GDO-7v3 User Manual.indd - Automatic Technology Australia
Contents
1. z U Q Y 0 gt D m O TM Featuring TrioCode Technolog matic TECHNOLOGY aut smart simple secure INSTALLATION INSIRUCTIONS OWNERS COPY WARNING It is vital for the safety of persons to follow all instructions Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and or property and remote control opener damage Please save these instructions for future reference Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology Australia Pty Ltd Garage Door Opener Automatic Technology Australia Pty Ltd hereby further expressly excludes all or any liability for any injury damage cost expense or claim whatsoever suffered by any person as a result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener in accordance with these installation instructions O GDO 7v3 SecuraLift Owner Installation Instructions O GDO 7v3 SecuraLift Overhead Garage Door Opener Important Safety Instructions Features Operating Controls Package Contents Installation Knockdown C Rail Assembly C Rail Attachment Determine the Door Type Mounting on2. Step 5 Mounting the Wall Bracket a A Centre the bracket over the intersection of these two lines Mark centres for at least two holes Fig 15 e Ensure this is into a solid mounting point Drill holes into the wall with an appropriate bit Secure to the wall using IF CONCRETE OR BRICK 8mm or 5 6 loxins or dynabolts IF TIMBER wood screw 20 or equivalent minimum 50mm lono WARNING Make sure concrete brick wall or timber lintels are solid and sound so as to form a secure mounting platform Step 6 Attach the Rail to the Wall Bracket a Attach the c rail assembly to the wall bracket with the 90mm long clevis pin and secure with the supplied snap pin Fig 16 Leave the powerhead in its packing box for protection during installation Step 7 Secure the Powerhead to the Ceiling a Raise the powerhead from the packing box and support it in the horizontal position with a step ladder Open the garage door Rest the opener on the open door and use a scrap piece of wood to bring it to horizontal level Line up the track perpendicular to the wall Secure the perforated angle not supplied to the ceiling above where powerhead s mounting holes will be once fully installed A representative mounting is shown Fig 17 Connect the powerhead to the ceiling mounted perforated angle with M8x20mm screws and nuts Strips should not extend more than 18mm below centre of powerhead mounting holes Go to St
3. Auto courtesy light The SecuraLift courtesy light comes on automatically whenever the door is activated The light can also be switched on and off without operating the door by coding a dedicated button on a TrioCode transmitter The light will stay on for approximately three minutes then switch off This time is adjustable Vacation mode A hand held transmitter can be programmed to lock and unlock all other transmitters that have been programmed into the openers memory The vacation mode can be used when the door is left idle for long periods of time Pet Pedestrian mode The hand held transmitter can be programmed to open the door partially so that the family pet can enter and exit the garage at any time You may also wish to open the door to a height suitable only for pedestrian access The door opening position is also programmable Auto close mode The opener can be programmed to automatically close after an open cycle The auto close time is adjustable It is compulsory to install a P E Beam if this mode is selected otherwise the door may cause personal injury or damage to property Photo Electric P E Beam optional The opener has an input for a P E beam to be connected for extra safety protection and use of the auto close mode Manual operation The opener is equipped with a unique manual disengaging device If the power to the opener is disrupted for any reason the door can be put into manual mode by pulling down on
4. Controller fuse NOTE 60 secs 3 mins 1 sec 255 secs 2 1 26 0 secs 1 sec 255 secs 230V 240Va c 50Hz 2 2 Watts 250 Watts 1 3 HP Alternating Current 3 1m approx Standard 3 850m with extension 5500mm 16 5m 3000mm 100kg 800N 80kg 600N 60kg 150N 15kg UHF Multi frequency FM Receiver 24 X 4 button Transmitter Codes UHF Multi frequency FM Transmitter TrioCode Over 4 29 billion random codes Non linear encryption algorithm CR2032 3 Volts Edison screw mount 240V 60W rough service or construction type 5A slow blow 1 The door must be well balanced A person should be able to lift the door up manually with very little effort in case of an emergency 2 Intermittent operations may occur in areas which experience very strong winds Strong wind puts extra pressure on the door and tracks which may in turn trigger the safety obstruction detection system intermittently 3 P E Beams should be fitted as added safety in case of entrapment Owner Installation Instructions GDO 7v3 SecuraLift O 29 30 O Troubleshooting Door will not operate Door starts to close but automatically reverses to open position Door operates from drive unit OPERATE button but not from transmitter See note Door will not close fully Door will not open fully Courtesy light not working Globe keeps blowing Auto close not working PLEASE NOTE Mains power not switched on Door
5. 17 Step 11 1 Alternative Mounting Option The opener can be fastened to the roof by driving a bolt through the C Rail into a structural timber support The bolt head s height must not exceed 6mm Fig 21 Mounting Door Bracket amp Arms Step 12 Mounting Door Bracket The door bracket comes in two parts The bottom plate with two mounting holes is used on its own for one piece doors For sectional doors the top plate is placed over the bottom plate and is fixed with four 4 screws Fig 22 a Mount the door bracket or bracket assembly on the door s centre line one third down the top panel Fig 22 using M or equivalent screws not supplied b STEEL DOORS ONLY Bracket can be welded in place NOTE If in doubt about the door s strength N reinforcement may be added to the door s frame where necessary Door damage may occur if the bracket is installed on a panel with insufficient strength The opener s warranty does not cover damage caused to the door and or door panels Step 13 Attaching the Arms FOR SECTIONAL AND ONE PIECE DOORS WITH TRACK a Assemble the bent arm connecting to the door to the right side of the straight arm connecting to the shuttle with bolts and nuts supplied in the accessory pack Fig 23 Always use both bent and straight arms b Connect the assembled arm to the bracket and the disengaged trolley with clevis and snap pins The angle A must be more than 10 Fig 2
6. Each press of Button 1 will allow you to inch the door open Keep doing this until the door reaches the desired open limit position Ifthe door is opened too far press Button 4 to inch the door towards closed IMPORTANT WARNING The door will automatically close open and close again once Step 15 3 f is performed Ensure that no persons or objects are in the door s path f When happy with the open limit position press Button 2 on the transmitter to store into memory g The door will now automatically close and open to calculate the safety obstruction settings After this the opener can be operated with the OPERATE button Step 15 4 Resetting the Door Limit Positions Limit positions can be deleted by the following steps a Follow Steps 14 5 a and b as outlined overleaf b Repeat Steps 15 1 and 15 3 to set new travel limit positions gt There is no need to re code the transmitter Step 15 2 upon restting travel limits The transmitter will still be stored in memory Button 1 Inch Open Button 4 Inch Close Switch between fast and slow inching Owner Installation Instructions GDO 7v3 SecuraLift O 19 20 ta 30 Safety Obstruction Force Test O O22 amp x Wood 40mm high GDO 7v3 SecuraLift Owner Installation Instructions A WARNING Take care when testing or adjusting the Safety Obstruction Force Excessive force ma
7. O 31 32 O GDO 7v3 SecuraLift Owner Installation Instructions Spare Parts 1 301 488 2 8 8000 23 8 yood O80L NNZ 8 dSS dVNS Nid LAN SONV14 8 SZX8W M3Y9S 6Z80 Nid SIA31O Wav 1N38 Wav 9 gt INIT LNIOP NIVHO TOZ M SANIT 8 Lx Z NIVHO 8xFN SHO Sa MANOS YIS SSNYHL 0 84 19 4184230848 LOSL LYOddNS 43430848 ZEXOZXGZL 48943 8 MOVYL LOSL ASSY JILLNHS ZdA ASSY STGNVH NIHLS NNZ dSS dVNS Nid 0680 Nid LOSL 13XOVY8 TIYM LOS L ASSY NIVHO NOISNAL A X3dNI LOSL 064 2 5 LOSL 00 3 18 S 43930 aI ST0 LNOO 9 x S EW udu MIYOS ZAY dS 88 340 LHN YIHSYM 49071 HLOOL LNI OLXPN S MIYOS 8W LAN X3H LAS S V ASSY YOO YIMOd S08OV qtHVO8 TOYLNO9 8X N udu MIYOS ALLL AV ONISNOH 08 OLXPN GHL Hd Su MANOS 3LILdV L 38079 3 2988 LANWONS 4189 0865 8 ASSY ONIWLL 1 1 YaddOHO 292986 tidddOHO NMOHS LON 8 348 4388 1 6 6XZ ZLXS 8Z HSN OZ dOV ONINdS Nid
8. P E Beam s path is broken the Auto close timer has been set If the P E path is not broken the door will remain open until the path is broken If the opener incurs a physical obstruction i e not from the P E Beams while closing the door will re open and not Auto close until the P E Beam s path is broken again Step 22 1 Setting Auto close Time a Hold down the AUTO CLOSE TIME button Fig 35 b While holding in the AUTO CLOSE TIME button press the PLUS button each press will add one second to the Auto close delay To decrease the delay time follow Step 22 1 a and press the MINUS button each press will deduct one second from the Auto close delay d Press the OPERATE button or transmitter to open the door When the door is fully opened the OPEN LIMIT LED will flash to indicate that Auto close mode is operational e Break the P E Beam s path momentarily to initialise Auto close When the door reaches the fully opened position the door will pause for the set Auto close time and then close Receiver Model PE 2 Transmitter ta LIMIT TUS CLOSE 7S cos LIMIT i D TUM UST Owner Installation Instructions GDO 7v3 SecuraLift O 25 26 Final Set Up Step 23 Setting of Courtesy Light Time The preset courtesy light time is three minutes This time can
9. Position a Press and hold the MINUS or PLUS buttons to move the door to the halfway position Ensure that the door shuttle and chain index are engaged b Using a small screwdriver turn the DATUM ADJUST screw until the STATUS LED comes on Fig 26 Ifthe STATUS LED is already illuminated when the door is halfway up turn the DATUM ADJUST screw until the light goes off then turn back one notch to illuminate again Step 14 4 Set the Limits Positions a Press and hold the MINUS button until the door reaches the desired close limit position Single presses will the inch the door closed Fig 27 b Press the LIMIT SET button to store the close position into memory Fig 27 c Press and hold the PLUS button until the door reaches the desired open limit position Single presses will the inch the door open Fig 27 IMPORTANT WARNING The door wil N automatically close open and close again once Step 14 4 d is performed Ensure that no persons or objects are in the door s path d Press the LIMIT SET button to store the close position into memory Fig 27 e The door will now automatically close and open to calculate the safety obstruction settings After this the opener can be operated with the OPERATE button Step 14 5 Resetting the Door Limit Positions Limit positions can be deleted by the following steps a Press and hold the MINUS button for six 6 seconds until you hear three beeps and
10. is obstructed Door is locked or motor jammed Door tracks hardware damaged The opener is in vacation mode Adverse weather conditions wind or cold causing door to stiffen and become tight in the tracks Possible obstruction in the doorway Transmitter code not stored in memory Flat battery Broken battery lead inside transmitter Door limits positions need to be reset Door limits positions need to be reset Globe down Incorrect globe voltage must be 240V AC PE Beam or wiring faulty PE Beam not aligned correctly PE Beam is obstructed Door obstructed when closing Auto close time not set Auto close mode not set Switch on mains power Remove obstruction Unlock door or remove jam Door requires service repair by qualified technician Turn off vacation mode Increase force margin setting See page 20 or re calculate force margin Remove obstruction Code transmitter in to openers memory Refer step 18 1 on page 22 Replace battery Send transmitter to installer or Automatic Technology for repair Reset limits positions Step 15 4 page 19 Reset limits positions Step 15 4 page 19 Replace globe Edison type 240V 60W Replace globe Edison type 240V 60W Repair PE Beam or replace wiring Re align optics Remove obstruction from path of RE Remove obstruction See Step 22 on page 25 See Step 22 on page 25 Some areas may be prone to excessive
11. only be changed by the PG 3 programmer Step 24 Setting the Pet Mode position The default Pet Mode height can be changed as follows a Make sure the door is closed then press and hold the PLUS button for six 6 seconds Fig 43 until you hear three beeps and the OPEN and CLOSE LEDs flash rapidly b Press the PLUS or MINUS button to move the door to the desired pet mode open position c Press the SET button to record the new position When activated Pet Mode drives the door to the preset position from either above or below Pet Mode s active status is indicated by both the OPEN and CLOSE LIMIT LEDs being illuminated If a Pet Mode button is pressed while the door is moving the door will stop If a Pet Mode button is pressed when the door is in the Pet position then the door will close Step 25 Installing the Wall Mounted Transmitter Optional a Remove the faceplate from the transmitter b Affix the baseplate in a convenient wall location Fig 44 that is the door is visible from this location but out of the reach of children at a height of at least 1 8 meters from the floor c Replace the faceplate d To code the transmitter see Step 19 on page 20 Step 26 Re initialising the Opener a Press and hold the SET Button for two 2 seconds the beeper will sound once Fig 45 b The door will start to move and re calculate force margins The door can move between the open and close limit positions u
12. open door Fig 19 NOTE Do not slide rail along the face of the door Step 10 Mounting the C Rail a Close the door slowly The rail will be elevated by the top edge of the door as it moves b Stop the door when it is at its highest point of travel Allow 25mm additional height for clearance between the door and the track Fig 20 c Support the Rail in this position and close the door d The height determined in Step 10 b will be the height at which to mount the wall bracket e Centre the bracket along the line determined in Step 8 f Using the bracket as a template mark a minimum of two holes and drill with appropriate size bit For a more secure fitting the wall bracket can be anchored using more than two holes g Secure the bracket to the wall using IF CONCRETE OR BRICK 8mm 5 6 loxins dynabolts IF TIMBER wood screw 20 or similar min 50mm h Attach the bracket and C Rail with supplied pins Fig 16 WARNING Make sure concrete brick wall or timber lintels are solid and sound so as to form a secure mounting platform Step 11 Secure the Powerhead to the Ceiling a Secure the perforated angle not supplied to the ceiling above where powerhead s mounting holes will be See Fig 17 for a representative mounting b Connect the powerhead to the ceiling mounted perforated angle with M8x20mm screws and nuts Strips should not extend more than 18mm below centre of powerhead mounting holes Fig
13. radio interference brought on by devices such as cordless telephones wireless stereo headphones and baby monitors It is possible that these devices could cause a degree of interference such as to greatly reduce the range of the transmitter In such an instance please contact your Automatic Technology dealer for an alternative frequency replacement kit As this is not a warrantable situation but an environmental issue charges may apply for the change over O GDO 7v3 SecuraLift Owner Installation Instructions Maintenance Maintenance The SERVICE LED will indicate the requirement for a service and or adjustment To reset the SERVICE LED when the door is serviced reorogram the Door Travel Limits and the Door Travel Force on completion of this programming the SERVICE LED will go out Whilst your opener does not require any periodic maintenance the door that it is fitted to does Your garage door is a large heavy moving object and should be tested regularly to ensure it is in good condition A poorly maintained door could cause fatal or serious injuries or serious damage to property To ensure a long and trouble free life for your opener the following is recommended Monthly Disengage the opener and manually operate the door The door must be smooth to operate by hand An operating force on the bottom rail should not exceed 150N 15kg force e Each month check that the opener reverses when the door contacts a 50mm high obje
14. simple secure an alesco company www ata aust com au
15. the CLOSE LIMIT LED starts to flash b Release the CLOSE button c Repeat Steps 14 1 to 14 4 to set new travel limit positions O Setting Limits via Transmitter The GDO 7v3 has the unique ability to set travel limits using the transmitter allowing the installer to move around the garage and door to better assess the desired close and open limit positions Step 15 1 Power Up and Set the Datum a Follow Steps 14 1 to 14 3 as outlined overleaf Observe all warnings Step 15 2 Code a Transmitter for Limit Setting a Press and hold the DOOR CODE button Fig 28 b Press Button 1 on the transmitter for two seconds Fig 29 Release and pause for two seconds Press the same button again on the transmitter for two seconds c Release the DOOR CODE button Step 15 3 Setting Limits via Transmitter a Press and hold Button 4 on the transmitter to close the door When the door is approx 2cm from the ground press and hold Button 3 for two seconds and release Fig 29 b Each press of Button 4 will allow you to inch the door closed Keep doing this until the door reaches the desired close limit position Ifthe door is closed too far press Button 1 to inch the door towards open c When happy with the close limit position press Button 2 to store this in memory d Press Button 1 to open the door When approx 2cm from the desired open position press and hold Button 3 for two seconds then release
16. the same button again for two 2 seconds c Release the DOOR CODE BUTTON d Press the transmitter button to test Step 18 2 Coding a Transmitter Button to the Courtesy Light The transmitter can be programmed to operate the courtesy light on the opener independently of the door moving a Press and hold LIGHT CODE button Fig 34 b Press one of the four buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 seconds c Release the LIGHT CODE button d Press the transmitter button to test Step 18 2 Code a Transmitter Button to Enable Vacation mode The opener can be programmed into a Vacation Mode where the opener will not respond to any transmitter except the button of the transmitter the one programmed for vacation mode a Briefly press the DOOR CODE button once then press it again and hold will beep two times on second press Fig 35 b Press one of the four 4 buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 seconds c Release DOOR CODE button d Press and hold the transmitter button for six 6 seconds to set Vacation Mode the door code led will stay lit while vacation mode is active e To reset Vacation Mode press the same button for two seconds Step 18 3 Code a Transmitter Button to Enable AUX OUTPUT a Briefly press the DOOR CODE button two 2 times
17. the string handle on an angle towards the door This will allow you to manually open or close the door To re engage the opener pull the string handle away from the door Owner Installation Instructions GDO 7v3 SecuraLift O Operating Controls 01 PROG INPUT is used to connect of the Automatic Technology Handheld Programmer for the purpose of editing control and receiver functions 02 Terminal Block 24V PWR is used to power photo electric beam PE Input for photo electric beam for safety gt PE Ov is used to supply 0 volts to photo electric beam gt GND is used with OSC input or AUX out put gt O S C INPUT is used for the connection of a wired switch momentary contact This switch can then be used to open stop or close the door Install the wall switch in a location where the switch is out of reach of children and the garage door is visible AUX output can be used to control alarm system 03 SET button orange is used during the installation phase together with the Open and Close buttons to set the door limit positions The Set button is also used to re initialize the Opener OPERATE button Yellow is used during installation to test the open stop and close cycles for the opener The opener has to be initialised by the Reset button to make the O S C button operable 05 PLUS button green is used during installation to help set the open limit position Pressing and holding
18. 4 WARNING Connecting the bent arm other way A around may damage the door The straight arm should not protrude beyond heal of bent arm FOR ONE PIECE DOORS WITHOUT TRACK a Assemble the bent and straight arms as shown in Fig 25 with bolts and nuts supplied in the accessory pack Always use both the bent and straight arms b Connect the assembled arm to the bracket and the disengaged trolley with clevis and snap pins c If installing on a door with a bad wave action lengthening the arm will assist in reducing this effect IMPORTANT NOTE Adjust the length of the cord so that its toggle is no more than 1 8m from the ground Straight arm connected to the shuttle Bent arm onnected to the door 9 Owner Installation Instructions GDO 7v3 SecuraLift O 17 18 Setting Limits O GDO 7v3 SecuraLift Owner Installation Instructions NOTE If P E Beams are to be used they must be installed before setting the travel limits Step 14 1 Remove Controls Cover Remove the controls cover to access the control panel Replace it when setup is completed Step 14 2 Connect Power to the Powerhead Plug the power cord into a mains point and switch power on The red CLOSE LIMIT LED will be flashing WARNING The safety obstruction detection N system is inoperable while MINUS and PLUS drive buttons are being used and travel limits are not set Step 14 3 Set the Datum
19. E the power on and hold until all LEDs are off SET O GDO 7v3 SecuraLift Owner Installation Instructions Opens Stops Closes the door Codes a transmitter button for operate function Codes a transmitter button for light function Increases the obstruction force margin setting Decreases the obstruction force margin setting Reloads the factory set default obstruction force margin setting Increases the auto close delay time Decreases the auto close delay time Reloads the factory set default auto close delay time Clears the door limits set positions Limits then need to be reset Enters pet pedestrian position mode Deletes control parameters excluding transmitter storage memory Deletes all transmitter storage memory Deletes all control parameters and transmitter storage memory Re initialises the Opener to re calculate force margin O Default Settings amp Specifications Factory Default Settings wwwHFr Maximum motor run time Courtesy light time Obstruction force margin Auto close time Technical Specifications Power supply Standby power Motor power Motor type Shuttle travel distance Maximum shuttle travel distance in the C Rail Maximum door opening Width Height Weight Short term peak force Lift force Nominal force Receiver type Receiver code storage capacity Transmitter frequency Coding type Number of code combinations Code generation Transmitter battery Courtesy light
20. YOOT TAS 01x0z 4048 388 8 SW 33 48 X3H ASSY 34 XZ WHOM OWASLZ ZX W1I3ATOd dVO LXE MIYOS GVSH NVd SOd 80 0 009 3OO1T8 TWNINYAL NMOHS LON IA 037 8 X90078 TWNINYAL ZHOS AOEZ G60 Z9 W4 MOSZ HOLLOW O Y f9 ZZ 01 9 r ANO SL YOLIOWdWO 0800 OPSLN 12512 3 YSHSVM ONIdS HAVIA SI8 V1N YIHSYM LSNYHL 9 69 LAVHS SAG 1 8 8 S 9r 3svg xoguvgo 0 001 Hsng 98 GI 8 asya 33 Owner Installation Instructions GDO 7v3 SecuraLift 34 O Warranty and Exclusion of Liability 10 11 This warranty is not transferable 13 This warranty is an addition to any non excludable conditions or warranties that are implied into this contract by relevant statute including the Trade Practices Act 1974 Cwth Subject to all of the matters set out below Automatic Technology Australia Pty Ltd ATA warrants a overhead door opener drive units for twenty four 24 months or 5000 cycles whichever occurs first and b all components and accessories for twelve 12 months from the date of purchase specified in the sales docket receipt as free of any defects in material and workmanship This warranty applies only where the purchaser a immediately notifies ATA or the retailer of the alleged defect b returns the product to the retailer and c presents the relevant sa
21. a Track Type Door Mounting on a non Track Type Door Mounting Door Bracket amp Arms Programming the Opener Setting Limits Setting Limits via Transmitter Safety Obstruction Force Safety Obstruction Force Test Adjustin Safety Obstruction Forces Coding Transmitters Door Courtesy Light Vacation Mode Pet PedestrianjMode Remotely Coding Transmitters Deleting Transmitter Codes Accessories Photo Electric Beam Auto Close Final Set Up Courtesy Light Time Pet Mode Door Height Wall Mounted Transmitter Re Initialising Parameters Door Status Indicators Button Functions System Specifications Troubleshooting Guide Maintenance Spare Parts Warranty Owner Installation Instructions GDO 7v3 SecuraLift 10 11 11 13 14 15 16 17 18 18 19 20 20 21 22 22 22 22 23 24 24 25 25 25 26 26 26 26 26 27 27 28 29 30 31 33 34 Important Safety Instructions WARNING It is vital for the safety of persons to follow all instructions Failure to comply with the following Safety Rules may result in serious personal injury and or property damage CAUTION If your garage has no pedestrian entrance door an emergency access device should be installed This accessory allows manual operation of the garage door from outside in case of power failure For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a Photo Electric P E Beam In most count
22. ach time the PLUS button is pressed to indicate a force increase Ifthe OPEN LIMIT LED lit continuously when pressing the PLUS button this indicates that the maximum setting has been reached Test the force again as per Steps 16 1 and 16 2 Step 17 2 To Decrease Force Pressure a b a Hold down FORCE MARGIN SET button Fig 32 While holding the FORCE MARGIN SET button press the MINUS button Each press decreases the force margin The CLOSE LIMIT LED will flash each time the MINUS button is pressed to indicate a force increase f the OPEN LIMIT LED lit continuously when pressing the PLUS button this indicates that the maximum setting has been reached Test the force again as per Steps 16 1 and 16 2 Step 17 3 To Recall Factory Set Force a While holding down the FORCE MARGIN SET button press the LIMIT SET button for two 2 seconds Release both buttons The default setting should now be recalled OPEN LIMIT Osis a ose G O DATUM ADJUST AUTO CLOSE TIME Owner Installation Instructions GDO 7v3 SecuraLift O 21 22 Coding Transmitters O GDO 7v3 SecuraLift Owner Installation Instructions Step 18 1 Code a Transmitter Button for Door Operation a Press and hold the DOOR CODE button Fig 33 b Press one of the four buttons on the transmitter for two 2 seconds pause for two 2 seconds then press
23. b Using a small needle press and hold firmly for two seconds through the Coding Hole Fig 38 c WITHIN 10 SECONDS take the additional transmitter you wish to code Decide which button that you want to activate the function to be duplicated e g activate the door or turn on the courtesy light d Hold the new transmitter s button for two seconds pause for two seconds hold again for two seconds and then release e Wait for 10 seconds and then press the new transmitter s button to test Step 20 Deleting Programmed Codes Step 20 1 Deleting a Stored Transmitter Code a Selectthe transmitter you want to delete b Press and hold the DOOR CODE BUTTON Fig 39 c Press the transmitter button you would like to delete for two seconds pause for two seconds press again for two seconds and then release d Release the DOOR CODE BUTTON The code should now be deleted Confirm this by pressing the transmitter button the function e g door opening should not respond Step 20 2 Deleting All Transmitter Codes a 1 Turn off power to the opener b While switched off press and hold the DOOR CODE BUTTON Fig 39 Turn on power to the opener while holding this button c The OPEN LIMIT CLOSE LIMIT and DOOR STATUS LEDs will illuminate for about five seconds These LED s will turn off and the CODING LED will illuminate d Release the DOOR CODE BUTTON All stored codes will now be deleted Confirm this
24. ct placed on the floor AS3350 Refer to Testing the Safety System Step 16 NOTE If the door does not operate smoothly call your installer Service Record Yearly Automatic Technology suggests you contact your installer to perform an annual door service CAUTION Frequently examine door particularly cables springs and mountings for signs of wear damage or imbalance Do not use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury AS3350 Adjustments should only be carried out by experienced persons as this function can be dangerous if not performed under strict safety procedures WARNING Failure to maintain your garage door may void the warranty on your garage door opener Warranty Expired Indicator When the opener reaches the number of cycles covered by warranty the courtesy light will flash 10 times after each operation to indicate that the warranty has expired This flashing will continue for twenty 20 operations unless the user acknowledges the warranty expiry indicator and stops the light from flashing To stop the courtesy light flashing press the LIMIT SET button while the light is flashing after an operation Record any maintenance in the following table to assist in any warranty service Date Service by Signature Invoice No Amount Owner Installation Instructions GDO 7v3 SecuraLift
25. ct carried out within Australia This warranty does not cover consumable items including globes batteries and fuses Where the Product is retailed by any person other than ATA except for the warranty set out above such person has no authority from ATA to give any warranty or guarantee on ATA s behalf in addition to the warranty set out above NOTES 1 One 1 cycle one 1 open and one 1 close action of the door or gate 2 This warranty is to be read in conjunction with the owner s copy of the installation instruction manual 3 The door should be balanced in such a way that the user manually is able to open or close the door without using O force not greater than 150N 15kg although a greater force may be required for the start of the movement GDO 7v3 SecuraLift Owner Installation Instructions smart simple secure September 2008 Automatic Technology Australia Pty Ltd All rights reserved TrioCode and SecuraLift are trademarks of Automatic Technology Australia Pty Ltd No part of this document may be reproduced without prior permission In an ongoing commitment to product quality we reserve the right to change specification without notice E amp OE Automatic Technololgy Australia Pty Ltd au tm a t i ABN 11 007 125 368 6 8 Fiveways Boulevard TECHNOLOGY Keysborough Victoria 3173 Australia P 1300133944 61 2 9722 5666 International Enquiries Only E sales ata aust com au smart
26. ctly and tested for operation at regular intervals Extreme caution is recommended when using auto close mode All safety rules must be followed In order for the SecuraLift to sense an object obstructing the door way some force must be exerted on the object As a result the object door and or person may suffer damage or injury If the power supply cord is damaged it must be replaced by an Automatic Technology service agent or suitably qualified person Make sure that the door is fully open before driving in or out of the garage and fully closed before leaving the driveway Make sure that remote controls are kept out of reach of children Install the optional wall switch or optional wall mounted transmitter in a location where the garage door is visible but out of the reach of children at a height of at least 1 8 meters from the floor Owner Installation Instructions GDO 7v3 SecuraLift O 5 Features Operation To open or close the door simply press a button on a TrioCode handheld transmitter a wall mounted transmitter or optional wall switch for two seconds During open and close cycles the door can be stopped by pressing the button again The next actuation will move the reverse the door s direction TrioCode Code Hopping Technology Every time a TrioCode transmitter is used a new security code is randomly generated from over 4 29 billion possibilities This greatly enhances the security of the system an
27. d makes code grabbing a thing of the past These transmitters also overcome interference issues by simultaneously sending a signal over three slightly different frequencies Even if two of the three signals are jammed the system will still work S ALPS Semi Automatic Limits Positioning System The S ALPS system does away with manual adjustment of the door s limits position using mechanical parts such as cams and microswitches During installation the handheld transmitter can be programmed to set the limits positions Anti travel electronic brakes The SecuraLift features an anti travel electronic brake mechanism to ensure the opener stops the door at exact location ISS intelligent safety obstruction system While the door is performing a close cycle should it hit an obstacle or be restricted in some manner it will automatically reverse The amount of force the door should encounter before reversing is automatically adjusted by the doors control system during the initial installation of the automatic door opener The door will also stop if restricted whilst opening The Safety Obstruction Force should be checked at least once a month See installation manual for instructions O GDO 7v3 SecuraLift Owner Installation Instructions O Overload indicator When the maximum opening and closing capacity of the SecuraLift is exceeded the red and green Limits LEDs flash alternately to indicate that an overload has occurred
28. ep 14 on page 18 A WARNING The opener must be securely fastened to structural supports otherwise opener failure may ensue causing serious personal injury and or property damage Z 4 Me 258 ogee S SD EE A Owner Installation Instructions GDO 7v3 SecuraLift O Mounting on a non Track Type Door Centre of Door Step lade J Step dden Drill hole at centre of track recommended Y bolt size M or M8 Steel Rail HEIGHT OF BOLT HEAD Shuttle Assembly 16 O GDO 7v3 SecuraLift Owner Installation Instructions WARNING The opener must be securely fastened to structural supports otherwise opener failure may ensue causing serious personal injury and or property damage Step 8 Determine the Door s Centre a Find the centre of the door and mark this location both above the door and on top of the door b Draw two lines 21 5mm either side of this Fig 18 Step 9 Prepositioning the Opener a Raise the door to open position b Rest the opener on the top edge of the door with end of the rail against the wall Fig 19 c Support the powerhead level with the lowest point of the
29. huttle back to the centre of the track to re test the force with spring scale Fig 08 k Continue to adjust adjust the tension hex bolt until a force of 8kg to 8 5 Kg is achieved Step 2 Secure C Rail to Drive Unit a Locate and insert the shaft of drive unit into the C Rail s sprocket Fig 09 b Fix the two track brackets with four screws supplied in accessory pack Fig 10 Owner Installation Instructions GDO 7v3 SecuraLift O 13 Step 3 Determine Door Type Determine which type of garage door you have as illustrated below Fig 11 to 13 For a sectional panel door on tracks Fig 11 proceed with the installation from Step 4 Sectional door with track For a one piece door on tracks Fig 12 proceed with the installation from Step 4 One piece door with track For a one piece door without tracks on springs Fig 13 proceed with the installation from Step 8 One piece door without track 14 O GDO 7v3 SecuraLift Owner Installation Instructions Mounting on a Track Type Door Step 4 Determine Bracket Position a b Open the door and find the highest point of travel of the top door panel Using a level transfer this height to the wall above the door Fig 14 and mark a line 60mm above it Determine the centre point on the wall above and on top of the door Draw two lines extending 21 5mm from each side of the centre point Fig 15
30. les docket and this warranty document to the retailer to confirm the date of purchase Except for this warranty ATA gives no warranties of any kind whatsoever whether express or implied in relation to the product and all warranties of whatsoever kind relating to the product are to the extent permissible by statute hereby excluded To the extent permissible by statute ATA disclaims any liability of whatsoever nature in respect of any claim or demand for loss or damage which arises out of a accidental damage to or normal wear and tear to the product or to the product s components b any cost relating to damage resulting from wear and tear c blown fuses loss or damage caused by electrical surges power surges or power spikes d loss or damage due to theft fire flood rain water lightning storms or any other acts of God e maximum continuous operating time exceeding one 1 minute in ten 10 f maximum operating force exceeding 15kg 150N when moving the door manually to the open or closed position g door surface area and or weight exceeding 16 5m and 100kg respectively h door not in safe and correct working order and condition i evidence of unauthorised repairs J any cost relating to damage caused by misuse negligence or failure to maintain the equipment in a proper working order as per clauses d through h k installation adjustment or use which is not in accordance with the instructions set out in installati
31. ns without adequate supervision Children should be supervised to ensure that they do not play with the remote transmitters or the opener Keep hands and loose clothing clear of the door and door opener at all times O GDO 7v3 SecuraLift Owner Installation Instructions Important Safety Instructions The unit should be installed so that it is protected from the elements It should not be exposed to water or rain It is not to be immersed in water or sprayed directly by a hose or other device The garage door must be well balanced Sticking or binding doors must be repaired by a qualified garage door installer prior to installation of the opener Frequently examine the installation in particular cables springs and mountings for signs of wear damage or imbalance DO NOT use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury DO NOT attempt to repair the door yourself as hardware is under extreme tension Remove or disengage all garage door locks and mechanisms prior to installation of the opener Connect the opener to a properly earthed general purpose 240V mains power outlet installed by a qualified electrical contractor Disconnect the power cord from mains power before making any repairs or removing covers Only experienced service personnel should remove covers from the opener When using auto close mode a photo electric beam must be fitted corre
32. on instruction manual I attempted or complete modification or repairs to the product carried out by a person who is not authorised or has not been trained by ATA to carry out such modification or repairs m faulty or unsuitable wiring of structure to which the product is fixed or connected n radio including citizen band transmission or any electrical interference o damage caused by insects p loss or damage to any property whatsoever or any loss or expense whatsoever resulting or arising there from or any consequential loss q any cost or expense arising due to manufacturer recall of any product r any cost or expense due to negligence of the approved service provider s installation of a residential garage door opener in a commercial or industrial situation or a non single residential dwelling liability under this warranty is limited at ATA s absolute option to replacing or repairing the product which ATA in its unfettered opinion considers to be defective either in material and or workmanship or to credit the dealer with the price at which the product was purchased by the dealer This warranty does not extend to cover labour for installation This warranty is limited to Return to Base RTB repair and does not cover labour for on site attendance This warranty is void if the Product is not returned to the manufacturer in original or suitably secure packaging This warranty is only applicable for repairs to the produ
33. p to four 4 times depending on the position of the door and the power up condition c A single beep will be heard once the initialisation is complete The door is now ready for use O GDO 7v3 SecuraLift Owner Installation Instructions OPEN Z X Q LIMIT CLOSE Zao 3 e LIMIT TIME DATUM Parameters Door Status Indicators Door Opener State OPEN LED CLOSE LED Red Beeper STATUS Green LED Yellow On Open Close Opening Closing Door travel stopped Door obstructed when opening Door obstructed when closing Opener overloaded Door in open position with Auto Close mode selected Mains power interrupted Service due Flashing Flashing Flashing Alternating flashes One second flashes Rapid flashes On Flashing Flashing Flashing Beeps as door moves Alternating flashes 3 beeps at the start of each cycle Owner Installation Instructions GDO 7v3 SecuraLift On 27 28 Parameters Door Status Indicators Yw y OPERATE DOOR CODE LIGHT CODE FORCE MARGIN SET amp PLUS FORCE MARGIN SET amp MINUS FORCE MARGIN SET then SET AUTO CLOSE TIME then PLUS AUTO CLOSE TIME then MINUS AUTO CLOSE TIME then SET MINUS for 6 secs PLUS for 6 secs SET then power on amp hold until all LEDs are off DOOR CODE then power on amp hold until all LEDs are off SET amp DOOR COD
34. pressing buttons on any previously coded transmitters the opener should not respond 24 O GDO 7v3 SecuraLift Owner Installation Instructions P E Beams amp Auto close Step 21 Fitting the P E Beams optional a Affix the P E Beams in a strategic location within the doorway We recommend 150mm above the floor level and as close as possible to the door opening inside the garage b Connect the wires from the P E wiring harness to terminal block Fig 40 The wiring diagram is for Model PH 2 Order Code 90214 Make sure to align the beams correctly Follow the manual supplied with the P E Beams WARNING When using Auto Close Mode and P E AN beams the doorway must be clear of all obstructions and persons at all times The location of the beam sand manner in which it is installed might not give safety protection at all times Check to make sure that the height of the beam and type used give maximum protection possible WARNING Install the P E Beams as per diagram in N Fig 46 Tampering with P E Beams could result in serious personal injury and or property damage and will void the warranty Step 22 Setting Up Auto close Mode IMPORTANT NOTICE It is compulsory to have P E Beams installed when using Auto close mode Auto close mode is a function that automatically closes the door a pre set time after the P E Beams recognise that a vehicle has left the garage The Auto close timer only starts after the
35. ries P E Beams are mandatory on all garage doors fitted with automatic openers For a small additional outlay Automatic Technology recommends that Photo Electric Beams be installed with the automatic opener ensuring additional safety and peace of mind DO NOT operate the opener unless the garage door is in full view and free from objects such as cars and children people Make sure that the door has finished moving before entering or leaving the garage DO NOT operate the opener when children persons are near the door Children must be supervised at all times when the SecuraLift is in use Serious personal injury and or property damage can result from failure to follow this warning DO NOT allow children to operate the SecuraLift Serious personal injury and or property damage can result from failure to follow this warning Regularly check to make sure that the safety obstruction force is working correctly and is tested and set as per page 20 of this manual Failure to follow these instructions could result in serious personal injury and or property damage This test must be repeated at regular intervals and the necessary adjustments made as required Doors requiring over 400N of force to move must have P E Beams installed DO NOT disengage the door opener to manual operation with children persons or any other objects including motor vehicles within the doorway The door opener is not intended for use by young children or infirm perso
36. ssembly on piece of wood until track sections are flush Repeat with remaining track sections c Remove chain from package and lay chain out on sg 03 floor do not allow chain to twist d Loop the chain onto the pulley of tension chain assembly Slide the tension chain assembly with s chain into the track Fig 04 e Slide shuttle assembly into opener end the track assembly be sure to insert shuttle assembly with hole side toward the door as shown with arrow in Fig 05 Push the sprocket support into opener end of the track f Feed the chain through the shuttle assembly then through the sprocket support and loop around the sprocket then feed back through the sprocket support and shuttle assembly Join to chain index with chain links supplied Fig 05 Idler pulley Shuttle with hole side toward the door Owner Installation Instructions GDO 7v3 SecuraLift O 11 12 Knockdown C Rail Assembly O Tension hex bolt Centre of the track GDO 7v3 SecuraLift Owner Installation Instructions Note Use the 8 teeth sprocket with Gdo 7v3 opener h Engage the shuttle with the chain index and move shuttle assembly to the centre of track Make sure the chain is engaged into the sprocket and also wrapped around the centre of the pulley i Use a spring scale to measure required force to pull the shuttle adjust 1 2 tension hex bolt Fig 07 to tension the chain Move the s
37. then press it again and hold will beep three times on third press Fig 36 b Press one of the four buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 second c Release the DOOR CODE button d Press the transmitter button to test Step 18 4 Code a Transmitter Button for Pet Pedestrian Mode a ao Briefly press the DOOR CODE button three times then press it again and hold will beep four times on fourth press Fig 37 Press one of the four buttons on the transmitter for two 2 seconds pause for two 2 seconds then press the same button again for two 2 seconds Release the DOOR CODE button Press the transmitter button to test To change the default pet pedestrian door opening position refer Step 24 Owner Installation Instructions GDO 7v3 SecuraLift O fig 23 Coding Transmitters Step 19 Remotely Coding Transmitters Using this method transmitters can be coded without Coding hole j access to the opener s control panel as long as a pre coded transmitter is available IMPORTANT NOTE The door or courtesy light must activate when the steps below are performed This indicates that the pre coded transmitter is in range of the opener and the correct button has been pressed w a Take any pre coded transmitter Press the button Small needle for the function to be duplicated and release
38. this button will move the door in the open direction releasing stops the door NOTE The safety obstruction detection is inoperable when the PLUS button is used to move door G OPEN LIMIT LED green the LED is very helpful during installation It illuminates and flashes when the door is opening and remains steady on when the open limit position has been reached 07 FORCE MARGIN SET Button The obstruction force margin is set automatically during installation The margin can be adjusted manually using the Force Margin Set button White Holding the Force Margin Set button and pressing Plus or Minus buttons will increase or decrease the amount of force The Force Margin Set should only be used if environmental factors wind etc affect the door s operation 08 LIGHT CODE button white is used for storing or erasing the transmitter button code you wish to use to switch the courtesy light on the opener on or off 09 CODING LED red light flashes when a code is being stored or when a transmitter button is pressed 10 DOOR CODE BUTTON blue is used for storing or erasing the transmitter button you wish to use to command the door to open stop or close DOOR STATUS LED Yellow MINUS button red is used during installation to help set the close limit position Pressing and holding this button will move the door in the close direction Movement stops when the button is released NOTE The safety obstruction detec
39. tion is inoperable when the MINUS button is used to move door CLOSE LIMIT LED red the LED is very helpful during installation It illuminates and flashes when the door is closing and remains steady on when the close limit position has been reached Datum adjust screw is used during limits set up to indicate the mid point of the door s travel AUTO CLOSE TIME button White is used to adjust the auto close time While holding in the AUTO CLOSE TIME button and then pressing the open button the time is increased Each press will increase the time by 5 seconds Pressing the close button will decrease the time O GDO 7v3 SecuraLift Owner Installation Instructions O 629 LIMIT SET E ee Ge AN BY 10 O Package Contents Gdo 7v3 Securalift drive unit 1 TrioCode keyring transmitters 2 TrioCode wall mounted transmitter not available all models 1 C rail track pack Fig 02 1 Pack includes three C rail sleeves and four C rail tracks Chain 1 Shuttle assembly 1 Door attachment arms 2 Hardware pack 1 Installation Manual 1 GDO 7v3 SecuraLift Owner Installation Instructions 9 O Knockdown C Rail Assembly Step 1 Knockdown C Rail Assembly a Place track pieces on flat surface for assembly All the track sections are interchangeable 5 b Slide sleeve onto the track section Fig 03 Connect track by sliding sleeve onto next track section Tap track a
40. y cause SERIOUS PERSONAL INJURY and or PROPERTY DAMAGE Step 16 1 Testing Close Cycle a b Press the OPERATE button to open the door Fig 30 Place a piece of timber approximately 40mm high on the floor directly under the door Fig 31 Press the OPERATE button to close door The door should strike the object and start to re open Step 16 2 Testing Open Cycle A Press the OPERATE button to close the door Fig 30 Press again to open the door When the door reaches the half open point grab the bottom rail of the door firmly and the door should stop If the door does not reverse readily when closing or stop when opening the force may be excessive and need adjusting refer below DANGER If the door fails these tests put the opener into manual mode only operate the door by hand and call for service Adjusting Safety Obstruction Forces Adjusting Safety Obstruction Force The Safety Obstruction Force is calculated automatically during setup Adjusting this is normally only necessitated by environmental conditions such as windy or dusty areas and areas with extreme temperature changes A d WARNING Doors requiring over 400N of force to move must have P E Beams fitted for safety Step 17 1 To Increase Force Pressure Hold down FORCE MARGIN SET button Fig 32 While holding the FORCE MARGIN SET button press the PLUS button Each press increases the force margin The OPEN LIMIT LED will flash e
Download Pdf Manuals
Related Search