT 500i 550i How to Use the Locator 28 2 6 B
34. ice DIGICAT 500i 550i How to Use the Transmitter 35 DIGICAT 500i 550i How to Use the Transmitter 36 Using the Transmitter in Connection mode UJ Ui Switch the Transmitter on and observe the battery level Change batteries when indi cated Plug the Transmitter s cable set into the connection socket the Transmitter will go into Connection mode as indicated on the mode display Connect the red cable to the service a magnet is provided to assist on large services Connect the black cable to earth pin ensuring that no services are below push the earth pin into the ground A good level of tracing signal is indicated when the audible output changes from pulsed to continuous and the signal level output goes to maximum Select 8 kHz 33 kHz or combined 8 and 33 kHz mode Adjust output if required Trace the signal using the Locator set to the same operating mode Refer to 2 How to Use the Locator for more information A Danger Connecting the cable set to a live service can result in receiving an electric shock Precautions The connection cable set should never be connected directly to a live service cS Ensure there are no services below the ground when using the earth pin Use the Locator in advance The black cable can be connected to other metallic structures which go into the ground e n dry conditions it may be necessary to add water around the earth point to get a good connection Ex
35. ict regulations and standards which are in force in this respect Leica Geosystems cannot completely exclude the possibility that other equip ment may be disturbed or that humans or animals may be affected Do not operate the product with radio or digital cellular phone devices in the vicinity of filling stations or chemical installations or in other areas where an explosion hazard exists Do not operate the product with radio or digital cellular phone devices near to medical equipment e Do not operate the product with radio or digital cellular phone devices in aircraft Do not operate the product with radio or digital cellular phone devices for long periods with it immediately next to your body 9 7 A Warning A Warning FCC Statement Applicable in U S This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a partic ular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment of
36. ignal Clamp Sonde DIGICAT 500i 550i General Information 11 DIGICAT 500i 550i How to Use the Locator 12 2 2 1 Operating modes Electromagnetic signals Passive signals Active tracing Depth indication 550i only Wireless communica tion Bluetooth Hazard zone Peak hold How to Use the Locator General Information e Passive modes Power and Radio Active modes 8 kHz and 33 kHz Auto mode Combined Power and Radio modes An electromagnetic signal radiates from buried conductive services as an electrical current flows through them The Locator processes these signals and displays their presence Some signals are already present on buried services and can be readily detected by the Locator We call these passive signals These signals are generated by power distribution systems and radio transmitters Some conductive services do not emit passive signals These services may be traced by applying a signal to the service by using a transmitter Depth indication is only available with the 550i Locator used in conjunction with the Trans mitter or Sonde The displayed depth is to the centre of the service or to the Sonde Data can be wirelessly transferred from the Bluetooth enabled Locator to devices which are designed to accept the information Provides an additional alarm indicating the close proximity of a service emitting a Power 8 kHz or 33 kHz signal Assists in pinpo
37. information about electromagnetic compatibility provided by the manufacturer Disturbances caused by electromagnetic radiation can result in erroneous measurements Although the product meets the strict regulations and standards which are in force in this respect Leica Geosystems cannot completely exclude the possibility that the product may be disturbed by very intense electromagnetic radiation for example near radio Transmit ters two way radios or diesel generators Precautions Check the plausibility of results obtained under these conditions If the product is operated with connecting cables attached at only one of their two ends for example external supply cables interface cables the permitted level of electromagnetic radiation may be exceeded and the correct functioning of other products may be impaired Precautions While the product is in use connecting cables for example product to external battery product to computer must be connected at both ends DIGICAT 500i 550i Safety Directions 65 DIGICAT 500i 550i Safety Directions 66 A Warning Only with Transmitter and Sonde Electromagnetic fields can cause disturbances in other equipment in installations in medical devices for example pacemakers or hearing aids and in aircraft It can also affect humans and animals Precautions Although the product meets in combination with radio or digital cellular phone devices recommended by Leica Geosystems the str
38. inting a service by displaying the peak reading for a short period of time 2 2 Locator Overview Locator main parts a b C d e f CE The case foot can be replaced if it is worn ised service workshop Display Panel Contains the operational controls Speakers mounted internally left and right Active at power on and when a signal is detected On Off Trigger Press and hold the trigger to activate the Locator Release the trigger to deactivate Battery Hatch Release Pressing the yellow release button unlocks the battery hatch allowing access to the battery compartment Battery Compartment 6 x LR6 AA alkaline batteries are used Replace all batteries when indicated Case Foot Contact your agency or Leica Geosystems author DIGICAT 500i 550i How to Use the Locator 13 DIGICAT 500i 550i How to Use the Locator Display panel overview SSS SSS SSS J Gxt Ss SS Ss SS Ss 2 SS SS metres E SS p SS SS E E c E B E fcinel T 49 0 p 100000 a b C d e 14 Signal Strength Indicator Indicates the response of the Locator to a signal service Mode Indicators Displays the selected mode Power Radio 8 kHz 33 kHz Auto as shown from bottom to top Function Button Selects operating mode Light Sensor Automa
39. ion 8 192 8 kHz or frequencies 32 768 33 kHz Internal battery Type Typical operating time 1 x LR6 AA alkaline 40 hrs intermittent use at 20 C 68 F in 8 kHz mode or 33 kHz mode Instrument dimensions 038 mm 1 5 Inches lt 8kHz 7 it 33kHz g 120 mm 4 7 Inches Weight Instrument including batteries 0 18 kg 0 4 Ibs DIGICAT 500i 550i Technical Data 79 DIGICAT 500i 550i Technical Data Environmental specifi cations Conformity to national regulations 80 Type Description Temperature Operating 20 C to 50 C 4 F to 122 F Storage 40 C to 70 C 40 F to 158 F Protection against Water Dust Fully submersible and Sand Humidity 95 RH non condensing The effects of condensation are to be effectively counteracted by periodically drying out the product e FCC Part 15 applicable in US e Hereby Leica Geosystems AG declares that the DIGIMOUSE is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at http www leica geosystems com ce Class 1 equipment according European Directive 1999 5 EC R amp TTE can be placed on the market and be put into service without restrictions in any EEA member state The conformity for countries with other national regulations not covered by the FCC part 15 or
40. ionality To carry out this test the following are required ALocator to detect the signals Atest area free of services as illustrated 1 Inspection e Casing The casing should be free of significant damage e Labels Body labels must be legible and intact Display label must be free of damage and tears e Battery hatch The hatch must lock into place e Battery holder All the battery contacts and springs on the holder must be free of corrosion and the holder in good condition e Battery contacts The battery contacts must be free of corrosion Once the general condition of the Transmitter is established the Audio Visual test can be performed 2 Audio Visual display test Turn on the Transmitter The LED display will illuminate and the speakers will emit a tone the battery output level indicator will illuminate throughout the test All LEDs must be oper ative and an audible output must be heard 3 Battery check Battery status is momentarily indicated after the Audio Visual display test The battery level indicator will indicate the condition of the battery When the batteries need replacing the battery indicator will flash Use alkaline batteries Replace all of the batteries at the same time 4 Inductive mode check Turn on the Transmitter and Locator both set to 33 kHz mode At a distance of 2 m 6 56 ft the Locator should detect and indicate with both the audio and visual indicators Change the Transmitter and Locator m
41. l as you pass over it 4 Repeat the Sweep Search process in Radio mode K The Sweep Search must be conducted in Power and Radio modes as a minimum as not all services including some electrical ones emit a power signal These services may be found using Radio mode or active modes Cs Hazard zone can be operated in Power 8 kHz 33 kHz and Auto modes and provides an additional alarm to the presence of buried services which may be within close proximity Pinpointing the service m E Retrace your steps to the area where the highest signal reading peak response was obtained The service is directly below the Locator when the signal strength indicator is at its maximum The audio output will automatically adjust to facilitate pinpointing over the service and automati cally reset when the signal strength indicator drops to its minimum position cE Always use chalk or paint to mark services never pegs The signal strength indicator does not indicate the size depth or type of a service Peak hold When activated peak hold will show the highest peak reading obtained during the pinpoint process The displayed reading can be adjusted between 0 to 5 seconds DIGICAT 500i 550i How to Use the Locator 21 DIGICAT 500i 550i How to Use the Locator Detecting direction of the service l 2 3 22 Position the Locator directly over the service Rotate the Locator on its axis The
42. luetooth Pairing information Wireless Data Communication where applicable Bluetooth connectivity is an optional extra available on the 500i and 550i Locators Data can be wirelessly transferred from the Locator to a suitable data logging device enabling the operator to capture information about the Locator s status and the service depth When the Locator is paired to a suitable logger the Bluetooth symbol will flash and the unit will transmit data periodically Important information for pairing The Locator must be switched on throughout the process Follow the instructions on the logger for pairing Refer to the manufacturer s instruc tions Device Name Model Number Serial Number for example 550 000001 Pass key 12345 The Bluetooth symbol will flash continually when the devices have successfully paired e When a depth reading has been taken the Locator will display LOG To transfer the infor mation to the data logger press the i Button whilst LOG is displayed Whilst the Locator is calculating depth the data output stops e If there is no wireless communication then the LOG function will not be displayed and the unit will function as a Locator The Locator will output ASCII text Refer to ASCII text description for more information ASCII text description ASCII output pattern DV xxSN ooxSVxxTIVboxxDTdd mm yy CMXxxCMxSTXxBTxxMDxxSSxxUMxxDPXX D
43. odes to 8 kHz and repeat The speed of the audio pulsed output of both Transmitter and Locator should slow down Pa Sy 2 m 6 56 ft chm 6AR 5 Output signal level check Press the output level control button the indicated power should reduce to minimum and then increase with repeated presses until the maximum level is again reached DIGICAT 500i 550i Functional Checks 93 DIGICAT 500i 550i Functional Checks 94 6 Connection mode check With the Transmitter operating in the 33 kHz Induction mode plug in the transmitter s cable set The pulsing audio tone should change and the connection induction LED change to indi cate that the output has automatically changed over to the connection mode Connect the transmitter s cable set together the output audio tone should change from pulsed to continuous and the Level meter display should read maximum Turn on the Locator set to 33 kHz mode and place it over one of the output connection cables The Locator should detect and indicate with both audio and visual indicators Change the Transmitter and Locator modes to 8 kHz and repeat The speed of the audio pulsed output of the Transmitter should slow down Cs If any of these tests give no response or a significantly different response from normal the Transmitter should be returned for service Functional test check list Functional Test Check List Replace Unit Serial Number Comments Tran
44. oint at the centre This is an accurate method but it is essential to ensure the Sonde is vertical DIGICAT 500i 550i How to Use the Sonde 55 DIGICAT 500i 550i Care and Transport 56 8 8 1 Transport in the field Transport in a road vehicle Shipping Shipping transport of batteries 8 2 Product Care and Transport Transport When transporting the equipment in the field always make sure that you carry the product in its original transport container Never carry the product loose in a road vehicle as it can be affected by shock and vibration Always carry the product in its transport container and secure it When transporting the product by rail air or sea always use the complete original Leica Geosystems packaging transport container and cardboard box or its equivalent to protect against shock and vibration When transporting or shipping batteries the person in charge of the product must ensure that the applicable national and international rules and regulations are observed Before transportation or shipping contact your local passenger or freight transport company Storage Respect the temperature limits when storing the equipment particularly in summer if the equipment is inside a vehicle Refer to 10 Technical Data for information about tempera ture limits If the equipment is to be stored for a long time remove the alkaline batteries from the product in order to avoid
45. onnection Set 46 6 1 General Information 46 6 2 Property Connection Set Overview 46 6 3 How to Locate a Service Using the Property Connection Set 47 How to Use the Sonde 50 7 1 General Information 50 7 2 Sonde Overview 50 7 3 How to Locate a Service Using the Sonde 53 Care and Transport 56 8 1 Transport 56 8 2 Storage 56 8 3 Cleaning and Drying 57 Safety Directions 58 9 1 General Introduction 58 9 2 Intended Use 58 9 3 Limits of Use 59 9 4 Responsibilities 59 9 5 Hazards of Use 60 9 6 Electromagnetic Compatibility EMC 64 9 7 FCC Statement Applicable in U S 67 5 DIGICAT 500i 550i Table of Contents DIGICAT 500i 550i Table of Contents 10 Technical Data 70 10 1 Locator i Series Technical Data 70 10 2 Transmitter Technical Data 74 10 3 Conductive Rod Technical Data 77 10 4 Sonde Technical Data 79 10 5 Property Connection Set Technical Data 81 10 6 Signal Clamp Technical Data 83 11 International Limited Warranty 86 AppendixA Functional Checks 88 A 1 Locator Functional Check 88 A 2 Transmitter Functional Check 92 A 3 Conductive Rod Functional Check 97 A 4 Sonde Functional Check 99 Appendix B World Frequency Zones 102 Index 106 DIGICAT 500i 550i Table of Contents DIGICAT 500i 550i General Information 1 1 1 er Naming convention Index Instrument label General Information How to Use this Manual It is recommended to set up the product while reading through this manual DIGICAT 500i D
46. ons Always excavate with care Only with a Locator with depth The depth reading might not reflect the real depth if your Locator picks up the signal induced into the service by the Transmitter This signal is radiated from the centre of the service This is even more important when the signal is produced by a Sonde lying in a large diameter conduit Precautions Always compensate depth reading for service size DIGICAT 500i 550i Safety Directions 61 DIGICAT 500i 550i Safety Directions 62 A Danger A Danger A Danger A Danger The Locator may fail to detect electrical services in Power mode if an incorrect power setting is used Precautions Before use verify the Locator is setup to be compatible with mains frequency supply in your country Options are 50 or 60 Hz Refer to Appendix B World Frequency Zones for more information Contact your agency or Leica Geosystems authorised service workshop if your unit is incor rectly configured for your region Only with Transmitter A hazardous signal may be present on the connection plug of the Signal Clamp when clipped over a live service Precautions The clamp should be connected to the Transmitter before clamping around a live service Connecting the Transmitter s cable set to a live service can result in receiving an electric shock Precautions The Transmitter s cable set should never be connected directly to an electrical live service When
47. p and M10 connection point The thread on the Sonde is a male M10 and comes with adaptors to both British and Euro pean drain rods Changingthefrequency Changing to 33 kHz mode output 1 otf xk gt R DIGICAT 500i 550i How to Use the Sonde l Unscrew and remove end cap Insert battery positive end first Refit end cap securely Hold Sonde upright Confirm green LED is continuous Wait approximately 10 seconds for the green LED to start flashing With the green LED flashing the Sonde is ready for use at 33 kHz 51 DIGICAT 500i 550i How to Use the Sonde Changing to 8 kHz mode Teri HTD w Ww j I Z 52 Unscrew and remove end cap Insert battery positive end first Refit end cap securely Hold Sonde upright Confirm green light is continuous Rotate Sonde so the LED points down and wait approxi mately 1 second Rotate Sonde upright Confirm the amber coloured LED is continuous If LED remains green repeat from step 1 Wait approximately 10 seconds for the amber LED to start flashing With the amber LED flashing the Sonde is ready for use at 8 kHz 5 10 sec 4MI xk 6 d 8kHz S Once the function of the Sonde has been checked with a Locator set to the same operating mode it can be attached to drain rods or other means of guiding it into the service being traced 7 3 How to Locate a Service U
48. ransmitter is activated On test Test pattern mm E ELI ELCHE YS aa N n N AS wats 4 Audio output On throughout test sequence LEDs LEDs are all lit throughout the test sequence Battery low indication Battery level is shown throughout the test sequence flashes if batteries are low Default mode selection 33 kHz and maximum output level are automatically selected Induction mode output is selected unless the transmitter s cable set or accessories are connected Using the Transmitter in Induction mode Place the Transmitter over the service with the arrows on top of the case lid running in line with the suspected direction of the service Switch the Transmitter on and observe the battery level Change batteries when indi cated Select 8 kHz or 33 kHz mode adjust output if required The tracing signal is induced directly onto the service from the internal aerial Trace the path of the service using the Locator set to the same frequency Refer to 2 How to Use the Locator for more information Work at least 10 m 33 ft away from the Transmitter to avoid airborne signals Reposi tion the Transmitter if required Coupling efficiency is best at 33 kHz The signal will couple to adjacent services dependent on depth and direction Reducing the signal output can help to increase the battery life and the Transmitter is less likely to apply a signal to an adjacent serv
49. re required e A Transmitter for generating the signal in the Sonde and Line mode tests The cable set for the Conductive Rod Insert the Conductive Rod s cable set into the Transmitter and Conductive Rod Ensure the black cable is connected Switch the Transmitter on The audible output from the Trans mitter must be constant Adjust the signal output on the Transmitter to minimum the audible output must be constant Part the black cable set in the middle the audible output must be pulsed If any of these tests give no response or a significantly different response from normal the Conductive Rod should be returned for service DIGICAT 500i 550i Functional Checks 97 DIGICAT 500i 550i Functional Checks Functional test check list 98 Functional Test Check List Unit Serial Number Comments Conductive Rod Test Operative Fail analysis Notes Yes No N A 1 Sonde mode Repair or replace Faulty cable Transmitter audio output does not go continuous cable set 2 Sonde mode Locator does not detect signal Return for repair Replace One or both internal wires are open or short circuit 3 Line mode Locator does not detect signal Return for repair Replace One or both internal wires are open or short circuit Tested by Date A 4 Checking the function Sonde Functional Check The purpose of the following procedure is to
50. roved prior to use and opera tion 10 6 Operating transmission frequencies Instrument dimensions Weight Environmental specifi cations Signal Clamp Technical Data 32 768 33 kHz when used with a signal transmitter set in 33 kHz mode 250 mm 9 8 Inches 142 mm 5 6 Inches 100 mm 4 Inches Instrument 0 354 kg 0 76 Ibs Type Description Temperature Operating 20 C to 50 C 4 F to 122 F Storage 40 C to 70 C 40 F to 158 F Protection against Water Dust IP54 IEC 60529 and Sand Dust protected DIGICAT 500i 550i Technical Data 83 DIGICAT 500i 550i Technical Data 84 Type Description Humidity 9596 RH non condensing The effects of condensation are to be effectively counteracted by periodically drying out the product Conformity to national e FCC Part 15 applicable in US regulations e Hereby Leica Geosystems AG declares that the Signal Clamp is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The declaration of conformity may be consulted at http www leica geosystems com ce Class 1 equipment according European Directive 1999 5 EC R amp TTE can be placed on the market and be put into service without restrictions in any EEA member state The conformity for countries with other national regulations not covered by the FCC part 15 or European directive 1999 5 EC has to be
51. s Removal of hazard notices Opening the product using tools for example screwdriver unless this is specifically permitted for certain functions Modification or conversion of the product Use after misappropriation A Warning 9 3 Environment A Danger 9 4 Manufacturer of the product Manufacturers of non Leica Geosystems accessories Use of products with obviously recognizable damages or defects Use with accessories from other manufacturers without the prior explicit approval of Leica Geosystems Inadequate safeguards at the surveying site for example when measuring on roads Adverse use can lead to injury malfunction and damage It is the task of the person respon sible for the equipment to inform the user about hazards and how to counteract them The product is not to be operated until the user has been instructed on how to work with it Limits of Use Suitable for use in an atmosphere appropriate for permanent human habitation not suitable for use in aggressive or explosive environments Local safety authorities and safety experts must be contacted before working in hazardous areas or in close proximity to electrical installations or similar situations by the person in charge of the product Responsibilities Leica Geosystems AG CH 9435 Heerbrugg hereinafter referred to as Leica Geosystems is responsible for supplying the product including the user manual and original accessories in
52. sed service workshop if your unit is incor rectly configured for your region T 1 Replace the batteries when the battery s TT status indicator is empty orn 2 Press the yellow release button to unlock the Battery Hatch Remove the battery holder from the Locator er POs 3 Replace all batteries with six new LR6 AA batteries CE Alkaline batteries should be used 2 4 Hazard Zone Description Provides an additional warning to the close proximity of buried services and functions in the following modes Power 8kHz e 33 kHz Auto mode Power mode only Hazard zone status am Status indicator Description indicators T Hazard zone is switched on Hazard zone on and is alarming OE d Hazard zone is switched off DIGICAT 500i 550i How to Use the Locator 17 DIGICAT 500i 550i How to Use the Locator 18 A Caution The absence of a positive indication does not guarantee the non existence of a service Services without a detectable signal may be present The Locators can only locate non metallic services such as plastic pipes typically used by the water and gas utilities with the use of appropriate accessories Precautions Always excavate with care 2 5 How to Locate a Service Start up test The following test sequence will take place every time the Locator is activated On test Test pattern Info on label Audio Output On throughout test sequen
53. sing the Sonde Locating the Sonde 1 Walk in line with the suspected direction of travel observing the display The signal strength indicator will rise and fall as you pass over the ghost signal at the back of the Sonde the peak signal directly over the Sonde and the ghost signal at the front The numeric signal strength indi cator will display its highest value when detecting the peak signal 2 Retrace your steps and position the locator directly over the peak signal Move the locator left and right until the highest numeric reading is obtained This reading will indicate the Sonde s precise location DIGICAT 500i 550i How to Use the Sonde 53 DIGICAT 500i 550i How to Use the Sonde 54 3 Depth indication 550i only Depth indicationcan be used with a suitable depth locator The locator must be posi tioned directly over the Sonde and in line with it rotate the locator on its axis to find the highest reading Press and hold the i Button for 2 seconds The depth of the Sonde will be displayed in the depth readout window and the Sonde mode icon will be visible beneath the display ES For ease and convenience mark the ground every 3 to 4 metres For ease of use practice the process above ground Tracing a walk C If a walk through sewer is being through sewer traced another method is to place the Sonde vertically for example to pinpoint a buried manhole The Locator will pick up a pool of signal with a null p
54. smitter Test Operative Fail analysis Notes Yes No N A 1 Casing Return for repair Casing should be free of damage Labels Return for repair Replace Body labels must be legible and intact Display label must be free of damage and tears Battery cover and accessory cover Return for repair Replace Hatches must lock into place Battery contacts Return for repair Contacts must be free of corrosion Audio Visual display test Return for repair All LEDs must illuminate and an audible output must be heard Batteries Replace Replace alkaline batteries if exhausted no response or if the battery indicator light is illuminated or flashing after display test Replace all batteries DIGICAT 500i 550i Functional Checks 95 DIGICAT 500i 550i Functional Checks 96 Functional Test Check List 7 Induction mode Return for repair Replace Reduced or no output signal 8 Connection mode no change in audio indication Return for repair Replace Faulty cable 9 Connection mode no change in audio indication Return for repair Replace No output signal Tested by Date A 3 Checking the function Conductive Rod Functional Check The purpose of the following procedure is to verify the performance of the Conductive Rod To carry out this test the following a
55. st be free of corrosion 4 Battery holder Replace Holder must be free of corro sion 5 Battery contacts Return for repair Contacts must be free of corrosion 6 Audio Visual display test Return for repair LCD is illuminated and an audible output must be heard Functional Test Check List 7 Batteries Replace Replace alkaline batteries if pack is exhausted no response or if the battery indicator light is illuminated or flashing after display test Replace all batteries 8 Power mode Return for repair Response width and peak value similar to test unit 9 Radio mode Return for repair Response width and peak value similar to test unit 10 8 kHz Return for repair Response width and peak value similar to test unit 11 33 kHz Return for repair Response width and peak value similar to test unit 12 Depth Mode 550i only 8 kHz and 33 kHZ Return for repair Gives same result as test unit 1096 accuracy Tested by Date DIGICAT 500i 550i Functional Checks 91 DIGICAT 500i 550i Functional Checks 92 A 2 Checking the function Transmitter Functional Check The purpose of the following procedure is to verify the performance of the signal Trans mitter Before any tests can be carried out it is vital to check the status of the unit its batteries and basic funct
56. strength indicator CST Adjusts display s contrast 0 15 M I Displays unit of measurement CAL Displays the next service date DD MM YY CON Displays supplier company name TEL Displays supplier company telephone number I D Displays the operator s name PWR Displays the power mode regional setting Refer to Appendix B World Frequency Zones for more information SR Displays unit serial number VER Displays software version DIGICAT 500i 550i How to Use the Locator 15 DIGICAT 500i 550i How to Use the Locator 16 Accessing and adjusting the settings A Danger Changing the battery l 2 NOW NW Switch the Locator on Ensure the Locator is in Power mode If required press Function Button to select mode Depress i Button for 2 seconds The user settings will be displayed in the display readout Press Function Button to toggle through to desired setting Press i Button to select the setting Press Function Button to activate adjust Press i Button to store and exit The Locator may fail to detect electrical services in Power mode if an incorrect power setting is used Precautions Before use verify the Locator is setup to be compatible with mains frequency supply in your country Options are 50 or 60 Hz Refer to Appendix B World Frequency Zones for more information Contact your agency or Leica Geosystems authori
57. tically switches the displays backlight on or off to suit light conditions Battery Indicator Indicates the battery condition Segment illumina tion decreases as battery condition declines Replace the batteries when the battery indicator is empty Bluetooth optional extra Indicates the Locator is paired to another device Wrench Indicates the Locator requires periodic service or unit is faulty h Measurement Unit Depth indication with 550i Indicates depth indication is in metric or feet and inches i Display Readout Alpha numeric matrix indicates system set up and depth indication j Depth Mode Indicators Indicates a depth reading to a service or a Sonde 550i only Service icon used to indicate Hazard zone on 500i and 550i k i Button Used to access the user settings and to provide a depth readout for the 550i 2 3 Locator Setup and Information Locator settings The i Series Locators offer a range of settings which the operator can adjust to their own preference It also displays additional service and contact information as detailed Setting Description EST Performs a function check on the locators hardware and software displaying PAS if the Locator is within predefined tolerance or ERR if the locator it is not H Z Switches hazard zone on or off VOL Adjust volume level O 10 HLD Adjust peak hold duration 0 5 seconds SSI Displays a numeric signal
58. to the mains supply Precautions The Property Connection Set should be connected to the Transmitter before connecting to the mains supply A hazardous signal may be present on the service or mains outlet causing personal harm Precautions Do not use on electrical services which have impaired or no insulation If in doubt do not use DIGICAT 500i 550i How to Use the Property Connection Set 49 DIGICAT 500i 550i How to Use the Sonde 7 7 1 Description e 7 2 Sonde main parts 50 How to Use the Sonde General Information The Sonde is a dual frequency signal transmitter used to trace drains sewers and other non conductive services It can be attached to a range of equipment including drain rods boring tools and inspection cameras It is powered by a 1 5 V LR6 AA battery so unlike other accessories this does not require a connection to the transmitter The signal pattern transmitted from the Sonde is different to that which is radiated from a service transmitting a peak signal over its main body with a ghost signal at the front and back This requires the Sonde to be traced with its own unique method The i Series Locators feature a numeric signal strength indicator user setting SSI set to ON which will greatly improve the locating process The numeric signal strength indicator is shown in the display readout on the Locator Sonde Overview a LED b Sonde body c LR6 AA battery d End ca
59. tor on its own will not detect all services and care should be taken when excavating It is generally accepted that a safe system of work should be adopted which would include planning the work in advance the use of utility maps the use of Locators and Transmitters and the use of safe digging practices The absence of a positive indication does not guarantee the non existence of a service Services without a detectable signal may be present The Locators can only locate non metallic services such as plastic pipes typically used by the water and gas utilities with the use of appropriate accessories Precautions Always excavate with care DIGICAT 500i 550i General Information 10 Accessories Designed to increase the detection of services with no or little signals on them Generally work in conjunction with the Locator and Transmitter Functional Check Designed to demonstrate the equipment is working satisfactorily in between service inter vals Refer to Appendix A Functional Checks for more information 1 3 General information i Series instruments overview i Series accessories overview i Series Instruments and Accessories The i Series is a collection of products used to locate buried metallic and nonmetallic serv ices a b Locator Transmitter a b c d e Conductive Rod non metallic service tracer Extension Cable Property Connection Set S
60. using a signal clamp a hazardous signal may be present on the service causing personal harm Precautions Do not use on electrical services which have impaired or no insulation If in doubt do not use A Danger A Warning A Warning When using a Property Connection Set a hazardous signal may be present on the service or mains outlet causing personal harm Precautions Do not use on electrical services which have impaired or no insulation If in doubt do not use Inadequate securing of the surveying site can lead to dangerous situations for example in traffic on building sites and at industrial installations Precautions Always ensure that the survey site is adequately secured Adhere to the regulations governing safety and accident prevention and road traffic If the product is improperly disposed of the following can happen f polymer parts are burnt poisonous gases are produced which may impair health f batteries are damaged or are heated strongly they can explode and cause poisoning burning corrosion or environmental contamination e By disposing of the product irresponsibly you may enable unauthorised persons to use it in contravention of the regulations exposing themselves and third parties to the risk of severe injury and rendering the environment liable to contamination Improper disposal of silicone oil may cause environmental contamination Precautions The product must not be dispos
61. which if not avoided may result in minor or moderate injury and or appreciable material financial and environmental damage CE Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner Validity of this manual This manual applies to all DIGISYSTEM instruments which are the i Series Differences between the various instruments and models are marked and described DIGICAT 500i 550i Introduction DIGICAT 500i 550i Table of Contents Table of Contents In this manual Chapter Page 1 General Information 8 1 1 How to Use this Manual 8 1 2 i Series General Information 9 1 3 i Series Instruments and Accessories 11 2 How to Use the Locator 12 2 1 General Information 12 2 2 Locator Overview 13 2 3 Locator Setup and Information 15 2 4 Hazard Zone 17 2 5 How to Locate a Service 19 2 6 Wireless Data Communication where applicable 28 3 How to Use the Transmitter 30 3 1 General information 30 3 2 Transmitter Overview 32 3 3 How to Locate a Service Using the Transmitter 34 4 How to Use the Conductive Rod 38 4 1 General Information 38 4 2 Conductive Rod Overview 38 4 3 How to Locate a Service Using the Conductive Rod 39 How to Use the Signal Clamp 42 5 1 General Information 42 5 2 Signal Clamp Overview 42 5 3 How to Locate a Service Using the Signal Clamp 43 How to Use the Property C
62. within set tolerances ERR means unit is outside set tolerances and may need servicing U1IiUN rnm Repeat the test in a different location if the units displays ERR The Locator will automatically repeat the function test if it fails Repeated failure will indicate a faulty unit which must be returned for service This test can be carried out provided the depth of a service on the test area is known Switch the Locator on and ensure that it is in 33 kHz mode Position the Locator directly over and at right angle to the service Press and release the i Button to activate the depth measurement Record the depth If the depth reading deviates from the normal value or an error code is displayed the Locator should be returned for service U1 IN UJ NJ rL DIGICAT 500i 550i Functional Checks 89 DIGICAT 500i 550i Functional Checks CE Functional test check list 90 If any of these tests give no response or a significantly different response from normal the Locator should be returned for service Functional Test Check List Unit Serial Number Comments Locator Test Operative Fail analysis Notes Yes No N A 1 Casing Return for repair Casing should be free of Replace damage 2 Labels Return for repair Body labels must be legible Replace and intact Display label must be free of damage and tears 3 Battery hatch Return for repair Replace Hatches mu

Leica DIGICAT 500i/550i User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents